Schreinerei und Küchenwerkstatt

Condition: used, Year of construction: 2024, Exhibition machine Garbsen, new, complete in standard configuration with: Iedjxy Tl Depfx Agqoa - Sturdy, torsion-free steel frame, welded and bolted construction - Upper lamella press beam with 6 elements, side lamella press beam with 5 elements - Lamella press beams featuring proven tolerance compensation system (System Ganner) for tightly pressed carcass joints - Counterpressure surfaces (side pressure wall, bottom) are 38 mm thick, coated, continuous support panels - Continuous pressing surface height of 95 mm on the lower vertical press beam - Electromotive adjustment of both press beams via precision trapezoidal spindle screws (with increased pitch and concentricity accuracy) and high-performance recirculating nuts with grease reservoir - Pressing is carried out electromotively, by 2 separate helical geared motors (2 x 0.75 kW) - The pressing force of the press beams is infinitely electronically adjustable using two potentiometers and regulated via frequency converters; the pressing force control is therefore absolutely wear-free - Pressing force for the horizontal press beam: min. 500 daN (kg) up to infinitely adjustable max. 2200 daN (kg) - Pressing force for the vertical press beam: min. 300 daN (kg) up to infinitely adjustable max. 2200 daN (kg) - Pressing and adjustment speed of the press beams with fine positioning via 3-stage selector switch: 5 / 10 / 25 mm/second - Extremely simple operation via 6 separate push buttons, 8 movement processes can be selected via the control system - Freely adjustable pressing time preselection with automatic opening, 0–30 min (switchable to seconds or hours) - Working height/loading height: 300 mm - Working dimensions: length min: 150 mm, max: 2500 mm; height min: 150 mm, max: 1400 mm; depth: 700 mm - Electrical connection: 400V, 3Ph, 50Hz (3.2 kW, 16 A) - Weight: 2100 kg (net) - Dimensions: 3500x1200x2300 mm (L x W x H) Image includes special accessories: machine feet. Surcharge for rapid traverse speed per unit for fast positioning of the press beams, controlled via automatic workpiece detection with sensors in the press beams. Pressing speed: 5 / 10 / 25 mm/sec and rapid traverse speed: 50 mm/sec. Sensors can be deactivated for pressing special components. Set of machine feet for working height 500 mm per unit. Location: Garbsen

Condition: refurbished (used), Year of construction: 2016, LAMELLA - CARCASE PRESS GANNOMAT « CONCEPT 70 ECO » Complete in standard configuration with: - Sturdy, torsion-resistant frame made of steel in welded and bolted construction - Upper lamella pressing beam with 6 elements, side lamella pressing beam with 5 elements - Lamella pressing beams with proven tolerance compensation system (Ganner system) for tightly pressed carcase joints - Counterpressure surfaces (side pressure wall, base) made from 38 mm thick, coated, continuous support panels - Continuous pressing surface with a height of 95 mm on the lower vertical pressing beam - Electromotorical adjustment of both pressing beams via precision trapezoidal-thread spindles (with increased pitch and concentricity accuracy) and high-performance traveling nuts with grease reservoir - Pressing is carried out electrically via 2 separate worm gear motors (2 x 0.75 kW) - The pressing force of the beams is infinitely electronically adjustable via 2 potentiometers and regulated by a frequency inverter, resulting in absolutely wear-free pressing force control - Pressing force for horizontal pressing beam: min. 500 daN (kg) up to steplessly max. 2200 daN (kg) Pressing force for vertical pressing beam: min. 300 daN (kg) up to steplessly max. 2200 daN (kg) Pressing and adjustment speed of the beams with fine positioning via 3-stage selector switch: 5 / 10 / 25 mm/second Very easy operation Iedpjxvitiefx Agqoa - Working height/loading height: 300 mm - Working dimensions: length min: 150 mm, max: 2500 mm height min: 150 mm, max: 1400 mm depth: 700 mm Machine No. 563.624 400V, 3Ph, 50Hz (3.2 kVA, 16 A) Set of machine feet for 500 mm working height Operating manual in German language Completely overhauled by Ganner, 6 months parts warranty Location: Ex stock 54634 Bitburg - immediately available -

Condition: used, Year of construction: 1989, Working dimensions 3000 x 1250 x 650 mm Cylinder stroke 110 mm Machine dimensions 3240 x 2120 x 770 mm Weight approx. 900 kg Iodpfx Agexu Egvjqja

Condition: used, Year of construction: 1993, used, in excellent condition Brand: Hess Model: Express Ijdpfx Asxuv N Usgqja Year of manufacture: 1993 Machine no.: 100914/28 Cylinders per press element: 2 - 110 mm stroke Number of press elements horizontal: 3 Number of press elements vertical: 3 Working width: 2500 mm Working height: 1350 mm Press depth: 600 mm Pneumatic Height adjustment: electric Space requirement approx. 3600 x 800 x 2450 mm Weight approx. 1200 kg Location: 97447 Gerolzhofen, loaded free on truck, unpacked Delivery in current condition as inspected, without warranty or guarantee

Condition: excellent (used), Year of construction: 2015, Carcass clamp for pressing furniture carcasses, manufactured by the Homag-group, HOMAG AUTOMATION. With this pressing concept no prepositioning of the press elements is necessary. Vertical, horizontal pressure frames are powered electromotively and act as a self-lock via the trapezoid spindles. As crossing pressure lamellas process way to the inserted workpieces and ensure an all-over coating pressure construction on the carcass parts. Features • All-over coating pressing • Pressing surfaces with tolerance balance • Pressing speed: 25 mm/s • Pressing power: 15 kn • Carcass length: 250 - 2.500 [mm] Iedpexpfniefx Agqea • Carcass depth: 250 - 700 [mm] • Carcass height: 150 - 1.400 [mm]

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, machine/vehicle number: 941, working height: 1,350 mm, working width: 600 mm, working length: 2,500 mm, TECHNICAL DETAILS Pressing length: max. 2,500 mm Pressing height: max. 1,350 mm Working depth: max. 600 mm MACHINE DETAILS Electrical data Rated voltage: 3/N/PE/400 V Rated current: 11 A Rated power: 4.7 kW Frequency: 50 Hz EQUIPMENT Vertical and horizontal press beams operated electromechanically Pressure build-up via frequency-controlled geared motors Vertical and horizontal press pressure adjustable separately Pressing time adjustable Iedpfjxnyg Rsx Agqja

Condition: good (used), Year of construction: 2014, Used carcass press - GANNOMAT Concept 70 Eco Isdexhc T Tjpfx Agqsa - Year of manufacture: 2014 - Available December 2025

Condition: excellent (used), Hess Corpus Press Type: Export, Pneumatic Manufacturer: Hess Type: Export Maximum workpiece size: 2,500 x 1,500 mm Press force: 1,400 kp pressing capacity per pressure unit at 15 bar Vertical cylinders: 2 + 2 pressure cylinders Horizontal cylinders: 2 + 2 pressure cylinders Dimensions: 3,900 mm x 2,500 mm x 600 mm Weight: 1,060 kg Hess Corpus Press Export, pneumatic 2 vertical pressure assemblies, each with 2 pressure cylinders, 80 mm cylinder diameter, 110 mm stroke, 1,400 kp pressing force per pressure unit at 15 bar 2 horizontal pressure assemblies, each with 2 pressure cylinders, 80 mm cylinder diameter, 110 mm stroke, 1,400 kp pressing force per pressure unit at 15 bar; the upper unit is easily adjustable thanks to weight compensation Pressing operation is controlled via 2 rotary slide valves with positions Press – Stop – Release Iodpfsxgvwpjx Agqsa Maintenance unit consisting of pressure regulator (0–15 bar), pressure gauge, and oil mist lubricator Anodized measuring scales, detachable feet Location: Ex works customer site - Immediately available -

Condition: good (used), Year of construction: 1999, functionality: fully functional, machine/vehicle number: LGMATECH KORPUSSPRESSE, Body press in immediately operational condition. The press can be inspected at any time by appointment. Isdpfjxf Dvwox Agqoa

Condition: used, Year of construction: 1982, Press dimensions: 3500 x 2600 mm Electrohydraulic unit for 4 hinge cup drillings, complete, 4 hinge cup drilling units Left upper corner plate with 2 cross pressure cylinders 4x hydraulic wood holders Intermediate inserts for small pressing with drilling unit Central pressure beam 2600 mm Longitudinal pressure cylinder with counterholder 4x hinge cup drills Storage location: At customer site Iedpjxftcasfx Agqja

Condition: excellent (used), Year of construction: 2016, LAMELLA – CASE CLAMP PRESS GANNOMAT “CONCEPT 70 ECO” Complete in standard configuration including: - Sturdy, torsion-resistant steel frame, constructed with welded and bolted assemblies - UPPER lamella pressure beam with 6 elements, SIDE lamella pressure beam with 5 elements - Lamella pressure beams feature the tried-and-tested tolerance compensation system (Ganner system) for tightly pressed carcass joints Iedpfx Agjw Td A Ijqja - Counter-pressure surfaces (side pressure wall, bottom) are 38 mm thick, coated, continuous support plates - Continuous pressing surface with a height of 95 mm on the lower vertical pressure beam - Electromotive adjustment of both pressure beams via precision trapezoidal thread spindles (with increased pitch and concentricity accuracy) and high-performance lead nuts with grease reservoir - Clamping is electromotor-driven, with two separate worm gear motors (2 x 0.75 kW) - The pressing force of the pressure beams is continuously adjustable electronically using two potentiometers and regulated via frequency inverters, providing a completely wear-free press force control - Pressing force for horizontal beam: min. 500 daN (kg) up to stepless max. 2200 daN (kg) Pressing force for vertical beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Press and adjustment speeds of the pressure beams with fine positioning, switchable via 3-stage selector: 5 / 10 / 25 mm/sec - Extremely user-friendly operation - Working height/loading height: 300 mm - Working dimensions: Length min: 150 mm, max: 2500 mm; Height min: 150 mm, max: 1400 mm; Depth: 700 mm - Machine No. 563.624 - 400V, 3Ph, 50Hz (3.2 kVA, 16 A) Set of machine feet for 500 mm working height Operating manual in German Overhauled by Ganner, with 6-month parts warranty Location: ex stock 54634 Bitburg - Immediately available -

Condition: excellent (used), Year of construction: 2013, LAMELLAR - CASE CLAMP GANNOMAT "CONCEPT 70 ECO" Complete in standard configuration with: Iedew Tdymjpfx Agqoa Case joints. - Counter-pressure surfaces (side pressure wall, base) are 40 mm thick, coated, continuous support plates - Electrically operated adjustment of both press beams via precision trapezoidal-thread spindles (with increased lead and concentricity accuracy) and high-performance running nuts with grease reservoir. - Clamping is performed electrically using two separate worm gear motors (2 x 0.75 kW) - Pressing force: 2000 daN (kg) per press beam. - The pressing force of the press beam is electronically regulated and set via frequency converter, thus torque transmission is completely wear-free. - Pressing and adjustment speed: 25 mm/sec. - Very simple operation via 6 separate push buttons; 6 movement operations can be selected via the controller. - Freely adjustable pressing time preselection with automatic opening: 0-30 min (switchable to seconds or hours). - Working height/feeding height: 300 mm - Working dimensions: Length min: 150 mm, max: 2550 mm; Height min: 150 mm, max: 1400 mm. Depth: 700 mm 1 selector switch for variable pressing force: 1000 / 1500 / 2000 daN (kg) Machine No. 380.324 400V, 3Ph, 50Hz (2.5 kVA, 16 A) Set of machine feet for working height 500 mm Machine used: Year of construction: 2013, fully overhauled by Ganner, 6-month parts warranty Special price: ex-stock 54634 Bitburg - immediately available -

Condition: excellent (used), Year of construction: 1995, Pneumatic clamp for furniture. Usable dimensions: 3000x1200 mm. Motorized lifting of the upper bar. Tested and working. Iodpfx Asw S A Erogqea

Condition: new, Year of construction: 2025, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Fully equipped in standard configuration with: - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir - Pressing is performed by electromotor via worm gear motor (0.75 kW) - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Iedpew Sgnksfx Agqsa Electrical connection: 400 Volt, 50 Hz, 16 A Available: at short notice

Condition: used, Year of construction: 1999, total height: 2,200 mm, total length: 5,200 mm, total width: 800 mm, Empty weight: 950 kg - Year: 1999 - Documentation available: No Iedpfx Agowyn Nasqsa - CE certificate present: No - Serial number: 13301 - Press drive: Pneumatic - Max. workpiece width [mm]: 4500 - Max. workpiece height [mm]: 1550 - Max. workpiece depth [mm]: 600 - Vertical pressing rams [pcs]: 3 - Horizontal pressing rams [pcs]: 4 - Transport dimensions: 5200mm x 800mm x 2200mm (l x w x h) - Transport weight [kg]: 950kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, Complete in standard design with: - Sturdy, torsion-free steel frame, of welded and bolted construction - PRESS BEAMS LATERALLY with continuous pressure surface and 25 mm thick, coated bearing plate - Counter-pressure surfaces (lateral pressure wall, base) are 25 mm thick, coated, continuous bearing plates Iedpfewx Nfgjx Agqsa - Electric adjustment of the press beam via precision trapezoidal-thread spindles (with increased lead and concentricity accuracy) and high-performance lead nuts with grease reservoir - Pressing is performed electromechanically using a worm gear motor (0.75 kW) - The pressing force of the press beam is continuously adjustable electronically by potentiometer and regulated by a frequency inverter, offering absolutely wear-free pressure force control - Pressing force for the vertical press beam min. 300 daN (kg) to infinitely variable max. 2200 daN (kg) - Press and adjustment speed of the press beams with fine positioning, via 3-position selector switch 5 / 10 / 25 mm/second - Extremely simple operation via two separate push buttons; two movement cycles (open/close) selectable via control - Freely adjustable pressing time pre-selection with automatic opening, 0–30 min. (switchable to seconds or hours) - Working height/loading height 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400V, 3Ph, 50Hz (1.6 kVA, 16 A)

Condition: excellent (used), functionality: fully functional, planing width: 630 mm, height adjustment type: mechanical, overall weight: 1,100 kg, planing height: 200 mm, working width: 630 mm, rotational speed (max.): 5,500 rpm, Thickness planer Dornburg, model DD 63. Robust thickness planer (cast iron), table length approx. 1050 mm. Planing width approx. 630 mm, maximum clearance height 200 mm. Cutterhead equipped with 4 strip knives. Motor 5.5 kW, speed 5500 rpm. Feed rate 18 m/min. Dimensions approx. 1100 x 1300 x 1600 mm (LxWxH). Weight approx. 1100 kg. Iodpfswtqzrjx Agqea

Condition: excellent (used), Hydraulic assembly press Italprasse Program/30 for door and window joinery The Italpresse Program/30 machine is a hydraulic vertical press designed for precise assembly and gluing of wooden elements, such as window and door frames and furniture bodies. Thanks to its design, it allows for precise fitting and permanent connection of components, which is crucial in the production of door and furniture joinery. Technical specifications •Maximum working dimensions: 3000 × 1700 mm •Stroke of vertical cylinders: 800 mm Isdpfx Aowkf Stsgqja •Stroke of horizontal cylinders: 1200 mm •Adjustable lower beam: can be set in three positions •Hydraulic cylinders: •2 vertical (Ø 100/60 mm) •2 horizontal for setting frames (Ø 50/35 mm) •Power of hydraulic unit: 2.2 kW •Overall dimensions: 3600 × 1000 × 2650 mm •Weight: approx. 1200 kg Application Italpresse Program/30 is ideal for: •Gluing and assembling window and door frames •Assembling furniture bodies •Assembling wooden panels and other construction joinery elements

Condition: new, Year of construction: 2025, functionality: fully functional, Gannomat Concept 70 Eco body press Year of manufacture 2025 including the following options: - Rapid traverse speed adjustment speed up to 50 mm/sec - Machine feet (working height 500mm) The Concept Eco and Concept Primus are ideal assembly aids for dowel connections when pressing bodies together, as well as when making drawers. Brief introduction: • With tried and tested tolerance compensation (GANNOMAT system) • 2 potentiometers for continuously adjustable pressing force • Pressing force min. 300/500 daN (kg) for Concept Eco or Pressing force min. 600/800 daN (kg) for Concept Primus • Pressing force max. 2200 daN (kg) for Concept Eco or Pressing force max. 3500 daN (kg) for Concept Primus • 3 pressing and adjustment speeds 5/10/25 mm/sec. (with fine positioning / creep speed) • Freely adjustable pressing time pre-selection with automatic opening • Concept Eco: Simple operation via 6 separate push buttons for 8 movement sequences • Concept Primus: Simple operation via LCD display Universal application area: • Bodies e.g. for furniture and cabinets • Mitered bodies Ijdpfx Agsvxgrrsqsa • Bodies with protruding lids • Drawers • Pressing several bodies / drawers Advantages: • Tried and tested tolerance compensation (GANNOMAT system) • Electromechanical body press with frequency-controlled gear motors • Independent vertical and horizontal press beam • Long service life thanks to tried and tested, high-quality components • Solid and robust construction • Space-saving design • Body pressing = Simple + Fast + Efficient + Flexible + Precise + Professional • Simple thanks to simple and practical control panel • Fast thanks to press beam positioning speed of up to 50 mm/sec (option) • Efficient thanks to precise pressing of a wide variety of body sizes • Flexible thanks to adjustable parameters such as e.g. Pressing force, pressing time, travel speeds • Precise through precise angle pressing of furniture bodies and drawers • Professional production of bodies and drawers using modern body presses

Condition: good (used), Code: 0024 Brand: ITALPRESSE Model: NUOVO/SP Quick setting semiautomatic case clamp Technical data Manual loading Max useful dimensions mm 2500 x 600 x 1250 Min useful dimensions mm 250 x 600 x 280 Motorized horizontal cross-beam with display Vertical beam setting Ijdpfjvv Ul Usx Agqoa N° 6 vertical cylinders N° 6 horizontal cylinders Cylinders stroke mm 70 Cross-beam stroke mm 920 Installed power Kw 0,55 Overall dimensions mm 3600 x 800 x 2550 h Weight kg 1400

Condition: used, Year of construction: 1992, Dimensions: 5700 x 1300 x 2400 mm Iodpfx Aevvkl Djgqsa Storage location: Nattheim

Condition: good (used), ZIM Hülsta cabinet press NOW Easy Make: ZIM Hülsta-Werke Type: NOW Easy Ser. no.: 380125028 Carcase max. 260 x 1100 mm 2 supports at the bottom, movable Ijdovdbv Aopfx Agqoa 2 press bars at top, movable Beckoff control panel Roller conveyor 4500 x 600 mm Roller width: 500 mm Overall dimensions: W x D x H 3300 x 1800 x 3600 mm Further articles - new and used - can be found in our store! International shipping costs on request!

Condition: excellent (used), functionality: fully functional, VERTICAL CLAMP PRESS , HYDRAULIC , model ITALPRESSE PROGRAM 30 second hand machine operation in manual and/or automatic mode with automatic piston opening timer volt. 380/50 technical data: max. useful working dimensions mm. 3000 x 1700 min. useful working dimensions mm. 250 x 340 hydraulic pump , motor power Hp 2 adjustable vertical pressure adjustable horizontal pressure movable control panel base with height adjustment Isdpjuxdprofx Agqsa overall dimensions mm 3600 x 1000 x 2340 (H)

Condition: used, Year of construction: 2024, machine/vehicle number: 1300.448, Neue Ausstellungsmaschine! Listenpreis: 32.665,- € komplett in Standardausführung mit: Stabiler, verwindungsfreier Rahmen aus Stahl, in Schweiß- und Schraubkonstruktion - Lamellen-Pressbalken OBEN mit 6 Elementen, Lamellen-Pressbalken SEITLICH mit 5 Elementen - Lamellen-Pressbalken mit praxisbewährtem Toleranzausgleich (System Ganner) für dicht verpresste Korpusverbindungen - Gegendruckflächen (Seitendruckwand, Boden) sind 38 mm starke, beschichtete, durchgehende Auflageplatten - Durchgehend Pressfläche mit Höhe 95 mm am Vertikal-Pressbalken unten - Elektromotorische Verstellung der beiden Pressbalken über Präzisions-Trapezgewindespindeln (mit erhöhter Steigungs- und Rundlaufgenauigkeit) und Hochleistungs-Laufmuttern mit Fettreservoir - Die Verpressung erfolgt elektromotorisch, über 2 getrennte Schneckengetriebemotoren (2 x 0,75 kW) - Die Presskraft der Pressbalken ist durch 2 Potentiometer stufenlos elektronisch eingestellt und über Frequenzumformer geregelt, daher ist die Presskraft-Regelung absolut verschleißfrei - Presskraft für Horizontal-Pressbalken min. 500 daN (kg) bis stufenlos max. 2200 daN (kg) - Presskraft für Vertikal-Pressbalken min. 300 daN (kg) bis stufenlos max. 2200 daN (kg) - Press- und Verstellgeschwindigkeit der Pressbalken mit Feinpositionierung, über 3-Stufen-Wahlschalter 5 / 10 / 25 mm/Sekunde - Einfachste Bedienung über 6 getrennte Drucktaster, 8 Bewegungsabläufe sind über Steuerung wählbar - Frei einstellbare Presszeitvorwahl mit Öffnungsautomatik 0-30 min (umschaltbar auf Sekunden oder Stunden) - Arbeitshöhe/Beschickungshöhe: 300 mm - Arbeitsabmessungen: Länge min: 150 mm, max: 2500 mm Höhe min: 150 mm, max: 1400 mm Tiefe: 700 mm Iedpfeuf Hx Hsx Agqoa Gewicht: ca. 1800 kg Netto Abmessung: (Länge x Breite x Höhe) 3,45 m x 0,95 m x 2,30 m Elektrischer Anschluss: 400V, 3Ph, 50Hz (3,2 kVA, 16A) Zusatzausstattungen: Eilgang-Verfahrgeschwindigkeit, für schnelles Positionieren der Pressbalken, gesteuert über automatische Werkstückerkennung mit Sensoren in den Pressbalken, Pressgeschwindigkeit 5 / 10 / 25 mm/Sek. und Eilgang-Verfahrgeschwindigkeit 50 mm/Sek., die Sensoren können abgeschaltet werden für die Verpressung von Sonderteilen 1 Satz Maschinenfüße (Abrbeitshöhe 500 mm)

Condition: used, length: 2.300 mm width: 800 mm height: 2.700 mm Iodpfx Agst H Tuxjqea Workpiece size: 130 x 70 x 145 cm Pneumatic carcass press or gluing press for pressing furniture carcasses or similar.