Coupled signal transmission board

HOMAG

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Polishing unit 2 motors Lodpfx Agoyqybuoxjri Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, power: 19 kW (25.83 HP), travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,730 mm, number of spindles: 20, number of tool stations in tool turret 1: 18, TECHNICAL DETAILS Working area X-axis: 4,175 mm Working area Y-axis: 1,730 mm Number of suction traverses: 8 Tool magazine positions: 18 Spindles Number of spindles for vertical drilling: 17 Number of spindles for horizontal drilling (X-direction): 2 Number of spindles for horizontal drilling (Y-direction): 1 Total number of spindles: 20 Lrjdpfsyttf Sjx Agxsi Milling unit Number of controlled axes: 4 Motor power: 18.5 kW Automatic tool changer Liquid-cooled MACHINE DETAILS Total installed power: 19 kW Control model: PC85 EQUIPMENT CE marking Front safety cover Note: Cones, milling cutters, and aggregates are not included in the scope of delivery. Safety fences are supplied based on availability (left side only). The machine is sold and delivered in its actual and legal condition (‘as seen and approved’), based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer is entitled to inspect the goods prior to collection, and assumes responsibility for installation, safety, and use of the machine at the destination. External reference: 6906

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,550 mm, workpiece height (max.): 40 mm, number of spindles: 30, travel speed (max.): 80,000 mm/min, TECHNICAL DETAILS Travel range X-axis: 4,175 mm Travel range Y-axis: 1,550 mm Travel speed X-axis: 80 m/min Travel speed Y-axis: 80 m/min Travel speed Z-axis: 30 m/min Maximum workpiece height: 40 mm Number of suction traverse beams: 8 Spindles Number of spindles for vertical drilling: 20 Number of spindles for horizontal drilling in X-direction: 10 Total number of spindles: 30 Milling unit Number of controlled axes: 4 + Flex5 Motor power: 15 kW Automatic tool changer Liquid-cooled Saw unit Tool magazine 1 Number of slots: 18 Tool magazine 2 Number of slots: 10 Lrjdpfxoyttcws Agxoi EQUIPMENT NC positioning of suction units Vacuum pump PowerControl P85 control system WoodWop 5.0 machine programming software Note: Cones and milling cutters are not included in the scope of delivery. The machine is sold and delivered in its actual and legal condition ("as seen and approved") on the basis of photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and is responsible for installation, securing, and usage of the machine at the destination. External reference: 7350

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed speed: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Number of motors: 2 Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool changer with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 4 Unit: Top Mill Model: UF11 Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Model: MN21 with NC positioning Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Total installed power: 35 kW Lredpjytr Hbefx Agxsi EQUIPMENT Spray unit PowerControl PC22 machine programming software CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and descriptive technical/commercial data. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, safeguarding, and use of the machine at the destination. External reference: 6216

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, workpiece height (max.): 60 mm, edge thickness (max.): 20 mm, controller model: POWER CONTROL PC22, rotational speed (max.): 12,000 rpm, Auction extended by one week due to updated technical data! TECHNICAL DETAILS Workpiece dimensions Panel height: min. 12 mm Panel height: max. 60 mm Edge thickness: min. 0.4 mm Edge thickness: max. 20 mm Milling and Glue Application Unit Pre-milling unit: available Motor power: 3 kW Speed: 9,000 rpm Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Edge Processing Unit 1 End trimming: available Number of motors: 2 Motor power: 0.80 kW Speed: 12,000 rpm Edge Processing Unit 2 Rough top and bottom flush trimming: available Number of motors: 2 Motor power: 1.5 kW Speed: 12,000 rpm Edge Processing Unit 3 Corner rounding: available Number of motors: 2 Motor power: 0.4 kW Speed: 12,000 rpm Edge Processing Unit 4 Milling unit for rough machining: available Motor power: 4 kW Speed: 9,000 rpm Edge Processing Unit 5 Scraper blade Lrodeyqx U Hjpfx Agxei Edge Processing Unit 6 Glue scraper blade Edge Processing Unit 7 Polishing unit: available Number of motors: 2 Motor power: 0.18 kW Edge Processing Unit 8 Wide belt sanding unit: available Motor power: 1.5 kW Control software: POWER CONTROL PC22 Total connected load: 42 kW

Condition: good (used), Double-end tenoner, edge processing machine, scoring motor, chipper motor, spindle motor, milling motor Lrodpfxsb A Nx Dj Agxoi -Power: 0.23 kW -Speed: 18000 rpm at 300 Hz -Dimensions: 210/70/H100 mm -Weight: 2 kg

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, Working height: 900 mm Working width: 1,350 mm Belt changing side: left Workpiece thickness: 3 - 160 mm Frequency-controlled feed speed: 4 - 20 m/min Abrasive belt dimensions: 2,620 x 1,350–1,380 mm Adjustable sanding belt blowing device with 5 settings WRD WORKPIECE CLEANING ROTOR Workpiece cleaning system with 16 rotating nozzles MOBILE OPERATING TERMINAL powerControl with powerTouch SST SOFT STARTER Inrush currents are limited to prevent voltage drops GWRD BELT CLEANING PROGRAM Upon activation, the machine automatically sets to a 10 mm workpiece thickness and activates the blowing rotors. After the feed belt is fully cleaned, the machine returns to its initial setting. AAT EXTRACTION DAMPER CONTROL Control of extraction dampers via the terminal (24 Volt DC, without extraction dampers included) UPS EMERGENCY POWER SUPPLY FOR BELT CONTROL 1-3 PCS Uninterruptible power supply for sanding belt oscillation in case of power failure System consists of: SANDTEQ W-700, PROFI SWB735/RRE – sanding from below Wide belt sanding machine with three sanding units for processing wood or wood-like workpiece surfaces Prepared to accept up to two auxiliary units, such as a cleaning brush, satinizing or structuring brush, and rotating cleaning nozzles. Units: I. R UNIT Sanding unit with automatically adjusting contact roller Profiled steel roller, 240 mm diameter With grain compensation Drive motor: 37 kW Abrasive belt speed: 25 m/s - Automatic locking of the sanding unit for fast belt changes and increased process safety - Abrasive belt drives with electronic, wear-free brake - Optical, touchless abrasive belt tracking - Pneumatic abrasive belt tensioning with integrated belt edge compensation II. R UNIT Sanding unit with automatically adjusting contact roller Rubber-coated roller, 240 mm diameter Rubber hardness: 85° Shore With grain compensation Drive motor: 30 kW Abrasive belt speed: 18 m/s III. E UNIT Sanding unit for installing a pressure beam - Automatic locking of the sanding unit for fast belt changes and increased process safety - Abrasive belt drives with electronic, wear-free brake - Optical, touchless abrasive belt tracking Lrjdpfsyw Ndmex Agxoi - Pneumatic abrasive belt tensioning with integrated belt edge compensation - Protected storage area on the machine for additional sanding inserts Drive motor: 22 kW Abrasive belt speed: 2 – 18 m/s Torque-dependent standby operation to reduce energy consumption. ACP PNEUMATICALLY SUPPORTED PRESSURE BEAM - Adjustable sanding pressure via pressure regulator - Workpiece-controlled engagement and disengagement at the leading and trailing edges - Various sanding inserts, 80 mm wide, with different felt hardnesses Machine dimensions (L x W x H): 3,900 x 2,100 x 2,000 mm Machine weight: approx. 7,500 kg SANDTEQ B-700, PROFI SWT735/RRE – sanding from above Wide belt sander with three sanding units for machining wood or wood-based workpiece surfaces Units as above, additionally: FBM FINISHING BRUSH Brush unit with finishing brush Bristles: horsehair Diameter: 130 mm Drive motor: 0.75 kW Machine dimensions (L x W x H): 2,995 x 2,100 x 2,255 – 2,415 mm Machine weight: approx. 6,500 kg

Condition: excellent (used), FLEXIBLE SYSTEM OF SINGLE-SIDE EDGEBANDING (BATCH ONE) Composed of the following machines: Ljdpfx Asinigmogxjri M.01) PANELS HANDLING and RETURN SYSTEM Mod. PROFI TBR100/20/30/F M.02) SINGLE-SIDE EDGE BANDER (RIGHT-HAND machine)"HOMAG" Mod. Profi KAR350/12/A Panels thickness (min/max) mm 8 / 60 - Working width (min/max) mm 200 / 1200 Numerical Control / Software PC 22 Adjustable feeding speed (m/min ) 18 - 32 Panels in-feed system WZ 14/30 Pre-milling Unit (vertical joint trimmers) adjustable by N.C. (2 x Kw 3) DOUBLE Glueing Unit (P.U.R. Glue + Quick Melt unit) 2 x PU 34 Pressure zone (N.C. adjustment) - Edge coils supporting unit (No. 12 reels) Snipping (end-cutting) unit WK13 Rough Trimming unit (2 x Kw 055) Fine Trimming unit (Multi-profile, adjustable by N.C.) MF 21 (2 x Kw 0,55) Corner Rounding unit (Contour Trimming) FF 32 (4 x Kw 0,4) Multi-Profile Copying unit adjustable by N.C.(fine and contour trimming) FK 31 (30 m/min) recently added (in a technological "revamping" operation) Profile Scraping unit (Multi-profile, adjustable by N.C.) MN 21 (servo) Finish processing unit (Glue scraper + Buffing unit) FA 11 Jumping Milling grooving unit UF 11 (1 x Kw 4) M.03 ) PORTAL BRIDGE (UNLOADING/LOADING) "BARGSTEDT" Model. TFU200/L/30/12/S

Condition: excellent (used), Year of construction: 1999, functionality: fully functional, Workpiece & Performance Panel Formats: • Length 1,200–1,400 mm • Width 195 mm • Thickness 5–12 mm Line Performance (excerpt): • Multi-blade saw feed: 2–48 m/min • Pack assembly: max. 100 pieces/min • Packaging: up to 12 packs/min • Palletizing: up to 12 cycles/min Feeding & Cutting 1. BARGSTEDT TBP16/DG/30/22/S Gantry Feeder Vacuum gantry for feeding raw panels (fixed edge on the right) • Workpiece weight up to 100 kg • Capacity up to 5 cycles/min • Pallet return and light barrier safety system 2. BARGSTEDT TPP20/28/21/S Pallet Magazine Provision of empty pallets for feeding • Capacity approx. 12 pallets • Max. stack height 1,800 mm 3. BARGSTEDT TAR40/28/22 Décor Alignment Station Aligns panels for décor-oriented further processing 4. Multi-blade Circular Saw K34/G/2200 Longitudinal splitting with edge trimming • Feed speed 2–48 m/min • Cutting height up to 58 mm • Main motor 22 kW • 9 saw blades + 2 chippers 5. Brushing Unit (after longitudinal cut) Horsehair brush, working width 2,200 mm, with extraction 6. BARGSTEDT Cross-Cut Saw Station HPp11 Cross-cutting in throughfeed mode with pressure beam • Cutting width 2,200 mm • Pneumatic overhead pressure rollers Singulation & Transfer 7. BARGSTEDT TFV40/ZR/RL/22/13/02 Singulation Station Turner with compartments (2×8 compartments) for distributing multi-panel assemblies • Conveyor speed 10–50 m/min 8. BARGSTEDT Right-Angle Transfer (TW) 90° transfer with belt conveyors, feed up to 130 m/min For transfer to the profiling line Profile Processing (soundproofed) 9. HOMAG FR 20/08/10/S Longitudinal Profiling Double-sided format processing • 6 units per side • 6.6 kW per unit • Tool diameter up to 200 mm • Joint color application + drying 10. HOMAG FL 20/08/15/S Cross Profiling Double-sided end profiling Lredpfxjywxrae Agxoi • 6 units per side • identical performance structure • integrated edge sealing 11. Sonolit Soundproof Cabin Housing for both HOMAG profiling machines • Approx. 12,000 × 7,000 × 3,000 mm Post-processing 12. BARGSTEDT TTK44/21/14/02 Dry Turner Workpiece turning in throughfeed • up to 100 cycles/min 13. BARGSTEDT B017/R/19/12/2/S Brushing Unit Double-sided fine cleaning with extraction Packing 14. BARGSTEDT TVP40/L/14/02 Pack Assembly Station Automatic pack forming with 1st/2nd choice sorting • Panels 1,200–1,400 × 195 × 5–12 mm • Pack height up to 80 mm • Capacity 100 pieces/min 15. BARGSTEDT TVK40/R/14/02 Carton Station Folding and providing cartons prior to packaging • Up to 12 packs/min 16. BARGSTEDT TVA40/07/02 Paper Feeder Automatic application of protective paper • up to 10 packs/min guaranteed 17. Labelling Station Automatic pack identification (format range according to packaging data) Packaging 18. LP Maskin LPFK-2PFL-400 Shrinking Unit Fully automatic film packaging with shrink tunnel • Connection load 36–40 kW • Capacity up to 12 packs/min • Film width up to 800 mm 19. BARGSTEDT Belt Conveyor TFB20/017/04 with Air Shower Cooling section after the shrink tunnel Palletizing 20. BARGSTEDT TSH80/EO/14/08 Crosswise Package Stacking Automatic stacking of packages onto pallets • Packages up to 1,400 × 195 × 58 mm • Capacity max. 12 cycles/min 21. BARGSTEDT TBS0/D/30/08/S Swing Arm Stacker Layer-by-layer palletizing with vacuum suction cups • up to 6 cycles/min • Package weight up to 50 kg 22. BARGSTEDT PP20/12/08 Pallet Magazine Automatic provision of empty pallets for final palletizing

Condition: used, machine/vehicle number: 008395, X axis working area: 3050 mm Y axis working area: 1250 mm Lrodpoygtcqsfx Agxei Main Electrospindle power: 10 KW Number of controlled axes: 3 axes Total number of drilling spindles: 27 Total number of tool changer positions: 8