Bale press

HSM V-Press 860 plus B

Condition: excellent (used), Year of construction: 2015, operating hours: 20,331 h, functionality: fully functional, pressing force: 100 t, filling opening width: 970 mm, filling opening length: 1,800 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, overall weight: 33,000 kg, Good day, We hereby offer you, without obligation, a used, complete baling press line consisting of a baler manufactured by HSM, type VK 8818 R-FU, including conveyor technology and wire tying stations. The following technical data was taken from the manufacturer's operating manual and brochures, for which we cannot guarantee accuracy or completeness. Technical Data – Baler: Manufacturer: HSM GmbH + Co. KG, Germany Type: VK 8818 R-FU Year of manufacture: 2015 Operating hours: 20,331 hours (as of September 2025) Number of bales pressed: 29,020 bales (as of September 2025) Press force (main press): 1000 kN Specific pressing force: 120 N/cm² Shear edge ejector force: 121 kN Feed opening dimensions: 970 x 1,800 mm Theoretical cycle time (idle): 8.3 seconds Theoretical output capacity: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length adjustable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency-controlled Connected load: 110 kW Nodpsyz Af Eefx Aa Ielc Total current consumption: 213 A Fusing: 250 A slow-blow Tying: 5-fold horizontal, fully automatic Output at bulk density: 20 kg/m³: 12.86 t/hour 50 kg/m³: 32.15 t/hour Bale weights (approx. 1.2 m bale length): 650 up to 750 kg per bale, material-dependent Hydraulic oil tank volume: 2000 L HVI 46 PLC control system: Siemens S7-300 Control panel: Siemens TP 700 Baler dimensions (assembled): 12,130 x 4,800 x 3,270 mm (L x W x H) Space requirement (with conveyor): 35,000 x 8,480 x 7,745 mm (L x W x H) Baler weight: approx. 33 t (main press approx. 12 t, press channel with bale clamp approx. 10 t) Additional Optional Equipment Ordered: – Frequency-controlled main drive, 2 x 45 kW, with up to 40% energy savings compared to the standard 2 x 45 kW drive, with same performance – Manual activation/deactivation of the number of wire bindings to save tying wire on non-expansive material – Shear edge ejector with 121 kN pressing force – Sensor-based wire monitoring, with baler shut-off in case of wire breakage or wire end – Bale chute – Optical warning signal, mounted on the control cabinet Condition of the Baler: The complete baling system (baler and conveyor technology) is in good, ready-to-use condition. The unit has been cleaned weekly, lubricated, and maintained according to manufacturer specifications by the operator. Technical Data – Chain Belt Conveyor: Manufacturer: Stadler Anlagenbau GmbH Type: Chain Belt Conveyor KF 1800 Year of manufacture: 2015 Belt speed: 0.36 m/second Feeder belt length: 7,000 mm Inclined belt length: 14,500 mm Gooseneck length: 1,550 mm Incline: 30° Nominal width: 1,800 mm Usable width: 1,638 mm Overall conveyor height: 7,745 mm Pit dimensions for conveyor: 11,200 x 3,000 x 1,250 mm (L x W x H) Scope of Delivery: – HSM VK 8818 R-FU baler – Maintenance platform – Bale chute – Wire diverting stations – Wire spool trolleys (without wire spools) – Stadler KF 1800 chain belt conveyor – Transverse sliding belt conveyor – Pit cover from feed conveyor to pit – Second control cabinet to operate the baler from the conveyor – Machine documentation in English Delivery Time: The complete system has already been dismantled, placed into storage, and can be loaded at short notice following receipt of payment. We would be pleased if this or one of our other balers might be of interest to you. Your Service Team Mertens & Frowein GmbH

Condition: good (used), Year of construction: 2011, operating hours: 40,000 h, functionality: fully functional, pressing force: 88 t, filling opening width: 990 mm, filling opening length: 1,800 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, overall weight: 23,000 kg, oil tank capacity: 2,000 l, power: 90 kW (122.37 HP), volume flow: 643 m³/h, Good day, We hereby offer, subject to prior sale, a used baler including conveyor belt, wire tying stations, and bale chute from the manufacturer HSM GmbH + Co. KG, model VK 8818 FU. The following technical specifications were taken from the manufacturer's operating manual and brochures; we do not assume any liability for the correctness or completeness of this information. Manufacturer: HSM GmbH + Co. KG, Germany Model: VK 8818 FU Year of manufacture: 2011 Operating hours: approx. 40,000 hours as of July 2025 Main press force: 880 kN Specific press force: 107 N/cm² Feed opening dimensions: 990 x 1,800 mm Theoretical throughput: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length adjustable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency-controlled Tying: 5-fold horizontal, fully automatic Baler dimensions (set up): 12,130 x 4,800 x 3,270 mm (L x W x H) Overall installation dimensions with conveyor system: 14,000 x 23,000 x 7,745 mm (L x W x H) Note: The machine was used in a recycling facility for compacting paper, cardboard, and film. The press is in good condition and will be replaced with a new, larger press in May/June 2026. Until then, the machine can be inspected in operation with material. We would be pleased if this baler is of interest to you. Nedpfx Aeymmtcja Iolc Your Mertens & Frowein GmbH service team

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Nsdpfx Aajzbxwij Iolc Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: good (used), Year of construction: 2021, operating hours: 245 h, functionality: fully functional, HSM V-Press 860 plus vertical baling press, year of manufacture 2021 Technical data: Nlsdpfey Tvzdsx Aa Iec Manufacturer: HSM Type: V-Press 860 plus Year of manufacture: 2021 Operating hours: 245 Pressing force: 60 t Drive power: 4 kW Feed opening: 1195 x 645 mm Feed height: 1114 mm Bale size: approx. 1200 x 1200 x 780 mm Bale weight: 480 kg Tying: manual Theoretical cycle time in idle mode: 25 s Theoretical pressing capacity: 12 cbm/h Dimensions: 1800 x 1253 x 2990 mm (W x D x H) Weight: 2213 kg Materials: film, paper, cardboard Note: The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any possible errors. The offers are subject to change, subject to prior sale and can be revoked at any time. Inspections are possible by arrangement. The sale takes place at our location, without warranty. Our payment terms are 100% prepayment.

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, pressing force: 48 t, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 450 kg, Equipment: documentation/manual, HSM VK 4812 P Year of production: 2017 Fully automatic baler. The device has service and maintenance work by an authorized HSM service with a branch in Germany. Press after significant service work - details after direct contact. The baler comes complete with a ramp for ejection of finished bales and stands for binding wires. Pressing force: 480 kN Drive power: 18 kW Voltage / frequency: 400 V / 50 Hz Capacity at 50 kg/m³: 10.2 t/h Bale width x height x length: 1100 x 750 x 600 - 1200 mm Total length x width x height: 6661 x 3994 x 2583 Machine weight: 10.2 t Compressed material: foil, mixed paper, cardboard, die-cutter waste Bale tying: 4-fold with wire Nledezff Smopfx Aa Ijc We also have other presses in stock. Transport costs depend on weight, volume and, above all, distance, the following information is important for inquiries: Delivery address (postal code and city name), but further details require telephone contact, so please inquire about transport costs and other delivery methods to contact us contact us by phone. Our contact details can be found in the seller's legal information. We sell and export worldwide, and thanks to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-Community invoices - without VAT. opening hours Mon-Fri: 8:00-16:00 Sat: closed