Forging hammer

HUTA ZIGMUNT, Poland MPM 3000

Year of construction: 1987, condition: new, New original spare parts Huta Zigmunt 3 500 … 17 500 kgm. Lhodpolnlmvofx Akysh

Condition: good (used), Magnetic table 455 x 170 mm digital display water tank Lhsdpfxstu Il Ts Akyeh Honing device Wet sanding device

Condition: ready for operation (used), Romanian Forging Hammer CM 2500 (The hammer is similar to Huta Zygmunt MPM 6300B) - Maximum impact energy at full stroke: 7000 kgm - Ram weight: 2500 kg - Mode of operation: pneumatic - Ram stroke: 850 mm - Number of blows per minute: 100 - Working pressure: 5–7 bar - Anvil weight: 48 t - Total weight: 65 t Romanian Forging Hammer CM 1250 (The hammer is similar to Huta Zygmunt MPM 3150B) Lhjdew Sdxaepfx Akysh - Maximum impact energy at full stroke: 3600 kgm - Ram weight: 1250 kg - Mode of operation: pneumatic - Table size (front to back): 700 mm - Stroke: 800 mm - Number of blows per minute: 110 - Working pressure: 5–7 bar - Max. upper die weight: 400 kg - Die height: 220 mm - Ram (front to back): 500 mm - Air consumption: 15 m³/min - Anvil weight: 24 t - Height of machine above floor: 3750 mm - Total machine height: 4380 mm - Total weight: 35 t

Condition: used, Year of construction: 1991, bore capacity in steel (diameter) 50 mm Lsdpfou Sblwjx Akyshh arm length 1100 mm workpiece height max. ca. 1000 mm bore capacity in cast iron 60 mm spindle taper MK 5 spindle turning speed range 28 - 2500 U/min feeds 0,05 - 2 mm/U quill stroke 300 mm distance basic plate - spindle nose 630 - 1380 mm crossrail adjustment vertical 750 mm total power requirement 6 kW weight of the machine ca. 4 t dimensions of machine L x W x H 2,74 x 1,14 x 2,59 mm - with thread cutting attachment - Accessories: box table 550 x 550 x 550 mm, vice, coolant

Condition: used, Year of construction: 1983, Bohrleistung in Stahl (-Ø 50 mm Lhedpfx Akotv Ikleyjh throat 1500 mm workpiece height max. 1380 mm Bohrleistung in Guß (-Ø 60 mm Abstand Spindelmitte bis Säule 320 - 1250 mm swival range +/- 180 ° base plate surface area 2640 x 1000 mm max. torque on the spindle 310 Nm Bohrspindel-Ø/ Aufnahme 75 mm /MK 5 bore spindle stroke 310 mm spindle turning speed range 28 - 2500 U/min feed: 0,05 - 2 mm/U power capacity 4 kW weight of the machine ca. 4,3 t dimensions of the machine ca. 3,2 x 1 x 2,75 m cube table 500 x 500 x 500 mm

Condition: excellent (used), 1. Permanent-magnet chuck, D = 315 mm, with mounting flange according to DIN 55027, size 6. Lhsdpfx Akod Eaausyoh

Condition: used, BROACHING MACHINE Lhsdpfxst Hr Dfj Akysh

Condition: good (used), Year of construction: 1971, functionality: fully functional, machine/vehicle number: 12.02-37-31, grinding wheel width: 250 mm, grinding wheel diameter: 500 mm, grinding diameter: 125 mm, grinding length: 200 mm, type of input current: three-phase, overall weight: 5,000 kg, workpiece diameter (max.): 125 mm, nominal power: 28 kW (38.07 HP), The machine was used exclusively for grinding piston rods with a diameter of 10 mm. Lhsdpfx Aksw E D Eujysh

Condition: excellent (used), Year of construction: 2012, bore capacity in steel (diameter) 62 mm arm length 350-1600 mm workpiece height max. 1250 mm distance spindle nose and table 350-1250 mm Boring depth max. 315 mm machine table 2400 x 1000 x 200 mm Turning speeds of the bor. spindle 38 - 2000 U / min Lhsdpfeyhq T Nsx Akyjh spindle taper MT5 feed 0,06 - 1,00 mm/U engine output 4 kW stroke drive 1,5 kW oil pump 0,75 kW total power requirement 6 kW weight of the machine ca. 3,8 t dimensions of the machine ca. 2490 x 1050 x 2780 mm Steps of spindle speed: step-less Steps of spindle feed: 8 Speed of the arm up and down: 1.2 m/min Arm moving angle: ±180 degree Spindle moving distance of each dial revolution: 122 mm Max. spindle torque: 400 Nm Max. spindle feed resistance: 16000 N

Condition: used, Year of construction: 1964, Technical details: shaft diameter: max. 120 mm work piece - max.: 800 mm height of profile: Tiefe: max. 90 mm grinding spindle speed: nicht bekannt U/min Table dimensions: Ø 150 mm voltage: 380 V total power requirement: 1,1 kW weight of the machine ca.: 0,675 t dimension machine xH: 0,75 x 0,70 x 2,0 m Application: vertical internal cylindrical grinding of shafts face, and center grinding with shaft grinder. Spindle head technical details: -equipment shank grinder Ø 13mm 60°; clamping element Ø 6mm shank clamping head. -travel=vertical 950mm by handwheel and transversal 80mm by crank handle -abrasive device with diamond, adjustment crosswise= 80mm. Table other specifications: -with fixed tip holder 60°. Lhedeu Ngr Dopfx Akyjh -speed 63 / 125 rpm. -adjustment vertical 600mm, in height 1.100mm, operation manual. centering block: -prismatic guide accessories: -fixed tip L=180mm -fixed tip L=300mm -div. shank grinder -div. clamping and auxiliary tools *