Working platform semitrailer

KÖGEL Multi Chassis, verstärkt, Bordwände

Condition: used, maximum load weight: 36,040 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 05/2025, next inspection (TÜV): 05/2027, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment. Complete equipment available upon request. Hodpfxszc A Afe Anpjp Chassis * Regular ladder frame in lightweight steel with continuous crossmembers * With an extension of the chassis frame, the coupling plate is approximately 8 mm thick * with a 2-inch kingpin according to DIN 74080 / ISO 337 Suspension * Axle lift mechanism on axle 1 * Three-axle unit SAF INTRADISC * with disc brakes Ø 430 mm * ET 120 air suspension with approximately 180 mm travel Tires * Wheels with internal sensors according to UN ECE R141 * 6x 385/65 R 22.5 UNIROYAL TH 50 * 6 steel rims 22.5 x 11.75 * Offset approximately 120 mm (ET 120) Chassis components * Mechanical fifth wheel with leveling foot, approximately 24 t lifting capacity, single-sided operation on the right-hand side while driving * Storage box for: 10 side panels, folding stakes, and rear gate, fully enclosed, protected against spray water, also serves as a side protection device * 2 plastic toolboxes, waterproof, dimensions (internal) approximately 545 x 400 x 400 mm, installed at the rear, 1x on the left and 1x on the right Brake / Air suspension system * EBS system 2S/2M with stability program (includes ABS/ALB function) * EBS plug connection ISO 7638 (without connection lines) * Parking brake as a spring brake, external pneumatic connections as well as an external EBS diagnostic connection via ISO 7638 plug connection * WABCO EBS system * Air suspension system including 1 lifting and lowering valve, mounted on the left-hand side behind the axle unit while driving, driving position is set automatically * 2 non-interchangeable coupling heads at the front ISO 1728 * Air tanks for the brake system and air reservoir made of steel (EN 286-2) Floor * Flat floor approximately 30 mm thick, multiply laminated plywood * Floor sealed around the perimeter * Stake pockets for square tube inserts approximately 80 x 80 mm * Storage for a maximum of 14 square tube inserts approximately 80 x 80 (length 1,990 mm) on the front wall inside Front wall * Front wall approximately 2,000 mm high with steel corner posts, with profiled steel sheet, screwed/riveted to the frame * 2 pairs of lashing points (permissible lashing force approximately 1,000 kg per ring) on the front wall according to EN 12640, Note: If the front wall is used for securing the load, suitable lashing straps must be used to tighten the load, if the vehicle is operated without side panels and a rear gate Rear wall * Folding rear wall approximately 600 mm made of aluminum hollow profiles with 3 tension bars and T-handle locks * 2 folding steps on the inside, folding steel corner posts at the rear in the height of the side panels Side wall * 4 pairs of folding stakes in the height of the side panels * VarioFix steel hole outer frame * 4 pairs of stake holders for folding stakes on the outer frame (evenly distributed) * 24 pairs of lashing eyes in the outer frame (according to EN 12640), permissible tensile force approximately 5,000 kg per ring Side panels * 5 pairs of folding side panels approximately 600 mm made of aluminum hollow profiles with tension bars Electrical / Electronics * Lamp carrier made of steel, arranged above the underrun protection * KÖGEL LUXIMA Premium package, consisting of: LED license plate lighting, LED outline lights and reflectors at the front, flashing LED side marker lights, Superseal and bayon