Swap body semitrailer

Abrollcontainer Container 6,5 m Kran Fassi F150

Condition: new, loading space length: 5,300 mm, loading space width: 2,420 mm, total length: 6,500 mm, Year of construction: 2026, Brand new roll-off container with FASSI loading crane Roll-off container in a platform design with aluminum sideboards and a permanently mounted Fassi loading crane ELLERMANN roll-off container according to DIN 30722-1 with aluminum sideboards and crane platform Platform tipper body type K 33 s Internal dimensions: approx. 6.5/5.3 x 2.42 x 1.0 meters, all dimensions are approximate Useful volume: approx. 13 m³ Paint finish: in RAL color according to customer's request ? Mounting brackets for hook lift systems according to DIN 30722-1 (15,000 kg) with rear outside rollers and subframe made of INP 180 Outside rollers are greaseable and replaceable Mounting bracket Ø 50 mm, hook height 1,570 mm Transition from the subframe to the end wall support reinforced with 10 mm gusset plates ? Crane platform 20 mm thick at the end, length approx. 1,200 mm Reinforcement on the end wall support and subframe inside Additional stiffening on the end support ? End wall inner height approx. 1,000 mm ? Floor made of 5 mm St 37.2 (S235JR) ? Floor spar spacing 500 mm Spar profile U 80 x 50 mm ? Outer profile as a hole strip (a hole Ø 40 mm every 200 mm), Loadable with 500 kg / hole, max 5 tons per side, operable from the inside ? Aluminum sideboards, approx. 1.0 meter high, foldable and removable, 1 x divided in the middle by a removable center post ? Aluminum rear flap, foldable and removable (cannot be driven over) with removable corner posts ? All-around tarpaulin and net hooks ? Container double primed inside and out and double painted in a single color inside and out ? Aluminum sideboards unpainted ? UVV stickers with safety instructions ? Container tested and approved according to DGUV rule 214-017 (formerly BGR 186) ? Container test book (digitized) for documentation of the required annual recurring inspection according to UVV FASSI loading crane F150A.2 e-dynamic Design according to CE directive (EN 12999) The equipment manufacturer must carry out the inspection once the loading crane has been mounted in its final position and is ready for operation. Base unit: F150A.2 e-dynamic Slewing range 416° All hydraulic cylinders are double-acting Piston rods are hard chrome-plated Double lever system with PROLINK (overextension of the knuckle arm up to 15°) Electronic overload protection device with FX500 6 functions RCH or RCS radio remote control (linear levers) with Display and XP system Emergency stop, as well as optical alarm (90% and 100%) Including digitally adjustable slewing limit FASSI stability control FSC including LMB II Pressure relief and load holding valves, high-pressure filter Danfoss S800 control block with 4 control valves, operable from one side Separate hydraulic tank (90 l) with filter, mounted on the crane base Extendable on both sides, support width 4.60 m, hydraulic support - CE, including M.O.L. Standard color RAL 3020 traffic red - all cylinders painted black Load hook and attachment bridges (short / 500 mm) Driving position: folded transversely to the direction of travel Dead point above the support beam Caution: Note the on-board voltage / 12 V or 24 V, standard 24 V Bedpfx Apezq Iu Iohodf F150A.2.23 e-dynamic » Base unit IE742 connection box Support spread to support width 5.4 m Move dead point 1 LED work light on the knuckle arm » mounted LED for 2 outriggers, not mounted » (crane) Control system for 2 additional functions with » 2 hose guides / eactive Slewing valve, only for cranes with rack and pinion Quick-release valve for the extensions E