MANURHIN K'MX 620

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: M01.16.21.51.02, travel distance X-axis: 1,600 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 500 mm, spindle speed (max.): 10,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range X-axis: 1,600 mm Travel range Y-axis: 1,200 mm Travel range Z-axis: 500 mm Travel range W-axis: 1,200 mm Travel range B-axis: 360° Spindle speed: 10,000 rpm Spindle motor power: 30 kW Feed drive: Brushless AC servo motors Feed rate: 0–20,000 mm/min Rapid traverse X-axis: 20,000 mm/min Rapid traverse Y and Z axes: 20,000 mm/min Manual mode: 20,000 mm/min Setup operation: 0–2,000 mm/min Table size: 1,500 × 1,500 mm T-slots: 5 × DIN 650-22 H12 Bedsznkpvspfx Ablswr T-slot spacing: 150 mm MACHINE DETAILS Tool clamping: Hydraulic Electrical connection: 400 V Frequency: 50 Hz Compressed air operating pressure: 6 bar Nominal flow rate: 7,000 rpm

Condition: refurbished (used), functionality: fully functional, Löser centerless tube grinding machine - belt grinding machine - polishing machine - Cylindrical grinding machine Centerless tube grinding / polishing machine for workpieces with a minimum length of 1100mm. The machine was built in 1988 and was completely overhauled in 2012. The machine was converted for polishing and then only polished around 10,000 parts. The machine was no longer used after that. During the general overhaul, the motors, bearings and the entire control cabinet with the frequency converters were completely replaced. The machine can be used for both wet grinding and polishing. Wastewater treatment including pumps is not yet available. We can retrofit these for you according to customer requirements. The transport systems (roller conveyors) between the grinding stations must also be retrofitted to suit your workpieces. The machine can process pipe diameters from 10mm to 160mm. The grinding motors / polishing motors have an output of 7,5kW per station. Bedpfxotmqi Do Ablewr The system can be viewed by appointment in our warehouse in D-63128 Dietzenbach.

Year of construction: 2007, condition: ready for operation (used), functionality: fully functional, travel distance X-axis: 3,500 mm, travel distance Y-axis: 280 mm, travel distance Z-axis: 300 mm, spindle speed (max.): 21,000 rpm, working length: 3,750 mm, TECHNICAL DETAILS Machining length with bar support: 3,750 mm Machining length without bar support: 3,500 mm Travel range X-axis: 3,500 mm Travel range Y-axis: 280 mm Travel range Z-axis: 300 mm Positioning speed: 30 m/min Positioning accuracy: ±0.1 mm Spindle power: 6 kW Spindle speed: 21,000 rpm Spindle interface: HSK F63 Bedpoznczkofx Ablowr Tool positions: 5 Max. tool diameter (manual): 200 mm Max. tool diameter (automatic): 92 mm Max. saw blade diameter: 500 mm MACHINE DETAILS Air consumption: approx. 50 l/cycle Compressed air requirement: > 7 bar Power supply: 400 V, 3-phase Note: The machine's operating hour counter is defective and cannot be read. The machine was only used in a single-shift operation.

Condition: ready for operation (used), Year of construction: 1995, functionality: fully functional, travel distance X-axis: 3,000 mm, travel distance Y-axis: 420 mm, travel distance Z-axis: 480 mm, controller model: Heidenhain TNC 407, rotational speed (max.): 6,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Bjdpfxozncnqo Ablewr Travel range X-axis: 3,000 mm Travel range Y-axis: 420 mm Travel range Z-axis: 480 mm Table size: approx. 3,000 × 500 mm Spindle connection: SK40 Maximum speed: 6,000 rpm Tool changer: 22-position MACHINE DETAILS CNC control: Heidenhain TNC 407 EQUIPMENT Additional angular/universal milling head Coolant system Documentation/manual 4/5-axis machining: possible Machining of complex workpieces: possible

Year of construction: 2004, condition: excellent (used), Swiss type lathes MANURHIN K'MX overhauled with : – Spindle, counter spindle, geometry and changes of all non-conforming parts. Rotating tool on: rear comb, front comb, end unit, radial and axial counter operation C-axis on: main spindle and counter spindle Rigid tapping on: main spindle and backworking spindle High-pressure Predispo Year of construction 2004 – approx. 22 000 h Bwedeir Id Uepfx Abljr

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, travel distance X-axis: 800 mm, travel distance Y-axis: 800 mm, travel distance Z-axis: 800 mm, controller model: Siemens 840D, spindle speed (max.): 12,500 rpm, TECHNICAL DETAILS Bodozncnkopfx Ablswr Travel range, X-axis: 800 mm Travel range, Y-axis: 800 mm Travel range, Z-axis: 800 mm Spindle speed: 12,500 rpm Number of axes: 4 Pallet size: 630 × 630 mm Max. tool length: 600 mm MACHINE DETAILS Control system: Siemens 840D

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, travel distance X-axis: 1,000 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 1,100 mm, controller model: Siemens 840D, spindle speed (max.): 8,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 1,000 mm Travel range, Y-axis: 1,200 mm Travel range, Z-axis: 1,100 mm Spindle speed: 8,000 rpm Pallet size: 630 × 630 mm Rotary table: 360,000 × 0.001° Tool positions: 400 Tool interface: HSK 100 Number of machining axes: 5 MACHINE DETAILS Bedpfx Abjzncndjlowr Control system: Siemens 840D

Condition: new, Year of construction: 2023, The K’MX 920 CLEVER sliding headstock automatic lathe is designed for machining complex workpieces up to Ø 20 mm. The lathe is equipped as standard with two electrospindles with a maximum speed of 12.000 rpm each. With its nine axes, comb + turret on three axes and independent end unit, this machine is capable of having four tools in the material for an optimised cycle time. Bjdpfjk Dz Diox Ablswr 9 linear axis 1 independent rack with 10 positions Cross-section of outer tools 12 x 12 mm Turret number of stations 12

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2016, operating hours: 27,875 h, machine/vehicle number: 150204, laser type: CO₂ laser, laser wavelength: 10 nm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Laser type: CO₂ laser Average power: 200–5,000 W Peak power: up to 6 kW Wavelength: 10.6 µm Beam quality factor M²: < 2.4 (typically 2.1–2.3) Beam divergence: 1.5 mrad (half-angle) Bodpfx Aezncm Hjbljwr Beam diameter at the output: 15 mm (1/e) Beam diameter at the output: 21 mm (full beam) Pulse repetition rate: 0–2 kHz Pulse width: 250 µs Pulse resolution: 70 µs (?) Alignment stability: ± 150 µrad (?) Wavelength: 635 nm Output power: < 1 mW MACHINE DETAILS Ambient temperature: 10–40 °C Relative humidity: < 95% (non-condensing) Connected power: 37 kW Voltage: 400–460 V AC Voltage tolerance: ± 10 % Power connection: 3-phase Required cooling capacity: 45 kW Flow rate: 133 l/min Inlet temperature: 18–20 °C Maximum inlet pressure: 6 bar Nominal inlet pressure: 3 bar Differential pressure: 1.5 bar Cooling medium: Distilled water with 35 % Dowfrost HD Filter fineness: 100 µm Helium purity: 99.996 % Helium proportion: 67.7 % Helium consumption: 13.4–46.8 SLPH Carbon monoxide purity: 99.995 % Carbon monoxide proportion: 4.1 % Carbon monoxide consumption: 0.9–3.0 SLPH Nitrogen purity: 99.996 % Nitrogen proportion: 28.2 % Nitrogen consumption: 5.8–20.2 SLPH Total gas consumption: 20–70 SLPH Maximum proportion of water vapor, hydrocarbons, and oxygen: < 10 ppm Compressed air: dry Compressed air dew point: < 2 °C Operating hours (according to meter): 27,875 h

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 42.503, clamping force: 4,000 kN, screw diameter: 70 mm, injection pressure: 1,481 bar, injection weight: 1,040 g, overall weight: 5,600 kg, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Clamping force: 4,000 kN Platen size: 1,300 × 1,080 mm Minimum tool height: 350 mm Maximum opening stroke: 1,300 mm Screw diameter: 70 mm Injection volume: 1,155 cm³ Injection weight: 1,040 g Injection pressure: 1,481 bar Bodjzncmtjpfx Ablswr MACHINE DETAILS Electro-hydraulic system Rated power of pump motor: 45 kW Dimensions & Weight Dimensions (L × W × H): approx. 8,000 × 2,250 × 2,200 mm Weight: approx. 5,600 kg

Condition: used, Year of construction: 1990, Technical details: spindle passage: 23 mm z-axis: 150 mm turning length: 150 mm stroke: x+z Achse / Axis/eje/eixo/os = 30 mm facing movement (x-axis): 30 mm longitudinal traverse (z-axis): 30 mm control: Num 760T spindle turning speed - continuous: U/min feed speed: x/y: 5 mm/min feed speed: z: 10 mm/min tool turret: 2 Stück/pcs mit je/each 6 tools operating pressure: max. 45 bar total power requirement: 8,0 kW weight of the machine ca.: 2,2 t dimension machine xH: 2,45x1,3x2,2 m dimensions of the bar loader L-W-H: 4,65x0,5x1,3 m techn. details: Bwedou Iwyvspfx Abler - bar clamping hydraulic -automatic workpiece discharge (via catch basket) - 2 turrets with each 6 tool tapers - coolant device - control NUM 760 (size: L:1,0xW0,8mxH:1,56m) Zubehör: - bar loader magazine make IEMCA type CS 112/31 accessories: -24 div. tool tapers - device tool Sylvac system ( size:L:0,58xW:0,5xH:0,43m) *

Condition: ready for operation (used), Year of construction: 2015, machine/vehicle number: 417/1-505, functionality: fully functional, operating hours: 29,856 h, cutting height (max.): 80 mm, cutting width (max.): 3,100 mm, saw blade diameter: 350 mm, cutting length (max.): 4,200 mm, Equipment: scorer, The machine is still in operation and will be available starting October 9, 2026! Bwsdpfx Aoznbkkobler TECHNICAL DETAILS Cutting length: 4,200 mm Cutting width (program slider travel): 3,100 mm Cutting height: 80 mm Saw blade overhang: 85 mm Min. clamping width: 0 mm Max. clamping width: 1,300 mm Saw units Main saw motor: 11 kW Main saw blade diameter: 350 mm Scoring saw motor: 1.5 kW Scoring saw blade diameter: 180 mm Motorized groove cutting device: 0–35 mm MACHINE DETAILS Software: Opti-Cut Display: 17″ TFT Control system: Opti-Cut Electrical data Operating voltage: 400 V (+10 % / -5 %) Mains frequency: 50 Hz Electrical connection rating: 20 kW Total weight: 6,200 kg Operating hours: 29,856 h EQUIPMENT Angle stop on the left 7 roller rails 8 clamping devices Clamping device opening: 82 mm First clamping device with double finger 4 air cushion tables 1 central blower Labeling package including label printer Opti-Cut software installed Printing and clamping system Cutting height automation Pressure beam height control Angle and backstop device

Condition: ready for operation (used), Year of construction: 2002, machine/vehicle number: 0-250-08-1590, functionality: fully functional, travel distance X-axis: 3,250 mm, travel distance Y-axis: 1,220 mm, travel distance Z-axis: 125 mm, controller model: Homatic 2000 IPC, number of spindles: 28, spindle speed (max.): 24,000 rpm, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Working area X-axis: 200 – 3,250 mm Working area Y-axis: 70 – 1,220 mm Working area Z-axis: 12 – 125 mm (clearance 150 mm) Tool changer positions: 18 Spindles Total number of drilling spindles: 28 Vertical drilling spindles: 22 Horizontal drilling spindles in X-axis: 4 Horizontal drilling spindles in Y-axis: 2 Milling spindle power: 12 kW Bwsdjznbgrjpfx Ablsr Milling spindle max. speed: 24,000 rpm C-axis: 360° interpolation MACHINE DETAILS Vacuum pump capacity: 100 m³/h Control model: Homatic 2000 IPC Control software: WoodWop 4.5 incl. MDE and production list software FEATURES 4 axes Console table 8 manually adjustable supports in X direction 3 vacuum cups per console Vacuum connection for templates Laser positioning aid for vacuum cups Laser projection for cup positioning Liquid circulation cooling Operator terminal Note: The sale does not include the pictured adapter units, tools, or HSK holders.

Condition: used, Year of construction: 2001, Technical details: turning diameter: 33 mm turning length: 330 mm control: 840 total power requirement: 20 kW Bodpfxjw D Hh Aj Ablswr weight of the machine ca.: 6 t dimensions of the machine ca.: 3850,2000,2100 m 17 axes 3 revolvers with the powered tools 1 gantry with the driven tools Main and counter spindle with C axes Barfeeder Machine On-time 58,133 hours *

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2025, operating hours: 1 h, load capacity: 5,000 kg, lifting height: 4,700 mm, fuel type: diesel, construction height: 2,480 mm, Equipment: all wheel drive, No minimum price – guaranteed sale to the highest bidder! Bwedpfoznagkox Ablor Equipment with only 1 operating hour! TECHNICAL DETAILS Load capacity: 5,000 kg Lifting height: 4,700 mm Overall height: 2,480 mm MACHINE DETAILS Drive type: Diesel Front tires: Pneumatic tires Rear tires: Pneumatic tires Operating hours: 1 h EQUIPMENT All-wheel drive External reference: HEL0329TR004