Used Marel Townsend Moulding Machine for sale (66,856)

Condition: ready for operation (used), Year of construction: 2011, Marel 2630 Salmon Filleting Machine If you’re processing salmon or trout, the Carnitech CT 2630 will give you a competitive advantage. The dual knife system – band and circular – ensures a clean, precise cut every time. This results in a higher yield, less waste, and a better-quality fillet. It’s designed to handle fish ranging from 2 to 7 kg, processing up to 20 fish per minute without compromising cut quality. The integrated compressor and low water usage make it efficient and hygienic. Add the circular knife grinder accessory to maintain optimal performance. This machine is all about fast, clean, and consistent output. Unique cutting principle Combination of circular knives and band knives Significantly improved yield Electrical panel and compressor with dryer are fully integrated Easy access for cleaning Manufacturer: Marel Model: CT 2630 Year: 2011 Fish size: 2-7 kg Capacity: Up to 20 fish/minute Hedpjzu Rfkjfx Akronu Electricity: 3x400V Power consumption: 4.0 kW Machine dimensions L x W x H: 2,000 x 850 x 1,650 mm Machine weight: 675 kg

Condition: good (used), Year of construction: 2001, Ref. no.: 18092 Manufacturer: ENGEL Type: ES 1350H 200W / 300HL-2F Year of construction: 2001 Clamping unit Clamping force: 300 ton Opening stroke: 855 mm Platen size (h x v): 1050 x 650 mm Injection unit Screw diameter: 60 +35 mm Injection volume: 735 +135 cm³ Shot weight: 662 + 122 g Injection pressure: 1834 +1620 bar Hnodewm Iy Eepfx Akrsu Measurements and weight Dimensions: 7,75 x 2,35 x 2,6 m Machine weight: 24780 kg Further information: ENGEL ES 1350H200W/300HL-2F — 2K Injection Moulding Machine This machine from the prestigious Austrian manufacturer ENGEL, built in 2001, features a clamping force of 300 tonnes and a true 2K L-configuration in horizontal layout. Motor and Hydraulic System The machine is equipped with a powerful electric motor coupled to a high-pressure hydraulic pump group. The electric motor continuously drives the hydraulic pump, providing pressurised oil flow throughout the entire system. This pressurised oil feeds the clamping cylinder, the injection pistons of both units, and the ejector system. The thick red hydraulic hoses visible behind Unit B carry this high-pressure oil flow — both units are supplied via independent hydraulic circuits, allowing Unit A and Unit B to operate simultaneously without influencing each other. Operating Principle The two independent injection units are positioned at 90° to each other — in an L-shape. The mould is locked with 300 tonnes of clamping force. Unit A injects the primary material into the mould at 1834 bar. Immediately afterwards, Unit B injects the second material or colour from a 90° angle into the same mould at 1620 bar. The two materials bond at a molecular level inside the mould, cooling is completed and the ejectors push out the finished 2K part as a single piece. No gluing, screwing or assembly is required — two materials emerge as one single part in a single cycle. Applications Automotive interior and exterior trim parts, large technical plastic components, parts combining a rigid body with a soft grip surface, two-colour large-surface parts.

Year of construction: 1994, condition: used, There are three Arburg ALLROUNDER 370C 800-225 available, an on-site inspection is possible. Hnedpfx Aoz Sr Ruskrsu

Condition: ready for operation (used), Year of construction: 1970, operating hours: 1,362 h, functionality: fully functional, machine/vehicle number: 9286, planing width: 600 mm, Planer machine Kupfermühle 5 spindles: bottom / top / right and left / bottom We have produced castle floorboards with this machine, and it was operational until the end. The machine can be demonstrated. Hnsdpfx Ajyyvuwekrju Due to its age, it is sold without warranty or guarantee.

Condition: good (used), Year of construction: 2004, Ref. no.: 18255 Manufacturer: ENGEL Type: Victory 750 / 180 tech Year of construction: 2004 Clamping unit Clamping force: 180 ton Opening stroke: 750 mm Distance between tie bars: 960 x830 mm Mould height min.: 500 mm Opening width: 1250 mm Injection unit Screw diameter: 45 mm Injection volume: 318 cm³ Shot weight: 302 g Injection pressure: 1769/2360 bar Measurements and weight Machine weight: 13500 kg Robot Producer: Wittman Type: W743 Year: 2009 Further information: ENGEL Victory 750/180 Tech – Power, Flexibility and Reliability with Tie-Bar-Less Technology The ENGEL Victory series was specially developed for technical plastic processing and is known as a professional injection moulding machine series offering high energy efficiency and maximum mould flexibility. Unlike conventional tie-bar machines, this series provides a much more flexible working area thanks to its tie-bar-less clamping system. ⸻ 🔍 Advantages of the ENGEL Victory Series ✔ Tie-Bar-Less Design The biggest advantage of the world-renowned ENGEL Victory series is its tie-bar-less construction. This system offers several important advantages: • Larger moulds can be installed easily • Easier access for complex mould geometries • Reduced mould changeover times • Easier robot integration • More efficient use of production space This technology is especially advantageous for automotive, technical plastic parts, packaging and industrial applications. ⸻ ✔ Wittmann Robot Integration The machine has been operated together with a Wittmann robot. Robot specifications: • Wittmann W743-0424 • Year of manufacture: 2009 • Payload capacity: 25 kg • X-axis: 1200 mm • Y-axis: 1600 mm • Z-axis: 4000 mm This configuration provides major advantages for automated production processes. ⸻ Hnodpfswm Iz Nex Akrou 🔍 Machine Operating System The ENGEL Victory Tech series operates with a servo-hydraulic system. ✔ Hydraulic System: • Clamping unit • Injection movements • Ejector system • Mould movements are driven by a high-performance hydraulic system. ✔ Thanks to the servo-controlled hydraulic system: • Only the required amount of energy is consumed • Power consumption is significantly reduced • Quieter operation is achieved • Production stability is improved Unlike older conventional hydraulic machines, the machine does not run continuously at full power. The servo pump system operates only when needed, providing the following advantages: • Lower energy costs • Reduced heat generation • Longer component lifetime • More stable processing conditions

Condition: good (used), Year of construction: 2003, functionality: fully functional, planing width: 230 mm, working height: 100 mm, Planer Moulder P 1000 UNIMAT STAR with 6 Tool Holders Hedpfxexyu Ite Akronu

Condition: used, mobile Hjdpfxsz Ry Sdo Akrsnu dimensions (l x w x h) : ± 900 x 900 x 1.600 mm Autonomous operation (can be connected to almost all types of pre-duster)

Condition: used, Marvel Townsend StorkDMM50 meat bone separator to produce best quality low pressure deboned meat when used in conjunction with a Baader or SEPAmatic. This machine has come direct from a closed meat factory in Scotland. Almost impossible to find these machines on the used market. Hnedslkc I Repfx Akrju

Year of construction: 2018, condition: used, Clamping force: 900kN, screw diameter: 30mm, L/D ratio: 22, specific injection pressure: 1540bar, calculated shot volume: 88.4cm³, max. shot weight (PS): 80.4g, tie-bar spacing (H×V): 470mm/420mm, min. mold height: 225mm, max. platen distance: 700mm, opening stroke: 475mm, ejector stroke: 150mm, ejector force: 41.2kN, control system: UNILOG B8, weight: 4200kg. Documentation available. An on-site inspection is possible. Hjdpfx Akez Hn Sporonu

Condition: good (used), Code: 0234 Brand: SPANEVELLO - ITALY Model: SC 17 Automatic 7-spindle moulding machine for window frames, frames, profiles, joinery, carpentry, wooden packaging and various Technical data: Sturdy structure with electro-welded steel base Working width 170 mm Working height 120 mm Variable feed speed 5/25 mt/min Automatic lifting of upper beam Composition: 1° spindle: Surface planer - Motor Hp 4 2° spindle: Right vertical spindle moulder - Motor Hp 4 3° spindle: Left vertical spindle moulder - Motor Hp 4 4° spindle: Right vertical spindle moulder - Motor Hp 4 Hnjdpfx Akoxukgujreu 5° spindle: Thickness planer - Motor Hp 7,5 6° spindle: Right vertical spindle moulder - Motor Hp 4 7° Universal spindle 180° - Motor Hp 8,5 Diameter of shafts of working heads mm 40 Shaft rotations of working heads 6000 rpm Power of feed motor Hp 2 Suction inlet diameter 150 mm Overall dimensions mm 4800 x 1650 x 1450 h Weight kg 3000

Condition: used, Year of construction: 2005, Cuts fillets into portions by weight The Marel IPM3 X300 is a portion cutter for fish, chicken and meat fillets. Each piece is scanned on the belt, and the machine works out where to cut to get portions of a fixed weight or length. You get more out of every fillet with less trim left over. The machine was built in 2005 and has a perforated belt 280 mm wide. Settings are made on the control panel with a colour screen. Located in Emmeloord, the Netherlands. Immediately available, price on request. More photos and full specifications: / Type: Portion cutter (fixed weight or fixed length) Hsdsz Nc Rrjpfx Akrjnu Products: Fish, chicken and meat fillets Belt: Perforated, 280 mm wide Scanner: Cameras with laser line Controls: Control panel with colour screen Electrical: 3 x 380–480 V Construction: Stainless steel

Condition: excellent (used), For sale: Guilliet KXK four-sided planing machine Very well-maintained, from a one-man carpentry shop Year of manufacture: 1995 Max. planing width: 180mm Max. planing height: 120mm Length of feed table: 2100mm Hnsdjzivf Sjpfx Akrsu Tool diameter: 100mm Motor powers: Surfacing cutter: 3.7 KW Right cutter: 3.7 KW Left cutter: 3.7 KW Thicknessing cutter: 3.7 KW Feed motor: 1.0 KW Motor power for height adjustment: 0.37 KW Motorized adjustment of the feed bar with the thicknessing cutter Dust extraction connections: Surfacing and thicknessing: each 160mm Left and right cutters: each 120mm

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Hnodpfog Ailcox Akreu Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: good (used), Year of construction: 1994, Ref. no.: 17540 Manufacturer: ARBURG Type: 270 C 500-100 RUNHOUR Only 100 Year of construction: 1994 Clamping unit Clamping force: 50 ton Opening stroke: 350 mm Distance between tie bars: 270 X 270 mm Mould height min.: 200 mm Platen size (h x v): 405 X405 mm Injection unit Screw diameter: 25 mm Injection volume: 67 cm³ Shot weight: 61 g Injection pressure: 2500 bar Measurements and weight Dimensions: 3,3 X 1,5 X 2,0 m Machine weight: 2400 kg Further information: Laboratory Machine with Exceptionally Low Operating Hours Hnjdpfoyiz U Tsx Akrsu The offered ARBURG 270 C 500-100 was manufactured in 1994 and originates from the training and laboratory department of a university. The machine was not used in regular production and was mainly operated for educational and testing purposes. The control system shows only approximately 100 operating hours and just 867 machine cycles. The machine is equipped with a hydraulic drive system and the proven ARBURG Dialogica control unit. In addition, it features an integrated crane system to facilitate mould and component changes. The scope of supply also includes an unused spare screw with a diameter of 15 mm and a complete additional plasticizing unit, providing extra flexibility for different applications. Due to its exceptionally low usage, documented history, and valuable additional equipment, this machine represents a rare opportunity on the used machinery market.

Condition: new, Year of construction: 2005, Planing machine with infeed device EM 11 with 5th spindle at the bottom Hnjdpezvvuajfx Akrsu Includes 5 planing heads.

Year of construction: 1998, condition: used, There are five Arburg ALLROUNDER 270C 300-80 available, year of manufacture: 1x 1998, 2x 1997, 2x 1994, an on-site inspection is possible. Hsdpfx Asz Sr Rhskrsnu

Condition: used, Year of construction: 2016, operating hours: 26,000 h, clamping force: 850 kN, displacement volume: 679 cm³, injection pressure: 2,000 bar, overall weight: 55,000 kg, screw conveyor diameter: 95 mm, terms of delivery: EXW (ex Works) delivery time: on request Hnsdpfx Aksz S N Rforou terms of payment: 100% prior to delivery

Condition: excellent (used), Year of construction: 2003, operating hours: 21,200 h, functionality: fully functional, machine/vehicle number: 190332, Equipment: documentation/manual, Injection molding machine 3 colors (horizontal /vertical/ and 3. in L-position with protective housing) The machine can be used as a 2 colour/2K machine and the 3rd can be deactivate immediately available from our warehouse in Hannover Make: Arburg Type: 420C 1000-150/150/60 year of construction 2003 Control: Selogica Hours: 21200 h without turntable +++++clamping unit +++++ Clamping force: 1000 kN / 1000 to. tie bar distance: 420 x 420 mm Hedpfx Akegrzh Eorjnu platen size: 795 x795 mm tool height 300 mm distance platens max. 950 mm ejector 225 mm /66 kN ++++Injection unit 1 (150 unit) ++++ Screw size: 15 mm (high shut-off fixed) Injection volume: 17 ccm Injection weight: 15 gr. Injection pressure: 2750 bar ++++Injection unit 2 (150cc unit) ++++ Screw size: 15 mm (highly screwed fixed) Injection volume: 17 ccm Injection weight: 15 gr. Injection pressure: 2750 bar ++++Injection unit 3 (60cc unit) ++++ Screw size: 15 mm (highly screwed fixed) Injection volume: 17 ccm Injection weight: 15 gr. Injection pressure: 2080 bar Extras 2x core pull 1 ALLROUNDER 420 C 1000 - 150 / 150 / 60 fully hydraulic screw injection molding machine mold clamping force 1000 kN voltage 400 V / 50 Hz 1 Vertical injection unit instead of clamping tie bars mounted on carriers for 2nd injection unit, manually operated, working position adjustable between 70 and 250 mm VE-404/02 1 Open nozzle 15 mm low-wear, without heating tape (1.SPE 150) VE-902/00 1 Technology level 2 - servo-controlled Hydraulic system -two control pumps for controlled machine movements, path-dependent, controlled target ramps. The build-up of the tool clamping force programmable + controlled. Clamping force is servo-controlled via second pump. The nozzle contact force programmable. The contact force can be set manually, the value is maintained in a controlled manner. This technology level is a prerequisite for simultaneous movements of the nozzle, ejector and optional core pullers. Including equipment package for "extended travel movements". VE-132/03 1 Technology level 3 Hydraulic system with 3 control pumps for simultaneous movements of the main axes and for faster movements of the secondary axes. For the 2-K machines as hydraulic system for the 2nd injection unit (prerequisite is technology level 2, VE 132/03) VE-130/40 1 heating tape for open nozzle VE-320/00 1 Injection unit 150 for vertical injection into mold partition for 2-component processing VE-136/02 1 position controlled screw with control valve at the injection unit, incl. controlled back pressure, nozzle contact force manually adjustable VE-561/20 1 position-controlled screw with control valve for multi-component machines, incl. controlled back pressure, nozzle contact force manually adjustable - for injection unit 2 VE-561/30 1 injection unit 60 for horizontal injection into mold partition as 3rd injection unit for multi-component processing (L-position) VE-906/00 1 for VE 906/00 injection unit 60 in L-position: unit lowered by 70 mm, incl. special parting line full protection VE-907/00 1 Plasticizing barrel set 15 mm (without nozzle), with advanced feed and pressure reducing valve, in highly wear resistant design 1 Open nozzle 15 mm wear-resistant, without heating band (L-position) VE-909/00 1 Nozzle tip with radius 15 (L-position) VE-910/00 1 Heating tape for open nozzle (L-position) VE-911/00 1 Position-controlled screw for the third injection

Condition: used, Wittmann Battenfeld 3 Vertical V 800/315 injection molding machines Hodpfx Aozpwrgskrsnu for thermoplastics Type: Vertical V 800/315 Design: Vertical Control system: Battenfeld UNILOG B4 Clamping force: 800 kN Injection unit: 315 Screw diameter: 40 mm Calculated displacement volume: 201 cm³ Maximum shot weight: approx. 183 g Specific injection pressure: 1,575 bar Clear tie bar distance: 370 x 420 mm Minimum mold height: 200 mm Maximum opening stroke: 300 mm Machine weight: 3 x approx. 5,500 kg Machine dimensions: approx. 2,917 x 1,423 x 3,643 mm Documentation and technical documents available Condition: used Disassembly and collection must be carried out by the buyer. Scope of delivery: (See image) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have over the phone.

Year of construction: 2017, condition: ready for operation (used), Clamping force: 1800kN, max. opening stroke: 750mm, min. mold installation height: 300mm, screw diameter: 40mm, L/D: 20, G4 S10, clear tie-bar spacing: tie-barless, max. stroke volume: 220cm³, injection rate: 223cm³/s, max. injection pressure: 1930bar, material barrel: M9 (bimetallic barrel), length: 6455mm, height: 2100mm, weight without mold: 13.7t, operating hours: 59,947h, with documentation. Available from December 2026, an on-site inspection is possible. Hjdjztzqzopfx Akrsnu

Year of construction: 2011, condition: ready for operation (used), A virtually new and almost fully equipped Arburg vertical injection molding machine from a laboratory is available, where its plasticizing unit was never used. Clamping force: 500kN, opening force: 30kN, opening stroke: 250mm, ejector force: 30kN, ejector stroke: 70mm, screw diameter: 25mm/30mm/35mm, nozzle contact force: 50kN, nozzle retraction stroke: 210mm, heating capacity: 9kW, heating zones: 5, hopper volume: 25l, technology level: T2, rotary table diameter: 900mm. Machine dimensions X/Y/Z: approx. 3400mm/2050mm/3500mm, weight: approx. 4200kg, operating hours: 9201h, machine cycles: approx. 120k. The machine was used exclusively for composite materials such as carbon fiber and Kevlar. Documentation available. An on-site inspection is possible. Hjdpfozd Ehxox Akronu

Year of construction: 1996, condition: used, There are two Arburg ALLROUNDER 220S 250-60 available, connected load: 39kW, an on-site inspection is possible. Hjdpfx Akoz Sr Rberjnu

Condition: like new (used), Year of construction: 2019, operating hours: 399 h, functionality: fully functional, clamping force: 2,200 kN, screw diameter: 48 mm, clearance between the columns: 650 mm, displacement volume: 318 cm³, injection pressure: 1,900 bar, mold height (min.): 250 mm, ejector force: 35,000 N, ejector stroke: 150 mm, opening stroke: 550 mm, plate length: 900 mm, plate width: 900 mm, total height: 2,800 mm, overall weight: 10,700 kg, Equipment: documentation/manual, FANUC ROBOSHOT Alpha S-220iA – fully electric injection moulding machine, year 2019 Very lightly used precision injection moulding machine with only 399 operating hours. The FANUC ROBOSHOT Alpha S-220iA combines high repeatability, dynamic movements and energy-efficient production. Suitable for demanding technical plastic parts and reliable series production. Technical data: - Clamping force: 2,200 kN (220 t) - Double-toggle clamping mechanism - Tie-bar spacing: 650 × 650 mm - Platen size: 900 × 900 mm - Mould height: 250–750 mm, extended version - Clamping stroke: 550 mm - Ejector stroke: 150 mm - Maximum ejector force: 35 kN - Screw diameter: 48 mm - Shot volume: 318 cm³ - Maximum injection speed: 200 mm/s - Maximum injection pressure: 1,900 bar - Locating ring: Ø 160 mm - Fully electric drive Hsdpfjznd Dysx Akronu Control and equipment: - FANUC 31i-B CNC control - 15-inch LCD touchscreen - AI mould and ejector protection - Precision metering and pressure-profile functions - Automatic mould-height adjustment - Energy-consumption measurement - Euromap 67 robot interface - Three independent air valves - Cascade control for up to eight valves - USB and memory-card output - Four-circuit flow meter The machine is in like-new condition and fully operational. Inspection is available by appointment. Price, delivery time and further information are available on request.

Condition: used, Year of construction: 1996, functionality: fully functional, High-performance planing and profiling machines / four-sided planer Manufacturer: Weinig Model: Hydromat 30 / H 30 N System originates from a parquet factory Planing width: approx. 220 mm Planing height: approx. 120 mm Spindle arrangement: Bottom (joiner), 22 kW Right, 7.5 kW Left, 18 kW Top, 30 kW Spindle diameter: 50 mm Feed speed adjustable, 12 – 120 m/min. Hjdpfx Aoz D Exbekrsnu Voltage: 380 V, 50 Hz

Condition: excellent (used), Year of construction: 2007, Twin drum spiral hot air oven direct from closed factory, this was used for pre-cooking burgers and nuggets. These machines are built for the high capacity cooking, grilling and steaming of a wide range of products, the degree of cooking, grilling or steaming is determined by the air temperature, the air speed, the air humidity and the time that the product is in the system. Electrically heated. 96m x 600mm belt. Was in use from 2007 until 2016 when the contract moved to another factory. Machine is in lovely condition, we also have everything else used in the factory - formers, fryers, coating machines, filters, spiral freezers, bagging lines etc. Please note that the photos probably show two different ovens, both are very similar. Hodpfomrrwfsx Akrsnu