Used Middle Bearing Gunmetal Blank for sale (4,180)

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, travel distance X-axis: 1,100 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 640 mm, controller model: SIEMENS 840 D, spindle speed (max.): 10,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 1,100 mm Travel range, Y-axis: 500 mm Travel range, Z-axis: 640 mm Number of pallets: 2 Table size: 2 × 1,000 × 450 mm Table load capacity: 600 kg Spindle speed range: 50–10,000 rpm Drive power: 18.5 kW Tool interface: DIN 69871 / ISO 40 Feed rate range X/Y/Z: up to 10,000 mm/min Rapid traverse rate in all axes: 30 m/min MACHINE DETAILS CNC path control: SIEMENS 840 D Number of tool positions: 30 Machine dimensions & weight Machine dimensions L × W × H: approx. 3,605 × 3,041 × 3,220 mm Machine weight: approx. 6,700 kg EQUIPMENT 2-position pallet changer 30-position tool changer Internal coolant supply (ICS) Full enclosure with electrically interlocked safety doors Linear guides with double roller recirculating bearing for even absorption of high torques in all directions Ball screws in all 3 axes Machine bed made of Meehanite cast iron for high precision, rigidity, and vibration damping Swivel chip conveyor with integrated coolant system Preparation for 4th axis Fpjdpfjz Ibb Tjx Afusn CE compliant

Condition: used, 72”x 0.5” x 60,000Lb Braner Turret Type Loop Slitting Line Braner Turret Type Loop Slitting Line is used for coil metal cross cutting with maximum width 72”, maximum 0,5” metal thcikness and 60,000Lb coil capacity Make: Braner Year New: 1996 Material Thickness: .060″ – .500″ Material Width: 12″ – 72″ Coil Weight: 60,000Lb Line Speed: 120 – 250 feet per minute Coil ID: 20″ – 24″ Coil OD: 75″ Slitting Cap: .500″ / 4 cuts – .125″ / 40 cuts Entry L-Type Coil Car Hydraulic Lift & Traverse Self Contained Hydraulics Control Panel Mandrel Uncoiler Powered Hold – Down Roll Outboard Bearing Support Hydraulic Feed-Up Drive Water Cooled Brake Hydraulic Peeling Table Driven Entry Pinch Rolls Adjustable Edge Guides Entry Mechanical Crop Shear Two Turret Type Slitting Heads Arbor Diameter: 12″ Powered Arbor Adjustment Powered Head Rotation Motor: 100HP DC Drive Lots of Knives & Tooling Two (2) Scrap Winders Powered Open / Close Heavy Duty Design Looping Pit Cross Over Table Drag Board Tension Stand Material Feeding Table Recoiler Hydraulic Drum Powered Push Off Hydraulic Over-Arm Separator Outboard Bearing Support 300HP DC Motor Drive Exit L-Type Coil Car Fpedpfxern Sqhe Afuon Hydraulic Lift & Traverse Self Contained Hydraulics Upgraded Siemens Digital Drives, Electrics, Controls, Knives & Tooling

Year of construction: 2020, condition: new, functionality: fully functional, Available in multiple units. Fodpfx Asz I S Ecsfuepn

Condition: used, Material: 1095 High Carbon Steel Tensile Strength: 120,000 PSI Shear Strength: 96,000 PSI Thickness Range: .0045" - .025" Line Direction: Left to Right Cut Width & Thickness .0045" = 1/4" , 3/8" , 1/2" , 3/4" , 1" .0051" = 3/8" , 1/2" , 5/8" , 7/8" .0062" = 3/8" Line Speed: 1500 FPM Entry Strip Width: 18' Traverse Wider Coil Width: 8" Entry Coil ID: 15" - 22" Traverse Winder Coil ID: 11" Exit Coil ID: 16" Entry Coil OD: 54" Ribbon Wound Coil OD: 39" Exit Coil OD: 54" Entry & Exit Coil Weight: 10,000# Traverse Winder Coil Weight: 2250#` Complete Line With: Mandrel Uncoiler Hold Down Roll 3 Leaf Hydraulic Expansion 15 HP Drive Disc Drake Edge Control Unit Fjdpfjztc Tdsx Afuepn Peeler Table / Deflector Roll Newcor Strip Welder with Planishing 2 Roll Material: 1095 High Carbon Steel Tensile Strength: 120,000 PSI Shear Strength: 96,000 PSI Thickness Range: .0045" - .025" Line Direction: Left to Right Cut Width & Thickness .0045" = 1/4" , 3/8" , 1/2" , 3/4" , 1" .0051" = 3/8" , 1/2" , 5/8" , 7/8" .0062" = 3/8" Line Speed: 1500 FPM Entry Strip Width: 18' Traverse Wider Coil Width: 8" Entry Coil ID: 15" - 22" Traverse Winder Coil ID: 11" Exit Coil ID: 16" Entry Coil OD: 54" Ribbon Wound Coil OD: 39" Exit Coil OD: 54" Entry & Exit Coil Weight: 10,000# Traverse Winder Coil Weight: 2250#` Complete Line With: Mandrel Uncoiler Hold Down Roll 3 Leaf Hydraulic Expansion Sliding Base 15 HP Motor 15 HP Motor Disc Brake Edge Control Peeler Table / Deflector Roll Newcor Strip Welder with Planishing 2 Roll Bridal Unit for Tension Control Double Roll Tracking Roll for Strip Alignment 2 Sets of Rubber Coated Deflector Rolls Edge Guides Andritz Slitter Head New in 2016 5" Diameter Arbors 12 Sets of Quick Change Tooling Arbors Pre-Packed Arbors Shimless Tooling Anti Friction Bearings 25 HP DC Drive, 1750/2000 RPM Scrap Baller Recoiler 16" Diameter Drum 10,000# Coil Capacity 30 HP DC Drive Hydraulic Push-Off Hold Down Roll 21" Drum Face 1 Arm Exit Turnstile Vertical Strand Separator Aligns Strips after Exiting the Slitter Deflector Rolls 12 Oscillating Recoilers 11" Diameter Drums Hydraulic Push-Off Vertical Edge Conditioners S Bridal Strip Tension Rolls (2) Hydraulic Traversing Oscillating Wheel 7.5 HP Drive 1 Arm Exit Turnstiles Powerflex Digital Drives 755 Allen Bradley PLC Digital Drives Digital Readouts Central Hydraulic Units Operator Push Button Stations Slitter Tooling Hydraulics & Electrics

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT22001007597, empty load weight: 6,200 kg, maximum load weight: 11,800 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 05/2018, loading space height: 200 mm, total length: 11,600 mm, total width: 2,550 mm, suspension: air, tire size: 235/75 R17,5", color: red, Equipment: center pivot plate, Archive images! Chassis: Steel welded construction, double-curved with low-bed at the front and rear of the axle assembly, low-bed inclined for easy access, turntable with robust ball bearing race, foldable rear support, shims, side impact protection, quarter-panel fenders Lashing points: above the front axle: 2 pairs of ring lashing points, each 5 tons, at the front on the low-bed / rear axle: 6 pairs of lashing points on the side in the low-bed, each 8 tons. 6 pairs of lashing points, each 5 tons, between the longitudinal beams, a pair of stake pockets embedded in the outer frame, inner dimensions 70 x 40 mm, or instead of stake pockets, 5-ton ring lashing points embedded in the floor. Drawbar: tested 40 mm drawbar eye Axles: BPW drum brake axles Braking system: 2-line pneumatic braking system, spring-loaded parking brake, 2 non-interchangeable coupling heads at the front Electrical system: 24 volts, multi-chamber lights, yellow side lights, 2 white position lights at the front 2 white/red marker lights at the rear, rotating beacon with bracket, pair of illuminated and extendable warning signs up to 3,000 mm, 2 x 7-pole non-interchangeable plugs at the front Floor: front curve with steel/diamond plate surface, storage compartment embedded in the ramp incline, driving area and in the middle between the beams with steel/diamond plate surface, rear incline with 70 mm softwood floor, low-bed platform including rear incline 5900 mm Fjdpfx Afoi Ri N Usuopn Ramps: attachment rail for aluminum ramps over the entire width, as a U-profile over the entire width Pair of aluminum ramps 800 mm long, approx. 400 mm wide, load capacity per pair 14,000 kg, Storage compartment for ramps between the beams Approval: contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear.

Condition: new, Year of construction: 2021, Transnorm belt curve conveyor left GKF 180°-1270-1100-IR1200 -- NEW RA1945 Technical data: Conveying length middle radius (NL): 5498 mm Frame width (NB): 1270 mm Frame width with Bearing cover: 1390 mm Frame width with Bearing cover and gearbox: 1480 mm belt width (GuB): 1100 mm height (BH): 250 mm height motor below: 300 mm height including motor (MH): 550 mm Inner radius (IR): 1200 mm Conveying angle: 180° degrees middler conveying speed (v m/s): 1,4m/s Drive: SEW motor motor with frequency converter Electrical data: 50Hz V380-500, kW 3 / S1 Belt: KT 96 new Year of construction: 2021 Height Sideguides: 194 mm Optionally available: Supports Prices net plus VAT from central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Fedpfxjq N Hmhs Afuspn Your specialist and contact for intralogistics

Condition: good (used), Year of construction: 2006, functionality: fully functional, Tank volume: 60 liters and 30 liters Fpedpfx Aszwmxljfuen Motor power: 1.9 kW Power supply: 3 x 400 V (three-phase current). Speed: Continuous mechanical regulation (variator) in the range of approximately 53 to 288 rpm.

Condition: new, range L-W-H 1980x510x1860 mm weight 195 kg Fjdpfx Afeu Imh Ajujpn 15 St. weight max. in kg 700 kg Professional workbench / tool trolley Internal dimensions of the top left 3 drawers 395 x 395 x 65 mm. Internal dimensions of the middle 3 drawers 815 x 395 x 65 mm. Internal dimensions of the top right 3 drawers 395 x 395 x 65 mm. Internal dimensions of the left 4th drawer 395 x 395 x 140 mm. Inner dimensions of the middle 4th drawer 815 x 395 x 140 mm. Internal dimensions of the right 4th drawer 395 x 395 x 140 mm. Internal dimensions of the left 5th drawer 395 x 395 x 220 mm. Inner dimensions of the middle 5th drawer 815 x 395 x 220 mm. Internal dimensions of the right 5th drawer 395 x 395 x 220 mm. Dimensions of the wheels 150 x 40 mm. Solid wood panel thickness 40 mm. Packaging dimensions 189 x 55 x 80 cm. 4 x 150 mm swivel castor 2x with brake. 2 x robust solid stainless steel handle. 1 x central locking for all drawers. 4 x storage compartment blue. 2 x keys. Non-slip mat in every drawer. Very nice solid wood panel. Massive ball bearing slide. (Double bearing) All lower drawers are equipped with 2 runners. All drawers can be opened 100%.

Condition: new, Year of construction: 2026, A very strong 240 cm wide frameWith hillformersCondition: NewSuitable laying plastic on ridges or flatbedFixed middle frame with a minimum inter row distance of 30cmTrack distance is adjustable Suitable for several types of foilThe machine is prepared to also be used as a wide 1-row machine, when the middle element is dismantled Fjdjz Rc Axopfx Afuspn Optional: Drip hose layer How to instal the film in the machine? Place the roll of plastic on the large discs and small rubber wheels. The roll should protrude about 8-10 cm outside the wheels.Use the stop rods to adjust the roll and prevent lateral displacement, leaving 1 cm of slack.Turning the wheels in the dirving direction will unroll the plastic. Pull the lever to separate the nylon pulley and release it once the plastic has reached the floor. See also the video. More information or a quote? Do this quick and easily via the Duijndam Machines website! You can also give us a call. See all the available machines at our website. Since 1977 supplier of reliable used agricultural and horticultural equipmentMachines are checked for deliveryExperienced teamWe can help you with getting the machine to your company Duijndam Machines The specialist in used agriculture and horticulture machinery

Condition: used, Year of construction: 1999, functionality: fully functional, pressing force: 630 t, year of last overhaul: 2023, Equipment: CE marking, documentation/manual, Precision cutting press with coiler and straightening machine Fpedpfxozrw R Uj Afuon Table size: 1,350 mm x 950 mm Good condition, from series production, regular maintenance.

Condition: new, range L-W-H 1830x510x1860 mm weight 195 kg 15 St. weight max. in kg 700 kg Professional workbench / tool trolley Dimensions of the right 3 upper drawers 41.5 x 39 x 8 cm. Dimensions of the right 4th drawer 41.5 x 39 x 15 cm. Dimensions of the right 5th drawer 41.5 x 39 x 23 cm. Dimensions of the middle 3 upper drawers 83.5 x 39 x 8 cm. Dimensions of the middle 4th drawer 83.5 x 39 x 15 cm. Dimensions of the middle 5th drawer 83.5 x 39 x 23 cm. Dimensions of the left 3 upper drawers 41.5 x 39 x 8 cm. Dimensions of the left 4th drawer 41.5 x 39 x 15 cm. Dimensions of the left 5th drawer 41.5 x 39 x 23 cm. Dimensions of the back wall 183 x 46 cm. Dimensions of the closets 183 x 30 x 46 cm. Dimensions of the shelf 22.5 x 63 cm. Wheel diameter 150 mm. Maximum capacity of the wheels 175 kg. Per bike. (700 kg total) Maximum capacity per tray 30 kg. Dead weight 195 kg. Overall dimensions 198 x 51 x 186 cm. Packaging dimensions 190 x 60 x 95 cm. Fpedju Imfhepfx Afuen Equipped with 4 high-performance steering wheels, 2 of them with brakes. All drawers are equipped with non-slip mats. The open compartment and the drawers can be locked separately. Solid wood worktop 4 cm thick. Solid pullouts with ball bearings (double bearings)

Condition: new, Year of construction: 2025, A very strong 240 cm wide frameCondition: NewTrack distance is adjustableRow distance is adjustable with fixed middle elementSuitable for several types of foilThe machine is prepared to also be used as a wide 1-row machine, when the middle element is dismantled Optional: Drip hose layerHillformers How to instal the film in the machine? Place the roll of plastic on the large discs and small rubber wheels. The roll should protrude about 8-10 cm outside the wheels.Use the stop rods to adjust the roll and prevent lateral displacement, leaving 1 cm of slack.Turning the wheels in the dirving direction will unroll the plastic. Pull the lever to separate the nylon pulley and release it once the plastic has reached the floor. See also the video. Fedpsz Rdcmsfx Afuepn More information or a quote? Do this quick and easily via the Duijndam Machines website! You can also give us a call. See all the available machines at our website. Since 1977 supplier of reliable used agricultural and horticultural equipmentMachines are checked for deliveryExperienced teamWe can help you with getting the machine to your company Duijndam Machines The specialist in used agriculture and horticulture machinery

Condition: new, axle configuration: 3 axles, loading space length: 9,200 mm, loading space width: 2,200 mm, loading space height: 2,500 mm, loading space volume: 50 m³, Year of construction: 2025, Equipment: ABS, Reisch 3-Axle Tipper Semi-Trailer, Aluminum Large-Volume Body, 50 m³, AluBox-R---- Vehicle is factory new, unused, and not yet registered. Includes aluminum package, consisting of: Fpjdpfx Ajylfcyofujn * Aluminum rims, Alcoa * Aluminum landing gear, JOST * Aluminum air tank Technical data (equipment): * Tipper body: approx. 9,200 x 2,200 x 2,500 mm * Volume: approx. 50 m³ * Fifth wheel height: approx. 1,150 mm (unladen) * Tare weight: approx. 5,980 kg (without spare wheel) * Body painted in RAL 7004 Gray * Chassis painted in RAL 9005 Deep Black * Axle assembly: SAF INTRADISC CD Ø430 ET120 disc * Axle lift acting on the 1st axle * Starting aid acting on the 1st axle * 6-ply tires: Bridgestone Duravis RT-2, 385/65 R22.5 (road version) Without spare wheel * Aluminum rims, Alcoa LVL ONE * Wheel nut covers * Frame made of steel S 700 * Tipper support legs, aluminum (manufacturer: JOST) * Underrun protection made of aluminum, manually foldable, spring-supported * Lateral underrun protection made of aluminum according to ECE regulations * KNORR BREMSE Pneumatic system ILVL * Tire pressure monitoring system TPMS * Air tank made of aluminum * Lighting: 24V ASPÖCK FULL LED ECOLED II * Reversing lights, 2 pieces * Chocks, 2 pieces * Mud flaps on the rear fenders * Loading pressure gauge * Broom and shovel holder on the side, including broom and shovel * Rear apron, semi-trailer apron, Reisch * Access ladder, 3 m, on the side of the chassis * Tool box * Water tank, tipper body * Tipper floor made of 7 mm * Side walls made of 2.1 mm * Inside the tipper body: LED work lights (side, operated with a switch) * External combination doors, split in the middle, with 2x grain slides (also available with a swing tailgate) * 2x grain slides including sack outlet * Including additional manual tensioning latches * 4-hook locking mechanism (mechanical) * Double pendulum bearing * HYVA high-pressure 250 bar front lifting cylinder * Hydraulic connection hose on the semi-trailer * Pressure connection: Hyva 1" coupling * Steel standing platform with access on the front left/right * 3x adjustable crossbars including lashing straps * 3x tarpaulin crossbars integrated into the tarpaulin * PVC tarpaulin in 900g/m² quality * Tarpaulin color: black * 1x work light in the tipper body, operated from the outside * HYFIX low-level fastener on the underside of the tipper body

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT44001000966, empty load weight: 9,400 kg, maximum load weight: 30,600 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 10/2010, loading space length: 7,145 mm, loading space width: 2,750 mm, loading space height: 900 mm, total length: 12,120 mm, total width: 27,500 mm, total height: 900 mm, suspension: steel, tire size: 235/75 R17,5", color: red, The images shown are archive photos! Permissible / technical gross weight: 24,000 / 40,000 kg Permissible / technical payload approx.: 14,600 / 30,600 kg Permissible / technical axle load: 24,000 / 40,000 kg Unladen weight (basic version) approx.: 9,400 kg +/- manufacturing tolerance Overall length approx.: 12,120 mm Overall width max.: 2,750 mm Neck length approx.: 2,850 mm Low bed platform length in wheel track area incl. rear bevel approx.: 7,145 mm Rear bevel length approx.: 850 mm Frame width approx.: 2,750 mm Loaded bed height in low bed approx.: 900 mm Drawbar height approx.: 950 mm Drawbar length approx.: 1,700 mm Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection 1 plastic toolbox, Extendable width up to 3,250 mm (not at rear bevel) (track width of machine/vehicles to be transported must not exceed outer frame width of 2,750 mm) Storage compartment for wooden boards in the center of the loading area 70 mm wooden boards for extension to 3,000 mm 2 pairs of stake pockets in the low bed recessed into the longitudinal beams Lashing points low-bed: 2 pairs of lashing eyes on neck, 5 tons each 1 pair of lashing eyes in rear bevel 4 lashing eyes recessed in the middle of the floor 2 pairs of keyhole profiles in wheel track area for insertion of longitudinal guide rails and as additional lashing option 6 pairs of lashing pins recessed in outer low-bed frame, 10 tons each 5 pairs of stake pockets recessed in the outer frame of the low bed 4 additional pairs of 10 ton lashing eyes: - 1x on neck - 3x recessed in low bed floor Trailer towing device, turntable design Drawbar with certified 50 mm towing eye Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber mounts and mechanical axle load equalization front and rear (rocker balancing) Wheels and Tires 235/75 R 17.5" Steel twin wheels, factory silver finish Brake System 2-line compressed air brake system Spring-loaded parking brake 2 foolproof couplings at front, with interconnecting lines to tractor ABS and ALB, with ABS socket at front and connection cable Note: The trailer may only be towed by vehicles ensuring proper ABS functionality! Floor Neck area with steel / checker plate covering Followed by 70 mm softwood floor; in wheel arch area steel / checker plate Fpjdpoyxq A Hjfx Afusn Rear bevel with 70 mm softwood floor Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable, with wooden covering Hydraulically operated via tractor auxiliary drive Operating Notes At 10,000 kg axle load, an exemption permit is required, only indivisible loads permitted! Note! Oversize length and width require a permanent special permit. When applying for an exemption for regulated heavy haulage, an axle load indicator is required for air-suspended vehicles! This applies to any deviation from § 34 StVZO (axle and permissible total weight overrun), which requires an exemption under § 70 StVZO. The specified gross weight is technically possible; depending on the load, the total weight permitted by axle, support, and kingpin loads may not be achieved. (Poor driving or tracking behavior may occur due to improper load distribution) The images shown are archive photos!

Condition: like new (used), Year of construction: 2006, operating hours: 671 h, functionality: fully functional, total height: 2,992 mm, total length: 3,980 mm, total width: 2,580 mm, overall weight: 8,500 kg, operating hours of spindle: 671 h, number of slots in tool magazine: 48, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, We offer this as new Quaser MV154 APC/P vertical machining center, year of construction 2006. The machine has 9039 power-on hours, but only 671 spindle-hours, this has been confirmed in the parameters aswell. The machine has seen very little usage. When i bought this machine the linear guides for the X & Y axis was worn out as they had not been lubricated properly and with the incorrect grease. These have been swapped for brand new ones, aswell as most of the air and coolant hoses. All the lubricating lines for the X & Y guides and ballscrews have also been renewed. There are some tools in the 48 tool magazine aswell. It also has a 3D Taster. Fpjdpfx Afezxz Dfsusn The chip conveyor also has new bearings and seals. Two Hilma vices could also come with the machine. I have done a ballbar test and checked the machine to be in great working order. The size of the machine also makes transportation easy, as it will fit inside a standard curtain semitrailer. If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: new, Number of boring motors 1 St. boring of corner bearing 1=yes, 0=no 1 ja boring of olive 1=yes, 0=no 1 ja Götzinger Olive drilling machine type OBM-PLUS (corner and scissor bearing + handle olive drilling) Pos. 1 ----- Vertical drilling unit with drill head quick-change device Pneumatic feed via foot valve 1 adjustable back stop 2 swiveling workpiece supports 1 machine stand complete with shelf 220/400V, 50Hz, 1.1KW Pos. 2 ----- Drill head BKF 3, 21.5 mm pitch, quick-changeable Drill holder M 10, cyl. right/left complete with stop system 2200 mm long Total length with 10 folding stops adjusted to constant Grip size (olive drilling) Pos. 3 ----- 1 set of drills (for handle olives) consisting of: 2 dowel drills d = 10 left 1 artificial drill d = 25 (or according to your choice or manufacturer fittings) Pos. 4 ----- Drill head BKF 2/3 can be changed quickly 2/3 spindles for corner bearings drill on the loose frame part (Sigenia, Maco, Roto, Winkhaus, GU) complete with stop system with 2 folding stops Pos. 5 ----- Drill 2 cylinder head drills for corner bearings ----- Basic price in the above version Pos.1 - Pos.5 on request! ----- Special accessories with additional charge: Fpsdpfjygm Tcsx Afuen -Folding stop per piece, EUR 110,00/piece -Stop system for central drilling, EUR 1,980.00 -chassis, EUR 920.00 -Roller conveyor right/left 1.5 m, 200 mm wide complete with 4 rollers each, EUR 1,940.00 -Conversion kit for PVC with steel insert Oil brake cylinder for uniform feed speed PVC support to prevent the profile from tipping over Reduction gear for low speed, EUR 1,790.00 -Drill set for PVC with steel insert, EUR 420.00 2 step drills d = 12 mm left 1 piece step drill d = 12 mm right -2 pieces of additional stops for the stop in the tilt window, EUR 180.00 -2 pieces of additional pneumatic stops for gripping the entire fighter groove, EUR 1,650.00 -2 pieces of additional pneumatic stops for gripping the dowel hole in the Fighter area complete, EUR 1,650.00 -4 additional pneumatic double stops for gripping the dowel hole in the fighter area complete, EUR 1,980.00 PS: If the dowel hole is in the middle, 1 stop on the right/left is sufficient. If the dowel hole is off center, you need 2 stops on the right/left. -Packaging 1 box Packaging 1 pallet with foil, on request ----- We will be happy to send you the price list with all options upon request. (Technical information according to manufacturer - no guarantee!)

Condition: ready for operation (used), Year of construction: 2023, operating hours: 362 h, functionality: fully functional, machine/vehicle number: 12430021383, travel distance X-axis: 750 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 560 mm, controller model: Siemens 840D sl Operate, spindle speed (max.): 20,000 rpm, Auction of a DMG DMU 75 Monoblock + Pallet Handling PH150! Only 362 spindle hours! TECHNICAL DETAILS Travel in X-axis: 750 mm Travel in Y-axis: 650 mm Travel in Z-axis: 560 mm Main drive and spindle Fpjdpfxsz I Tcie Afuon Main drive: AC motor, digitally controlled Motor spindle: speedMASTER Warranty period of the motor spindle: 36 months Speed range: max. 20,000 rpm Spindle mount: HSK-A 63 Acceleration time: approx. 2.6 s Deceleration time: approx. 2.6 s Drive power at 40% duty cycle: 35 kW Drive power at 100% duty cycle: 25 kW Spindle torque at 40% duty cycle: 130 Nm Spindle torque at 100% duty cycle: 86 Nm Spindle bearing inner diameter (front): 80 mm Spindle bearing inner diameter (rear): 55 mm Number of T-slots: 4 × 14 H12 T-slot spacing: 63 mm Centering bore: 50 mm Thread: 8 × M12 Tilting axis A Tilting angle towards the working spindle: +120° Tilting angle away from the working spindle: −120° Torque of tilting axis: 3,400 Nm Holding torque of tilting axis: 3,400 Nm Holding torque of tilting axis with hydraulic clamping: 6,200 Nm Rapid traverse of tilting axis: 40 rpm Feed rate of tilting axis: 20 rpm Input and display resolution: 0.001° Bidirectional accuracy of tilting axis A: A ≤ 9 arc seconds Permissible moment of inertia of tilting axis: max. 59 kg·m² Rotary axis C Rotary range of C-axis: 360° Torque of rotary axis: 2,000 Nm Holding torque of rotary axis: 2,000 Nm Feed rate of rotary axis: 7,200°/min Bidirectional accuracy of rotary axis C: A ≤ 7 arc seconds Table load: max. 600 kg Permissible moment of inertia of rotary axis: max. 48 kg·m² Workpiece diameter: max. 840 mm Machinable diameter: 650 mm Workpiece height: 500 mm MACHINE DETAILS Control system: Siemens 840D sl Operate Cooling system: Liquid cooling Lubrication: Oil-air lubrication Operating hours Power-on hours (according to counter): 1,166 h Spindle hours (according to counter): 362 h Further technical data can be found in the attached offers.

Condition: used, Year of construction: 2005, functionality: fully functional, machine/vehicle number: 62005_2.0x3.0-30HP, table length: 3,000 mm, table width: 2,000 mm, year of last overhaul: 2025, total length: 3,500 mm, total width: 2,500 mm, Equipment: safety light barrier, NEC / DUAL HEAD Power Jet Systems Multi-Axis Waterjet Cutting Table Sold with x2 Digital Control High-Pressure Waterjet Pumps HP Pump Models: SX 222 V3 (Yr. 2005) Pump & SX 245 Pump (Yr. 2001) Plus, includes KMT Abrasive Hopper TWIN HEAD Industrial CNC Waterjet Cutting System: Manufactured by NEC Power-Jet Systems, this heavy-duty multi-axis waterjet cutting table is designed for precision cutting applications using pure water and/or abrasive waterjet technology. The machine features a rigid steel box-frame construction with integrated water tank, servo-controlled motion system, and industrial CNC control software. Suitable for engineering, fabrication, stone, glass, plastics, composites, rubber, foam, and metal cutting applications. Key Features: Multi-axis CNC waterjet cutting table Precision Ball Screw or Precision Rack & Pinion drive systems Linear bearing slideways Baldor digital servo motors and drive system Touchscreen operator interface Dedicated waterjet cutting software Integrated water tank/cutting table Adjustable water level system Abrasive distribution system mounted on gantry or Z-axis carriage Pure water and abrasive cutting capability Multi-head cutting configurations available Heavy-duty steel framework construction Stainless steel and anodised aluminium wetted components CAD/CAM compatibility with kerf compensation Nesting and material optimisation capability Dry-run facility and programmable jogging functions Technical Specification Construction Rigid heavy-duty steel framework Integral cutting tank and table Enclosed drive systems Cable trunking for protected service routing Local abrasive transfer unit Stainless steel and anodised aluminium wetted parts Integrated operator panel and electrical controls Motion System Precision Ball Screw drive (MaxiJet models) Precision Rack & Pinion drive (MidiJet models) Linear bearing guideways Baldor digital servo drives and motors Multi-axis configurations available: 2, 3 or 5-axis systems Software & Control Proprietary Power Jet cutting software CAD/CAM import capability Kerf compensation Material nesting and optimisation options Programmable jog speed control Home and return-home functions Dry-run programme verification Standard Machine Sizes MaxiJet: High-precision CNC waterjet table Ball screw drive system Standard cutting area: 2m x 3m Applications / Suitable for cutting: Steel Stainless steel Aluminium Stone Glass Plastics Rubber Foams Composite materials Technical engineering materials Fpsdpfx Asz Nll Hofusn NEC Power Jet CNC Waterjet Cutting Machine | Multi-Axis Abrasive Waterjet Table | Servo Controlled Search Keywords Waterjet cutter, CNC waterjet, abrasive waterjet machine, pure waterjet cutter, Power Jet Systems, MaxiJet, MidiJet, industrial cutting table, CNC cutting machine, water jet cutting system, fabrication equipment, engineering machinery.

Condition: used, functionality: fully functional, Year of construction: 2016, machine/vehicle number: 2016-08-30, total length: 2,100 mm, total width: 1,200 mm, total height: 1,900 mm, overall weight: 2,500 kg, CONGDA 16/16/6 Counter-Pressure Filling Machine – up to 3,500 bottles/hour For sale: a CONGDA 16/16/6 bottle filling machine, manufactured in 2016. The machine underwent a complete overhaul in April 2026, which included replacing bearings, seals, springs, and other wear parts. In addition, the machine has been technically improved in several areas since it was put into operation. During this process, various original components were replaced with high-quality parts from European manufacturers. Technical specifications - Manufacturer: CGET (China) - Year of manufacture: 2016 - Configuration: 16/16/6 (rinsing / filling / capping) - Filling system: Counter-pressure filler - Filling capacity: Up to 3,500 bottles per hour, depending on factors such as carbon dioxide content and temperature - Bottle format: Set for 33 cl Longneck bottles - Weight: Approximately 2,500 kg - Documentation: Technical documentation available Complete overhaul in April 2026 In April 2026, the machine underwent an extensive technical overhaul. During this overhaul, the following parts, among others, were replaced: - Bearings - Seals - Springs - Various other wear parts Additional technical improvements Since it was put into operation, the machine has been further optimized in several areas. Various original components have been replaced with parts from European manufacturers. The most important improvements are: - Replacement of the vacuum pump - Replacement of all sensors - Installation of a digital pressure gauge on the filling bowl - Replacement of various parts of the rinser - Replacement of the capping dies - Various other technical improvements As a result of these modifications, the machine has been technically improved in several key areas compared to its original configuration. Additional items included The machine comes with a comprehensive package of extra parts, including: - Various chain conveyor parts - Large quantity of spare parts - Extra seals - Springs - Filling tubes - Various other technical parts and wear parts Fedpfxez Nlcxe Afuspn Asking price: €34,900,- excluding VAT Location: Breda More information, photos, and videos are available upon request.

Condition: used, functionality: fully functional, FAG 24056-K-B Spherical Roller Bearings – Refurbished / Excellent Condition – 2 pcs available Available: 2 FAG spherical roller bearings, model 24056-K-B, disassembled from an industrial plant and in full operational efficiency. High-end components, engineered for heavy-duty applications, ideal as immediate replacement parts or to reduce downtime. Technical Specifications Fpsdpfjyu Rh Tjx Afusn Brand: FAG Model: 24056-K-B Type: spherical roller bearings Tapered bore (K) High radial and axial load capacity Suitable for: industrial gearboxes lifting equipment heavy machinery quarries, cement plants, steel mills snowmaking systems / industrial pumps Condition Used, but in perfect working condition Removed from operating equipment No signs of damage on raceways and rollers Excellent running smoothness Properly stored in crate Ready for reinstallation

Condition: new, functionality: fully functional, inner diameter: 160 mm, outer diameter: 275 mm, grinding wheel width: 160 mm, Reishauer grinding wheel blanks, new – unused – unprofiled 6 pieces, EK article E04239 Manufacturer: Reishauer Reishauer article no. 418041.36 Specification: A80G8V0167, 80 m/s Fedpfx Afoz Ah Raeujpn 1 piece, EK article E04514 Manufacturer: Reishauer Reishauer article no. 418041.38 Specification: A120G8V0176, 80 m/s SITAB grinding wheel blank, new – unused – unprofiled 7 pieces, EK article E01117 Manufacturer: SITAB Specification: 9A120.1J9V101PF, 80 m/s Dimensions for each: 275x160x160 mm (outer diameter/inner diameter/width) e.g., suitable for a Reishauer grinding machine RZ160 / RZ260 A.M.O. - Schnarrenberger Price on request All technical specifications are subject to typographical errors and errors. Sale exclusively to countries within the EU.

Condition: used, maximum load weight: 37,300 kg, overall weight: 43,000 kg, axle configuration: 3 axles, first registration: 04/2008, next inspection (TÜV): 07/2027, total length: 9,720 mm, total width: 2,500 mm, Year of construction: 2008, Additional information: * Type | First axle: Goodyear R * Tire size | First axle: 385/55 R22.5 * Tire tread depth inner left | First axle: 40% * Tire tread depth inner right | First axle: 40% * Maximum axle load | First axle: 9000 kg Fedszpdg Repfx Afuepn * Type | Second axle: Goodyear R * Type | Third axle: Goodyear R * Tire size | Second axle: 385/55 R22.5 * Tire size | Third axle: 385/55 R22.5 * Tire tread depth inner left | Second axle: 40% * Tire tread depth inner left | Third axle: 40% * Tire tread depth inner right | Second axle: 40% * Tire tread depth inner right | Third axle: 40% * Maximum axle load | Second axle: 9000 kg * Maximum axle load | Third axle: 9000 kg * Position | First axle: Rear * Brand | First axle: Other * Brake type | First axle: Disc brakes * Suspension | First axle: Air suspension * Lift axle | First axle: Yes * Position | Second axle: Rear * Position | Third axle: Rear * Brand | Second axle: Other * Brand | Third axle: Other * Brake type | Second axle: Disc brakes * Brake type | Third axle: Disc brakes * Suspension | Second axle: Air suspension * Suspension | Third axle: Air suspension Additional features: * Homepage * Lift axle * SemCollection Semtrade B.V. Contact | Martin Klaaijsen | Tel: | Whatsapp: | Email: Export costs | Please inquire about the costs and procedures for your specific country in advance. Location | Maasdijk (NL) | 140 km from the border | 20 km from Rotterdam The Hague Airport Disclaimer: Subject to changes, prior sale, and errors. The stated prices exclude BPM (Dutch motor vehicle tax) and are only valid for export.

Condition: used, Year of construction: 2013, operating hours: 6,226 h, load capacity: 4,000 kg, lifting height: 5,500 mm, fuel type: diesel, construction height: 2,600 mm, gearing type: automatic, Equipment: cabin, head guard, In accordance with our “General Terms and Conditions,” without any guarantee or warranty, we can offer you the following vehicle, subject to final sale, errors, typographical errors, and prior sale: Still reach truck R-70-40 with triplex mast Year of manufacture: 2013 Operating hours: 6,226 Fpsdoz Rkt Ejpfx Afuon Lifting height: 5,500 mm Mast height: 2,600 mm Next inspection: 08/2027 Transmission: 20 km/h VW engine, diesel/electric 55 kW / 75 hp 2 work lights at the rear 2 work lights at the top front + 2 in the middle 1 double-acting hydraulic cylinder at the front Load capacity: 4,000 kg Unladen weight: 6,421 kg Load center: 500 mm Turn signals Windshield wiper Fixed cabin with glass windows Tires: 250-15 (250/70-15), front approximately 50% remaining, rear approximately 40% remaining Tow hitch at the rear Price: €10,500.00 (net) All information is provided without any guarantee or warranty. Our “General Terms and Conditions” apply. The place of jurisdiction for both parties for disputes up to a value of €10,000 is the local court of Ludwigslust; for disputes exceeding this amount, it is the regional court of Schwerin. Subject to errors, typographical errors, and prior sale.

Condition: used, Year of construction: 1990, pressure 35 t no. of strokes ca 72 Hub/min Fodpfoztf Anjx Afujpn dayligth 195 mm total power requirement 1,5 kW weight of the machine ca. 330-400 kg

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, spindle speed (max.): 5,000 rpm, controller model: INDEX C200-4, TECHNICAL DETAILS Main Spindle Spindle bore with collet clamping: 65 mm Spindle diameter in the front bearing: 100 mm Speed: max. 5,000 rpm Spindle nose according to ISO 702/1: Size 5 Torque at 100%: max. 62/95 Nm Power at 100%: max. 13/20 kW Turret 1 Number of tools: 8 Tool system according to DIN 69 880: 25 mm Indexing time for 1 station: 0.2 s Cross Slide 1 XZ Slide travel X-axis: 90 mm Slide travel Z-axis: 280 mm Feed force X-axis: 5,500 N Feed force Z-axis: 5,500 N Rapid traverse X-axis: 24 m/min Rapid traverse Z-axis: 24 m/min Resolution X-axis: 0.0005 mm Resolution Z-axis: 0.001 mm Turret 2 Number of tools: 6 Indexing time for 1 station: 0.25 s Fsdpfx Ajz Im Urofujpn Cross Slide 2 XZ Slide travel X-axis: 81 mm Slide travel Z-axis: 80 mm Feed force X-axis: 8,300 N Feed force Z-axis: 5,500 N Rapid traverse X-axis: 16 m/min Rapid traverse Z-axis: 24 m/min Resolution X-axis: 0.0005 mm Resolution Z-axis: 0.001 mm Driven Tools Speed: max. 6,000 rpm Torque: max. 8 Nm Tool holder bore: 25.4 mm MACHINE DETAILS Control system: INDEX C200-4 Correction accuracy: 0.001 mm Input accuracy: 0.001 mm Output accuracy: 0.001 mm Coolant system Pump capacity: 60 l/min at 5.5 bar Pump capacity: 20 l/min at 20 bar Filling volume: approx. 210 l Hydraulics Delivery rate: 19 l/min System pressure: 90 bar Filling volume: 50 l Dimensions & Weight Footprint: 3,708 (2,495) × 1,240 mm Height: 1,750 mm Floor space requirement without material handling: 3,708 (2,495) × 1,890 mm Weight: approx. 2,500 kg Three-phase connection: 400 V, 50/60 Hz Connected power: 20–45 kVA Protection of the mains supply line: 35–80 A EQUIPMENT