Used Parmel Gmbh, Caron Technology Feeder for sale (82,926)

Condition: as good as new (ex-display), Year of construction: 2023, operating hours: 35 h, functionality: fully functional, total width: 87 mm, total length: 120 mm, maximum load weight: 200 kg, heating capacity: 7.2 kW (9.79 HP), tank capacity: 400 l, warranty duration: 24 months, type of input current: three-phase, inner dimension height: 600 mm, inner dimension length: 800 mm, inner dimension width: 500 mm, overall weight: 150 kg, input voltage: 400 V, input frequency: 50 Hz, workpiece weight (max.): 200 kg, LCT NW 180 BSS demonstration tank Dual frequency 27/80 kHz Ventilated stainless steel control cabinet Hinged lid Tank completely insulated Stainless steel washing cork with four crane eyes and a basket bar for lifting Four adjustable feet for uneven floors Floor emptying via ball with inclined tray base for complete emptying Floor grating Bottom and 2 x side sound with a total output of 3000 watts Bjdpfx Asq Rd R Dshmsln Timer with timer and program control Connected load 10.2 KW

Condition: new, Year of construction: 2022, functionality: fully functional, type of input current: three-phase, power: 50 kW (67.98 HP), input voltage: 400 V, fuel: domestic gas H, overall weight: 2,200 kg, nominal power: 50 kW (67.98 HP), input frequency: 50 Hz, continuous power: 50 kW (67.98 HP), input current: 72 A, Equipment: documentation/manual, For sale: new and unused 2G g box 50plus combined heat and power (CHP) unit from 2022. This is a 2G Energietechnik g box 50plus, configuration as70 4, suitable for simultaneous generation of electricity and heat using natural gas. The unit has never been put into operation and is in new condition. At full load, the CHP unit delivers 50 kW of electrical power and approximately 104 kW of thermal power. The unit is designed for 400 V and 50 Hz and is equipped with a Liebherr G924 natural gas engine and a Leroy Somer LSAH 44.3 generator. Technical specifications: • Manufacturer: 2G Energietechnik GmbH • Type: g box 50plus • Configuration: as70 4 • ID number: H1214 • Year of manufacture: 2022 • Electrical power: 50 kW • Thermal power: approximately 104 kW • Rated voltage: 400 V • Rated frequency: 50 Hz • Rated current: 72 A • Weight of CHP module: approximately 2,200 kg • Fuel: natural gas • Electrical efficiency: approximately 34.5 percent • Thermal efficiency: approximately 71.8 percent Bljdpfez Hngmjx Ahmen • NOx emissions: less than 125 mg per Nm³ • Sound pressure level of CHP: approximately 55 dB(A) at 1 meter The offered package consists not only of the CHP module. The installation also includes two Viessmann boiler bodies, one Viessmann Proflame VM IV 3 gas burner, a separate control cabinet, and various flue gas components, fittings, and related documentation. The original new price of the complete installation was approximately €189,000. The installation comes from a project for which it was ultimately not used. The various main components are from 2022 and have been stored without being put into operation. Due to the size and composition of the installation, we advise interested parties to contact us in advance for further technical information, photos, documentation, and an overview of the components available. An inspection is, of course, possible (location: Winterswijk, Netherlands). Loading onto the buyer's transport vehicle is possible on site.

Condition: good (used), Year of construction: 2020, functionality: fully functional, total length: 9,000 mm, Adhesive application cell with ABB robot IRB 4600-60/2.05. Included in the adhesive application cell: Robot (weight 425 kg, payload 60 kg, year of manufacture 2020) 7th axis + steel structure (unlike in the images, the axis and steel structure have been extended to approximately 9 m) Adhesive application units Protective fences, etc. Not included: Roller shutter doors Fixturing device (available separately) Bjdpfx Ajzz Agmshmeln Detailed drawings available upon request.

Year of construction: 2019, operating hours: 3,000 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: 10031325, This is a high-resolution NIR system capable of detecting particles in the 3 mm size range. Additionally, the machine is equipped with an electromagnetic detector that has a sensitivity of approximately 1.5 to 1 mm, depending on the metal type. Blodpfx Ahjzl Uzwemon Depending on the settings, it can sort positively or negatively. Technical data: Belt width: 1024 mm Nozzle bar: 6.4 mm working width Upon request, complete documentation can be provided. The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price does not include packaging on a pallet.

Condition: used, Year of construction: 2013, functionality: fully functional, machine/vehicle number: NS-009-0000-300, type of input current: AC, nominal power at 50% duty cycle: 250 kVA, throat depth: 300 mm, short-circuit current: 50,000 A, input voltage: 400 V, type of cooling: water, total width: 1,000 mm, total length: 1,000 mm, total height: 1,850 mm, overall weight: 1,000 kg, open-circuit voltage: 22 V, Zens Multifunction Resistance Welding Machine 250 kVA MF – 23 kN – 50 kA – Year of Manufacture 2013 Bsdpfx Aszqucfohmjln For sale is a high-quality Zens multifunction resistance welding machine in a robust industrial design. The system was developed for demanding resistance welding processes and is ideally suited for series production in the automotive, supplier, electrical, and metal industries. The machine operates with modern medium frequency (MF) technology and achieves a welding power of 250 kVA at a 50% duty cycle. The powerful SER medium frequency inverter (700 A) enables a maximum welding current of 50 kA and ensures maximum process stability as well as reproducible welding results. With a maximum welding force of 23 kN and an overhang of 300 mm, the system is suitable for a wide range of resistance welding applications. Technical Data Manufacturer: Zens Machine Type: Multifunction Resistance Welding Machine Year of Manufacture: 2013 Welding Power: 250 kVA (Medium Frequency / MF) at 50% duty cycle Max. Welding Current: 50 kA SER Medium Frequency Inverter: 700 A Welding Control: SER-Mega1 Maximum Welding Force: 23 kN Overhang: 300 mm Equipment CE-compliant protective enclosure CE safety light curtain Welding table for welding forces up to 23 kN Pressure compensation tool QSF-M quality assurance system Position measuring system for process monitoring PLC control (Siemens S7) Robust industrial design for continuous industrial operation The combination of powerful medium frequency technology, precise force and position control, and modern PLC and SER welding control ensures high process reliability and consistently reproducible welding results. Thanks to the complete CE safety equipment, the machine can be easily integrated into existing production lines. The system is in good condition and can be inspected and demonstrated at any time by prior appointment.

Condition: excellent (used), Year of construction: 2019, operating hours: 288 h, functionality: fully functional, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 150 mm, positioning accuracy: 0.01 mm, workpiece weight (max.): 1,100 kg, type of input current: three-phase, input voltage: 400 V, pressure: 4,000 bar, positioning speed: 6,000 m/min, water pressure: 4 bar, power: 37 kW (50.31 HP), Waterjet Cutting System All-Powerful Science & Technology Stock Co., Ltd APW 3015 BA Year of manufacture: 2019 Lightly used, very good condition Operating hours: 288 cutting hours, 2203 operating hours Travel distance X: 3000 mm Travel distance Y: 1500 mm Travel distance Z: 150 mm Maximum feed rate: 6000 mm/min Maximum pressure: 410 MPa (4100 bar) Continuous operating pressure: 340-360 MPa (3400-3600 bar) Blodpfx Ahszh Eq Ujmon Swiveling cutting head, deflection range 0-10° Cutting accuracy: ± 0.1 mm The components used are from well-known manufacturers, e.g. SKF, Yaskawa, TBI Motion, etc. The high-pressure pump is from A&V Waterjet Tech Inc. USA A second, unused spare high-pressure pump is also installed. Machine dimensions, cutting table: 4200 x 2800 mm Space required for cutting table & control & pump & water filtration system and abrasive feed system approx. 6 x 5 m Water requirement for cutting at least 3.7 l/min, recommended 10 l/min Maximum workpiece weight: 250 kg/m² Axis drives: AC servo Pump power: 37 kW Connection: 400 V, 3-phase Special accessories, included in the price: Spare high-pressure pump Positioning laser Collision protection Air conditioning unit for oil cooling CAM software with part placement 4 clamping units 1500 kg abrasive blasting sand Removable protective covers Wastewater filtration system with filter fleece (Matchling MCL-P5N) Spare parts and wear parts set The machine is located in a precision engineering workshop. The protective covers reduce dust levels. Optional Commissioning, price based on effort Basic training, price based on effort

Year of construction: 2022, operating hours: 6,123 h, condition: used, functionality: fully functional, machine/vehicle number: 20-22-004, Like new, hardly used. Blsdpfxeziaqfs Ahmon

Condition: used, AZO GmbH big bag discharging station with metering screw and vibrating base Includes buffer silo, vibrating base, and metering screw with end gate. Includes platform and staircase. Includes filter housing with dust extraction system, 1500 m³/h. Frame made of coated steel. Big bag discharging station entirely made of stainless steel. Bsdpfx Aoz Hc T Ishmoln See our other listings.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 531 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. Bsdez Agv Uspfx Ahmjln - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 532 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. Bjdjz Agw Eepfx Ahmsln - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 533 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. Bsdpez Ag Rrofx Ahmoln - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Condition: ready for operation (used), Various SMT feeders are available. 12x vibratory feeders, 189x 8mm feeders, 21x 12mm feeders, 13x 16mm feeders, 12x 24mm feeders, 8x 32mm feeders, 3x 44mm feeders and 10x feeder carriages. Bedpfjtz Dkaox Ahmsln

Condition: used, Year of construction: 2012, functionality: fully functional, machine/vehicle number: K 300712/595, overall weight: 2,900 kg, total width: 125 mm, total length: 330 mm, total height: 225 mm, Bledez Dcaiopfx Ahmon

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: 13100019, type of input current: three-phase, overall weight: 1,000 kg, For sale: a professional log edging saw (optimizing saw) from the renowned German company Winter Holztechnik, model Optimax 100. The machine is fully functional, regularly serviced, and ready for immediate operation. It is ideally suited for the fast and precise removal of defects and the preparation of elements with fixed lengths in joinery workshops. Key features and advantages: PLC control: Intuitive touchscreen panel for easy programming. Multifunctionality: Capability for sequential cutting (memory for up to 10 dimensions) and cutting lines marked with fluorescent chalk. Efficiency: The machine can replace the work of several people, offering a speed of up to 80 cycles per minute. Precision: Very high cutting accuracy of +/- 1 mm. Technical data: Saw motor power: 7.5 kW. Bjdjzzw Ulspfx Ahmeln Feed motor power: 2.0 kW (feed speed continuously adjustable up to 80 m/min). Cutting height: max. 100 mm. Blade diameter: Ø 455 mm (bore 30 mm). Minimum material length: 300 mm. Power supply/Air: 400V / 8 bar.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 530 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible Bledpfx Ahszz Rpcjmsn - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Condition: used, Year of construction: 2021, functionality: fully functional, machine/vehicle number: 1605269/1, total width: 630 mm, total height: 1,115 mm, total length: 1,010 mm, working width: 460 mm, input voltage: 400 V, type of input current: AC, overall weight: 200 kg, power: 0.37 kW (0.50 HP), roller diameter: 100 mm, passage height: 80 mm, feed rate X-axis: 35 m/min, height adjustment type: mechanical, tank capacity: 2 l, roll width: 450 mm, input frequency: 50 Hz, workpiece height (max.): 80 mm, Equipment: double-sided, For sale is a well-maintained glue and roller application machine from Axel Wirth Maschinen GmbH, type LW 100/450. The machine was manufactured in 2021, has comparatively few operating hours, and is in technically perfect and well-maintained condition. A particular advantage is the adjustable working speed or feed rate (6 - 35 m/min). This allows the machine to be flexibly adapted to different workpieces, materials, and application media. The machine is mounted on a sturdy, mobile base with lockable wheels. As a result, it can be easily moved within the production area and safely positioned at the respective location. A total of two identical machines are available. The stated price applies per machine. An attractive package price is possible if both machines are purchased. The LW 100/450 is suitable for the uniform application of liquid and pasty media onto flat or textured workpieces, for example: - Glue and adhesive - Oil and wax - Stain and primer - Paints and dispersions - Resins and comparable application media Among other materials, wood, solid wood, parquet flooring, chipboard, cork, cardboard, metal, stone, rubber, and insulation materials can be processed. The application quantity can be adjusted via the lateral adjustment devices. The rollers and glue trays can be removed with a few simple steps, making the machine easy to clean. Technical data and equipment Manufacturer: Axel Wirth Maschinen GmbH Blsdszr H Aaepfx Ahmon Type: LW 100/450 Year of manufacture: 2021 Nominal width: 450 mm Working width: approx. 460 mm Passage height: approx. 80 mm Diameter of the application rollers: 100 mm Capacity per glue container: approx. 2.3 liters Drive power: 0.37 kW Adjustable working speed or feed rate Application rollers above and below Separate control cabinet Main switch and emergency stop Mobile base with lockable wheels CE marking Condition: used, well-maintained, and technically perfect Operating hours: comparatively low Inspection and test run are possible after prior appointment. Collection at the Leun location. Shipping by freight forwarder can be organized if required, upon agreement. If you have any questions or are interested, please do not hesitate to contact us. We will be happy to provide further information and photos. Price: €5,900 (negotiable) per machine plus VAT (can be shown). Package price for both machines: on request All information is provided to the best of our knowledge. The sale takes place under the conditions applicable to the seller for used machines.

Condition: new, Diamond Cube – Fiber Laser Cutting System | Compact | Precise | Efficient The Diamond Cube is a space-saving and high-performance fiber laser cutting system for professional metal processing. It is ideal for companies that want to combine high cutting quality and economical production in a compact machine. Technical highlights: – Working area: 3000 × 1500 mm (standard format) – Laser power: available in various power levels depending on the configuration – Material processing: steel, stainless steel, aluminum, etc. Bedpfsfz Di Asx Ahmsln – Maximum material thickness: up to approx. 40 mm (depending on the power) – Positioning speed: up to 120 m/min – Precise servo drive & robust gantry design – Front loading with pull-out table for quick part changes, load capacity up to 1.4 t – Modern CNC control with integrated CAD/CAM software – Low maintenance requirements thanks to fiber laser technology Advantages for your production: – High cutting quality and repeatability – Compact design – minimal space requirement – Fast changeover times and easy operation – Very good economy and low operating costs – Ideal for small to medium-sized series as well as job production The Diamond Cube is the ideal solution for companies in the steel construction, mechanical engineering, and metal processing industries that want to modernize their production and rely on a reliable, precise, and energy-efficient laser cutting system.

Year of construction: 2021, condition: like new (used), functionality: fully functional, Component 1: ATM-800 P Tangential Dereeler (2 pieces) Heavy-duty dereeler for controlled unwinding of copper wire coils. • Max. coil diameter: 800 mm • Max. coil width: 300 mm • Pickup hole: Ø52 / Ø56 mm • Max. coil weight: 300 kg • Braking force: 100 - 2000 N • Brake torque: 3 - 800 Nm • Max. speed: approx. 5 rpm • PLC control with torque sensor Component 2: HBK-40-S Automatic Taping Machine Professional automatic taping machine for coil and conductor insulation. • Servo-controlled taping head • Operator terminal and display Blodpfoz Ap R Isx Ahmsn • Integrated X-axis guidance • Electric hysteresis brake • Automatic overlap control via encoder • Suitable for various insulation materials

Condition: like new (used), Year of construction: 2014, operating hours: 10 h, functionality: fully functional, Fiber optic optical inspection system with various endoscopes, as shown in the attached photos. Bedez Dicqopfx Ahmsln

Condition: used, functionality: fully functional, Year of construction: 2017, Operational condition 3D AOI machine. Ask for specification! Bledpfx Ahsw Ty Hcemsn

Condition: good (used), Year of construction: 2023, functionality: fully functional, type of input current: three-phase, total height: 1,200 mm, total width: 790 mm, total length: 1,200 mm, input voltage: 380 V, ground cable length: 3,000 mm, overall weight: 205 kg, warranty duration: 12 months, type of cooling: water, hose package length: 5,000 mm, input current: 16 A, laser power: 2,000 W, laser wavelength: 1,080 nm, Equipment: documentation/manual, type plate available, Handheld Laser Welding Machine AIRTECH 2kW – Top Technology for Efficient Sheet Metal Welding Demonstration Unit – Excellent Condition Discover the smart and high-performance solution for precise laser welding: the Airtech handheld laser welding system with 2,000 watts of power! Perfectly suited for demanding sheet metal fabrication – efficient, safe, and highly versatile. Highlights and Features: - Power output: 2,000 watts for superior weld quality and speed - Laser wavelength: 1080 nm, continuous operation with modulation frequency up to 20 kHz - Handheld laser welding head – ideally designed for ergonomic operation - Robust housing and intelligent internal structure for maximum durability - Touchscreen display for intuitive operation - Optional automatic multifunctional wire feeder - Safety features: three-color alarm, safety interlocks, and protection against operating errors - Cooling via separate water circuit with 13-liter tank capacity - CE-certified components according to European standards Your Benefits - Work safely thanks to comprehensive protection mechanisms and alarm systems - Flexible applications, including automatic wire feed and robot integration - Low operating costs and easy maintenance due to well-designed engineering and long-life components Bledpfx Ahon Sl Dbemsn For more information or consultation, the Airtech team will be happy to assist you!

Year of construction: 2013, operating hours: 7,700 h, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 12090, This is a recycling extruder with side feeding for materials (flakes, pellets, etc.). The system is supplied with a control cabinet and a double vacuum system. The pelletizing system is missing at the end of the screw – it is not included in the scope of supply. The cylinder ends at the flange. The extruder is supplied without a screw. The frequency inverter for the main motor was replaced with a new unit 3 years ago. Installed power approx.: 474 kW Cooling water requirement approx.: 190 l/min Fresh water consumption approx.: 110 l/h Feeding system: • Diameter of the feeding screw: 200 mm • Drive for the feeding screw: 45 kW, frequency-controlled • Hopper capacity net 7 m³/250 ft³, • Gear motor 3 × 3 kW • 2 sight glasses in the hopper • 2 level indicators Extruder: • Diameter of the extruder screw: 145 mm • L/D ratio: 24 • Heating power: 50 kW • Extruder drive unit 280 kW Vacuum 1: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 11 kW • Vacuum capacity: 225 m³/h • Vacuum pressure: 33 mbar Vacuum 2: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 7.5 kW • Vacuum capacity: 190 m³/h • Vacuum pressure: 33 mbar Cylinder: • Cylinder: Bimetal extruder cylinder, • Reinforcement layer 1.8–2.0 mm thick, • Hardness 63–65 HRC Installation conditions: • Voltage: 3 × 400 Volts Blodpfoznz Ezjx Ahmon • Permissible fluctuation max.: +5 % – 5 % • Frequency: 50 Hz Permissible fluctuation max.: +4 % – 4 % • Protective measure: Multiple grounding • Ambient temperature: min. 15 °C, max. 35 °C • Humidity max.: 90 % • Altitude of the installation site: 0 – 1000 m The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center is being closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price is without packaging.

Condition: used, Year of construction: 2009, functionality: fully functional, machine/vehicle number: K 220808/309b, overall weight: 2,850 kg, total width: 125 mm, total length: 330 mm, total height: 125 mm, Bljdpfx Ahez Db Tuomen

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 2080092, Used CNC horizontal 5-axis twin-spindle double-table machining center Manufacturer: SW – Schwäbische Werkzeugmaschinen GmbH Type: BAW06-22 Bsdpfxsz E Ddfe Ahmoln Year of manufacture: 2011 Machine No.: 2080092 Weight: approx. 16,000 kg Technical data: - CNC horizontal machining center - 5-axis design - Twin spindle - Double table - Travel ranges: - X-axis: 600 mm - Y-axis: 600 mm - Z-axis: 510 mm - Rapid traverse: up to 45 m/min - Tool interface: HSK-A63 - Spindle speed: up to 17,500 rpm Equipment: Machine with standard accessories. Availability: Available in the short term.

Condition: new, Year of construction: 2025, Sharpening of woodworking tools The Profi Firmer ( piercing bag) and Planer knife grinding machine Blsdpfxeb Dt Ixe Ahmon WOOD TOOL GRINDER WTG -1 - "Swiss quality" For an accurate and efficient work perfectly honed, razor-sharp cutting edge is a must. With our grinder to sharpen your tools " wood chisel (holly bag) , planer knives , chisels , chisel " , fast, easy , accurate and inexpensive ... Currently, the absolute cheapest PROFESSIONAL wooden tool grinder on the market! Made in Switzerland Swiss Quality = Where the WOOD TOOL GRINDER is " WTG -1" used? • Wherever conventional wood is processed. • For example, in carpentry , joinery , • Carpeting , schools, trade schools , • schools / training workshops ... Base machine price : EUR 2050.00 (ex works , excl 8.0 % VAT) You win and this several times ! If you regrind a wood chisel or a hand planer blades by hand or with an " older machine " experienced artisans need 5 min or more per tooth , if not even longer and get a good result ! With the WTG you need just about 30 seconds per tool . In no time you grind even a whole set of tools. And that, too, without having any special knowledge or grinding years of experience . So the machine can pay for itself relatively quickly. But above all, can be obtained every year , high , variable costs for tools and grinding work to a minimum . Once in possession of a WTG machine, you just have to work with perfectly cut tools , which has a positive impact among others on the quality and speed of operation. Go with the time ... go with BERGER technology GmbH. Your direct contact persons : Grinding Technology : Marc Broennimann Kaindl, DAREX, HARICH, Vertex, Drill Doctor, METEOR, Optima, Tatar, Promac, Cuoghi, Avyac, Christen, MOTOM, VITAX, WASU, Ulrich Klingel, ISELI, Schneeberger, Lamallo,