Used Heating Furnace For Powder Paint for sale (20,975)

Year of construction: 2003, condition: used, functionality: fully functional, machine/vehicle number: HWO 1/9-5.2​, - The system is located at the Geberit Keramik GmbH site in Wesel. - The system, including the associated safety technology, performs technical flash firing and re-firing and is prepared for this purpose. - Maximum firing temperature [°C] = 1300 Dcjdpfjzu Nvzox Adrsn - Current operating temperature [°C] = 1238 - Number of burner groups = 10 - Number of burners = 38 - Number of kiln cars = 18 - Number of kiln cars in the kiln = 9 - Current firing cycle [h] = 17 - 23 - Gross energy consumption [kcal/kg] / [kWh/kg] = 785 / 0.912 - Specific energy consumption [kcal/kg] / [kWh/kg] = 1459 / 1.696 - Gas connection capacity [m³/h] = 770 - Usable waste heat [m³/h] = 4000 - Standard loading quantity [pieces] = 900-980 ceramic products Dimensions of the housing: - Length [m] = 14.4 - Width [m] = 6.4 - Height [m] = 5.7 - Volume density [m³] = 146.3 Dimensions of the kiln car: - Effective length [m] = 1.45 - Effective width [m] = 5.2 - Effective height [m] = 2.156 - Track gauge [m] = 1.5 (2x) Special features: In 2023, the kiln was completely overhauled and brought up to the latest state of the art. The following changes were made: - Renewal of the kiln roof: The fiber lining in the upper area was replaced with cordierite stones. - Renewal of the burners, including new nozzles, flame tubes and controllers. - Replacement of the media valves; installation of servo motors on the gas and air lines in front of the burners. - Installation of new software; the Simatec control panel was replaced – control is now exclusively via the PC. - Replacement of the O₂ control system; installation of a Zerox probe; installation of an O₂ analyzer for O₂ correction (to improve energy efficiency by approximately 12–14 %). - The system must be dismantled, packed and collected independently by the buyer.

Condition: new, V160mm/120mm L200mm Djdpfslp Hvhjx Adrjcn

Condition: new, Hemming tool for Amada/promecam Dcedpfx Ajqxq Hbsdrsn

Condition: new, Hemming tool for Lvd/Trumpf Dcodpfxoi Hbcwo Adron

Condition: new, punches and dies for EHT press brake Dsdpfxoiq Dnks Adrjcn

Year of construction: 2026, condition: new, functionality: fully functional, machine/vehicle number: V80mm, V65mm/V80mm press brake dies For Trumpf, Bystronic Dsdpfx Aelkdczjdrscn Full body hardened HRC 55

Year of construction: 2026, condition: new, functionality: fully functional, machine/vehicle number: KP, Compatible with Amada, promecam, Durma, Ermaksan, Baykal, YAWEI, Ital, Dener, This high-precision gooseneck punch is fully manufactured according to Amada European standard specifications, perfectly compatible with Amada press brakes and most mainstream European-style bending machines. Designed specifically for complex sheet metal bending, this gooseneck upper tool effectively solves the interference problem that ordinary straight punches cannot avoid during deep bending, reverse flanging, U-shaped grooving and multi-angle forming. Featuring an optimized curved gooseneck structure, the punch provides sufficient avoidance space during bending. It prevents collision with vertical edges and folded surfaces, allowing one-step integral forming of deep cavity workpieces, box structures and special-shaped sheet metal parts. It greatly reduces secondary cutting, welding and reshaping procedures, improving workpiece integrity and production consistency. Made of high-quality alloy tool steel with integral vacuum quenching and tempering treatment, this Amada-style punch delivers high hardness, outstanding wear resistance and strong compression resistance. CNC precision grinding ensures stable bending angles, smooth forming surfaces and long service life without deformation under continuous high-load operation. Standard size tolerance and unified positioning structure enable seamless installation with Amada punch holders and clamping systems, ensuring high repeat accuracy during batch production. Ideal for electrical cabinets, equipment housings, automotive sheet metal and custom metal bending parts, this gooseneck upper punch significantly upgrades your bending efficiency and finished quality. Key Features ✅ Fully compatible with Amada standard press brake tooling systems ✅ Anti-interference gooseneck design for complex one-shot bending ✅ High-strength heat-treated alloy steel for long service life ✅ CNC precision grinding for stable bending accuracy ✅ Greatly reduces secondary processing and production costs Dcsdpfx Asqxq Nwsdron ✅ Widely used for cabinet, automotive and mechanical sheet metal fabrication

Condition: excellent (used), Year of construction: 2008, operating hours: 84,000 h, functionality: fully functional, power: 526 kW (715.16 HP), type of cooling: air, input frequency: 50 Hz, Jenbacher J312GS hours: 84,000 hours overhaul at 60,000 hours. Year: 2008 Rated power: 526KW Frequency: 50HZ Dedpfjzwpnpox Adrscn Very well looked after unit was installed in a hospital and serviced and maintained regularly.

Condition: like new (used), Year of construction: 2022, immediately available, warranty 12 months, excellent condition Forced convection oven for solvent-containing substances according to DIN EN 1539, 4 charging carts available on request (see image) - Max. temperature 150°C - Usable volume 1875 liters - Internal dimensions: W 1250 x D 1000 x H 1500 mm - External dimensions: W 1765 x D 1425 x H 2300 mm Dodpfxexbtvfj Adrocn - Guide rails and recesses for loading the oven with a charging cart - Maximum permissible amount of flammable substances at 150°C: 83.9 g - Minimum exhaust air flow rate at 20°C: 360 m³/h - KS controller 40-1 for simple temperature control with defined ramp or hold times (1 program, 4 segments) - Controller upgrade to JUMO DICON available on request - Additionally, a simple timer is integrated, which can be started via front buttons - Connection: 30 kVA, 3 x 400 V, 57 A, 50 Hz - Heating power: 36 kW - Weight: 820 kg - Includes 4 charging carts, each with 12 trays and 24 insertion levels, available in stainless steel - Documentation, CE declaration - Electrically tested and with current DGUV test report Inspection in our warehouse by appointment. Oven, drying oven, baking oven, heating oven, industrial oven, solvent oven, paint drying oven, annealing oven, heating oven, temperature oven, drying cabinet, chamber oven, chamber dryer, sintering oven, convection drying cabinet, convection oven

Condition: new, Year of construction: 2027, Recirculating air chamber oven, electric, new unit, delivery time 17-18 weeks -Temperature 300°C -Internal dimensions W x D x H: 1500 x 3000 x 2000 mm -External dimensions W x D x H: 2410 x 3560 x 2730 mm -Volume: 9000 liters -Control system: Eurotherm Nanodac, 100 programs with 25 segments each -Additional 100 programs can be saved/loaded via FTP or a USB flash drive -2 recirculating air fans -Double door with safety door sensors Dcjdslkb Ezepfx Adron -Over-temperature protection, Eurotherm 3216i -Control system/recorder with color touch display -Stable steel construction, anthracite exterior -Motorized dampers -Electrical version: 400 V / 50 Hz / 3NPE -Increased heating capacity: approx. 70 kW -Guide rails, recess for driving in a trolley -Documentation, CE declaration of conformity -Electrical wiring diagram with spare parts list We will gladly offer transport, installation, and training for your employees. As a new unit, it is also available with an exhaust fan and other equipment! Delivery time approx. 10-12 weeks. Please contact us! We offer new and used industrial ovens, which we can also modify and supplement according to customer requirements. Inspection in our machine hall is possible at any time by appointment. Oven, ovens, drying oven, industrial oven, drying cabinet, heating oven, heating cabinet, recirculating air oven, chamber oven, heating oven, chamber recirculating air oven, annealing oven, tempering oven.

Condition: good (used), Year of construction: 2010, operating hours: 18,523 h, lifting height: 6,500 mm, fuel type: diesel, mast type: duplex, fork length: 2,400 mm, Transmission: Powershift, 4 gears Year of manufacture: 2010 Lifting capacity: 15.000 kg Maximum passing height: 5.500 mm CE mark: yes Technical condition: good Visual appearance: good Price: On request = Additional options and accessories = - Twin wheel axle = Remarks = Clean and tidy 15 tons forklift, complete with heavy new forks, AC, central greasing system, partikelfilter, 6-cilinder Cummins diesel engine, Michelin tyres 75% Capacity forks: 22000 kg at 600 mm Minimum width forks: 960 mm Maximum width forks: 4350 mm Width forkcarriage: 3250 mm (can be taken off) Dodpfxoq Ulb Dj Adrjcn Transport can be arranged..

Condition: new, NEW Electric heat plates suitable for most electric Teflon band grills (contact grills) such as GEA, CFS, Koppens, Square, etc ... in casted aluminium dimensions : 590 x 600 x 67 mm Djdpszy Nwcjfx Adrscn 15 kW - 3 x 400 V - 50 Hz stainless steel connection hood stainless steel attachments

Condition: new, Siemens certificate 6AU1820-0AA44-0AB0 Technology Option MultiAxes Package for D445/D445-1/D445-2/D455-2. Unused, 100% functional, scope of delivery as per photos. Dcjdpfxjzzhruo Adren

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: 140563, power: 1,300 kW (1,767.51 HP), overall weight: 2,600 kg, total width: 1,424 mm, total length: 3,787 mm, total height: 2,402 mm, pressure: 6 bar, heating capacity: 1,300 kW (1,767.51 HP), fuel: domestic gas H, operating pressure: 6 bar, Equipment: hot water, Bosch Unimat UT-L 10 industrial low-pressure hot-water boiler, manufactured in April 2023. Technical data: - Manufacturer: Bosch Industriekessel Austria GmbH - Model: Unimat UT-L 10 - Year of manufacture: 2023 - Serial number: 140563 - Rated thermal capacity including ECO: 1,300 kW - Maximum allowable pressure: 6 bar - Hydraulic test pressure: 9.6 bar - Allowable temperature range: 0–110 °C - Total boiler volume: 1,370 litres - Approximate dimensions: 3,786 × 1,424 × 2,402 mm - Approximate net boiler weight: 2,600 kg - Heating medium: low-pressure hot water - Design: three-pass flame-tube/smoke-tube boiler - Flue/appliance classification: EN 1749, B23 - CE marking: CE 0085 - Manufactured in Austria - Type plate available The stated dimensions and weight are manufacturer reference values for the UT-L 10 boiler body. Actual dimensions and transport weight may vary depending on the installed burner, economiser, fittings and control equipment. Fuel type and electrical connection data must be taken from the installed burner and control-cabinet nameplates. The exact scope of supply, operating condition and included documentation should be confirmed before purchase. Sale subject to prior sale and verification of the technical information. Dcsdpfx Adjzp Rmqjren Included equipment, as shown in the photographs: - Natural-gas regulating and supply line - Gas pressure regulator - Gas meter - Pressure gauge - Motorised Bosch valve actuator - Butterfly shut-off/control valves - Associated pipe sections, flanges, gaskets and mounting components The components are supplied dismantled. Completeness and suitability for the buyer’s installation must be verified before commissioning.

Condition: good (used), Year of construction: 2006, functionality: fully functional, overall weight: 4,000 kg, heating capacity: 198 kW (269.20 HP), large warm air furnace for firewood and residual materials External dimensions approx. 3.5 m x 1.5 m x 3 m Weight 4 t with control system Djdpfx Adsw Ucfdorjcn with warm air blower

Condition: used, functionality: fully functional, With this offer, you are purchasing a used large format printing system/plotter ‘Mimaki TxF150-75’. Item for sale: 1 x Mimaki TxF150-75 with the following equipment: incl. Schulze Powder Machine 600 Condition: This offer is for a used device, which may show signs of wear (minor scratches or yellowing). The device has been tested for functionality. A test print can be seen in the photo. Packaging and shipping: Dcodpfx Adjylud Tsren You are welcome to view the device during our business hours. Please make an appointment! Seaworthy packaging and worldwide shipping available on request! A function test will be recorded on video for you before shipping or collection. For more information, please feel free to contact us personally.

Condition: new, Equipment: lighting, Take your painting process to a new level - with mobile convenience. Mobile paint booths in container design for painting and coating various objects. They are specially designed for mobility so that they can be easily transported and set up on different construction sites. The booth is usually equipped with a ventilation system to ensure air quality, lighting and a filter system that prevents paint mist from escaping. The ventilation system ensures that the vapors and particles released during painting are kept inside the booth so that there is no danger to the environment. Mobile paint booths are a practical and flexible solution for companies that need an effective painting system that can be moved from one construction site to another at any time. Overview of the design and functions Our mobile 20-foot Sapi painting containers consist of a robust steel frame with welded wall and ceiling panels. Inside, we can add special equipment such as cranes or lifting devices. The floor is made of tear plate. There are ventilation grilles in both door leaves, which are fitted with fine-pored filter mats. One leaf is designed as an escape door for safety reasons and has a viewing window. It should also be mentioned that these are not simply converted shipping containers! We manufacture all our containers from scratch ourselves. We only use the most stable materials that meet the requirements and have also been tested and proven in terms of safety. Normal shipping containers would not meet the required safety standards. Paint extraction system in the mobile painting container Dcjdpfsun Shgsx Adron The paint mist extraction wall for paint mist separation is located in front of the rear wall and is equipped with multi-layer filter mats. The extraction wall consists of a galvanized housing, edged with baffle plates including various suspension and fastening elements for the filter equipment. The powerful and EX-protected extraction fan with drive motor is installed on a console in the rear wall area on the outside of the container. Next-generation mobile spray booths: meeting EU requirements and advancing coating solutions The new generation of mobile spray booths must meet the highest EU requirements. The consideration of new paint systems such as hydro paints, polyurethane resins, epoxy-zinc dust or epoxy-iron-mica paints places high demands on existing paint booths. That is why we have developed a new and unique mobile paint booth for the next generation of coating solutions. An important criterion is the transportation of the workpieces for painting and for further processing steps. Do you need more information? Our engineers can offer expert advice and support. Whether paint mist dry separation or wet scrubbing, air humidification or air drying, condensation drying in a low-temperature process or hot air drying, whether pre-treatment of the workpieces by high-pressure washing with water flow in a circulation system or by compressed air blasting or wheel blasting technology.

Condition: excellent (used), Year of construction: 2022, operating hours: 600 h, functionality: fully functional, machine/vehicle number: PO210417, total width: 4,600 mm, total length: 25,000 mm, total height: 3,000 mm, type of input current: three-phase, energy consumption: 1,700 kWh, input current: 2,230 A, The AG series of convection tempering furnaces with forced air circulation (Northglass fifth-generation furnaces, featuring proprietary focused convection technology) was developed to meet the growing customer demand for more efficient low-E glass tempering, improved product quality, and reduced energy consumption. The AG series furnace integrates the advantages of a four-convection furnace, primarily offering benefits in terms of higher productivity, superior product quality, and easier process control. The furnace consists of loading conveyors, a heating section, a convection system (upper and lower), a flat tempering/cooling section, and an unloading conveyor. The equipment package includes air ducts and a device control system. Max. working width: 2,850 mm. Max. loading length: 5,000 mm. Max. glass loading area: 2,850 x 5,000 mm (5-19 mm), 2,850 x 4,600 mm (4 mm). Upper fan convection: 6 fans x 4 kW, lower: 6 fans x 3 kW. Main technical data is attached in a PDF file. Dcjdpfjz Dhm Uex Adrsn

Condition: ready for operation (used), machine/vehicle number: 89915, Drive system = compressed air, Material/air ratio = 16:1, Maximum material pressure = 90 bar, Air inlet pressure = 1 to 6 bar, 4 double strokes per 1 liter of material, with MX type spray gun with double hose, Dcsdpfxoiv Huwj Adrsn unused since the last maintenance in 01/20, Condition as inspected, Ex works, from warehouse Seevetal, subject to prior sale.

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, Graf Wet Blasting System Machine type: Wet blasting system Manufacturer: Graf Technik GmbH Type: Compact 2 Plus Year of manufacture: 2013 Control system: Siemens Origin: Germany Location: Albstadt Delivery time: upon agreement Dsdpfoztyzlsx Adrjcn

Year of construction: 2020, condition: excellent (used), overall weight: 255 kg, conveying length: 1,300 mm, transport width: 450 mm, transport height: 950 mm, Plate heat exchanger by VAHTERUS, model PSHE 3HH-242/1/1, insulated. Year 2020. Connections: Lateral DN50, DN65. Top DN150. Bottom DN50. Djdoxnypfopfx Adrjcn

Condition: excellent (used), Year of construction: 2019, Duplo DuSense DDC-810 coating and embellishment machine year 2019 - first installation 2021 very good condition - sparingly used counter reading only 25,000 sheets covered by a maintenance contract until 2026 - latest software corona unit Dcedezy Na Repfx Adron

Condition: used, Universal temperature control unit REGLOPLAS Type 90M/10/SG75/D K/RT50 Pressurized water temperature control unit with electric heating and connections for external cooling Circulating process temperature control for industrial applications in plastics processing, especially for the temperature control of injection molds and other process tools. Manufacturer's serial number: 102010170001, Year of manufacture: 2009 Temperature: max. 90°C (for water) Heat transfer medium: Water Temperature range: +20°C to 90°C Operating overpressure: max. 6 bar Pump capacity: 100 l/min Tank volume: 2.8 liters (internal filling volume) Heating capacity: 10 kW Dsdpfx Adsz Au Hberocn Cooling capacity of heat exchanger: up to 160 kW (depending on the external cooling unit) Pump motor power: 1.5 kW Continuous sound pressure level

Condition: like new (used), Grundfos NB 32-200/206 Single-stage block pump, centrifugal pump Speed: 2915 min⁻¹ Flow rate Q: 33.7 m³/h Head: 46.3 m Max. pressure: 16 bar You are welcome to visit us for an inspection. We can also arrange cost-effective shipping for you! You will receive a proper invoice. Dcjdpfx Aezzllxodron For foreign customers, a net invoice can also be issued. A valid VAT identification number is required. Subject to prior sale. Visit our shop and check out our other offers. The company names and trademarks mentioned are the property of their respective owners and are used solely for identification and description of the products. Deviations from technical data as well as errors in the description of the item may occur and are subject to change.

Condition: like new (used), TETRA PAK CARDBOARD PACKER CBP 32 VERSION 400 YOM 2010 2177 RUNNING HOURS ONLY!! Djdpjya I Sgsfx Adrjcn MULTI PACKER FOR 200/250/1000 ml AS NEW CONDITION LOCATION - POLAND READY FOR SHIPPING