Used Overbeck Internal Grinding Machine for sale (71,627)

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and maximum speed - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements Tsdpfxeuxfu Ne Ahmsc - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Pr...

Condition: new, Eurotec Innovation TV45 – Trough Vibrator / Vibratory Finishing Machine (Made in Germany) The TV45 trough vibrator by Eurotec Innovation is a powerful and versatile vibratory finishing machine for professional surface finishing applications. The machine stands out due to its robust construction, high efficiency, and universal range of applications. Machine type: Trough Vibrator TV45 Shown: TV45 incl. sound enclosure and WS25 for part separation Manufacturer: Eurotec Innovation GmbH Thanks to the U-shaped working bowl, even larger and longer workpieces can be processed efficiently – while maintaining a compact design. The vibration motor mounted directly beneath the working bowl ensures highly efficient energy transfer and consistent finishing results. 🔧 Technical Data: Gross volume: approx. 115 liters Internal dimensions of working bowl: Length: 850 mm Width: 380 mm Height: 395 mm Rated speed: 1500 rpm Power supply: 400V – 16A – 50 Hz Advantages: ✔ Compact and robust design ✔ High energy efficiency due to direct vibration drive ✔ Universally suitable for various workpieces ✔ Deflection edge to reduce part adhesion ✔ Low-maintenance vibration motor ✔ Optionally available with sound enclosure and separation systems 🏭 Applications: Deburring, smoothing, and polishing Descaling, derusting, and cleaning Edge rounding Surface finishing The TV45 is an economical and high-performance solution for companies looking for a flexible vibratory finishing system for a wide range of applications – from individual parts to small batch production. The machine shown in the images includes optional accessories. The listed price refers to the base machine (TV45). A suitable electrical control unit is required for operation. Additional variants and custom configurations are available upon request. Todpfxsf Sqdto Ahmsc From development to production, we provide all products from a single source – all “Made in Germany”. ----- Please feel free to contact us – we will be happy to advise you without obligation. ----- The European Commission provides a platform for out-of-court online dispute resolution (ODR platform). This offer is for presentation purposes only. Contract negotiations are conducted via telecommunications (email, fax, phone, messaging platforms). We will first provide you with a non-binding offer, including our general terms and conditions as well as information on the right of withdrawal and legal notice, before any purchase or contract is concluded.

Condition: ready for operation (used), Year of construction: 2008, grinding length: 1,600 mm, grinding width: 630 mm, Surface grinder 1600 x 630 M7163x16100, magnetic table size 1600 x 630, machine length 5400mm, depth 2500mm, height 2600mm. Automatic feeds in the X and Y axes. We are the first owners; the machine is used on average for a few hours a month for service-related grinding. Year of manufacture: 2008. Power: 22KW, 60A. Shipping costs are borne by the buyer. We can arrange complete container shipping, including packing and loading. Here are two packing options: Option 1 Packing on a pallet + aluminum foil and moisture absorbers Requires a 40' HC container. This is the recommended option, as the vacuum foil and absorbers create a protective barrier against moisture and salt. Cost, including loading and securing the machine in the container: 1800 EUR (net). Option 2 Packing without a pallet, aluminum foil, or absorbers. Loading only into a 40' OT container. Cost: 850 EUR (net). Note: In this case, the machine will be more exposed to moisture and salt. Tedpfx Ahoy Shzaomec Example cost of TRANSPORT ORGANIZATION SERVICE – freight forwarding (all-in), loading Częstochowa, PL, unloading 121001 India, IN, 40 HC, port-to-port, approximately 40 days: 5,050.00 USD.

Condition: used, Year of construction: 2002, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm dimensions of the machine ca. 3,6/3,5 m Photos of identical machine with centre height 225mm Base: Kellenberger Kel-Varia UR175-1000 Kelco 120 Grinding head UR with T1-T2-T3 Basic equipment: -T1 500mm grinding disc diameter -T2 400mm grinding wheel diameter -Infinitely variable, high-resolution axis -Marposs measuring device for tool measurement -Active longitudinal positioning -GAP on T1 and T2 from ELASO contactless integrated in the control interface Semi-automatic balancing from ELASO integrated into the control interface -Tailstock with manual retraction -MK5 workpiece headstock with short taper DIN 55026 Belt-driven internal grinding device Options at an extra charge: - New high-precision workhead with torque drive - Internal grinding device for high-frequency spindles diameter 120mm -HF internal grinding spindle Fischer MFM-1224/42/31 D-21 -HF spindle with HSK holder 24,000 rpm with integrated GAP sensor. (delivery time) -CNC-controlled C-axis non-circular grinding -hydrostatic threaded spindle in x -new hydrostatic unit with only 1 pump and pressure accumulator thus better energy efficiency. -monitoring of the water content in the hydrostatic system -Suction system Further options available on request Mechanical overhaul: -Complete machine overhauled according to Kellenberger measurement protocol -New service-friendly cab -repainting Electrical overhaul: -New modern CNC CIRCULAR GRINDING MACHINE control with BEMA rough grinding surface -New control cabinet -New drive technology -Replacement of all electrical cables Berus pressure switches etc. -New absolute glass scales in x and z -New absolute rotary encoder (for B-axis) Control system: The grinding software consists of a basic licence and various options that are possible depending depending on the equipment of the machine. Basic software - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal taper pendulum grinding - External and internal radius grinding, radius dressed on disc - Semi-automatic pendulum grinding - Workpiece zeroing - Grinding wheel zeroing - Measuring the dressing diamonds - 2 moulding diamonds - 1 shaped diamond or dressing roll (dressing roll required) - Moulding roller (dressing roller required) - 3 Flat dresser - Corrections - Z-position measurement (probe required) - GAP probing (grinding device required) OPTIONS at an extra charge: Tedpfxouxfucs Ahmec Software profile plunge-cut grinding: - External and internal profile plunge-cut grinding with profile disc Profile grinding software: - External and internal profile grinding with straight disc Software thread grinding: - Single and multi-start external and internal thread grinding with thread on the disc disc Dressing. Dressing of single and multi-groove discs. Flank angle freely selectable. Trapezoidal thread grinding software: - Additional dressing of trapezoidal threads possible External and internal non-circular plunge-cut grinding: - External and internal non-circular plunge-cut grinding Non-circular grinding software: A prerequisite for non-circular grinding is that the workpiece axis is equipped with a high-resolution rotary encoder so th...

Condition: good (used), Year of construction: 1981, Surface grinding machine, manufacturer ELB, type: SWBE 010 ND, year of manufacture 1981. Electromagnetic chuck: 1000 mm x 500 mm Grinding area: Length 1000 mm, width 550 mm, height 400 mm Grinding wheel: 500 mm x 50 mm Truing device Paper band filter Wet grinding system Todpjz Dv Exsfx Ahmec Electrical diagrams Space requirements: 4,000 mm x 3,000 mm, height 2,600 mm, weight approx. 3,500 kg.

Condition: used, Year of construction: 1963, overall weight: 1,050 kg, type of input current: three-phase, input voltage: 380 V, power: 2.8 kW (3.81 HP), input frequency: 50 Hz, input current: 7 A, CYLINDRICAL GRINDING MACHINE VEB BWF BERLIN SI 40x70 Model: SI 40X70 Serial number: 1436 Todpfx Ahozl Sn Usmoc Year of manufacture: 1963 Total weight: 1.05 t Circuit arrangement: SI40-60.0 Sp Wiring diagram: SI40-60.0 Lp Type of current: 3-phase AC Frequency: 50 Hz Operating voltage: 380 V Distribution voltage: 220 V Connected power: 2.8 kW Machine rated current: 7 A Rated current (fast): 25 A Permissible protection (slow): 20 A If you have any questions or require further information, please send a message or contact us by phone.

Condition: refurbished (used), Year of construction: 2013, functionality: fully functional, grinding length: 4,000 mm, grinding width: 180 mm, type of input current: three-phase, input voltage: 400 V, grinding spindle motor power: 15 W, G56elT straight knife sharpener automatic, rotatable magnetic table, 4000 mm linear translation guide 3 CNC axes magnetic filter, paper filter Tjdez H Axwspfx Ahmsc front positioning stop, protective bellows

Condition: good (used), Year of construction: 1989, grinding length: 400 mm, grinding width: 200 mm, Grinding area: 400 x 200 mm Magnetic area: 400 x 175 mm Vertical adjustment: 410 mm Grinding wheel dimensions: 225 x 25 x 50.8 mm Grinding wheel speed: 1420 / 2840 rpm Complete with: - Coolant system - Hydraulic unit Tedpfx Ahov Tcy Ujmoc - Documentation Country of origin: Germany Motor power: 1.5 kW Machine dimensions (L x W x H): 2200 x 1500 x 2100 mm Machine weight: 1100 kg

Condition: used, Year of construction: 2017, functionality: fully functional, feed length X-axis: 160 mm, feed length Z-axis: 650 mm, PALMARY GU32X60 NC cylindrical grinding machine, year 2017, designed for external cylindrical grinding operations. The machine is equipped with, among other things, a 40 l/min paper filter, a CM5 collet chuck, and scales on the X and Z axes. TECHNICAL SPECIFICATIONS Capacities Maximum diameter above the table Ø 320 mm Distance between centers 600 mm Maximum external grinding diameter Ø 300 mm Maximum load between centers 150 kg Grinding wheel Grinding wheel dimensions Ø 405 x 50 x Ø 127 mm Linear speed 45 m/s X-axis Manual travel 160 mm Automatic rapid traverse 40 m/min Maximum travel 250 mm Minimum adjustment unit 0.001 mm Handwheel rotation 2 mm Graduation 0.005 mm Z-axis Travel speed 1.5 m/min Maximum travel 650 mm Minimum travel in automatic reciprocating motion 8 mm Travel per handwheel rotation 20 mm Pivot angle -2° to +10° Work spindle Todpfxezzppno Ahmsc Pivot angle -30° to +90° Variable speed 10 to 300 rpm Maximum spindle load, including tool holder 35 kg Maximum length 150 mm Tailstock Travel 25 mm Fine adjustment range ± 0.03 mm Motors Grinding wheel spindle 3.7 kW Work spindle – AC servomotor 0.85 kW Hydraulic pump 0.37 kW Grinding wheel spindle lubrication pump 0.18 kW Coolant pump 0.18 kW EQUIPMENT 40 l/min paper filter CM5 collet chuck X-axis scale Z-axis scale

Condition: used, Year of construction: 2002, Technical details: grinding length: 1500 mm grinding width: 700 mm workpiece height: 580 mm table load capacity: 2380 kp table speed -stepless-: 5 - 35 m/min grinding wheel dia. x width: 500 x 100 x 203 mm grinding wheel motor: 18 kW speeds:: infinitely variable (elektronically) total power requirement: 35 kW weight of the machine ca.: 12 t dimensions of the machine ca.: 5,3 x 2,9 x 3,8 (3,18) m Tedpfx Ahjz Dvidemoc surface grinding machine, paper-filter, DRO 3 axis, automatic infeed, el.handwheel, full cabin *

Condition: used, Year of construction: 1973, Technical details: Tsdpsxu Dv Aofx Ahmoc grinding length: 400 mm grinding width: 200 mm workpiece height: 300 mm dimensions of grinding wheel: 275 - 315 mm magnetic plate size: 400 x 200 mm max. table load: 200 kg weight of the machine ca.: 1,6 t dimension machine xH: 1,55 x 1,45 x 2,20 m

Condition: used, Year of construction: 1988, functionality: fully functional, grinding length: 1,200 mm, grinding width: 400 mm, total height: 2,900 mm, total length: 4,500 mm, total width: 2,400 mm, grinding wheel width: 70 mm, overall weight: 5,500 kg, travel distance X-axis: 1,200 mm, travel distance Y-axis: 400 mm, We provide spare grinding wheels for the machine (2-3 pieces). A centering stand is included. This machine was used in our own production and is currently not in operation, but it was moved and stored in perfect working order. Tjdpsz Hw T Nefx Ahmec During transport, we will assist with loading using our own crane, provided that a truck with top-loading and side-opening capabilities is used.

Condition: excellent (used), Year of construction: 2011, operating hours: 2,352 h, functionality: fully functional, total width: 2,024 mm, total length: 2,670 mm, total height: 1,800 mm, distance between centers: 650 mm, type of input current: three-phase, grinding spindle motor power: 7,500 W, overall weight: 4,000 kg, input voltage: 400 V, The machine is equipped with the following spindles: - External grinding, 7.5 kW - Thread grinding, including grinding cycles, 7.5 kW - Internal grinding spindle, Fischer, 60,000 rpm Automatic B-axis for positioning the grinding spindles. C-axis on the workpiece spindle. Direct measurement for the X and Z axes. Measuring workpiece and tool probe with an automatic cycle. Sensitron on the workpiece spindle. The machine is in very good condition and has been used sparingly. Further information is available in the attached PDF files. Tjdpfx Ahoz Eb Tqsmoc Direct sale to end-users only. W-Technology s.r.o. Polní 8 79201 Bruntál Czech Republic

Condition: ready for operation (used), functionality: fully functional, grinding length 500 mm grinding width 200 mm workpiece height 250 mm table surface 600 x 200 mm grinding wheel dimensions 225 x 20 x 51 mm grinding spindle drive 1.5 kW table feed 1 - 20 m/min Tjdsz Aynwopfx Ahmsc total power requirement 2.6 kW machine weight approx. 2 t machine dimensions approx. 2.6 x 1.6 x 1.8 m

Condition: used, Year of construction: 2019, Used straight-line glass edging machine, NEPTUN, Model Rock 11, Year 2019. Todpfxsz H I E Nj Ahmoc

Condition: good (used), Year of construction: 2011, LANDIS LT-2 TWIN WHEEL CNC ORBITAL CRANK GRINDER Equipped with: Landis 6400 CNC Control Siemens TOUCH HMI Arobetech Steady Rest Marposs P7 Gage System Lateral Locator Twin CBN Grinding Wheels Rotary Dresser Headstock Tailstock Tjdpsrtrxxjfx Ahmec Rittal AC Units Specifications: Maximum Center Distance: 680 mm

Condition: used, Year of construction: 2006, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm weight of the machine ca. 3,5 t Machine completely overhauled with 12 months warranty Tsdot Ii Nbopfx Ahmsc Mechanically and optically like new Photos from the last overhauled machine with different options Fanuc 21i control -Grinding head UR 1-2-3 external/internal/plan -Axis automatic 1° Hirth serration -Active longitudinal positioning KEL-POS Movomatic -Semi-automatic balancing device KEL-BALANCE -Grinding wheel equipment left 400mm diameter -Grinding wheel equipment right 300mm diameter -Internal grinding unit with belt drive -Tailstock with micro-adjustment -fine adjustment upper table -Paper belt filter SBP4 240l

Condition: refurbished (used), Year of construction: 2027, functionality: fully functional, grinding wheel diameter: 600 mm, total width: 2,500 mm, total length: 5,600 mm, total height: 2,300 mm, grinding diameter: 500 mm, type of input current: three-phase, grinding wheel width: 125 mm, feed length X-axis: 430 mm, feed length Z-axis: 1,500 mm, grinding spindle motor power: 20,000 W, overall weight: 7,400 kg, pivoting range: 225 °, input frequency: 50 Hz, controller manufacturer: Sinumerik 840D sl, drive type: Siemens Sinamics S120, control type: CNC control, Equipment: rotational speed infinitely variable, Schaudt precision for shafts up to 1500 mm in length and 500 mm in diameter – completely overhauled and modernized by Serwema Retrofit Solutions, Chemnitz. The PF5 is one of the most reliable external cylindrical grinding machines in its class: rigid bed, 20 kW grinding spindle, 600 kg between centers. Serwema completely rebuilds it, with a Siemens Sinumerik 840D sl, Sinamics S120, direct measuring systems in X and Z, and an automatic B-axis that swivels the grinding spindle from -45° to +225°: longitudinal, face, and taper grinding, shoulder grinding, and with an optional internal grinding spindle, also boring – in a single setup, without manual retooling. Proven Schaudt mechanics, new electrical systems, new drives, new safety technology: you get the performance of a new machine at a fraction of the price, inspected in Chemnitz together with you. Tsdpfez E H Itex Ahmsc The user-friendly interface guides the operator through work piece, wheel, and cycle data screens without the need for programming. Marposs balancing and dressing systems reduce non-productive time and protect the grinding wheel; grinding wheels up to 600 mm in diameter and 125 mm in width with a peripheral speed of 50 m/s allow for high material removal rates during rough grinding and the finest surface finishes during finishing. Application areas: shafts, spindles, rollers, hydraulic pistons, and gear components in mechanical engineering, drive technology, the printing and paper industry, and contract grinding shops. Technical data: max. grinding length 1500 mm, max. grinding diameter 500 mm, work piece weight between centers 600 kg, max. grinding wheel Ø 600 mm, max. wheel width 125 mm, peripheral speed 50 m/s, grinding spindle power 20 kW, X-axis travel 430 mm, B-axis swivel range -45° to +225°. Dimensions approx. 5.6 x 2.5 x 2.3 m, weight approx. 7.4 t. Scope of supply: new Siemens Sinumerik 840D sl control with Sinamics S120, air-conditioned switch cabinet manufactured in-house, direct measuring systems for X and Z, user-friendly interface, automatic B-axis, balancing and dressing (Marposs), machine enclosure with state-of-the-art safety technology, lubrication and hydraulic unit, new paint finish RAL 5015/7035, geometry inspection according to manufacturer's standard with protocol, operating manual. Options: internal grinding spindle, paper band filter with or without magnetic separator (Polo or Filtec), installation and commissioning, operator training.

Condition: like new (used), Year of construction: 2024, operating hours: 200 h, functionality: fully functional, grinding length: 600 mm, grinding width: 400 mm, workpiece weight (max.): 1,000 kg, grinding height: 430 mm, grinding wheel diameter: 405 mm, table load: 1,000 kg, grinding wheel width: 50 mm, spindle speed (max.): 2,500 rpm, spindle speed (min.): 500 rpm, grinding spindle motor power: 7,500 W, warranty duration: 12 months, input voltage: 400 V, Equipment: documentation/manual, rotational speed infinitely variable, Initial commissioning: 2024 Operating hours “grinding wheel in use” approx.: 100 hours The machine will be completely inspected by the manufacturer OKAMOTO and delivered with a geometry acceptance report. Manufacturer's warranty: 12 months Design: Column feed Control: Fanuc Screen: Touchscreen Workshop programming: for flat, slot, and step grinding (optional) Conventional operation of the machine possible (manual operation) Automatic multi-pass plunging Teach-in functions: Vertical, dressing, and reversing points Folding dresser with 3 diamonds next to the magnetic clamping plate Automatic compensation of the dressing amount Longitudinal guides: Double prism, hand-scraped with thermally symmetrical behavior, PTFE coated Maximum table load: 1,000 kg Hydraulic table drive X-axis Electric servo table drive Z-axis Electric servo grinding spindle drive Y-axis Travel in the longitudinal direction: 950 mm Travel in the transverse direction: 440 mm Travel table-new wheel (Ø 355 mm): 522 mm Grinding wheel standard: Ø355x38 mm Grinding wheel diameter max.: 405 mm Grinding wheel width max.: 50 mm Grinding wheel bore: Ø 127 mm Grinding spindle drive power: 7.5 kW Grinding spindle speed, infinitely variable: 500-2500 rpm Leveling screws and support plates Operating/programming/and maintenance manual, operating tool LED lamp Machine paint: Dark grey/silver structure Machine dimensions approx. LxWxH: 3,560 x 2,900 x 2,210 mm Weight approx.: 4,950 kg Connection value: 15 kVA Accessories: Folding dresser with automatic compensation Electro-permanent magnet, transverse pole: 800x400 mm, p=13 mm Band filter tank: 180 liters Coolant flushing gun Flanges 1 piece Grinding wheels 1 piece Commissioning and training by OKAMOTO is mandatory for warranty purposes All information is non-binding, subject to prior sale. The machines remain our property until full payment has been made. Our general terms and conditions apply. Delivery: ex works Delivery date: by arrangement (approx. 8 weeks) Prices: plus VAT Tjdpfx Ajz Hc Sdshmoc Payment terms: net, 10% with order, 90% before shipment Price for machine as understood is valid only in Germany. Other EU countries against a surcharge upon request. No export of the machine.

Condition: ready for operation (used), DAREX SP 2500 / Drill bit grinding machine incl. 3 inserts -CE marking -Clamping range (drill bits) 1.6 - 26 mm -Speed range 2850 / rpm -230 Volt version -Grinding wheels / CBN or diamond grinding wheels can be used -3 grinding inserts -Documentation Todpfez Evgxox Ahmec Dimensions: L x W x H 0.4 x 0.4 x 0.3 meters / Weight 80 kg Errors and omissions excepted.

Condition: ready for operation (used), Year of construction: 2004, operating hours: 2,184 h, functionality: fully functional, machine/vehicle number: 2407-463, spindle speed (max.): 60,000 rpm, number of spindles: 3, swivel angle B-axis (min.): -90 °, swivel angle B-axis (max.): 15 °, TECHNICAL DETAILS Grinding spindle speeds Spindle 1: 60,000 rpm Spindle 2: 60,000 rpm Spindle 3: 45,000 rpm B-axis swivel range: -90°/+15° MACHINE DETAILS Spindle hours Spindle 1: 11,278 h Spindle 2: 2,184 h Spindle 3: 2,841 h Main counter: 45,144 h EQUIPMENT Tedpfx Aextdfbohmsc Touch probe (on 4th spindle position)

Condition: used, Year of construction: 2022, Oscillating cylinder grinding machine from Ecoline. Technical specifications: A possible screw variant for tightening the spindle sleeve. A device similar to the ProLoc system is used. Todpewhqplsfx Ahmec Location: Nattheim.

Condition: used, Year of construction: 2022, Oscillating cylindrical grinding machine from Ecoline. Technical specifications: A possible screw variant for tightening the spindle sleeve. It uses something similar to a ProLoc device. Location: Nattheim. Tsdpewhqprjfx Ahmjc

Condition: used, Year of construction: 2017, grinding length 800 mm Tedjz Ebv Sopfx Ahmec grinding width 400 mm grinding height 375 mm dimensions of grinding wheel 300 x 50 x 76,2 mm max. table load 700 kg Condition: Used Accessories, tools, and clamping devices shown are included in the scope of delivery only if specified in the additional information. Subject to change, errors in technical data and specifications, and prior sale.

Condition: ready for operation (used), functionality: fully functional, Grinding length: 600 mm Grinding width: 250 mm Workpiece height: 450 mm Electromagnetic clamping table: 600 x 250 mm Grinding wheel diameter: 300 x 50 x 76.2 mm Tsdez Ayrvopfx Ahmec Spindle speed - stepless: 800 - 4200 rpm Total power requirement: 4 kW Machine weight: approx. 2.9 t