Used Atf Selective Soldering System for sale (46,925)

Condition: new, Leak detection device, electric, for fuel storage tank 400-1500 liters Pedpfx Ao Actuuei Tjgu · Mandatory requirement according to the German Water Resources Act (WHG) § 19 for the storage of used oils with a flash point >55 °C that previously belonged to hazard class A III (VbF). Design: electronic Suitable for: fuel storage tank 400-1500 liters.

Condition: new, Diesel fuel tank system Basic 1000l, H1800xW1200xL800mm, with pump and dispensing nozzle, CEMO * Complete with electric pump 230 V and automatic dispensing nozzle with nozzle holder * 4 m filling hose * With integrated collection basin * With optical leak indicator * Length: 800 mm Width: 1200 mm Podpfo Acq Uxsx Ai Togu Weight: 150 kg Flow rate: 56 l/min Capacity: 1000 l Equipment: with pump and dispensing nozzle Height: 1800 mm

Condition: new, Basic diesel fuel tank, 2500 liters, H1800 x W1200 x L1800 mm, with pump and dispensing nozzle, CEMO · Complete with electric pump, 230 V, and automatic dispensing nozzle with nozzle holder · 4 m filling hose · With integrated collection basin · With optical leak indicator · B Width: 1200 mm Weight: 235 kg Flow rate: 72 l/min Pgjdo Acq U Sopfx Ai Tou Capacity: 2500 l Height: 1800 mm Equipment: with pump and dispensing nozzle Length: 1800 mm

Condition: new, The Kipp-Stop system from Holzknecht is an active safety device for forestry winches, designed to prevent typical accidents caused by tipping, overturning, or rolling over of forestry towing vehicles with radio-controlled winches. The Kipp-Stop system can be retrofitted to any electro-hydraulic winch. A wiring diagram showing the socket assignment is included in the operating manual, allowing the system to be connected to any radio system. Winches equipped with this Kipp-Stop system stop the cable pull at the following values: Laterally left/right: 15° (tolerance +/- 3°) In the direction of travel uphill: 25° (tolerance +/- 3°) In the direction of travel downhill: 35° (tolerance +/- 3°) The specified inclination limits of the winch must not be exceeded. If the pull function is interrupted by the Kipp-Stop system when the above values are exceeded, the winch must be brought to a position at least 3° below the limit values in order to reactivate the pull function. By briefly activating the pull function three times, the system is disabled, meaning that a single pull can be performed even outside the above-mentioned limits. After that, the system is active again. Pedpfs Abntvex Ai Togu The Kipp-Stop system can be retrofitted to any electro-hydraulic winch. However, this device cannot guarantee complete protection against overturning! In particular, improper positioning of the towing vehicle (extreme slope, loose ground, etc.), interference from electromagnetic fields, and improper installation of the winch or the Kipp-Stop system can impair the function. The shield of the winch must be exactly vertical when the winch is lowered to the ground. When the Kipp-Stop system is installed, no hydraulic top link may be used!

Condition: new, mechanical quick-change device for heavy-duty vehicles. Pgedpfo Abnugex Ai Tju

Condition: new, H3000xB1 000xT300mm bolt-together shelving system, add-on shelf, 7 steel shelves, load capacity 150 kg, galvanized/azure blue, RAL 7035, SCHULTE · Fully bolt-together, quick-assembly shelving system in modular design · Sturdy, disassembled T-profile frame with bolt-together connecting plates, powder-coated Number of shelves: 7 Field load: 2300 kg Width: 1000 mm Surface: galvanized/azure blue, RAL 7035 Load capacity per shelf: 150 kg Depth: 300 mm Pgedps Ac Sp Dofx Ai Tsu Design: Add-on shelf Features: Steel shelves Height: 3000 mm

Condition: new, Bolt-together shelving system H2500xW1000xD400mm, add-on shelving unit, 6 steel shelves, load capacity 150 kg, galvanized/gentian blue, RAL 7035, SCHULTE · Fully bolt-together, quick-assembly shelving system in modular design · Sturdy, disassembled T-profile frame with bolt-together connecting plates, powder-coated Depth: 400 mm Type: Add-on shelving unit Field load: 1700 kg Number of shelves: 6 Load capacity per shelf: 150 kg Height: 2500 mm Surface: Galvanized/gentian blue, RAL 7035 Pgodpfe Ac Sqnex Ai Teu Width: 1000 mm Features: Steel shelves

Condition: new, H3000xB1 000xT400mm plug-in shelving system, basic unit, 7 steel shelves, load capacity 150 kg, galvanized/azure blue, RAL 7035, SCHULTE · Fully plug-in, quick-assembly shelving system with modular design Pgsdpfx Aj Ac Squji Teu · Sturdy, disassembled T-profile frame with plug-in connector plates, powder-coated Width: 1000 mm Number of shelves: 7 Field load: 2300 kg Design: Basic unit Load capacity per shelf: 150 kg Depth: 400 mm Surface: Galvanized/azure blue, RAL 7035 Height: 3000 mm Features: Steel shelves

Condition: new, H2000xB1 000xT500mm shelving system, basic unit with 5 steel shelves, load capacity 150 kg, galvanized/cyan blue, RAL 7035, SCHULTE · Fully plug-in, quick-assembly shelving system with modular design · Sturdy, disassembled T-profile frame, with plug-in connector plates, powder-coated Pgods Ac Sq Ijpfx Ai Tou Field load: 1300 kg Depth: 500 mm Width: 1000 mm Design: Basic unit Number of shelves: 5 Load capacity per shelf: 150 kg Surface: Galvanized/cyan blue, RAL 7035 Features: Steel shelves Height: 2000 mm

Condition: new, Bolt-together shelving system H2000xB1 000xT500mm, add-on shelving unit, 5 steel shelves, load capacity 150 kg, galvanized/gentian blue, RAL 7035, SCHULTE · Fully bolt-together, quick-assembly shelving system in a modular design · Sturdy, disassembled T-profile frame with bolt-together connecting plates, powder-coated Pgodj Ac Sq Uepfx Ai Tsu Depth: 500 mm Load capacity per shelf: 150 kg Height: 2000 mm Features: Steel shelves Number of shelves: 5 Field load: 1300 kg Width: 1000 mm Surface: Galvanized/gentian blue, RAL 7035 Design: Add-on shelving unit

Condition: new, H2000xB1 000xT300mm shelving system, basic unit, 5 steel shelves, load capacity 150 kg, galvanized/azure blue, RAL 7035, SCHULTE · Fully plug-in, quick-assembly shelving system in modular design · Sturdy, disassembled T-profile frame, with plug-in connector plates, powder-coated Field load: 1300 kg Width: 1000 mm Surface: galvanized/azure blue, RAL 7035 Depth: 300 mm Features: steel shelves Height: 2000 mm Number of shelves: 5 Load capacity per shelf: 150 kg Design: basic unit Pgodpfxe Ac Sn Tj Ai Tsu

Condition: new, Bolt-together shelving system H2500xB1000xT500mm, add-on shelving unit, 6 steel shelves, load capacity 150 kg, galvanized/gentian blue, RAL 7035, SCHULTE Pgjdpfx Ao Ac Srlei Teu · Fully bolt-together, quick-assembly shelving system in a modular design · Sturdy, disassembled T-profile frame, with bolt-together connector plates, powder-coated Field load: 1700 kg Width: 1000 mm Depth: 500 mm Surface: galvanized/gentian blue, RAL 7035 Number of shelves: 6 Features: steel shelves Height: 2500 mm Load capacity per shelf: 150 kg Design: add-on shelving unit

Condition: new, H3000xB1 000xT500mm shelving system, basic unit, 7 steel shelves, load capacity 150 kg, galvanized/azure blue, RAL 7035, SCHULTE · Fully demountable, quick-assembly shelving system in modular design · Sturdy, disassembled T-profile frame with demountable connector plates, powder-coated surface Surface: galvanized/azure blue, RAL 7035 Width: 1000 mm Depth: 500 mm Load capacity per shelf: 150 kg Height: 3000 mm Design: basic unit Pgedps Ac Srrofx Ai Tsu Number of shelves: 7 Features: steel shelves Field load: 2300 kg

Condition: new, H3000xB1 000xT500mm bolt-together shelving system, add-on shelf, 7 steel shelves, load capacity 150 kg, galvanized/azure blue, RAL 7035, SCHULTE * Fully bolt-together quick-assembly shelving system with modular design * Sturdy, disassembled T-profile frame, with bolt-together connector plates, powder-coated surface Surface: galvanized/azure blue, RAL 7035 Field load: 2300 kg Height: 3000 mm Number of shelves: 7 Load capacity per shelf: 150 kg Depth: 500 mm Pgeds Ac Srxopfx Ai Tju Design: add-on shelf Features: steel shelves Width: 1000 mm

Condition: new, H2000xB1 000xT600mm shelving system, basic unit, 5 steel shelves, load capacity 150 kg, galvanized/cyan blue, RAL 7035, SCHULTE · Fully demountable, quick-assembly shelving system with modular design · Sturdy, disassembled T-profile frame with demountable connector plates, powder-coated surface Surface: galvanized/cyan blue, RAL 7035 Features: steel shelves Pods Ac Sr Eopfx Ai Tsgu Design: basic unit Width: 1000 mm Height: 2000 mm Number of shelves: 5 Field load: 1300 kg Load capacity per shelf: 150 kg Depth: 600 mm

Condition: new, H3000xB1 000xT600mm shelving system, add-on shelving unit, 7 steel shelves, load capacity 150 kg, galvanized/gentian blue, RAL 7035, SCHULTE Psdpfj Ac Stvex Ai Tsgu · Fully demountable, quick-assembly shelving system in a modular design · Sturdy, disassembled T-profile frame, with demountable connector plates, powder-coated Depth: 600 mm Field load: 2300 kg Surface: galvanized/gentian blue, RAL 7035 Height: 3000 mm Features: steel shelves Width: 1000 mm Design: add-on shelving unit Number of shelves: 7 Load capacity per shelf: 150 kg

Condition: excellent (used), functionality: fully functional, total height: 850 mm, overall weight: 30 kg, includes reference block and battery charger, plus 1 measuring tip Pgedpo Adklmefx Ai Tsu in very good condition

Condition: new, 230V/5kVA, 10.8kWh, Lithium-ion NMC battery. Pedpfo Adln Nox Ai Togu

Condition: used, Nikon Type: VMZ-R3020 XYZ measuring ranges: 300 x 200 x 200 mm *TZ type with objective with low magnification: 250 x 200 x 200 mm Display resolution: 0.01 μm Maximum permissible deviation (MPE) EUX, MPE EUY, MPE 1.2 + 4L / 1000 µm EUXY, MPE 2.0 + 4L / 1000 µm EUZ, MPE 1.2 + 5L / 1000 µm Maximum sample weight 20 kg (Guaranteed accuracy: 5 kg) Camera Black and white / color 1/3 CMOS camera Working distance Pjdeyiy Hbspfx Ai Tjgu Type 1, 2, and 3: 50 mm Type 4: 30 mm Type TZ: (High magnification) 11 mm / (Low magnification) 32 mm Type A: 73.5 mm (63 mm with laser AF) Laser AF repeatability range 1), 3) 2σ ≦ 0.5 µm Illumination Type 1, 2, 3, and 4: Incident light, transmitted light, and 8-segment ring light with 3 angles of incidence *white LED / Type 4 has only 1 angle Type TZ: Left objective: Episcopic, dark field; Right objective lens: Incident light, transmitted light, dark field Type A: Incident light, transmitted light, and 8-segment ring light with 1 angle of incidence *white LED Power supply, power consumption AC100 V-240 V, 50/60 Hz / 4 A – 2 A Dimensions & weight Main body with table (W x D x H): 700 x 730 x 1793 mm / approx. 265 kg Controller: 190 x 450 x 450 mm / approx. 12 kg Footprint (W x D): 2700 x 2400 mm Condition: used Scope of delivery: (See picture) (Changes and errors in technical data are subject to change!) We would be happy to answer any further questions you may have by telephone.

Condition: used, Instrument Systems Instrument Systems LED Measurement Laboratory CAS140C, LEDGON 100, Integrating Sphere, Keithley 2611 – Complete System! For sale is a complete, professional LED measurement laboratory from Instrument Systems (Konica-Minolta Group). The system is suitable for the precise optical and electrical characterization of LEDs, LED modules, and small luminaires. All devices come from a laboratory environment, manufactured in 2007–2008, and represent high-quality industrial measurement technology. Scope / included components Pgedpfx Ajzimaasi Tou CAS 140C-152 Spectrometer (2008) Integrating Sphere ISP250-110 + ISP250-211 (2008) LEDGON 100 Goniophotometer (2007) CSD315 3-axis Controller + Emergency Stop Control Panel (2007) Keithley 2611 SMU / SourceMeter PC system including software: SpecWin Pro SpecWin Light Goniometer module Original license CDs User manual “LED test sockets” Cables & accessories as shown in the photos Technical features Measurement of total luminous flux (lumens) Spectral analysis (color temperature, CRI, xy, spectrum) Goniophotometric angular measurement Analysis of radiation patterns Electrical control and IV measurements with Keithley 2611 Fully automatic measurement sequences with SpecWin Pro CAS140C: approx. 36×15×30 cm / 7–9 kg Integrating Sphere: approx. 40×40×45 cm / 6–8 kg LEDGON 100: approx. 80×30×28 cm / 12–15 kg CSD315: approx. 42×12×35 cm / 5 kg Keithley SMU: approx. 36×9×28 cm / 5 kg Dimensions / weights (total approx. 40–45 kg) Important note: “The table shown in the photos is not included in the sale.” Condition: used Scope of delivery: (See image) (Changes and errors in the technical data are subject to change!) We would be happy to answer any further questions you may have by telephone.

Condition: used, SLM Solutions Type: SLM 280 HL For sale is a professional metal 3D printing system, type SLM 280 2.0, from SLM Solutions (Lübeck). The SLM is designed for 24/7 operation and was last used with titanium. Installation was in 2018. The system already has the sintering walls for gas flow. The system has only been operated with argon for the last 3 years. Approx. 50,000 laser hours. The 50,000 hours refer to the laser on-time; the exposure time is not recorded in the older 280 models. If I disregard the coating time, I estimate approximately 10,000 active laser hours. Last maintenance was in early 2026. Currently, occasional communication issues between the PC and the PLC are observed. In rare cases, this can lead to incorrect status messages, which can cause the system to be briefly interrupted during a running job. Technical data (excerpt) Pgodpfxezhlr Eo Ai Teu Single laser 400W Weight: 1,245 kg Build volume: 280 × 280 × 365 mm Laser: 1 × 400 W fiber laser (IPG) Optics: 3D galvo system Focus diameter: 80 – 115 µm Max. scanning speed: up to 10 m/s Layer thickness: 20 – 90 µm Minimum feature size: approx. 150 µm Build speed: up to approx. 113 cm³/h (material-dependent) Materials: Stainless steel, tool steel, titanium (Ti64), aluminum, Inconel, CoCr Inert gas: Argon Gas consumption process: approx. 2.5 – 8 l/min Gas consumption purging: approx. 70 – 110 l/min Compressed air: approx. 6 – 7 bar Electrical: 400 V, 3P+N+PE Fuse: 63 A Power consumption: approx. 3.5 – 5.5 kW Machine dimensions: approx. 2600 × 1200 × 2700 mm Weight: approx. 1300 kg (empty), up to approx. 1800 kg (including powder) Important note: "The table shown in the photos is not included in the sale." Condition: used Scope of supply: (See image) SLM 280 machine Control cabinet Process chamber Internal control panel with screen (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, VETTER Crane Technology PROFI Crane System / Two-Rail Portal Crane VETTER P300 PROFI Crane System Two-rail portal crane with crane bridge, manual travel unit, and electric chain hoist. For sale is a used VETTER PROFI crane system from the manufacturer Vetter Krantechnik GmbH. The system is suitable for assembly work, production, mechanical engineering, maintenance, logistics, as well as the safe lifting and positioning of heavy loads. Technical data Manufacturer: Vetter Krantechnik GmbH Type: P300 Design: PROFI crane system as a two-rail portal with crane bridge Year of manufacture: 2020 Load capacity: 1,600 kg Span of crane bridge: 5,100 mm Support distance L: 5,590 mm Support distance B: 5,100 mm Beam length: 6,170 mm Overall dimensions of the system: approx. 6,040 x 5,800 mm Bottom edge of crane bridge: 4,145 mm Bottom edge of portal beam: 4,567 mm Overall height: 4,905 mm Classification according to EN 15011: HC2 / S2 Steel structure group: 18/36/30 Operating voltage: 400 V / 50 Hz Control voltage: 24 V Max. permissible hoist weight: 85 kg Electric chain hoist Manufacturer: Vetter Krantechnik GmbH Type: SIXX8AF Year of manufacture: 2020 Load capacity: 1,600 kg Lifting speed: 4.0 / 1.0 m/min Lifting motor power: 1.50 / 0.37 kW FEM class: 2m / M5 Protection class: IP55 Duty cycle: 40 % Weight at 5 m lift: 65 kg Travel unit / trolley Manufacturer: Vetter Krantechnik GmbH Type: SiCO-HF 2000 A Pedpoz Sn Ddsfx Ai Tjgu Variant A Load capacity: 2,000 kg Beam width: 66 - 220 mm Weight: 17 kg Equipment Two-rail portal crane system Crane bridge Electric chain hoist SIXX8AF Manual travel unit SiCO-HF 2000 A Load hook Floor control Main switch Steel support and beam construction Inspection book available EC declaration of conformity available Documentation available Accessories according to pictures Application areas Mechanical engineering Assembly work Production Maintenance Workshop operation Material handling Logistics Longest component: approx. 6.2 m Heaviest single component: approx. 300 kg Total weight of the system is approximately between 2,000 and 3,500 kg, depending on the installed steel profiles and foundation plates. Condition Used Optical condition according to pictures System was installed and in operation Inspection book and documentation available Scope of delivery VETTER P300 PROFI crane system Crane bridge Electric chain hoist SIXX8AF 1.6 t Manual travel unit SiCO-HF 2000 A Support and beam construction Floor control / operating elements Main switch Inspection book EC declaration of conformity Documentation Accessories according to pictures The machines, tools and other items visible in the pictures, which are not explicitly described, are not included in the scope of delivery. Shipping or freight shipping possible. Subject to changes, errors and prior sale.

Condition: used, VETTER Krantechnik PROFI Crane System / Two-Rail Portal Crane VETTER P300 PROFI Crane System Two-rail portal crane with crane bridge, manual travel unit, and electric chain hoist For sale is a used VETTER PROFI crane system from the manufacturer Vetter Krantechnik GmbH. The system is suitable for assembly work, production, mechanical engineering, maintenance, logistics, as well as the safe lifting and positioning of heavy loads. Technical data Manufacturer: Vetter Krantechnik GmbH Type: P300 Design: PROFI Crane System as a two-rail portal with crane bridge Year of manufacture: 2020 Load capacity: 1,600 kg Span of crane bridge: 5,890 mm Support distance L: 5,590 mm Support distance B: 5,890 mm Beam length: 6,390 mm Overall dimensions of the system: approx. 6,590 x 6,590 mm UK crane bridge: 4,145 mm UK portal beam: 4,567 mm Overall height: 4,905 mm Classification according to EN 15011: HC2 / S2 Steel structure: 18/30/30 Operating voltage: 400 V / 50 Hz Control voltage: 24 V Max. permissible hoist weight: 85 kg Electric chain hoist Manufacturer: Vetter Krantechnik GmbH Type: SIXX8AF Year of manufacture: 2020 Load capacity: 1,600 kg Lifting speed: 4.0 / 1.0 m/min Lifting motor power: 1.50 / 0.37 kW Rated current: 7.7 / 5.4 A FEM class: 2m / M5 Protection class: IP55 Duty cycle: 40 % Number of load chains: 2 Weight at 5 m lift: 65 kg Travel unit / Trolley Manufacturer: Vetter Krantechnik GmbH Type: SiCO-HF 2000 A Variant A Load capacity: 2,000 kg Beam width: 66 - 220 mm Weight: 17 kg Equipment Two-rail portal crane system Crane bridge Electric chain hoist SIXX8AF Manual travel unit SiCO-HF 2000 A Load hook Pgedpfxjzgv U Ue Ai Tju Floor control Main switch Conductor rail / Power supply Steel support and beam structure Documentation / Crane test book available Hoist test book available EC declaration of conformity (crane) available EC declaration of conformity (hoist) available Assembly and operating instructions available Accessories as shown in the pictures Application areas Mechanical engineering Assembly work Production Maintenance Workshop operations Material handling Logistics Longest component: approx. 6.4 m Heaviest single component: approx. 300 kg Total weight of the system is approximately between 2,000 and 3,500 kg, depending on the installed steel profiles and foundation plates. Condition Used Optical condition as shown in the pictures System was assembled and in operation Test book and documentation available Scope of delivery VETTER P300 PROFI Crane System Crane bridge Electric chain hoist SIXX8AF 1.6 t Manual travel unit SiCO-HF 2000 A Support and beam structure Control / Operating elements Main switch Documentation / Test book EC declarations of conformity Assembly and operating instructions Accessories according to pictures The machines, tools and other items visible in the pictures, which are not explicitly described, are not included in the scope of delivery. Shipping or freight forwarding is possible. Subject to changes, errors and prior sale. We will be happy to answer any further questions by telephone.

Condition: used, KUKA Type: KR 10 R900 sixx / KRC4 KUKA industrial robot complete system Pjdsy Dt D Djpfx Ai Tsgu Robot: KR 10 R900 sixx Controller: KRC4 including KUKA smartPAD, cable set and accessories For sale is a KUKA industrial robot as a complete system from a commercial inventory. The system is ideally suited for automation tasks in industry, laboratories, assembly, handling, pick-and-place applications, testing tasks, and general robot applications. The 6-axis robot is designed for precise and rapid movements and can be used for gripping, positioning, feeding, moving, and processing components. The system offered consists of a robot arm, KRC4 controller, smartPAD, cables, and other accessories as shown in the pictures. Technical data: Manufacturer: KUKA Roboter GmbH Robot type: KR 10 R900 sixx Article No.: 10016515 Serial number: 500874 Payload: 10 kg Reach: 901 mm Axes: 6 Robot weight: 52 kg Controller: KRC4 Article No.: 11019802 Serial number: 224377 Controller weight: 33 kg Controller connection voltage: 1 x 230 V Mains frequency: 50/60 Hz Full load current: 12 A Mains fuse: 16 A Total system weight (approx.): 90–110 kg Robot dimensions (approx.): Reach 901 mm Controller dimensions (approx.): compact KRC4 design Software / Display according to system: KRC SR version: V8.2.3 HMI version: 8.2.0.4 B22 Base system: KSS 8.2.21_SR Installed options according to display: ExpertTech 3.1.1 Gripper-&-SpotTech 3.0.5 OrangeApps.MqttClient 2.2.12 Profinet KRC-Nexxt 2.2.7 RemoteService 1.0.2 UserTech 3.1.4 Description / Functions: The robot can be used for handling and automation processes, e.g. for gripping, transferring, feeding, positioning or processing workpieces. The 6 axes enable flexible movement in space. The compact design and the reach of 901 mm make the system particularly interesting for confined working areas and automated production cells. Total system weight (including controller and accessories, approx.): 90 – 110 kg Condition: used visually with typical signs of wear the screen and system information can be seen in the photos the visual condition can be seen in the pictures Scope of delivery: (See picture) KUKA KR 10 R900 sixx robot arm KUKA KRC4 controller KUKA smartPAD Connection and linking cables other accessories as shown in the pictures Important: The images are the only basis for the scope of delivery. "The table shown in the photos is not part of the sale." Commercial sale (Changes and errors in the technical data, information are subject to change!) We are happy to answer any further questions you may have by phone.

Condition: used, Year of construction: 1998, machine/vehicle number: 980919, functionality: fully functional, power: 5.5 kW (7.48 HP), input voltage: 400 V, input frequency: 50 Hz, volume flow: 3,450 m³/h, intake vacuum (max.): 3,550 mbar, suction capacity: 3,450 m³/h, intake manifold diameter: 250 mm, filter area: 23 m², total height: 2,959 mm, total length: 2,500 mm, total width: 1,238 mm, overall weight: 750 kg, Used clean air system for two to three woodworking machines operating simultaneously. Can be installed outdoors. New units can be installed upon request. The control system is equipped with a speed control function via a frequency converter. Psdpfxozukulj Ai Tsgu