Used Compacting- And Reducing Machine for sale (80,018)

Condition: used, Year of construction: 2023, operating hours: 1 h, MULAG Combination Mowing Device MKF 600 for Mounting on Unimog Mowing combination MKF600 consisting of: - Front boom mower MFK 500 - Verge mower MRF Base unit for single or dual-operator use, designed for front mounting plate size 5 with the following specification: Equipment Front Boom Mower MFK 500 * Designed for right-hand operation * Boom swivel range: 190 degrees * Hydraulically actuated collision protection with damping of the boom system via hydraulic accumulators * Hydraulic lateral shift of the boom by 1300 mm (in combination operation) / 1800 mm (in solo operation) * Float position of mowing units can be switched on/off * Quick-change device for mowing units * SAFETY STOP - Electric knife shaft on/off control from the operator panel, including brake valve * Operating hours counter * Proportional mlcontrol permanent hydraulics included * (CAN bus technology) for the boom, including dual-cylinder actuation (multiple functions may be performed simultaneously) * Boom relief regulation type AER with stepless ground pressure adjustment via potentiometer, can be switched on/off * Operator information system with TFT color display, including system monitoring and diagnostic support * Multifunction lever mlbasic single-handed control unit with multifunction lever (ergonomically designed for right hand use, 4 functions on one plane. All functions are proportionally controllable) * Combination control panel * Control of both units via multifunction control lever Nsdpj Abkhpsfx Ahbjdc * Oil cooling system with electric temperature monitoring included * Tool drive via front PTO * Hydraulic pump for 1st implement drive 62l / 340 bar * Hydraulic pump for 2nd implement drive 50l / 280 bar * Filled with Panolin HLP Synth, fully synthetic, rapidly biodegradable hydraulic oil * Telescopic boom system hydraulic adjustment for extending reach by 1,000 mm * Reach 6.50 m from vehicle center in combination operation * Reach 7.00 m from vehicle center in solo operation * 2-way electro-hydraulic switching valve controlled from operator panel (additional hydraulic dual functions) * Hydraulic rotation device for mowing implements, swivel range of 230°, operable from control panel. Boom side integrated, including quick-change plate * Hydraulic couplings: Quick coupling kit for flat-sealing quick couplers on mower * Cable set ES6 Front Unimog Connection of operator panel via universal electrical interface ES6 of Unimog * Hydraulic stabilizer legs included, 2 pieces, height adjustable * LED work lights, 2 pieces, mounted on boom * High-pressure water hose routing on boom Verge Mower MRF 350 consisting of the following configuration: Verge Mower MRF 350 * For right-hand operation * Reach 3.50 m from vehicle center * Hydraulic lateral adjustment of verge mower by 1000 mm (in combination operation) * SAFETY STOP - Electric knife shaft on/off control from the operator panel, including brake valve (knife shaft overrun limited to approx. 4 seconds) * Operating hours counter * Sensing automatic: control of the mowing head around obstacles. Mowing speed adjustment for evasive movement is steplessly adjustable by the operator at the control panel. * Single-hand operation unit with holder in Unimog Verge Mowing Head RMK 1200 * Working width: 1200 mm, Cutting thickness: max. 10 mm * MS-R blade * Knife shaft speed: approx. 3000 rpm * Standard sensing arm Mowing Head MK 1200 plus * Working width: 1200 mm, Cutting thickness:

Condition: ready for operation (used), grinding length: 2,500 mm, grinding wheel diameter: 750 mm, grinding diameter: 400 mm, distance between centers: 2,500 mm, spindle speed (max.): 360 rpm, spindle speed (min.): 25 rpm, workpiece spindle speed (max.): 360 rpm, Newall Cylindrical Grinder 400 x 2500mm Model: LA 96 Capacity: 400 x 2500mm Wheel Size: 75 x 750mm Work Head Speeds: 25-360 RPM Machine With: 2 Steadies Swivel Table Njdpsz S Nmyefx Ahbedc Coolant System

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, total length: 14,000 mm, total width: 4,500 mm, total height: 2,900 mm, overall weight: 12,000 kg, input voltage: 415 V, track width: 80 mm, input current: 70 A, input frequency: 50 Hz, Complete 2010 Rademaker Pie Line, capable of producing up to 5,280 filled savoury pies (with lids) per hour. Manufacturer - Rademaker B.V. Model - PIE LINE. Maximum mechanical speed – up to 22 strokes / minute. Output capacity – up to 5,280 pies / hour. Working width – 800mm wide. Electrical requirements – 415 V / 50 hz / 3 phase. Power – 70 Amps (approx.). Weight of complete line – 12,000 kg. Overall footprint – 14m long x 4.5m wide (including return conveyor) x 2.9m high. Line maximum width – 2.2m at widest point. Nsdpszvmy Hsfx Ahbodc This production line comprises of the following equipment/machinery: 1. 2 X sets of tooling complete with trollies – 1 X set for 4-across pies with casing diameter of 110mm and 1 X set for 3-across ‘family-style’ pies with casing diameter of 180mm. 2. Electrical control panel (with data plate ‘PIE LINE’ on). 3. Inclined flighted conveyor for loading of pastry sheets. 4. Overhead transfer conveyor (used to feed 'STRIPFEEDER') operating at 2.4m high along the length of the line. 5. Rademaker ‘STRIPFEEDER’ with denester for dropping pie cases. 5a. Rademaker Flour Sifter. 6. Rademaker Tamping unit (used to press / tamp the dough round into the pie casing). 7. Rademaker ‘DEPOSITOR’ 6-lane depositing system with hopper and pump. 8. Rademaker ‘SPRAYING DEVICE’. 9. Rademaker ‘LID DOUGH CONVEYOR’ for dropping lids onto filled pies. 10. Dutch Thermal Engineering b.v. (DTE) V-009.0 thermostat for regulating temperature of water bath sat under main conveyor holding pie casings. 11. Rademaker Press / Crimping unit / Marking unit for putting pattern into casing lid and ensuring it is secured onto pie. 12. Rademaker Pie Exit/Discharge conveyor. 13. Rademaker ‘DOUGH RETURN SYSTEM’ for excess pastry. 14. Rademaker ‘SPOT DEPOSITOR’ for 5-across over line depositing. 15. Unnamed egg-glaze mixing vessel and pump, mounted on mobile frame. CONDITION - Requires some reconditioning before entering production. NOTES – BUYER TO REMOVE FROM SITE.

Condition: like new (used), Year of construction: 2019, Weight 6250 kg Size 5810 × 2545 × 2445 mm Ndedevwdhhspfx Ahbsc Design Table clamping area 1500 x 600 mm Max. table load 1300 kg Longitudinal table movement 1600 mm Table groove (number/width) 3/ 16 mm Table feed 7 – 25 m/mm Min./Max. Distance spindle nose-table max. 600 mm Handwheel pitch vertical 0.002 mm Handwheel revolution vertical 0.5 mm Automatic grinding feed 0.002 – 0.02 mm Vertical rapid traverse (Y-axis) 230 mm/min Cross travel 660 mm Cross feed per stroke 0.1 – 12 mm Cross rapid traverse 1250 mm/min Handwheel pitch transverse 0.02 mm Handwheel revolution transverse 5 mm Grinding spindle motor 7.5 kW Grinding spindle speed 1450 rpm Grinding wheel 355 x 50 x 127 mm Hydraulic motor 3.7 kW

Condition: excellent (used), Year of construction: 2003, Degen FS 2550 Surface Grinding Machine Degen FS 2550 surface grinding machine, manufactured in 2003, in SUPER condition with approximately 100 operating hours. CE compliant!! The machine comes from the Richard-Hartmann School (vocational school) in Chemnitz. Technical data: Year of manufacture: 2003 Clamping area / table size: 500 x 250 mm Max. grinding area: 500 x 250 mm Max. travel (X / Z): 600 x 280 mm Max. distance between spindle nose and table: 490 – 500 mm Max. workpiece weight: 320 kg Dimensions of magnetic clamping plate: 500 x 250 x 80 mm Grinding spindle & feed Grinding wheel dimensions: 355 x 25 x 127 mm (standard) Spindle speed: 1,500 rpm (at 50 Hz) / 1,800 rpm Spindle motor: 2.2 kW (3 HP) Njdpfx Ahoz Rla Hebodc Longitudinal feed (X-axis, hydraulic): continuously variable 1 – 25 m/min Transverse feed (Z-axis, automated): 0.1 – 10 mm/ About the machine: Offered is a Degen FS 2550 surface grinding machine, manufactured in 2003, in SUPER condition with approximately 100 operating hours. This universal surface grinding machine is in very good original condition. It comes from a vocational school where it was used only sparingly for training purposes. It has a very easy-to-use control system. A grinding travel of 500 mm in the longitudinal axis and a transverse travel of 250 mm make it suitable for toolmaking, fixture construction, and small-series production. Its extensive standard equipment and ease of operation are characteristic of this series. The stable design of the spindle head and the guide principle with double V-guides in the longitudinal and transverse axes guarantee lasting precision. The intuitive operation of the controls simplifies operation and significantly increases productivity. The guides are regularly lubricated by the central lubrication system. The Degen has been mechanically and electrically tested by us. Take advantage of the opportunity to inspect and test the Degen on-site while it is powered up. You can find more surface grinding machines from well-known manufacturers on our website.

Condition: excellent (used), Year of construction: 2009, Geibel & Hotz FS 840 SD Surface grinding machine Geibel & Hotz FS 840 SD with B&R control, manufactured in 2009, in SUPER condition. CE compliant!! This machine comes from the training workshop of a renowned German mechanical engineering company. Technical data: Year of manufacture 2009 Max. grinding area (mm) 800 x 400 x 375 Travel in X (mm) 800 Travel in Y (mm) 400 Travel in Z (mm) 375 Clamping surface, magnetic (mm) 800 x 400 Grinding wheel (mm) 300 x 50 x 76.2 Power of grinding spindle motor (kW) 3.7 Grinding spindle speed (rpm) Njdjz Rmufopfx Ahbodc 1400 Manufacturer Geibel & Hotz Year of manufacture 2008 Control system B&R RPS Type of control system Cycle-controlled Total power consumption (kW) 12 kW Space requirement (mm) 3600 x 2750 x 2470 Weight (kg) 2700 About the machine: We offer a Geibel & Hotz FS 840 SD surface grinding machine with B&R control. This universal surface grinding machine is in very good, original condition. It comes from a company where it was only used to a small extent for training purposes. It has a very easy-to-use control system. A grinding travel of 800 mm in the longitudinal axis and a transverse travel of 400 mm make it suitable for toolmaking, jig and fixture construction, and small-batch production. The rich standard equipment and the simple operation of the machine are characteristic of this series. The stable design of the spindle head and the guide system with double V-guides in the longitudinal and transverse axes guarantee lasting precision. The intuitive operation of the control elements simplifies operation and significantly increases productivity. The guides are regularly lubricated by the central lubrication system. The Geibel & Hotz FS 840 SD has been mechanically and electrically inspected by us. Take advantage of the opportunity to inspect and test the Geibel & Hotz FS 840 SD on site under power. You can find more surface grinding machines from well-known manufacturers on our website.

Condition: new, Year of construction: 2026, travel distance X-axis: 2,800 mm, travel distance Y-axis: 1,900 mm, travel distance Z-axis: 1,500 mm, Machine configuration ROTAMILL 2819 - NC Rotary table, Ø1.800 mm - NC Fork-type Milling Head M-SERIES (A- and C-axis) - Milling spindle CST-42-180-S - Tool chain magazine, 54 pockets, HSK-A(T)63 - Chip conveyor - NC Control HEIDENHAIN TNC 640 - Technology package turning - 2-fold head change magazine, fully automated - Preparation of the machine for wet machining - Oil mist extraction unit, approx. 3.000 m³/h - Workpiece measuring touch probe BLUM TC 60 - Tool measuring, BLUM LaserControl Single NT - Kinematic 3D-calibration software - Heidenhain - Kinematic tool kid - CAD-Import (.step; .iges; .dxf) - Remote diagnosis (Teleservice) - Operator and maintenance training (1 day) excl. travel cost and expenses - Loading and (seaworthy) packing charges, FCA Jülich as per Incoterms 2020 - Installation and run-off inside Germany incl. travel costs and expenses OPTIONAL - Coolant unit Technical data - Traverses X-axis = 2,800 mm - Traverses Y-axis = 1,900 mm - Traverses Z-axis = 1,500 mm - Portal clearance (roof)- width (Y) = 2,250 mm - Portal clearance - height (Z) = 1,465 mm - Total weight, approx. = 41,000 kg - Feed rate in X, Y and Z = 50 m/min - Acceleration in X, Y and Z = 4 m/s2 - Feed force in X, Y and Z = 10.000 N Rotary NC-Table Ndedetwatdjpfx Ahbsc Rotary table (C1-Axis) - Face plate, standard = Ø 1,800 mm - Interference diameter = Ø 2,200 mm - Payload – milling, max. = 6,000 kg Drive C1-Axis – turning table HT - Swivel range = 360° (endless) - Rotational speed, max. = 30 rpm - Torque, max. = 7,473 Nm - Clamping moment = 13,000 Nm Fork type NC-Milling-Head M-SERIES (A-Axis) Drive A-Axis - Swivel range = ±110° (60 rpm) - Speed, max. = 100 rpm - Feed rate, max. = 600°/s - Nominal moment = 840 Nm - Clamping moment = 4,000 Nm Drive C2-Axis - Swivel range = ±360° - Speed max. = 65 rpm - Feed range, max. = 390°/s - Nominal moment = 1,020 Nm - Clamping moment = 4,000 Nm Milling spindle CST-42-180 S - Power, S1 (S6-40% ED) = 42 (53) kW - Nominal moment = 2,000 rpm - Torque, S1 (S6-40% ED), max. = 201 (253) Nm - Speed, max. = 12,000 rpm - Motor type = synchron/8-pole - Tool holder = HSK-A63 - Clamping system = hydraulic - Clamping force = 20 kN - Installation dimension, stator = Ø 180 mm - Spindle nose, length = 110 mm Accuracies according to VDI / DGQ 3441 - P (X,Y,Z) = 0,012 mm - P (C, A) = 5" - Ps (X,Y,Z) = 0,008 mm - P (C, A) = 3" Tool chain magazine with double arm gripper - Tool pockets = 54 - Tool holder = HSK-A(T)63 - Pocket distances = 110 mm - Tool diameter, fully loaded = Ø 105 mm - Tool diameter, max. = Ø 150 mm - Tool length, max. = 300 mm - Tool weight, max. = 8 kg Footprint & Weight - Length (X) = 6,830 mm - Width (Y) = 6,970 mm - Height (Z) = 5,150 mm

Condition: good (used), Second-hand machine in good condition Control type: Conventional active digital Location : 35708 Haiger Price : 13.500€ excl. Njdpsigv Ipjfx Ahbedc Technical data: Digital display 3-axis digital display HEIDENHEIN TNC 134 Travel X-axis 500 mm Travel Y-axis 350 mm Travel Z-axis 380 mm Tool holder Vertical milling head SK 40 with hydr. tool clamping DIN 2080 ring groove Table type Fixed table Table clamping surface 800 x 360 mm T-slot size 14 mm Weight 1,600 kg Dimensions 1500 x 2000 x 1900 mm Accessories - Central lubrication - coolant system - Operating instructions

Year of construction: 1987, condition: excellent (used), functionality: fully functional, 1987 Finzer ZUB 250 Multislide Punching & Forming Machine Used 1987 Finzer ZUB 250 multislide machine for sale. 250kN press unit, 6 forming slides, manual decoiler and 250mm feed. Very good condition. Manufacturer: Finzer Model: ZUB 250 Machine Type: Multislide Punching & Forming Machine Year: 1987 Condition: Very Good Machine Description The Finzer ZUB 250 is a heavy-duty mechanical multislide stamping, punching and forming machine designed for the high-volume production of complex components from strip and wire. This machine is equipped with a 250kN / 25-tonne press unit, a set of six forming slides and a manual decoiler, providing a versatile production system capable of combining punching, blanking, bending and forming operations within one production cycle. Multislide technology is particularly effective for components requiring several bends or forming operations from different directions. Compared with conventional single-slide power presses, the multiple independently arranged forming slides allow complex parts to be produced efficiently with reduced secondary operations. Main Specifications Manufacturer: Finzer Model: ZUB 250 Year: 1987 Machine Type: Multislide Punching & Forming Machine / Stamping & Bending Machine Press Capacity: Approx. 250kN / 25 tonnes Number of Forming Slides: 6 Maximum Feed Length: Approx. 250mm Maximum Strip Width: Approx. 60mm Maximum Wire Diameter: Approx. 3mm Forming Slide Capacity: Approx. 30kN per slide Forming Slide Stroke: Approx. 0–50mm Maximum Production Speed: Up to approx. 400 strokes/minute, depending on tooling, component and material Machine Weight: Approx. 4,000kg 250kN / 25 Ton Press Unit The machine incorporates an approximately: 250kN / 25-tonne press station The press operation can then be combined with movements from the surrounding forming slides to produce complex finished components in a continuous cycle. Six Forming Slides This Finzer is supplied with a complete set of six forming slides. Ndodpfx Ahsz S T Inebsc The multiple-slide arrangement is one of the main advantages of the ZUB system, allowing tooling to approach the component from several directions during the same production cycle. Forming capacity per slide: 30kN Slide stroke: Adjustable up to approximately 50mm The slides can be tooled for sequential bending, forming and positioning operations. Manual Decoiler Included The machine is supplied with a manual decoiler for coil-fed production. Coil & Strip Feed Capability Comparable Finzer ZUB250 machines are specified with: Maximum Strip Width: Approx. 60mm Maximum Wire Diameter: Approx. 3mm Maximum Feed Length: Approx. 250mm Feed length is typically adjustable to suit the individual component and tooling setup. High-Speed Production Depending on component design and tooling, period ZUB250 specifications quote operating speeds of approximately: 25–400 strokes per minute This makes the Finzer particularly suitable for repetitive, high-volume manufacture where several conventional press and forming operations might otherwise be required. Mechanical Cam-Controlled Multislide System The Finzer ZUB series uses a mechanically controlled cam-driven forming system. Cam-controlled multislide machines are particularly effective for repeat production because the motions of the forming tools can be precisely coordinated with the press and material feed.

Condition: used, Used machine Used Hettich Blue Max drilling and countersinking machine Motor power: 0.8 kW Motor speed: 2800 rpm 4 drilling spindles with longitudinal stops Njdpfxow I Um Tj Ahbjdc one foot switch Punch die is missing!! Availability: by arrangement Location: Solingen

Condition: like new (used), Year of construction: 2019, AMADA - LCG3015AJ – 2019, like new - Control system: AMADA - Fiber laser, 2100 W - Table size: 3000 x 1500 mm (x2) - Operating time: 300 hours Nsdpfxsiv S Nqj Ahbedc - Documentation available - Weight: 9400 kg - Operational Due to excessive administrative overhead (customs regulations), we do not deliver to Turkey, Iran, Russia, or Belarus.

Condition: excellent (used), Year of construction: 2010, Data: XYZ: 600/400/460 mm Spindle speed: 10,000 rpm Heidenhain TNC 620 control unit Spindle: SK 40 Internal coolant system: 20 bar CNC Nikken / 4-axis, D 200 mm Oil mist extraction system Chip conveyor Ndodpezw T R Uefx Ahboc

Condition: used, Doka-Framax Xlife formwork - New price: Net €514,000.00 - Starting price: €58,000.00 Nsdpfs Acf Umsx Ahbedc - Detailed information can be found under the photos.

Condition: good (used), Year of construction: 1989, grinding length: 400 mm, grinding width: 200 mm, Grinding area: 400 x 200 mm Magnetic area: 400 x 175 mm Vertical adjustment: 410 mm Grinding wheel dimensions: 225 x 25 x 50.8 mm Grinding wheel speed: 1420 / 2840 rpm Njdpfx Asv Tcy Ushbedc Complete with: - Coolant system - Hydraulic unit - Documentation Country of origin: Germany Motor power: 1.5 kW Machine dimensions (L x W x H): 2200 x 1500 x 2100 mm Machine weight: 1100 kg

Condition: new, number of aggregates 2 St. working width 2000-3500 mm work height max. 2450-3200 mm Wintech M9Cb Sealing Machine Automatic sealing system for wooden windows and doors with 2 processing units. For a detailed description, see the PDF document. ----- Manufacturer’s technical description: M9Cb robotic sealing system The machine comprises a robust structure made from aluminium profiles, fitted with motorised conveyor belts on which the window units are transported. The silicone is distributed evenly into the joint by means of two automatically controlled nozzles. The electronic control system, which is in constant communication with the sensor, determines the movement of the guns and the operating parameters. Technical data: Standard Optional Max. window width 2000 mm 3500 mm Max. window height 2450 mm 3200 mm Max. window thickness 160 mm 190 or 250 mm* Max. window weight 150 kg 200 or 400 kg* Loading station 2000 mm 3500 mm Unloading station 2000 mm 3500 mm Choice of silicone: Standard 1 colour 2 or 3 colours Master head 1 2 Sealing of timber panels no yes Formulation adapted to the type of elements no yes Synchronised conveyor belt no yes for heavy loads and/or conveying in both directions Double movable crossbar for flush-mounted hinged window sashes no yes *Please contact us for greater thicknesses or weights Optimisation of the sealing process: The M9Cb robotic sealing system revolutionises the sealing process by injecting exactly the right amount of silicone, thereby preventing unwanted streaks. It enables the glazing beads to be ‘nailed’ invisibly and saves the time required to cover the nail heads. The precision ensures high-quality, uniform sealing, which guarantees optimal watertightness whilst maximising the clarity of the units. With a feed speed of approx. 2 metres per minute, it offers fast and efficient processing on both sides simultaneously (on average 4 minutes per unit). More space available: No more lack of space in the workshop! The M9Cb operates vertically and Ndsdpfx Aozmy Ifohboc therefore takes up very little floor space. Leaning against a wall or partition, it frees up the space previously occupied by horizontal sealing tables. In addition, a strategically positioned conveyor belt can also serve as a vertical glazing table, thereby optimising the layout of the work area Automation of sealing: To ensure a seamless seal, it is no longer necessary to juggle the window unit or struggle with fitting seals. The M9Cb automates this laborious process on both sides Time savings: Thanks to the M9Cb, the workflow is no longer one-dimensional. Whilst the machine takes care of sealing the windows and doors, the operator can work on other tasks, e.g. glazing, blocking, packaging... This versatility enables the operator to diversify their activities and thus offers them a more rewarding experience. ----- ----- Price of the above machine on request! -----...

Condition: good (used), Year of construction: 2022, Brand: Dr. Boy GmbH & Co. KG Type: BOY 60E #55841 Year of manufacture: 2022 Operating hours: On request Screw diameter: 32 mm Maximum injection pressure: 2,142 bar Maximum shot volume: 100.5 cm³ Clamping force: 60 T Maximum distance between tie bars: 360 x 335 mm Minimum mold height: 250 mm Maximum distance between platens: 650 mm Electrical connection: 400 V / 50-60 Hz, 27.2 kVA Heating capacity: 8.4 kW Dimensions: 3,450 x 1,150 x 1,950 mm (L x W x H) Weight: 2,300 kg Ndsdpfx Ahsz Tiwhobsc Options: • Procan ALPHA 4 control system, 15" full-touch display • TEC Package 1: wear-resistant screw and barrel, ceramic heaters • Interface package including OPC-UA, Euromap 77 & 82 • Cooling circuits (3x) on both platens + 8-way water distributor • Oil filling (EconFluid, ISO-32)

Condition: used, Year of construction: 2004, functionality: fully functional, travel distance X-axis: 1,000 mm, travel distance Y-axis: 950 mm, travel distance Z-axis: 1,000 mm, controller manufacturer: Okuma, controller model: OSP E100M, workpiece height (max.): 1,000 mm, workpiece diameter (max.): 1,000 mm, workpiece weight (max.): 1,200 kg, total height: 3,280 mm, total length: 6,495 mm, total width: 3,460 mm, table width: 630 mm, table length: 630 mm, overall weight: 26,000 kg, spindle speed (min.): 50 rpm, spindle speed (max.): 12,000 rpm, coolant supply: 15 bar, number of slots in tool magazine: 60, Equipment: chip conveyor, We are pleased to offer this very well-maintained Okuma MA-600HB horizontal machining centre. The machine was manufactured in 2004 and is fitted with the OSP E100M control system. Technical specifications: Pallet table size: 630 x 630 mm Number of pallets: 2 Table load: 1200 kg Nodjz Tq Tkopfx Ahbodc Movement X-axis: 1000 mm Movement Y-axis : 950 mm Movement Z-axis : 1000 mm Table indexing: 360 x1 ° Spindle Taper: MAS BT50 Spindle speed: 12.000 1/min Spindle motor: 37/26 kW Magazin capacity: 60 We realise that you may wish to receive further information or view the machine. In that case, please contact us, providing your company details so that we can get in touch with you.

Condition: excellent (used), Year of construction: 2017, Technical specifications: 2 rollers hydraulically adjustable 3 rollers driven Shaft diameter: 80 mm Lateral, hydraulically controlled arm correctors on the left and right Ndodpfx Ao Afby Dehbsc CE marking Bending capacity, square bar: 60 x 60 x 3 mm Bending capacity, flat bar: 100 x 20 mm Bending capacity, tube: 88.9 x 4 mm Bending capacity, angle: 70 x 70 x 8 mm Round bar: 40 mm Motor power: 4.75 kW Control panel with digital display Dimensions (length x width x height): approx. 1650 x 1450 x 1550 mm Weight: approx. 1.6 tons The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: like new (used), Year of construction: 2018, Technical data: Travel ranges (X/Y): 300 / 200 mm Travel range (Z): 350 mm Diagonal travel range (W): 200 mm Table size: 350 x 250 mm Max. workpiece height: 180 mm Nodpfx Ahe Afbykobjdc Max. workpiece weight: 150 kg Electrode diameter: 0.2 – 3.0 mm Dimensions (length x width x height): approx. 1100 x 1100 x 2000 mm Machine weight: approx. 0.6 tons The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear correspond to its age; used machines are sold without any warranty.

Condition: excellent (used), Year of construction: 2001, 1,000 shots used injection molding machine with robot, safety fence, and conveyor belt Manufacturer: DEMAG Type: ERGOTECH100/420-430System Year of manufacture: 2001 Clamping force: 100 tons Tie bar distance: 400 x 400 mm Screw diameter: 35 mm Max. injection volume: 168 cm³ Shot weight: 150 g/shot Control system: NC4 Equipment: - Robot, Engel, Type: W711-0174, Year of manufacture: 2009 - Safety fence - Conveyor belt - 2 x core pull - Blow valve Ndedpfxs Afbx Te Ahbec

Condition: ready for operation (used), Year of construction: 2005, functionality: fully functional, type of input current: three-phase, !! This machine comes with a donor machine that can be used for spare parts. !! The Nordson FoamMelt 200 (FM 200) is a specialized dispensing system that mixes hot melt adhesives with an inert gas (such as nitrogen) to create a closed-cell foam. This process reduces adhesive consumption by as much as 50% to 65% while improving bond performance. Applications: Widely used for bonding, sealing, gluing, and gasket making in the automotive and packaging industries. Ndsdpjy N Ahcofx Ahboc Benefits of FoamMelt Technology Faster Curing: The foam cools down faster, enabling higher production speeds. Better Filling Properties: The volume increase due to the gas makes it ideal for filling gaps. Improved Safety: The lower heat density of the foam reduces the risk of burns for operators.

Condition: used, Year of construction: 2008, travel distance X-axis: 630 mm, travel distance Y-axis: 620 mm, travel distance Z-axis: 710 mm, controller manufacturer: Fanuc, controller model: 160iS-MB, total height: 2,771 mm, total length: 5,855 mm, total width: 2,555 mm, table width: 500 mm, table length: 500 mm, table load: 400 kg, overall weight: 820 kg, spindle speed (min.): 1,000 rpm, spindle speed (max.): 12,000 rpm, spindle nose: Mas BBT 40, number of slots in tool magazine: 60, Equipment: chip conveyor, CNC Horizontal Machining Center OKK HP 500S Ndjdpfo Aawapjx Ahbsc Technical details: CNC Control Fanuc 160is-MB Pallet table size 500 x 500 mm Number of pallets 2x Table load 400 kg X-axis travel: 630 mm Y-axis travel: 620 mm Z-axis travel: 710 mm Indexing of table 0,001° Spindle holder MAS BBT 40 Spindle speed 100 - 12.000 rpm Spindle motor 11/7,5 kW Positions in the tool magazine 60 If you have any questions concerning the machine, please do not hesitate to contact us by phone or e-mail. Feel free to view our other advertisements for a complete overview of our stock. We sell this machine at a special price called “as seen”. This means that we do not check the condition of the machine.

Condition: like new (used), Year of construction: 2018, operating hours: 240 h, functionality: fully functional, travel distance X-axis: 460 mm, travel distance Y-axis: 460 mm, travel distance Z-axis: 410 mm, feed rate X-axis: 48,000 m/min, feed rate Y-axis: 48,000 m/min, feed rate Z-axis: 48,000 m/min, controller manufacturer: siemens 828D, controller model: 828D, total height: 2,602 mm, total length: 3,350 mm, total width: 2,265 mm, table width: 320 mm, table length: 320 mm, table load: 250 kg, rotational speed (max.): 200 rpm, overall weight: 6,200 kg, spindle speed (max.): 18,000 rpm, coolant supply: 20 bar, distance table center to spindle nose: 60 mm, spindle motor power: 23 W, spindle nose: hsk63, number of spindles: 1, number of slots in tool magazine: 40, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, Due to the cessation of business operations, we are offering this like-new Hardinge H320 horizontal machining center, manufactured in 2018. Model: H320 Serial number: GHLB7G0001 Date of manufacture: 05/31/2018 Supply voltage: 400 V Ndjdpfx Ahs Aazdxobec Number of phases: 3 Weight: 6200 kg Cooling on the ball screw spindles Spindle cooled Glass scales on all axes High-speed 4th axis with direct drive motor, 200 rpm Scraper chip conveyor It is also possible to take over the tool holders and machine clamps. If you have any questions or would like more information, please feel free to send us a message or call us.

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, machine/vehicle number: 221363, working width: 400 mm, passage height: 250 mm, total length: 1,300 mm, total width: 1,070 mm, total height: 1,450 mm, height adjustment type: mechanical, overall weight: 600 kg, working height: 900 mm, compressed air connection: 6 bar, extraction nozzle diameter: 100 mm, type of input current: three-phase, power: 8.73 kW (11.87 HP), input voltage: 400 V, input frequency: 50 Hz, workpiece height (max.): 250 mm, workpiece width (max.): 400 mm, empty load weight: 580 kg, input current: 16 A, Equipment: emergency stop, rotational speed infinitely variable, This used cross-cutting machine, equipped with one brushing unit, is designed for creating textures on wooden surfaces. The combination of the cross-cutting unit and the brushing unit allows for the creation of various effects, including authentic band saw textures and other natural surface patterns. The machine features a TAP function that enables the application of a random effect to the workpiece. This is achieved using five separate tapping heads above the sanding belt. A compressed air connection is required for the operation of this function. By adjusting the transport speed, the settings of the cross-cutting unit, and the brushing unit, the intensity of the process can be easily controlled. This allows for the creation of a wide range of textures and finishes, depending on the desired end result. The machine is suitable for processing various wooden products, including wooden floors, wall panels, furniture components, doors, and other wooden products where a distinctive surface texture is desired. This particular machine is offered as a used machine, is in very good condition, and is immediately available. For additional information, technical specifications, or photos, please contact us. Nodpfs Aazymex Ahbodc

Year of construction: 2021, condition: used, functionality: fully functional, T-nut inserting machine for Large Flange T-nuts Ndjdpezbu R Esfx Ahbjc