Used G120D Power Module Pm250D for sale (39,090)

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,250 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, power: 22 kW (29.91 HP), year of last overhaul: 2025, volume flow: 530 m³/h, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the whirling unit replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced Kdjdpjy R Npijfx Afvol All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Various pistons / cylinders available. Cevoman bvba. Kodpfjy R Nu Eox Afvedl Lenskensdijk 5 2200 Herentals Belgium

Condition: excellent (used), Year of construction: 2008, operating hours: 8,948 h, functionality: fully functional, spindle speed (max.): 9,500 rpm, feed length X-axis: 470 mm, feed length Y-axis: 330 mm, feed length Z-axis: 660 mm, type of input current: three-phase, grinding wheel diameter: 200 mm, overall weight: 4,500 kg, grinding length: 350 mm, feed rate X-axis: 15 m/min, feed rate Y-axis: 15 m/min, feed rate Z-axis: 15 m/min, grinding spindle motor power: 11,500 W, input voltage: 400 V, year of last overhaul: 2026, CNC Tool grinding machine WALTER Helitronic Power TECHNICAL CHARACTERISTICS: Year of manufacturing: 2008 CNC control: FANUC Series 31i-model A5 Software installed: Tool Studio 3 Number of axes: 5 Height of centers: 145 / 190 [mm] Stroke X axis: 470 [mm] Rapid traverse rate X axis: 15000 [mm/min] Stroke Y axis: 330 [mm] Rapid traverse rate Y axis: 15000 [mm/min] Stroke Z axis: 660 [mm] Rapid traverse rate Z axis: 15000 [mm/min] Stroke A axis: 360 [°] Stroke C axis: +/- 200 [°] Max. workpiece lenght : end face grinding: 280 [mm] Max. grinding lenght: 350 [mm] Max. grinding diameter: 320 [mm] Max. grinding wheel speed: 9500 [rpm] Grinding spindle motor power: 11.5 [kW] Max. diameter grinding wheel: 200 [mm] Number of hours under power: 8948 [h] Coolant pump pressure: 7 [bar] Collant pump flow rate: 120 [l/min] Lubrication tank capacity: 400 [l] Supply voltage: 400 [V] Kodpfxjy Sxrpe Afvsdl Total power required: 25 [kVA] Weight: 4500 [Kg] INCLUDED EQUIPMENT: x1 TOOLSTUDIO 3 software x1 direct-drive A axis (Hollow Shaft) x1 automatic tool clamping system x1 RENISHAW LP2 part probe x1 DSL Air Technology type AES-GAMMA 30 mist extractor x1 lubrication tank + paper filtration system x1 GRUNDFOS coolant pump x35 grinding wheel holders (equipped with CBN wheels) x22 ISO50 attachments x1 SCHUNK collet holder x22 collets x1 NIKKEN collet holder x13 NIKKEN collets x1 metal rack for grinding wheel holders and ISO50 attachments 1x ISO50 calibration mandrel intended for axis calibration 1x calibration disc intended for axis calibration x1 set of service wrenches Various technical manuals Machine visible under power in our premises by appointment. Price on request, loading on truck included. Possibility of shipping Worldwide. The information on this page has been obtained by the best of our ability. Therefore, its accuracy can not be guaranteed. Machine for sharpening tools, milling cutters, taps, and drills. Machine similar to brands such as Blohm, Elb, Ewag, Favretto, Fenix, Ger, Jones & Shipman, Jung, Karstens, NUMAFFUT, Okamoto, Okuma, Saacke, SMP, Studer, Vollmer, Walter. Also see cylindrical or surface grinding machines, lathes, machining centers, and milling machines.

Condition: new, Year of construction: 2023, Year of manufacture: 2023 General condition: very good Technical condition: very good Visual condition: very good 4 x HMF 2320K-RCS K6 MOBILE CRANES 2023 (NEW) Electronic speed adjustment, HDL-d Fly brake control Progressive crane control Priority flow control Kdsdpfswlhgisx Afvel Dual Power plus articulated boom system Proportional control valve PVG 32 Internal hose routing Environmentally friendly high-quality coating RCL safety system 5-6 functions available Winch ready Radio remote control

Condition: used, Year of construction: 2010, functionality: fully functional, Fröhling wood chip system, 500 kW, including buffer tank. Pusher-type discharge system for feeding the system. Automatic filling and gasification system (2 years old). Kedpoy Ti Evsfx Afvjdl Network pump including control unit for district heating network. Price negotiable.

Condition: new, Year of construction: 2025, Plasma cutting machine for pipes and profiles Kdsdpfxjgu Nmhs Afvol Plasma cutting machine for cutting pipes and profiles. The cutting contour is defined and create by the software. The created CNC code can send to the machine via USB or network. The program can be easily choose via the 12"touch display. The automatic cutting process is started after manual insertion of the workpiece. - Tube length: max. 6000mm - for round tube up to OD = 150mm max - for square tube up to 101.6x101.6mm (4 "x4") max - maximum pipe weight 100KG per load - 4-jaw chuck - 1x automatic raw support - fully automatic cutting process - PC control with 12 "touch display - Data import via USB and network - Power consumption: 400V 3P 2KW - weight: 800KG Made in Germany The pictures show you an older machine

Condition: used, Lot of office containers / sanitary containers (quantity: 19) - KECO Module Ksdpfx Afoy Sn Nqevjdl

Condition: used, Year of construction: 2013, functionality: fully functional, machine/vehicle number: 2123083B, total height: 560 mm, total width: 500 mm, total length: 580 mm, input voltage: 230 V, temperature: 1,600 °C, input current: 25 A, input frequency: 50 Hz, overall weight: 65 kg, Professional Schultheiss VPC 040 power induction casting machine, manufactured in Germany. High-performance, compact benchtop unit designed for producing top-quality, high-detail castings in gold, silver, and other precious metal alloys. The "Power" version offers increased capacity and faster cycle times compared to the standard model. It features a fully automated, one-button vacuum and pressure application system to ensure exceptional alloy homogeneity and minimal porosity. Kdsdpfx Afjy Tbfzevsl Key Features: - Fully Automatic Control: 12-step digital casting programs for consistent results. - Advanced Induction Technology: Fast, gentle heating with a mixing booster effect. - Single Phase Convenience: Operates on standard 230V power. - Versatile: Capable of handling fine filigree details and larger solid pieces. Technical Specifications: - Manufacturer: Schultheiss GmbH (Germany) - Type: VPC 040 Power - Year of Manufacture: 2013 - Serial Number: 2123083B - Max. Temperature: Up to 1,600°C - Max. Flask Size: Ø 100 mm x 120 mm - Power: 5 kVA / 25 A (Single Phase, 230V) - Dimensions: 500 x 580 x 560 mm - Condition: Used, visually excellent and clean. Rear ports include Water Inlet/Outlet, Vacuum, and Pressure Gas.

Condition: ready for operation (used), Year of construction: 2011, operating hours: 56,000 h, functionality: fully functional, type of input current: AC, power: 10,000 kW (13,596.20 HP), input voltage: 11,000 V, fuel: domestic gas H, Equipment: documentation/manual, 5 CHP units of 2 MW each with Caterpillar engine generator sets, each rated at 2.5 MVA, 10.5 kV generator output, operating hours range from 26,000 to 54,000. Fuel types: natural gas and methane. The units have been decommissioned and fully preserved by the operator. Each unit comes as a complete small building, including heat extraction systems. Full documentation and maintenance records are available. Site inspections can be arranged at short notice. Kdsdpfxoy R Ebbo Afvel Available until late 2026 from Western Europe. The units are immediately ready for relocation, with dismantling to be carried out by the buyer. Asking price: €1,459,000 (USD 1,699,000) for all 5 units. The units will be sold as seen and must be relocated from the site by the buyer.

Condition: new, Edgebanding Machine HOLZ-HER 1308 XL AURIGA POWER -Showroom machine- Innovation: GLUJET GJ725 This offer concerns an equipment package. The following components and options are already included in the price: - Extendable workpiece support - Edge Control PPC 322 W control system - ECO MODE energy-saving mode - Jointing cutting unit FG201 with 2 milling heads - Diamond milling cutter Ø 70 x 64 x 30 mm, Z2+2, left-hand rotation - Diamond milling cutter Ø 70 x 64 x 30 mm, Z2+2, right-hand rotation - Edge feed 1903 - Glue application system Glu Jet GJ725 NC PUR PRO - Pressure unit 1912-3 pneumatic - End trimming unit 1918 pneumatic 60 mm - Multifunctional milling unit FR301 MOT6 - Diamond milling cutter Ø 56/60 mm, left-hand rotation - Diamond milling cutter Ø 56/60 mm, right-hand rotation - Corner rounding unit FF301 MOT1 - Scraper unit ZK301 MOT4 incl. high-gloss package - Carbide reversible knives for scraper carrier - Chip collection box for scraper unit - Buffing unit 1940 - Spray device TR301 for infeed and outfeed areas - Motorized pressure bridge adjustment - iTronic-adaptive pressure and glue quantity control - Extended infeed fence 1,252 mm Kdjdpfx Aju R Sy Aofvjl - Motorized adjustment for infeed fence - Pressure unit DW301 with motorized NC axis - Extraction hoods for end trimming unit 1918 - Shelving program - Surface scraper FK701 - Spray device GM301 after the pressure unit - new showroom machine -

Condition: used, Year of construction: 2013, functionality: fully functional, power: 7.5 kW (10.20 HP), input voltage: 400 V, input current: 13 A, input frequency: 50 Hz, type of input current: three-phase, volume flow: 5,089 m³/h, suction capacity: 5,089 m³/h, intake manifold diameter: 300 mm, actuation type: electric, overall weight: 972 kg, We are offering this used AL-KO POWER UNIT 300 P mobile extraction system, year of manufacture 2013. The extraction unit is in good condition and was kept in a heated room. The filters are clean and can be easily shaken off. Type: POWER UNIT 300 P Serial number: 2433358790 Year of manufacture: 2013 Suction nozzle: 300 mm Rated speed: 2,895 rpm Kdodey Akfpepfx Afvel Rated air flow: 5,089 m³/h Rated current: 13.8 A Negative pressure at rated air flow: 2,050 Pa Protection class: IP 54 Motor power: 7.5 kW Weight: 972 kg Voltage/phase/frequency: 400/3~/50 Hz Max. compressed air connection: 8.5 bar Fuse: 25 A Filter number: 85101201 Filter category: Cat. M automatic gate/slide valve control If you have any questions or need further information, feel free to send us a message or call us.

Condition: used, Year of construction: 2010, operating hours: 13,800 h, power: 1,600 kW (2,175.39 HP), For sale are 3 MTU cogeneration modules / CHP plants manufactured by MTU Onsite Energy GmbH, model AoE16V4000L62, year of manufacture 2010. These plants are ideally suited for decentralized energy generation and combined heat and power (CHP) applications. Technical specifications (per documentation): * Electrical output: 1,600 kW * Thermal output: 1,746 kW * Gas power: Pgaz PCS 4,579 kW / Pgaz PCI 4,121 kW * Voltage / Frequency: 400 V / 50 Hz Operating hours: * GE1: 42,479 h * GE2: 13,800 h * GE3: 43,397 h The scope of supply, as per documentation, includes a comprehensive range of auxiliary equipment and system components, including: roof-mounted air cooler, auxiliary cabinet, control cabinet, exhaust heat exchanger, water heat exchanger, pipework and ducts with chimney, oil storage room with 3 tanks and piping, as well as electrical cabling. Ksdpfx Afoyt H H Nevodl These plants represent an attractive solution for operators, resellers, and projects in the fields of energy supply, industry, or for spare parts recovery.

Condition: used, length ~ 450 mm width ~ 650 mm height ~ 1.100 mm Battery-powered hand strapping tool BW-03 with 2 x battery, charger and Cyklop dispenser and 2.5 rolls of strapping. Kdedpfx Asx R Ttljfvol

Condition: used, Pressure: 100 bar Kdodpfx Afswdun Djvel Capacity: 2 L Motor: 0.75 kW

Condition: used, Three-phase power meter: current, voltage, and power measurement; long-term monitoring; energy measurement 3-phase power measurement device, ammeter, voltmeter, digital measuring instrument, active power, apparent power, reactive power BEHA Type UNITEST Power Analyzer 93555 For measuring voltage, current, active power, apparent power, reactive power, power factor, phase angle, frequency measurement, phase sequence detection, energy measurement, and harmonics measurement. Display: LC multifunction display with backlight Refresh rate: approx. 2 sec. Data logger: 512 KB non-volatile memory (max. 21,000 readings, max. 10 data sets) Sampling rate: 5 s, 30 s, 1 min, 2 min. (adjustable) Data transmission: via optically isolated RS232 interface Manual memory: max. 99 measurements Overvoltage category: CAT III 600 V Power supply: 8 x 1.5V AA batteries or mains adapter 230VAC / 12VDC (batteries not included) Voltage measurement: 3 input channels with common reference point "N" Measuring range: 0 - 600 V RMS Display range: 0 - 999.9 V RMS Resolution: 0.1 V Mains frequency: 50 Hz Current measurement: Measuring range Input I1, I2, I3: 3 - 999.9 A Input I4: 3 - 250 A Display range: 0 - 999.9 A Resolution: 0.1 A Clamp opening: 40 mm Kdsdpfx Ajx A Imzefvol Active power: Selectable display of the active power of an individual input or the total value Display range: 0 - 999.9 kW Resolution: 0.1 kW Apparent power: Calculated from the RMS values of voltage and current Display range: 0 - 999.9 kVA Resolution: 0.1 kVA Frequency measurement: Range: 45...80 Hz Resolution: 0.1 Hz Accessories: - Carrying case - Operating manual - 4 measuring clamps - 4 test leads with crocodile clips - RS232 adapter cable - Mains adapter 230VAC / 12VDC Overall dimensions (W x H x D): 370 x 270 x 170 mm Total weight: 3 kg Device tested, fully functional. Note: The housing of 2 measuring clamps is damaged and the battery compartment shows some oxidation (see photos).

Condition: like new (used), Year of construction: 2021, functionality: fully functional, machine/vehicle number: 30160328026, power: 210 kW (285.52 HP), rotational speed (min.): 1,500 rpm, type of cooling: water, nominal power: 210 kW (285.52 HP), This CHP unit comes from an investment that was never put into operation. Kjdpfx Aeyzcxrefvjdl

Condition: used, Year of construction: 2018, machine/vehicle number: 213357, Own weight: 710 kg, Power: 20 kVA Kodpfjy Rvrkjx Afvjdl

Condition: used, mileage: 4,500 km, power: 120 kW (163.15 HP), first registration: 01/2026, fuel type: electric, color: grey, gearing type: automatic, suspension: other, number of seats: 5, Equipment: ABS, air conditioning, airbag, central locking, cruise control, electronic stability program (ESP), immobilizer system, navigation system, onboard computer, sliding door, traction control, Roadworthy, electric, lumbar support, accident-free, demonstration vehicle, 360-degree camera, metallic paint, 5-door, single owner, front-wheel drive, green emissions sticker (4), leather, navigation pre-installed, lithium-ion battery, bidirectional charging, park-out assist, wireless charging for smartphones, fully digital instrument cluster, Apple CarPlay, Android Auto, distance warning system, grey color, passenger airbag, front side airbags, electrically adjustable comfort seats, ventilated seats, ventilated front seats, height-adjustable front seats, right sliding door, left sliding door, leather steering wheel, LED headlights, automatic lights, keyless entry/start (Keyless-Go), parking sensors front and rear, rear-view camera, daytime running lights, rain sensor, voice control, blind spot assist, LED daytime running lights, digital radio, traffic sign recognition, emergency call system, digital speedometer, hill-start assist, tire pressure monitoring, Linguatronic, traction control, electronic traction system, electric windows, heated seats, rear seat heating, phone preparation, hands-free system, Bluetooth hands-free system, multifunction steering wheel, electric tailgate, radio, radio/MP3, MP3 interface, USB port, tinted windows, folding exterior mirrors, heated exterior mirrors, auto-dimming interior mirror, auto-dimming mirrors, heated steering wheel, power steering, non-smoker vehicle, electric exterior mirrors, alarm system, speed limiter, adaptive cruise control, ISOFIX child seat mount, split rear bench seat, alloy wheels, all-season tires, adjustable steering column, luggage compartment cover, center armrest, lane change assist, lane keeping assist, drowsiness detection, electric parking brake, automatic transmission, technology: onboard computer, fully digital instrument cluster, bidirectional charging, assistance systems: blind spot assist, drowsiness detection, traffic sign recognition, rain sensor, light sensor, hill-start assist, lane keeping assist, lane change assist, adaptive cruise control, park-out assist, distance/collision... Kodpfx Afey R Titovsdl

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. Kodpfx Afefz Ndyevodl There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. Kdsdpjflrc Sofx Afvsl ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. Kdodpefz A H Dsfx Afvol

Condition: ready for operation (used), Siemens 6SL3120-1TE24-5AC0 Single Motor Module 45A Version: C SN:T-P36206521, as good as new, never in use, 100% functional, scope of delivery as per photos, the agreed sales discounts do not apply to this article. Please ask for price separately! Kdsdpfexag Urex Afvjl

Condition: ready for operation (used), Veeder-Root TLS-350 4-Input Probe Thermistor Module 330724-001, used, normal signs of use, 100% functional, scope of delivery as per photos Kedpoxaifgefx Afvsdl

Condition: good (used), functionality: fully functional, roll diameter: 50 mm, roll width: 600 mm, roll pitch: 90 mm, total width: 685 mm, total height: 150 mm, total length: 1,980 mm, conveying length: 1,980 mm, construction width: 685 mm, construction height: 150 mm, input voltage: 24 V, overall weight: 60 kg, TAF item number: 1000005971 Manufacturer: TAF-Industriesysteme Year of manufacture: unknown Overall dimensions (LxWxH) in mm: 1,980 x 685 x 150 Width including side rail in mm: 685 Side rail height in mm: 140 Conveyor length in mm: 1,980 Conveyor width in mm: 600 Conveyor height in mm: 150 Roller pitch in mm: 90 Substructure: not available Support roller axle type: M8 internal thread Support roller diameter: 50 mm Support rollers per axle: 1 Support roller material: Steel Drive: Kyowa Puls Roller Motor type: Puls Roller Motor data: / Conveyor speed in m/s: 35 ZMHT, 0.83 m/s Kdjdpfxey R R I Hs Afvjl Net weight in kg: 60 Condition: used / fully functional Functional test: OK

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, operating hours: 4,500 h, input voltage: 400 V, travel distance X-axis: 700 mm, number of slots in tool magazine: 21, controller manufacturer: fanuc, controller model: 31i model B5, rapid traverse Z-axis: 60 m/min, rapid traverse X-axis: 60 m/min, rapid traverse Y-axis: 60 m/min, spindle nose: BT 30 big plus, spindle speed (max.): 10,000 rpm, operating hours of spindle: 4,500 h, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, FULL OPTIONAL TAPPING CENTER high torque/power version, complete with: spindle cone with BIG PLUS attachment FANUC DDR-T: continuous fourth axis (direct drive motor) with braked counter support and plate Kdsdeuby Sxspfx Afvjl rotary joint for hydraulic feed to center table (for automatic workpiece clamping/unclamping) hydraulic power unit for workpiece clamping high-pressure refrigeration through the spindle chip conveyor evacuation automatic side poet robot interface tool setter RENISHAW TS-27 perfect machine with only 4,500 spindle hours!