Used Heating Press for sale (26,469)

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Lsdpfezuzw Djx Acfjaf Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1996, Continuous press Manufacturer: OTT Type: 300-K-D0 Year of manufacture: 1996 Technical data Plate dimensions: 2550 x 1350 mm Lasdpfozuzwwjx Acfef Hot water heating 6 pressure cylinders Total pressing force: 135 t Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2007, Lamination press Manufacturer: Dimter Type: PROFIPRESS L2500 Year of manufacture: 2007 Technical data Wood dimensions to be processed Wood width, panels: 30 - 150 mm Wood thickness: 11 - 60 mm Wood inlet length: 800 - 2500 mm Panel widths, variable: max. 1300 mm Specific pressing pressure for cross-sections of 2500 x 60 mm: up to 1.6 N/mm2 The pressing surface per press cycle must not be smaller than 100 cm2 Filling width of the press per cycle: min. 650 mm / max. 1300 mm Max. filling area of the press per cycle: 3.25 m2 (The max. usable press width depends on the widths of the individual lamellas.) Wood type Softwood/hardwood Press without options Electrical connection, press: 7 kW Electrical connection, 40 kW generator: 56 kW Operating voltage: approx. 400 Volt / 50 Hz (C/s) Collection table extended to 3700 x 1300 mm, with stainless steel wood support Motor-driven multi-function slider Lamination press Profipress L 2500 Press bed area approx. 2500 x 1300 mm Sturdy base frame with lower press table made of stainless steel as a grounding electrode Quick-change stop guide sets for panel thicknesses of 19 - 40 mm, which can be hydraulically adjusted to the current filling width Hydraulic special pressure elements ensure uniform pressure distribution over the entire joint length and compensate for tolerances In multi-lane operation, filling widths may vary by a maximum of 15 mm Upper pressure plate with hydraulic drive generates high vertical pressing pressure for minimal displacement Integrated hydraulic unit for generating pressing force and driving the hydraulic motors Control cabinet and control panel Protective cladding Additional individual pressure elements from above Automatic gluing station with precision gluing head Infeed for different widths Camera Washing and rinsing device for gluing head Lajdpfxjzuzwqe Acfsf Modem incl. software for online connection Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2019, Corpus press Manufacturer: LINYI JIANZHONG WOOD MACHINERY Type: JJZ-CP Year of manufacture: 2019 The JJZ-CP press is suitable for the production of plywood, doors, and MDF panel joints. The feeding and removal of the glued elements are carried out automatically via powered roller conveyors. Technical data - Max. pressure 500 t (adjustable) - Max. filling height 1300 mm - Min. filling height 900 mm - Max. filling size 1300 x 2500 mm - Press dimensions 3600 x 1370 x 4500 mm - Press placement approx. 500 mm below floor level - Feeding table 2000 x 1960 mm - Receiving table 2350 x 2500 mm - Max. power 13.2 kW - Weight 12000 kg - CE marking - Capacity: 6 batches per hour 2 corpus presses are available for sale. Lasdpfx Aszuzwkjcfjf Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1998, Continuous body press Manufacturer: LIGMATECH TYPE: MPP 15 Year of manufacture: 1998 The MPP 15 is a flexible press for batch-related production without setup times. The MPP 15 can be used individually or in various combinations in an assembly line. The pressing forces are applied pneumatically. The separately adjustable vertical and horizontal pressure allows for pressing both horizontal and vertical bodies. The vertical forces are transmitted through a plate, while the horizontal forces act on the body via press cheeks. The position of the center press cheeks can be adjusted using adjustable stops, allowing for different heights of bottoms and sides. During the infeed process, the body is measured photoelectrically, which automatically positions the horizontal pressure bar. Technical data: Body dimensions: Length: min. 300 mm / max. 2300 mm Height: min. 300 mm / max. 1220 mm Depth: max. 600/800/1000 mm (depending on the press type) Pressing pressure: vertical max. 17 kN horizontal max. 16 kN Working height: 500 mm Transport speed: min. 8 m/min. / max. 37 m/min. Pressing time: selectable up to 999 s Operating voltage: 400 V, 50 Hz Control voltage: 24 V DC (according to VDE) Required air pressure: 5...8 bar Air consumption: 120 NL/cycle Total connected load: 3 kW Weight: approx. 4 tons Required room height: 3000 mm Extended infeed belt as a staging area Lodpfx Aezuzv Tscfsaf Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2000, Corrugated board press Manufacturer: Hüttenhölscher Year of manufacture: 2000 Technical data Ljdjzuzvmopfx Acfjaf Voltage: 400 V Current: 32 A Frequency: 50 Hz Compressed air: 6 bar Note: The technical data and descriptions are a transcript of the order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2001, Short-cycle pressing line Manufacturer: Wemhöner Type: KT-F-1E Year of manufacture: 2001 Technical data - Pressing area: 5,750 mm x 2,200 mm - Operating side: left - Plate dimensions: Length: 2 x 2,600 mm - 2 x 2,620 mm Width: 2,070 mm Lasdpfx Aozuzi Tocfef Thickness: 6 mm - 40 mm - Pressing pressure: approx. 40 kg/cm² Note: Upon request, the complete layout plan of the system can be sent. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 1998, - Lengths: 1,800 - 2,300 mm - Widths: 500 - 1,300 mm - Thicknesses: 35 / 40 / 44 mm Door pressing system Manufacturer: Wild Year of manufacture: 1998 For door dimensions: - Lengths: 1,800 - 2,300 mm - Widths: 500 - 1,300 mm - Thicknesses: 35 / 40 / 44 mm Consisting of the following sections: 1. Continuous door panel gluing with frame assembly station / 2. Pressing line with hardboard facing station Section 1 consists of: - Gantry loading system - Angle transfer with longitudinal and cross saws - Loading and feeding of the longitudinal and transverse frame parts from magazines - Longitudinal cutting station for the longitudinal frame parts - Connecting station of the frame parts with the door panel core. With clamping devices - Conveyor belt angle transfer with shuttle transfer of the door panel cores onto the glued hardboard Section 2 consists of: - Loading of the hardboard - Brush cleaning machine - Hardener application machine from below - Glue application machine from below - Roller conveyor - Angle transfer for the lower hardboard - Vacuum reversing device for the upper hardboard - Automatic facing station for hardboard and door panel cores - 2 door presses, each with 2 x 4 pressing stations, arranged parallel to each other - Both presses are loaded at the infeed with 1 shuttle loading basket - Both presses are unloaded at the outfeed with 1 shuttle unloading basket Ljdezuzgrjpfx Acfjaf - Angle transfer to the infeed into a hedgehog buffer - Angle transfer at the outfeed of the hedgehog buffer and feeding to the stacking station - One-sided vacuum stacking with protective plate space Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Year of construction: 2017, condition: excellent (used), REF: MM6476 1 x 2017 Packaging Automation Ltd Eclipse SL4 inline heat-sealing machine supplied with 1 x Packaging Automatic Ltd Eclipse C1 automated chain-and-peg conveyor system, 2 x interchangeable sets of tooling and some spare parts. Previously used to heat seal punnets of cauliflower and cauliflower/broccoli mix from multi-head weigher. Both machines on height adjustable feet. Ledpfx Aozrg T Escfoaf The Eclipse SL4 is a fully automatic inline tray-sealing machine designed for high-throughput food packaging applications. Suitable for sealing a wide range of pre-formed trays, the machine is ideal for use within the meat, poultry, seafood, ready meal, fresh produce, bakery, and convenience food sectors. The automated conveyor system provides continuous product handling, helping to improve production efficiency and throughput. Specification: Model of inline heat sealer - Eclipse SL4. Serial number - EC34-MC-00100. Model of indexing inline conveyor – Eclipse C1. Date of manufacture - 2017. Tooling - 2 x sets. Set 1: 4 x 1 format with arms. For punnets (double section) measuring 261mm L x 166mm W x 55mm D. Set 2: 4 x 1 format with arms (single punnet - in machine) measuring 177mm L x 140mm W x 55mm D. Eclipse C1 infeed conveyor belt (modular plastic belt section) - 300mm wide. Outfeed conveyor belt - 290mm wide, blue rubber. System footprint: Eclipse C1 indexing conveyor footprint - 3870mm L x 950mm W x 1050mm H. Eclipse SL4 inline sealer footprint - 3230mm L x 1050mm W x 2050mm H. Condition – Very good. This system was purchased new and run for approximately 6 months per year. Supplied with various spare parts, including cutters for both sets of punnets, spare belts, heater pads, etc. *Please note* - None of the following equipment pictured is included in the sale: multi-head chutes with sensors feeding the C1 infeed conveyor AND thermal transfer coder mounted on Eclipse SL4 inline sealer.

Condition: used, Year of construction: 1989, machine/vehicle number: SN: 00789901, functionality: unexamined, pressing force: 815 t, Press 1, manufacturer: Umformtechnik Erfurt GmbH, type: PKZZI 800.1/3150x1600/500E, serial number: 00789901, year of manufacture approx. 1989, 8000 kN, last service in 10/2025, machine in operation until 12/2025. Technical data of the press according to the nameplate: Press force max. 8,000 kN – at a distance in front of the die of 12.5 mm Press force 2,500 kN – at a distance in front of the die of 200 mm Stroke rate in idle 10 to 20 min-1 Stroke of the ram 500 mm Adjustability of the ram: 500 mm Lajdpfozvdm Rex Acfjf Strip feed system consisting of: Roller feed, manufacturer: GSW Schwabe, type VRMA80/78, machine no. 2011-60187, year of manufacture 2011 with reel 1 (sandwich processing), SAWAB reel, year of manufacture 2011 with reel 2, manufacturer: GSW Schwabe, type: LMHR1000/1100, no.: M2011-00171, year of manufacture 2011 with reel 3, manufacturer: GSW Schwabe, type: MHR5/1400, serial no.: M2011-00170, year of manufacture 2011 including enclosure GWS project no.: 2011-60187 with peripherals: - Conveyor belt - Raziol system Function and technical data not verified without additional items/without further accessories, unless explicitly stated as part of the item WE STRONGLY RECOMMEND PARTICIPATING IN THE INSPECTION! If interested, please contact us via email!

Condition: excellent (used), Year of construction: 2012, functionality: fully functional, pressing force: 100 t, stroke length: 200 mm, Equipment: CE marking, safety light barrier, For Sale: Bystronic Xact 100 CNC Press Brake (3.1m x 100T) Available immediately: A exceptionally clean, well-maintained Bystronic Xact 100 CNC Press Brake (2012 Model). This free-standing, down-stroking machine offers precision 4-axis bending with automated crowning, making it an excellent addition to any precision fabrication facility. Detailed technical specifications and machine configurations can be verified through the Bystronic Official Group Website. Machine Overview & Configuration Control system: Equipped with a Cybelec DNC 880S Control unit. Axis configuration: 4-Axis control plus crowning (Y1, Y2, X, R + Manual Z). Safety systems: Integrated Fiessler Laser Guards for optimal operator protection. Guarding package: Features full rear sliding screen guards and side guards. Wandering foot pedal/pedestal controls. Technical Specifications Laodpozta A Aefx Acfsf Parameter Measurement Bending Capacity1000 kN (100 Tonne) Working Length3100 mm Distance Between Frames2550 mm Throat Depth400 mm Maximum Stroke200 mm Rapid Approach Speed100 mm/s Working Speed1 – 10 mm/s Return Speed95 mm/s Overall Weight9000 kg Machine Identity Manufacturer: Bystronic Model: Xact 100Year of Manufacture: 2012 (Model Year 2012)

Condition: used, Year of construction: 1998, machine/vehicle number: SN: 5-2067, functionality: unexamined, power: 45 kW (61.18 HP), pressing force: 255 t, overall weight: 24,800 kg, PME Erfurt, Type: ZH 2500 / 1600, Serial No.: 5-2067, Year: 1998, 2500 kN, in operation until December 2025 Technical data of the press according to the nameplate: Press force: 2,500 kN Stroke rate: 25-75 strokes/min Rated stroke rate: 40 strokes/min Stroke: 20-200 mm Ram adjustment: 140 mm Total power: 45 kW Operating voltage: 400 V Frequency: 50 Hz Machine weight: 24,800 kg Strip feeding system consisting of: PBK, Type: Roller feeder WV-120/DSM 500P, Serial No.: BA00482, Year: 1998, PBK, Type: Straightening machine, Year: unknown, PBK, Type: Unwinding reel SCi 530 M, Serial No.: BA00482, Year: 1998 including enclosure and roller conveyor with peripherals: - Conveyor system Ljdpfx Aszvcxlecfsaf Functionality and technical data have not been verified. without additional items/without further accessories, unless explicitly stated as part of the item. If interested, please contact us by email.

Condition: used, Year of construction: 2019, machine/vehicle number: M01645/400/23/051/19, functionality: unexamined, power: 75 kW (101.97 HP), Schuler, Type: Eccentric press MC400, Machine No. M01645/400/23/051/19, Year of manufacture 2019, 4000 kN Technical data of the press according to the nameplate: Supply voltage: 3LNPE/400V/50Hz Control system: CCS/PNOZmulti Fuse rating: 250 A Rated power: 75 kW Rated force: 4,000 kN Work capacity: 60,000 J Max. strokes in continuous operation: 20-80 strokes/min Max. strokes in single-stroke operation: 30 strokes/min Max. clutch cycles in single-stroke operation per minute: 20 Post-travel time: 0.20 sec Min. safety distance: 322 mm Min./max. clutch pressure: 5.5/6.0 bar Lodszvcgpjpfx Acfsaf System pressure: 6.0 bar Stroke lengths: 40-315 mm Maximum ram adjustment: 200 mm Standard connection point of the ram: OU Max. installation space, largest stroke in UU: 750 mm Table dimensions: 3000 x 1400 mm Max. tool dimensions: 3000 x 1300 mm Max. weight of tool upper part: 2,800 kg Weight without additional equipment: 72,000 kg Strip feeding system consisting of: GSW Schwabe, Type: MHR 5/2000, Serial No. M 2018-01118, Year of manufacture 2019 GSW Schwabe, Type: RMA 50/79, Serial No. M 2018-01119, Year of manufacture 2019 Including hydraulic unit, enclosure, and roller conveyor GSW project no.: 2018-60420 with peripherals: - SCHÄFER lubricant supply system with tank - RAZIOL EST-10-D ELS-400, Year of manufacture 2018 - Conveyor belt - GÜTHLE ACT10F2000/2400N, Set of 2, Year of manufacture 2019 - Control cabinet Function and technical data have not been verified. Without further items/without further accessories, unless explicitly specified as part of the item. If interested, please contact us by email.

Condition: excellent (used), Year of construction: 2004, operating hours: 76 h, machine/vehicle number: HF112305, Size 47 x 66 cm, Console DTC (Sakurai Delivery Top Console) with Touch Screen, Full Remote Control Operation, SIS (Sakurai InterActive System) for make-ready, Plate Running Register system, SAS (Sakurai Auto Set) for paper size and thickness, SPC (Semi-automatic Plate Change), Cocking Register, Automatic Washers: Blanket Cylinders & Inking Rollers, Olivermatic Dampening, Baldwin Refrigeration System & Bal Control, Feeder with Suction-belt feed table, Electronic Double Sheet & Side Lay Detector, Chromed Impression Cylinders, Perfector 4/0 - 2/2 (Fully automatic), Semi-High Pile delivery, Powder Spray. Lajdpfxszubgrs Acfjf

Condition: good (used), Year of construction: 2016, machine/vehicle number: TAD174116002, Offer 26235 Technical data: - Working width: 4100 mm - Pressing force: 170 t - Distance between columns: 3600 mm - Overhang: 400 mm - Max. installation height: approx. 400 mm - Ram stroke: 225 mm - Working height: approx. 920 mm - Motor power: approx. 18 kW - Oil capacity: approx. 300 l - Space requirement: approx. W 4800 x H 2750 x D 2300 mm - Weight: approx. 12500 kg Laodszu Na Hjpfx Acfef - Includes: - Swivel arm – control panel with ESA control - For 4 axes Y1 + Y2, X, Z - Motorized back gauge with motorized height adjustment - Crowning - Safety – light curtain - 4-way universal die + split ram tool 4000 mm - Pointed tool 4000 mm - Ram tool 3000 mm - V-die 3000 mm - Electric foot switch - Side-mounted adjustable support arms

Condition: excellent (used), Shelf length: 225 cm Shelf width: 135 cm Maximum heating element height: 40 cm Maximum temperature: 120 °C Ljdpfezvnq Hox Acfeaf Total power consumption: 14 kW

Condition: refurbished (used), 105m3 horizontal steel tank with heating coil Ledpfx Aexqfwtocfsaf Diameter: 2.80m Length: 17.10m

Condition: used, 30m³ stainless steel tank features a full-height stainless steel coil Diameter 2.97m Total height 5.40m Cylinder height 4.30cm Leg height 30cm Ledpeyw Ub Refx Acfsaf Cone height 30cm Gear motor height 50cm

Condition: good (used), Year of construction: 1963, Stroke = 250 mm On request, transport and loading can be organized across Europe at an additional cost. Prices excl. VAT Ledpfx Acszvnd Tofjaf Inspection possible by appointment. Contact us – our team will be happy to assist you. Machinery Purchase / Sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES, MACHINE TOOLS, ETC. Do you need a high-quality yet affordable machine for your production? Or do you want to sell your equipment? For further information or contact options, please use the contact form.

Condition: good (used), Year of construction: 2012, Condition: 2012 overhauled to the latest UVV Installation height: 800 mm Ram stroke: 500 mm Projection: 360 mm Nominal force: 400 kN Hydraulic pressure: 160 bar Operating hours: 1356 Other: new control from Pilz, electrical circuit diagrams available Ljdpfx Acszvnfdjfoaf Video about functionality available

Condition: good (used), operating hours: 4,313 h, power: 22 kW (29.91 HP), input voltage: 400 V, input frequency: 50 Hz, pressing force: 320 t, stroke length: 250 mm, operating speed: 7 mm/s, reverse speed: 70 mm/s, table width: 250 mm, table length: 6,100 mm, throat depth: 300 mm, distance table to ram: 500 mm, clearance between the columns: 5,500 mm, oil tank capacity: 350 l, overall weight: 26,000 kg, Max. pressing force: 320 t Bending length: 6100 mm Distance between uprights: 5500 mm Control system: MNC 95 c Maximum ram stroke: 250 mm Max. distance table/ram: 500 mm Overhang: 300 mm Table width: 250 mm Closing speed: 80 mm/s Working speed: 7 mm/s Return speed: 70 mm/s Oil capacity: 350 l Operating hours: 4312 h Voltage: 380 V / 50 Hz Lasdpjzvb Rmsfx Acfef Total power consumption: 22 kW Machine weight approx.: 26 t

Condition: good (used), Year of construction: 1987, pressing force: 1,250 t, Press force 1250 t Bending length 15000 mm Upright spacing 10160 mm Control system CNC 10 graphics Throat depth 770 mm Table length 15000 mm Machine weight approx. 230 t Required space approx. 17000 x 5400 x 5900 mm Additional information: - Press force: 1,250 t - Bending length: 15,000 mm - Control: CNC 10 graphics - Number of controlled axes: at least 10 - Upright spacing: 10,160 mm Laodjzvb I Sepfx Acfsf - Throat depth: 770 mm - Table length: 15,000 mm - Dimensions: 17,000 mm x 5,400 mm x 5,900 mm - Weight: approx. 170 t Equipment: - Crowning device - CNC 10 graphic control - Hydraulic upper tool clamping - Multi-operator functionality - Increased speeds - Automatic, height-adjustable rear sheet gauge - Draw cushion device - Horn length on each side: 2,200 mm

Condition: good (used), Year of construction: 1990, pressing force: 3,000 t, Bending length: 14,000 mm Column width: 10,500 mm Control: CYBELECCNC 7000 with graphic Table width: 1,000 mm Distance between table and press beam: 1,800 mm Controlled axes: Y1; Y2; X1; X2 Control system was renewed in 2012 Total power requirement: 75 kW Machine weight approx. min.: 465 t Lodpjzva Ahsfx Acfoaf Space requirement approx.: 14,600 x 4,200 x 7,200 mm Additional information - Distance between table and press beam: 1,800 mm

Condition: good (used), Year of construction: 1994, Pressure: 250 t Throat depth: 360 mm Table size: 1250 x 630 mm Table diameter: 250 mm Ram clamping surface: 850 x 450 mm Installation height: 800 mm Piston stroke: up to 500 mm Piston diameter: 400/360 mm Lodpfx Ajzvaymscfsaf Ram speed downward: 200 mm/sec Ram speed upward: 110 mm/sec Total power requirement: 20.5 kW Machine weight approx.: 8 t

Condition: good (used), Year of construction: 1975, Pressure: 250 t Throat: 400 mm Stroke: 30...140 mm Table size: 1000 x 750 mm Passage opening in table: 360 x 400 mm Ram area: 630 x 500 mm Laodpfx Acszvayasfjf Ram adjustment: 110 mm Total power requirement: 18 kW Machine weight approx.: 16 t