Used Kellenberger Kel-Vita Mit Lader for sale (8,955)

Condition: new, maximum load weight: 45,250 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete inventory of vehicles available for immediate and short-term delivery on our website. Excerpt from the equipment list. Full specifications available upon request. Chassis, stepped: * Special steel frame made from high-strength fine-grained steels, electrically welded at connection points * Generously dimensioned outer frame. 4-axle configuration * Wheel covers over the axles with spray suppression * All steel parts sandblasted Ledewx Dbispfx Akyork * Side underrun protection made of anodized aluminum mounted * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the stepped area for the longest possible low-bed length in combination with AluLeg drop supports instead of telescopic support legs, maximum rear swing clearance of the tractor unit approx. 2,100 mm Special body with rear stake extension: * DINKEL – special body * Self-supporting aluminum roof beam / profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stakes extendable for loading/unloading up to approx. 4,200 mm * Three sliding stakes per side with elastic relief * Additional intermediate stake lockings in roof beam and parked position, via pull cable and spring bolt * DINKEL – mechanical lift roof, height-adjustable * Lift roof height approx. 400 mm, operable from both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments by adjusting the stakes * Front cover at bulkhead for driving operation under the tarpaulin up to a total height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminum slats on the side, 450 pockets below, four rows of single pockets above. Only three rows of slats in the raised platform, spacings evenly distributed Floor: * Approx. 27 mm special waterproof bonded beech phenolic plywood, rough surface * Steel sheet in the wheel well area. Suitable for forklift traffic as per DIN standard * Outer frame flush with deck surface Brakes: * WABCO air brake system with EBS according to EC Directive 71/320, including PREV (Parking-Release Safety Valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with mileage counter and axle load display * Including WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF with drum brakes in low-loader design * Air suspension with lift and lower device, total lift approx. 230 mm * Third and fourth axles as friction-steered trailing axles with electric and mechanical lock Twin tires: * 235/75 R 17.5, 16-ply. Make of our choice, including spare wheel holder * Without spare wheel Lighting: * According to EU regulations, including LED side marker lights * Position lamps in LED design * 2 additional reversing lights * 2 work lights on the inside front wall, upper section Paintwork: * Chassis and body in one color, RAL 3002 carmine red * Intermediate stakes, axles KTL-coated black * Corner stakes hot-dip galvanized * Plastic parts black * Galvanized parts unpainted * Rims in factory silver Special equipment included: * 15-pin electrical supply cable * Air suspension in ECAS design, operated on the trailer * Oversize signage front and rear in galvanized, infinitely telescopic design with installed marker lights, including sockets for rotating beacons (small signs) * Additional external release for sliding roof frame lock * 4 stake adapters for special outer frame profile, to lock intermediate stakes as needed * PVC sliding tarpaulin, color similar to RAL 9

Condition: new, maximum load weight: 8,770 kg, Year of construction: 2025, ABS Müller Mitteltal ETÜ TA R 11.9 Tandem Low Loader with many extras Equipment includes: - 2 spring-assisted lifting devices for 400 mm high steel side walls - Reinforced and certified construction according to EN 12642 XL load securing certificate - 10 UVV lashing rings integrated into the existing external frame hole pattern - Additional wooden floor in clamped design - Tyres: 235/75R17.5 - Four BPW axles instead of GIGANT - Platform extension by 870 mm, total length 6,270 mm - One-piece ramps with hot-dip galvanized anti-slip grating - Lockable toolbox with 45 kg payload capacity Paintwork: - Wheels: silver - Chassis/front wall/drawbar/rear wall/stanchions/ramps: hot-dip galvanized - Axles/springs: black Lodpfx Akexcxmfsysrk - Side walls: RAL2011 deep orange We are happy to offer you suitable financing, hire purchase or leasing options. Delivery or shipping by arrangement. We always have a selection of new machines in stock, as well as demonstration units. Contact us today! We rent vehicles and machines with or without operator. A wide range of used machines and equipment always available. Technical changes, errors and prior sale excepted.

Condition: used, empty load weight: 5,100 kg, maximum load weight: 12,900 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 12/1998, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 1 mm, total length: 2,550 mm, total width: 1,600 mm, suspension: steel, tire size: 235/75R17.5, wheelbase: 5,400 mm, color: orange, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 2-axle, SAF axles, turntable, leaf suspension, ABS (anti-lock braking system), lashing eyes, container lock, U-protection, pneumatic adjustable drawbar, aluminum side wheel guards, twin tyres, storage box, removable drop sides Lredpfxsi Rpxwj Akysk Wheelbase: 5400 mm Body: Trailer for roll-off containers in lengths 6m-6.75m SAF axles type SKRZ 11030, pneumatic low-tension hook device, 2x pockets for plug-in locking hooks, 4x pockets for plug-in container centering and skip stop. The trailer can also be used as a flatbed! Aluminum side walls 600 mm high are included with the trailer! Drive-on ramps available for an extra charge of 900.00€ net! ACCESSORY INFORMATION WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! - .

Condition: used, first registration: 11/2006, Year of construction: 2006, MÜLLER - MITTELTAL T4 Kompakt Turntable - Low-loader with air suspension and wheel recesses - 4 x air-suspended GIGANT axles - air suspension - 4 x wheel recesses - mechanical loading ramps - 2 foldable rear supports - extendable warning panels - ABS - MICHELIN tyres: 235/75 R 17.5 - heavy-duty version: 40,000 kg GVW - unladen weight: 8,400 kg - overall length: 11,750 mm - 50 mm towing eye Particularly suitable for transporting lime milling machines! Ljdpfx Akewmpbdsyork - German trailer - General inspection / safety test available on request and at extra cost! Subject to prior sale and errors!

Condition: used, empty load weight: 8,580 kg, axle configuration: > 3 axles, first registration: 05/2015, loading space length: 13,620 mm, loading space width: 2,480 mm, loading space height: 2,750 mm, loading space volume: 93 m³, tire size: 385/65 R22,5, Year of construction: 2015, mileage: 673,981 km, Equipment: ABS, Leergewicht: 8580kg, Laderaum (L B H): 13.620 mm x 2.480 mm x 2.750 mmReifengröße: 385/65 R22.5, Laderaum Volumen: 93 m³, 1. Achse: , 2. Achse: , 3. Achse: , 4. Achse: , Unterfahrschutz statisch, Nachlauflenkung, Mitnahmehalterung Gabelstapler, Anschlußstecker 1x15 und 2x7 polig, Unser gesamtes Fahrzeugangebot finden Sie unter . Finanzierung gewünscht? Mit unseren Value Added Service bieten wir Ihnen individuelle Finanzierungsmöglichkeiten, Full Service-und Telematik-Dienstleistungen. Wir beraten Sie gerne. Lrodpfx Aey E Updjkyjk

Condition: used, axle configuration: 2 axles, first registration: 06/2019, loading space length: 13,550 mm, loading space width: 2,460 mm, loading space height: 2,750 mm, total length: 13,800 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 265/70R19.5, wheelbase: 9,810 mm, color: white, Year of construction: 2019, Equipment: ABS, tail-lift, 1st axle liftable. 2nd axle forcibly steered. Tail lift: Zepro, 2,500 kg, 200 cm. = Further information = Axle configuration Tyre size: 265/70R19.5 Brakes: Drum brakes Suspension: Air suspension Lsdpfxowg Alie Akysrk Rear axle 1: Twin tyres; Tyre tread left inner: 50%; left outer: 50%; right inner: 50%; right outer: 50% Rear axle 2: Twin tyres; Steered; Tyre tread left inner: 30%; left outer: 30%; right inner: 30%; right outer: 30% Weights Unladen weight: 8,680 kg Payload: 26,320 kg Gross vehicle weight: 35,000 kg Functional Tailgate: Zepro Identification Type number: TAIL LIFT / STEERING AXLE / LIFT AXLE / = Company information = ALL PRICES ARE NET EXPORT PRICES. Joris Versteijnen (NL-DE-GB), Wouter Greutink (NL-DE-GB-ES-IT). We speak Russian. We make every effort to provide correct information but no rights can be derived from the listed texts.

Condition: used, axle configuration: 2 axles, first registration: 08/2019, loading space length: 13,500 mm, loading space width: 2,460 mm, loading space height: 2,750 mm, total length: 13,820 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 265/70R19.5, wheelbase: 7,990 mm, color: white, Year of construction: 2019, Equipment: ABS, tail-lift, = Additional Options and Accessories = - Air suspension - Toolbox = Notes = COC document. First axle: lift axle. Second axle: steering axle. Tridec steering system. BPW axle with drum brakes. Internal dimensions: 1350 cm x 246 cm x 275 cm. Zepro tail lift: Type: ZDK 250-155 MA. 2,500 kg lifting capacity. = Further Information = Axle configuration Tyre size: 265/70R19.5 Brakes: Drum brakes Suspension: Air suspension Rear axle 1: Twin tires; Tire tread left inside: 20%; Tire tread left outside: 20%; Tire tread right inside: 20%; Tire tread right outside: 20% Rear axle 2: Twin tires; Steered; Tire tread left inside: 40%; Tire tread left outside: 40%; Tire tread right inside: 40%; Tire tread right outside: 40% Weights Lredpfswcqm Hsx Akyek Unladen weight: 8,680 kg Payload: 26,320 kg Gross vehicle weight: 35,000 kg Functional Tail lift: Zepro Identification Type number: STEERING AXLE / LIFT AXLE / TAIL = Company Information = ALL PRICES ARE NET FOR EXPORT. (Joris Versteijnen NL-DE-EN; Wouter Greutink NL-DE-EN-ES-IT) Govorim po russki. We strive to provide correct information, but no rights can be derived from the information provided.

Condition: new, Cantilever rack, new H: 400cm, base +3 storage levels with roof & rear panel Free delivery within Germany, except islands Data : - H : approx. 400 cm - D : approx. 147 cm - L : approx. 1420 cm - Cantilever arms : approx. 125 cm - Axial dimension: 290 cm (can be adapted to customer requirements) - New goods - made in Germany. - Delivery time approx. 6 weeks after commercial clarification. - 1000 kg load per arm - 4000 kg load per upright - Uprights in hot-dip galvanized. - Cantilever arms in hot-dip galvanized. - Arms are bolted. - Arms adjustable in 200 mm increments. - Levels: Base + 3 storage levels (4 storage levels) Shelf consists of : - 06 x uprights, incl. base approx. 400 cm made of IPE270. - 18 x cantilever arms approx. 125 cm made of IPE 120. - 06 x roof girder approx. 150 cm made of IPE 120, 5° rising roof pitch. - incl. roof and rear wall material. - incl. all necessary connecting elements and screws. Why BLT cantilever racks ? - Certified German manufacturer DIN EN 1090 - Made in Germany - All specified load-bearing capacities of the uprights and cantilever arms are statically verifiable at 100% load. - All shelving systems are supplied in a hot-dip galvanized version. They can therefore be installed both indoors and outdoors and do not rust like painted systems. Consistent appearance for many years. - We use the legally prescribed hot-dip galvanized screw fittings in accordance with DIN EN 15048-1 - Long after-sales guarantee - The upright base and upright back are welded together, providing additional safety and short assembly times because the feet do not have to be bolted to the upright back. - Bracing made of angle steel, so no adjustment with turnbuckles necessary. This shortens the assembly time. - No slotted hole system, therefore no weakening of the upright profile. Price : 12.250,00 € net plus statutory value added tax. You will receive an invoice with VAT shown. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your operating equipment. Our recommendation : Let us know what you need... Ledpfx Akjy D Sxaoyjrk We will be happy to help you with the realization of your projects, from planning and ordering to installation.

Condition: new, Year of construction: 2024, functionality: fully functional, carrying capacity per cantilever arm: 140 kg, shelf height: 2,500 mm, total length: 3,150 mm, total height: 2,500 mm, axle spacing: 1,030 mm, load capacity per stand: 1,120 kg, approx. 3.15 running meters Cantilever rack with shelves 60 cm deep H: 250 cm 140 kg/arm META Multistrong Data : - H : approx. 250 cm - D : approx. 81 cm - L : approx. 315 cm - Cantilever arms : approx. 60 cm - Axial dimension : 103 cm - NEW GOODS immediately from stock. - 140 kg load per arm - 1120 kg load per upright - Uprights in RAL5010 (gentian blue). - Cantilever arms in RAL5010 (gentian blue). - Arms are hooked in and secured with locking bolts. - Arms adjustable in 70 mm increments. - Levels: Base + 4 storage levels (5 storage levels) Shelf consists of : - 04 x uprights, incl. base approx. 250 cm made of IPE120. - 16 x cantilever arms approx. 60 cm made of rectangular profile 40 x 30 mm. - 12 x META shelf, approx. 100 x 60 cm - incl. all necessary connecting elements and screws. -- Available immediately Price : 1765,00 € net 2100,35 € gross You will receive an invoice with VAT included. Ledpfx Aksy D Stkjyork Accessories such as ground anchors, collision protection etc. can also be purchased from us. Transportation : The delivery is carried out on request by our partner forwarding agency, the costs depend on the postal code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.

Condition: new, empty load weight: 3,280 kg, maximum load weight: 9,720 kg, overall weight: 13,000 kg, axle configuration: 2 axles, loading space length: 5,110 mm, loading space width: 2,430 mm, loading space height: 900 mm, loading space volume: 11 m³, suspension: steel, color: other, gearing type: other, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Three-way tipper, with side wall extension 900 mm high, loading height approx. 940 mm, front wall - foldable for overloading, central locking for side and rear drop sides, automatic rear wall opening when tipping backwards, side drop sides swinging and foldable, side drop sides with spring relief, bridge floor made of fine-grained steel 4 mm, 8 x strong lashing eyes recessed in the floor, 5-stage hard chrome-plated three-sided tipping cylinder, tipping angle: 50 degree tipping angle to the rear and 45 degree tipping angle to the side, infinitely height-adjustable drawbar, stanchions pluggable at the rear, geared support winch with load and fast gear, front, mounting shaft for two aluminum ramps integrated in the chassis, lockable ramp shaft (privacy screen), contour marking according to ECE R 048 regulation, , Rental price from 550 ¤, , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Lrjdpfsy Etgbox Akyok

Condition: new, empty load weight: 3,280 kg, maximum load weight: 9,720 kg, overall weight: 13,000 kg, axle configuration: 2 axles, loading space length: 5,110 mm, loading space width: 2,430 mm, loading space height: 900 mm, loading space volume: 11 m³, suspension: steel, color: other, gearing type: other, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Three-way tipper, with side wall extension 900 mm high, loading height approx. 940 mm, front wall - foldable for overloading, central locking for side and rear drop sides, automatic rear wall opening when tipping backwards, side drop sides swinging and foldable, side drop sides with spring relief, bridge floor made of fine-grained steel 4 mm, 8 x strong lashing eyes recessed in the floor, 5-stage hard chrome-plated three-sided tipping cylinder, tipping angle: 50 degree tipping angle to the rear and 45 degree tipping angle to the side, infinitely height-adjustable drawbar, stanchions pluggable at the rear, geared support winch with load and fast gear, front, mounting shaft for two aluminum ramps integrated in the chassis, lockable ramp shaft (privacy screen), contour marking according to ECE R 048 regulation, , Rental price from 550 ¤, , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Ljdpfey Eic Sex Akyerk

Condition: new, empty load weight: 3,280 kg, maximum load weight: 9,720 kg, overall weight: 13,000 kg, axle configuration: 2 axles, loading space length: 5,110 mm, loading space width: 2,430 mm, loading space height: 900 mm, loading space volume: 11 m³, suspension: steel, color: other, gearing type: other, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Three-way tipper, with side wall extension 900 mm high, loading height approx. 940 mm, front wall - foldable for overloading, central locking for side and rear drop sides, automatic rear wall opening when tipping backwards, side drop sides swinging and foldable, side drop sides with spring relief, bridge floor made of fine-grained steel 4 mm, 8 x strong lashing eyes recessed in the floor, 5-stage hard chrome-plated three-sided tipping cylinder, tipping angle: 50 degree tipping angle to the rear and 45 degree tipping angle to the side, infinitely height-adjustable drawbar, stanchions pluggable at the rear, geared support winch with load and fast gear, front, mounting shaft for two aluminum ramps integrated in the chassis, lockable ramp shaft (privacy screen), contour marking according to ECE R 048 regulation, , Rental price from 550 ¤, , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Lrjdpfsy Eh Sfex Akyjk

Year of construction: 2026, condition: new, Our KVK 1A is the almost identical sister model to the KVK 2 (MA), i.e. a semi-automatic stretch wrapper with turntable which, in comparison to the KVK 2 MA, is equipped with a cut-out for ground-level access with a hand pallet truck. Ljdpfx Akey Drhzjyork The only thing that still has to be done manually with this wrapper is feeding and cutting the film. With a weight of 700 kg, this model is also designed for professional use and can be loaded up to 1500 kg. The 1A has a turntable of 1500 mm and can wrap pallets up to 2400 mm high as standard. With adjustable speeds of the turntable and film carriage, as well as an electromagnetic brake that can be very finely adjusted via potentiometer, you can adapt the automated wrapping process perfectly to your product. Automatic recognition of your pallets (via photocell) is just as much a matter of course as adjustable head and foot wrapping. Programs are available for "up only" wrapping, "up & down" (cross wrapping) and "rainproof" wrapping. If required, the winder can also be controlled manually. If the winder needs to be used at a different location in between, it can be easily lifted and moved with a forklift using the integrated cut-outs. In addition to a photocell for detecting dark packages or black film, the wrapping height of the KVK 1A can be varied as an option (up to 3200 mm). Recommendation The KVK 1A is ideal if no ramp can be used for space reasons or if particularly heavy or unstable packaged goods are not to be pushed onto the turntable via a ramp. For further information, we have attached the technical data sheet as a PDF to this advertisement!

Year of construction: 2026, condition: new, Our KVK 1A is the almost identical sister model to the KVK 2 (MA), i.e. a semi-automatic stretch wrapper with turntable which, in comparison to the KVK 2 MA, is equipped with a cut-out for ground-level access with a hand pallet truck. The only thing that still has to be done manually with this wrapper is feeding and cutting the film. With a weight of 700 kg, this model is also designed for professional use and can be loaded up to 1500 kg. The 1A has a turntable of 1500 mm and can wrap pallets up to 2400 mm high as standard. With adjustable speeds of the turntable and film carriage, as well as an electromagnetic brake that can be very finely adjusted via potentiometer, you can adapt the automated wrapping process perfectly to your product. Automatic recognition of your pallets (via photocell) is just as much a matter of course as adjustable head and foot wrapping. Programs are available for "up only" wrapping, "up & down" (cross wrapping) and "rainproof" wrapping. If required, the winder can also be controlled manually. If the winder needs to be used at a different location in between, it can be easily lifted and moved with a forklift using the integrated cut-outs. In addition to a photocell for detecting dark packages or black film, the wrapping height of the KVK 1A can be varied as an option (up to 3200 mm). Lodpfx Aey Drfyekysrk Recommendation The KVK 1A is ideal if no ramp can be used for space reasons or if particularly heavy or unstable packaged goods are not to be pushed onto the turntable via a ramp. For further information, we have attached the technical data sheet as a PDF to this advertisement!

Year of construction: 2026, operating hours: 1 h, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S23NEOS06, Exhibition facility Stretch winder ATLANTA NEOS ARYA system for automatic foil blowing and cutting. Ledpfx Asyktv Sjkyjrk 99 programs can be saved individually With 1 remote control - optionally more possible Winding height 2150mm Mast height 2050 mm (fits through almost every door) Foil power stretch 120-400% Motorized pre-stretching system with stepless adjustment Adjustable pre-stretching ratio from 120 to 400% via control panel Foil application tension electronically controlled via control unit Fast loading system IEF for easy changing of foil rolls Foil specification Max. outer diameter Ø300mm - height = 500mm - core Ø76mm Automatic foil cutting unit Tension of the film can be saved in 4 steps TECHNICAL DETAILS: two maintenance-free AGM batteries 12 V - 100 Ah connected in series At least 160 pallets per load - loading time: 8 -10 hours High frequency battery charger with LED indicator Wrapping height “machine with MAST (pallet included) 2,150 mm Height query via light button or by entering dimensions on the display Protective bar for emergency stop of the travel drive Emergency stop switch according to CE regulations Acoustic warning signal and warning light when the machine starts Fall protection for the film slide Push button for start & stop Function of the machine according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL: All function parameters can be set via the display - Screen lock program change - Adjustable machine speed around the pallet up to 80 m/min Lifting carriage speed can be adjusted up and down independently of each other - Lifting carriage speed from 1.3 up to 5.4 m/min - Lifting carriage speed down from 1.3 to 5.4 m/min - Number of wraps on the pallet foot (1 - 10 wraps) - Number of wraps on the pallet head (1 - 10 wraps) - Adjustment of pallet wrapping height - Foil application tension foot & head winding / ascent & descent independently adjustable - Foil pre-stretching foot & head wrapping / ascent & descent independently adjustable - Ergonomic height for foil change ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL: 99 storable winding programs for SFERA EASY - Cross winding (up/down) - Simple winding (only up or only down) - Wrap cycle with preset start and stop height - Winding to a stored height (switching off the light button for the height) - Wrapping cycle for large pallets - Winding cycle for cover sheet film - Soft start cycle for application of edge protection - Wrap cycle with gain and adjustable number of wraps Soft start to reduce film tears on sharp pallet edges Winding cycle with manual or motorized line formation (optional) Other systems available immediately from the Ludwigsburg warehouse

Year of construction: 2021, operating hours: 10 h, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S21MythoEasyLow04, Exhibition machine - like new. MYTHO EASY Low Very low height machine Winding height 2400 mm Turntable 1650 mm LP Flat turntable 30mm flat - 500mm long Max. Load weight: 1200 KG PowerStretch 200%, changeable by gear wheels 150-200-250% Automatic adjustable double cord formation - see pictures. Automatic. Cutting Optionbal: Film clamp on turntable German. Schuko plug 6 programs individually storable Further demonstration units available immediately from stock. Prices ex stock Ludwigsburg Lsdpex Ta Nxefx Akysrk

Year of construction: 2025, operating hours: 1 h, condition: as good as new (ex-display), Mytho S with TP / Transparent, accessible at ground level with lift trucks and El. lifts. MAST VERSION Winding height 2450 mm 99 program TOUCH display 7" FILM SLIDE TYPE "PRS" (POWER ROLLER STRETCH) 200% pre-stretching Optionally, more or less pre-stretching possible Ljdpfxsyktrte Akysrk TURNTABLE / TP Ø1650 mm / Opening 06.00 - Mast 12.00 (can be changed at any time) ARYA system for automatic foil blowing and cutting, incl. infrared remote control

Year of construction: 2026, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S25Synthesi01, Stretch Winder Synthesi TECHNICAL DETAILS Turntable / base frame / Ø 2,200 mm Max. pallet dimensions: 1,550 x 1,550 mm Max. load capacity: 2,000 kg Wrapping height (pallet included) 2,200 mm FILM SLIDE TYPE "OPRS - ONE PRE STRETCH" Film pre-stretch ratio set to 200% Foil application tension electronically adjustable in the programs in different steps Height of turntable 75 mm Height query by light button Frequency-controlled turntable drive (soft start - start/stop) Frequency controlled carriage speed up/down Signal tone at the start of wrapping and stop at the end of the cycle Emergency stop switch according to CE regulations The turntable always stops in the same starting position Fall protection for the film slide Push button for switching on the machine and start & stop function & reset according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL All function parameters can be set via the display F00 - Screen lock program change F02 - Infinitely variable turntable speed 5-12 rpm Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Winding height photocell delay F13 - F16 - Foil application tension foot & head wrapping / ascent & descent independently adjustable F62 - Ergonomic height for film change Foil consumption display (optional) ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL 6 storable winding programs F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F01 - 3 - Push button for manual functions F10 - F11 - Wrap cycle with preset start and stop height F12 - Winding to a stored height (switching off the light button for the height) F22 / F23 - Winding cycle for cover sheet film F29 - Soft start cycle for edge protection application F30 - F31 - Wrap cycle with gain and adjustable number of wraps Soft start to reduce film tears on sharp pallet edges Winding cycle with manual or motorized line formation (optional) Reinforcement cycle via push button Optionally possible: Turntable size up to Ø2600 mm Mast height up to 3900mm Lsdpsykub Ajfx Akyjrk ramp mounting frame Light scanner for black products cutting device Etc. Other systems available from the Ludwigsburg warehouse. Some images may contain options that are subject to a surcharge. Illustration similar

Condition: like new (used), first registration: 12/2023, Year of construction: 2023, operating hours: 160 h, Hydraulic oil cooler High-performance hose protection LED light on boom Quick coupler MS01 Standard equipment of the machine, width: 710 mm / 1,100 mm extended 180 mm rubber tracks Double-acting auxiliary hydraulics Two travel speeds CE certification Lrjdpfxsx Tn Upo Akysk This offer is non-binding; no guarantee for equipment details. Subject to errors, changes, and prior sale!

Condition: new, maximum load weight: 40,320 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our full inventory of vehicles, including those available immediately or at short notice, on our website. Partial equipment overview. Full equipment details available on request. Gooseneck: * Gooseneck with rear chamfer of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick. Load area with 5 pairs of folding lashing rings to the outside (LC 5,000 daN) * 3 pairs of folding lashing rings to the outside (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, with checker plate over axles Landing gear: JOST landing gear (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Tyres: * Tyres 205/65 R17.5 - brand of our choice TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Axles: * BPW axles, two rigid axles, two self-steering axles * Air suspension with lift/lower function * Drum brakes * Self-steering axles with electro-magnetic reverse lock, activated via reverse gear or manually Braking system: * WABCO braking system according to EU regulations with EBS-E (4S3M) Electrical system: * Electrical system according to EU regulations, 24 volt ASPÖCK-NORDIK LED lighting (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX at the front connection bar with sockets 24N, 24S & 15-pin in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: * Steel structure made from high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: * HRM-metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure optimum corrosion protection * Trailer color RAL 3002 Carmine Red * Rims Silver Grey * Tarpaulin RAL 9006 (brilliant direct) Options included: * At the gooseneck and at the rear, left and right, a holder for warning signs each, including socket * 2" kingpin * One galvanized steel front wall * At the galvanized connection bar at the front, yellow-red air couplings * 4 wheel chocks with holder on the front wall * 3-level wooden boards * Galvanized folding supports under the loading area chamfer * Holder for beacon at the rear of the trailer * Height-adjustable tarpaulin frame – approx. 3,960 mm * Galvanized front wall with tensioning mechanism for sliding curtains. Height-adjustable by approx. 400 mm * EDSCHA brand roof, sliding forward on ALU roof beam profiles (bolted with front and rear wall) * In the loading area 3 pairs of sliding stakes * Body can be hydraulically extended at the rear to the left and right by approx. 750 mm * Sliding roof with pivotable portal beam * Sliding tarpaulin with 700 mm excess length, with tension straps approx. every 600 mm. Height to top edge of body approx. 3,960 mm (loaded) Lredpfey Aug Dsx Akyjk * Driving with the sliding roof open is not permitted and will cause damage to the tarpaulin * Rear body closed with anodized ALU double-wing doors * Hook-on bar for ALU approach ramps at the rear of the vehicle * Control valves for hydraulic width extension located on the right-hand side of the trailer * White reflector tape according to EU regulations, red at the rear * Electro-hydraulic unit at the rear under the loading area * One mud flap at the rear of the trailer * European reflector boards (red-yellow) on the rear of the trailer * Hand

Condition: new, maximum load weight: 36,590 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Extract from the specifications. Full specification on request. Gooseneck: * Gooseneck with 45° beveled front corners and rear chamfer approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN) * Hardwood floor approx. 30 mm thick Loading platform: * Extendable loading platform with rear chamfer approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN) * 1 pair of flat-mounted lashing rings at the front of the platform (LC 10,000 daN) * Cut-outs in the outer frame of the platform for securing straps (LC 2,000 daN) * Hardwood floor approx. 48 mm thick, checker plate covering over the axles Tyres: * Tyres 245/70 R 17.5 3PMSF – Manufacturer of our choice. Load index (146/146F) TPMS: * TPMS tyre pressure monitoring system in accordance with ECE R 141. Data transmission to the tractor unit via the standardised EBS interface according to ISO 11992. For correct display, the tractor unit must be capable of transmitting and displaying this data. Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lift capacity (approx. 50 t test load) Axles: * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg per axle * Air suspension with lifting and lowering valve * Axle tool Brake system: * WABCO braking system in compliance with EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels. Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Lsdpfx Aoy Auifjkyork Electrical system: * Electrical system in accordance with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3), ASPÖCK-UNIBOX at the front connection strip with sockets 24N, 24S & 15-pin. Connection in accordance with ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Painting: * Complete steel structure automatically shot-blasted with centrifugal blasting machine after welding * Second blasting with corundum for optimum adhesion of the coating system * Final painting with 2 coats of 2K topcoat, single colour in RAL 3002 Carmine Red, as per RAL 841GL system * Rims in silver grey * Rear section metallised and painted in RAL 9010 (pure white) Accessories: * 2-inch king pin * One galvanized steel headboard approx. 400 mm high * Yellow-red air couplings on the galvanized connection strip at the front * One spare wheel holder in front of the headboard (without spare wheel) * Electro-hydraulic power unit * Remote rear axle steering, operated from the front and rear using cable remote control with push buttons, with axle track control (without installation in tractor unit) * Hook-on rail for aluminum loading ramps on gooseneck with integrated collision guard * At the gooseneck and rear plate, one bracket each side for warning boards, including socket * One bracket for a rotating beacon at the rear of the trailer * Galvanised folding supports under the rear slope of the loading platform * 1 pair of recessed lashing rings along the main beam, rear, in the chamfer (LC 10,000 daN) * Load manometer for determining axle loads, including load diagram * Non-slip sand coating painted on checker plates on gooseneck and loading platform * On the gooseneck, plug-in aluminium side and rear panels, approx. 2,440 x 400 mm (L

Condition: new, maximum load weight: 58,860 kg, overall weight: 73,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Extract from the equipment; complete equipment list available upon request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring approx. 30 mm thick Extendable loading platform: * Extendable loading platform with rear bevel approx. 500 mm x 8° * 8 pairs of fold-out lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, over the axles with checker plate Two-part steel ramps: * Pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 900 mm, with Super Grip rubber coating * Ramps with hydraulically folding ramp sections * Hydraulic lifting device, hydraulically adjustable * Maximum load per pair: 50,000 kg Lodey Augwepfx Akyjrk * In accordance with Regulation 1230/2012/EU, ramps shorter than 300 mm in transport position are not included in the overall vehicle length of 16,500 mm Axles: * BPW axles and suspension, 1st axle steering, 2nd and 3rd axles rigid, 4th and 5th axles trailing steering, air suspension with lift/lower function, drum brakes * Trailing steering axles with electromagnetic reverse lock, activated via reverse gear or manually * Technical axle load: 12,000 kg each Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141. Data is transmitted to the tractor unit via the standardized EBS interface (ISO 11992). For correct readout, the tractor unit must be capable of transmitting and displaying these data. Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, lifting capacity approx. 24 t (tested to approx. 50 t) Brake system: * Wabco brake system compliant with EU regulations, with EBS-E (4S3M), without connecting lines to the tractor unit Steel construction: * Steel structure made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations; 24 volt ASPÖCK-NORDIK lighting (ASS3) * All LED side marker lamps flash with the indicators * ASPÖCK-UNIBOX on the front connection rail with 24N, 24S, and 15-pin sockets as per ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Entire steel structure automatically blasted after welding using a centrifugal blasting machine * Second blasting step with corundum grit for optimal coating adhesion * HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final lacquer with 2 coats of 2-component topcoat, solid color RAL 3002 Carmine Red, compliant with the RAL 841GL system * Rear section metallized and painted RAL 9010 (Pure White) Including the following additional equipment: * 2-inch king pin * One galvanized steel front wall, approx. 400 mm high * One spare wheel holder in front of the front wall * Yellow-red air couplings mounted on the galvanized connection rail at the front * Bracket for beacon light at the rear of the trailer * Galvanized supports under the loading platform’s rear bevel * Super Grip 2 rubber coating

Condition: new, maximum load weight: 36,020 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our full vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Complete equipment details available on request. Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area with rear bevel approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) * 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate above the axles Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 3,185 + 1,420 x 1,250 mm, with grating covering C40/5 (point load approx. 2.8 t on a surface of approx. 20 x 20 cm) * Ramp with hydraulically foldable ramp sections and hydraulic lifting system * Maximum load per pair: 30,000 kg Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock activated via reverse gear and manually * Air suspension with raise/lower valve Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Brake system: * WABCO brake system compliant with EU regulations, with EBS-E (2S2M), without connection lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations, LED lighting 24V ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to guarantee optimum corrosion protection * Finishing coat: 2 layers 2K topcoat, solid colour RAL 3002 carmine red as per RAL system 841GL * Rear section metallised and painted RAL 9010 (pure white) * Rims in silver Included accessories: Lrjdpfx Akjy Auhujyjk * One bracket for warning signs on the gooseneck and at the rear left and right, including socket * 1 spare wheel holder under the loading area, right in the direction of travel * 2" kingpin * One galvanized steel front wall * Yellow-red air couplings on the galvanized front connection bar * 4 wheel chocks with brackets on the bulkhead * 3 height wooden boards * Galvanized folding supports under the loading area bevel * Bracket for rotating beacon at rear of trailer * Height-adjustable tarpaulin structure – approx. 3,960 mm * Galvanized front wall with tensioning system for sliding curtains, height adjustable by approx. 400 mm * EDSCHA roof, sliding forward on aluminum roof girder profiles (screwed to front and rear wall) * 3 pairs of sliding stakes in the loading area * The body is hydraulically extendable to the left and right at the rear by approx. 750 mm * Sliding roof with pivoting portal crossbeam * Sliding curtain with approx. 700 mm reserve length, ratchet straps at approx. 600 mm intervals. Height O

Condition: new, maximum load weight: 37,980 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete vehicle stock, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Complete equipment details available on request. Gooseneck: * Gooseneck with approx. 45° chamfered front corners and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood floor covering approx. 30 mm thick Loading platform (extendable version): * Loading platform in extendable version with rear chamfer approx. 1,000 mm x 8° * 6 pairs of lashing rings, foldable outwards (LC 5,000 daN) * 3 pairs of lashing rings, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings installed flat at the front of the loading platform (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) * Hardwood floor covering approx. 48 mm thick, checker plate over the axles Landing legs: * JOST landing legs (mechanical) with two-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Tires: * Tires 235/75 R 17.5 3PMSF – brand of our choice TPMS: * TPMS tire pressure monitoring system according to ECE R 141. Data transmission to the towing vehicle via the standardized EBS interface in accordance with ISO 11992. For correct display, the towing vehicle must be able to receive and show this data. Axles: * BPW axles and suspension, 2 fixed axles, 1 trailing steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated via reverse gear and manually * Air suspension with lifting and lowering valve * Axle tools Lredpfxoy Aufme Akysk Brake system: * Brake system according to EU regulations with EBS-E (2S2M), without connection lines to the tractor unit Steel construction: * Steel construction from high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Painting: * Entire steel structure is automatically shot blasted by blast wheel system after welding * Second blasting with corundum for optimal coating adhesion * Final coating with 2 layers of 2K topcoat, solid color in RAL 3002 Carmine Red, according to RAL system 841GL * Rims in silver-grey * Rear section metallized and painted in RAL 9010 (pure white) * Coating tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Electrical system: * Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK lighting (ASS3) * All LED side marker lamps flash with the indicator * ASPÖCK-UNIBOX on the front junction strip with 24N, 24S & 15-pin sockets, connection as per ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Accessories included: * 2-inch king pin * One galvanized steel front wall, approx. 400 mm high * One spare wheel holder in front of the headboard * Yellow-red air couplings on the galvanized front junction strip * 4 wheel chocks with holder at the headboard * Mounting at the rear of the gooseneck for ALU access ramps * Galvanized folding supports under the loading platform chamfer * Gooseneck and rear panel each with a bracket for warning signs including socket left and right * Axle load gauge including load diagram * On the gooseneck, plug-in aluminum side panels and rear wall, approx. 2,440 x 400 mm (L x H). The rear galvanized plug-in stanchions are removable. (Body length approx. 2,560 mm) * One galvanized toolbox, integrated in the chamfered gooseneck * 3 pairs of WADER C

Condition: like new (used), functionality: unexamined, roll diameter: 50 mm, roll width: 930 mm, roll pitch: 70 mm, total width: 1,000 mm, total height: 900 mm, total length: 15,000 mm, conveying length: 15,000 mm, construction height: 900 mm, machine base height: 200 mm, roll spacing: 90 mm, axle spacing: 90 mm, overall weight: 3,500 kg, working width: 1,000 mm, segment length: 3,000 mm, load capacity: 100 kg, Lippert roller conveyor with drive Unused Lsdpfx Ajxu Nggskyjrk 1x 6 m 1x 9 m Lenze gear motor 7 supports With control for forward and reverse, including emergency stop 16A plug