Used Cross Knife for sale (5,714)

Condition: good (used), Cross knife for meat grinder, robot knife -Cross knife: Robot knife 8 blades -Type: WK400 -Recording: 95 x 65 mm -Wolf size: WK400 -Material: knife steel Itsdpfx Adovwl Rwjkeg -Dimensions: Ø 375 x 60 mm -Weight: 9,4 kg

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Itjdsu Tg I Dopfx Adksg Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Condition: like new (used), Range (in depending on the lighting conditions) until: 15 m Iodpjd Ecncofx Adkotg Range with laser receiver: 30 m, & more 5 m: leveling accuracy +/-1 mm Self leveling range: 4° +-0,5 ° Accuracy of the horizontal line at 5 m: +-1.5 mm Accuracy of vertical line at 3 m +-0.75 mm Number of laser lines: 2 Weight: 485 g

Condition: good (used), STAHL T36/4 + knife Folding Machine for Pharmaceuticals Made in Germany. The world’s highest-class folding machine. The machine is ready for production. Smooth feed and folding speed adjustment. 4-cassette module + cross knife + delivery. Iodpfxjywdnyj Adkjtg Depp pile lift feeding (high stack) This machine is ideal for folding pharmaceutical leaflets thanks to its low fold and large number of cassettes. Cassette soundproofing. Electronic counter with a batching function and adjustable time between batches. Technical specifications: Max size: 360x550mm Min size: 80x100mm Weight: 450kg 380V power supply

Condition: excellent (used), Year of construction: 1994, Weinig 925 Rondomat profile knife grinder Stock code: 15443 Price: request for quotation $ Subcategory: Knife grinders Producer: Weinig Model: 925 Condition: used Tag number: 15443 Machine type: Grinding machines UMCC: G6775 Producer: Weinig Model: 925 Rondomat Year: 1992 Serial number: 925-438 Description: Weinig 925 Rondomat profile knife grinder We offer turnkey services with this machine. Printable page Itjdpfx Aen Ut Sledkog Get a quote General technical data Shaft length 9-1/2 inches Maximum tool diameter 9 inches Motor 1.5 HP, 220/440 V 8-7/8 Maximum wheel diameter Variable grinding wheel speeds: 1700, 2000, 2250, 2800 rpm Relief angle for back relief: 15 - 45 degrees Axial: 0 - 10 degrees Cooling liquid

Condition: used, functionality: fully functional, In this offer you buy a used trimmer "Canon 2-Knife Trimmer A1" Object of sale: 1 x Canon 2-knife trimmer A1 suitable for various Canon models. Condition: Itsdpfx Aowpd Tyjdkeg This offer is for a used device, which may show signs of use (minor scratches or yellowing). The device has been tested for function Packaging and dispatch: You are welcome to view the device during our business hours. Please make an appointment for this! Seaworthy packaging and worldwide shipping available on request! For further information you can of course also contact us personally.

Condition: used, functionality: fully functional, In this offer you buy a used 2-Knife Trimmer ‘SDD B4K/BT25 2-Knife Trimmer for Xerox’ Object of sale: 1 x SDD B4K/BT25 for various Xerox machines Counter readings: Total: Approx. 37,158 cuts Condition: This offer is a used device, which may show signs of use (minor scratches or yellowing). (minor scratches or yellowing). The device has been tested for function A test brochure can be seen in the photo Packaging and dispatch: You are welcome to view the device during our business hours. Please make an appointment for this! Iedpfeu S An Dox Adkstg Seaworthy packaging and worldwide shipping available on request! A function test will be recorded on video for you before dispatch or collection. For further information, you can of course also contact us personally.

Year of construction: 1987, condition: ready for operation (used), Knife grinders for 800 kofama lignum strips Sharpening bar 800 used 1987 Rating: Table Model: Itsdpfx Aoh S Upijdkeg 800 Description: 800 grinders with a slat knife

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery PERSONAL COLLECTION Cost of delivery Customer cover Startup type to be agreed Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net Itedpsfv Hphsfx Adkeg dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: 1.490,14, saw blade diameter: 500 mm, cutting height (max.): 140 mm, cutting width (max.): 350 mm, power: 8 kW (10.88 HP), overall weight: 2,000 kg, TECHNICAL DETAILS Max. saw blade length: 6,100 mm Max. saw blade diameter: 500 mm Saw blade arbor diameter: 35 mm Max. cutting height: 140 mm Max. cutting width: 350 mm Infeed table length: 7,850 mm Outfeed table length: 2,400 mm MACHINE DETAILS Main motor power: 5.5 kW Total power: 8.0 kW Voltage: 400 V Fuse: 25 A Dimensions & Weight Dimensions (L x W x H): 11,250 x 800 x 1,600 mm Weight: 2,000 kg EQUIPMENT Automatic feed system Itjdpfxey Nyd Is Adkeg

Condition: ready for operation (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: B725, cutting height (max.): 150 mm, cutting width (max.): 300 mm, table length: 3,000 mm, saw blade length: 3,570 mm, Equipment: CE marking, TECHNICAL DETAILS Max. saw blade length: 3,570 mm Max. cutting width: 300 mm Max. cutting height: 150 mm Max. saw blade diameter: 500 mm Saw blade arbor diameter: 35 mm Infeed table length: 3,000 mm Outfeed table length: 3,000 mm MACHINE DETAILS Voltage: 400 V Itodey Nxynspfx Adkog Fuse: 16 A Power: 5.5 kW Main motor power: 5.5 kW Dimensions & Weight Dimensions (L x W x H): 3,900 x 1,100 x 1,650 mm Transport weight: 700 kg Transport packages: 3 EQUIPMENT CE marking

Condition: excellent (used), Year of construction: 2019, operating hours: 1,000 h, functionality: fully functional, machine/vehicle number: 8135.44, cutting height (max.): 100 mm, cutting depth: 300 mm, Great saw always cuts to 0.5 for age hardy used Itsdpfxsyngnie Adkog

Condition: used, Year of construction: 2004, functionality: fully functional, We are offering this used WEINIG Dimter OPTICUT S75-4 cross-cut saw line optimization system, manufactured in 2004, for sale. Manufacturer: WEINIG Dimter Model: OPTICUT S75-4 Itjdpjy S T Uxjfx Adkog Year of manufacture: 2004 Condition: used Category ID: 171 Type ID: 2446 Type: cross-cut saw line optimization system If you have any questions or would like more information, please do not hesitate to send us a message or call us.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2026, volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Isdpfx Aoy S Ru Aedkjtg Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 2004, Format: 310 x 430 mm Equipment: Counter 22 Mio Co-Pilot with Touchscreen Infeed conveyor from the right Automatic Magazine for In-line Production Counting Stacker Product Counter Tool Presetter Total number of knife sets: 1 Itedoy Tacxjpfx Adkeg Interchangeable Cutting Cassettes (Standard Set)

Condition: used, band length ca. 1.700 mm + 2.700 mm cutting width max. 2.500 mm Cutting height max. ca. 80 mm Ijdsv Hgb Njpfx Adkotg

Condition: new, Year of construction: 2026, Sharpening woodworking tools The PROFI chisel (lancing bag) and planing knife grinding machine! No cheap ASIA copy! The original! WOOD-TOOL-GRINDER WTG-1 - «Swiss Currently the absolute cheapest PROFI wood tool grinder on the market! For a precise and efficient work, a perfectly ground, razor-sharp cutting edge is a must. With our grinder sharpen your tools like: «Chisels, plow blades, chisels, chisels» fast, simple, accurate and inexpensive ... Made in Switzerland = Swiss Quality Where is the WOOD-TOOL-GRINDER «WTG-1» used? - Where conventionally wood is processed. - For example, in carpentry, carpentry, - carpentry, schools, trade schools, - Training centers / training workshops ... Your advantages - Very precise, stable and stable construction - Fast, in just 30 seconds you grind a perfect flashless edge - Extremely easy to use, also for apprentices and unskilled workers - Dry grinding principle, i. no problems with moisture (water / oil) - Stepless cutting angle adjustment - You buy fewer new tools, thus lower maintenance and fixed costs Construction of the wooden tool grinding machine «WTG-1» The WTG is powered by a powerful 500 watt motor. The carriage used is a dust-proof, high-precision, ball-bearing profiled rail guide, which is used a thousand times in machine tools, industrial robots and precision special purpose machines. Stepless grinding is achieved by means of an accurate and self-locking dovetail. The tool clamping is safe and stable via a parallel clamping system. Technical specifications Weight: 20 kg Connection: 230 volts Motor: 500 watts Speed: 3000 rpm Grindable tool width: 5 - 60 mm Cutting angle adjustment: 25 - 30 ° degrees stepless Main grinding wheel: special corundum Ø 100 mm Polishing wheel / buffing wheel: special type ROTAX Ø 150 mm I would recommend you the basic machine and the grinding double set. So you are well prepared. Your direct contact person: Itodpfx Adjdt Ap Askjg Sir Marc Brönnimann Head of Sales & Assembly BST Kaindl, DAREX, HARICH, Vertex, Drill Doctor, METEOR, Optima, Tatar, Promac, Cuoghi, Avyac, Christen, MOTOM, VITAX, WASU, Ulrich Klingel, ISELI, Schneeberger, Lamallo,

Condition: excellent (used), Gockel G130PL x 5100mm Vertical Spindle Knife Grinder Manufacturer Gockel Model G130PL x 5100mm Itedpfsy N Amfjx Adksg Year 1980 Condition Used Serial Number 5908 Stock Number 2602 Mag Chuck 800mm x 5100mm Segmental wheel 1000mm dia Wheel/Spindle Drive 185KW / 248hp Additional Features Year 1980 Travelling Wheelhead New Stones for Wheel Power rise and fall to wheelhead Auto down feed to wheelhead Marpos Sizing Coolant pump and separator

Condition: used, Year of construction: 2001, total height: 1,600 mm, total length: 1,300 mm, total width: 1,350 mm, - Year: 2001 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 24.095.2 - Transport dimensions: 1300mm x 1350mm x 1600mm (l x w x h) Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Itodpfx Adswnilrskjg Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), Year of construction: 1996, functionality: fully functional, grinding length: 240 mm, type of input current: three-phase, working width: 240 mm, Weinig Rondamat 925 Year of manufacture: 1996 Maximum tool width: 240 mm Grinding wheel diameter: 150-225 mm Grinding wheel bore: 60 mm Tool diameter: 100-230 mm Itsdjy Azaqopfx Adkog

Condition: used, Year of construction: 2026, operating hours: 10 h, functionality: fully functional, machine/vehicle number: 2026-078, working width: 1,600 mm, working height: 100 mm, cutting width (max.): 1,600 mm, number of slots in tool magazine: 2, Used machine CNC cutter/plotter Cutting area in X and Y: 1,500 x 1,600 mm. Multifunctional CAM cutting system in CNC knife technology for 2D cutting of leather, fabric, technical textiles, foam and other flat, semi-flexible or rigid, non-metallic materials Equipment of the used machine. • 1 cutting bridge and 1 Multifunctional tool head • max. material height 100 mm • Multifunctional tool head to hold 2 interchangeable tools • powerful vacuum blower for fixing the material • Standard equipped with gray conveyor table (Conveyor). Can be extended with other tools (on request): • EOT electric oscillating blade • POT pneumatic oscillating knife • PRT rotating blade Iedpewgc I Rofx Adketg • UCT universal blade • KCT Kiss-Cut tool • CTT creasing tool • V-Cut angle-cut cutting blade • Punching tool for pinches or holes • Printer mark detection • Camera registration • Milling Head + exhaust Easy-to-use function • Easy interchangeable cutting tools, "PLUG & CUT • Intuitive user interface • Easy blade change • Vacuum zones can be activated with a click Fast amortization • Low cost with high added value • Best material utilization through nest expert software modules (not included in equipment) • High velocity • Constant precision Data: • Short cutting times due to high positioning speed up to 90 m/min. • Repeatabiliy +/- 0.25 mm • Cuts single or multiple layers • Suitable for both single ply and multi ply or sheet goods and roll goods (can be extended with suitable unwinder) (Product photo as example) The machine is CE certified.

Condition: used, Year of construction: 2026, operating hours: 15 h, functionality: fully functional, machine/vehicle number: 204065, Used machine CNC cutter/plotter Cutting area in X and Y: 2,500 x 2,100 mm. Multifunctional CAM cutting system in CNC knife technology for 2D cutting of leather, fabric, technical textiles, foam and other flat, semi-flexible or rigid, non-metallic materials. Equipment of the used machine • 1 cutting bridge and 1 multifunctional tool head The machine is sold with one driven circular knife, electric oscillating knife and one Milling Head + exhaust • Multifunctional tool head to hold max. 2 interchangeable tools • powerful vacuum blower for fixing the material • Standard equipped with gray conveyor table (Conveyor). Green-blue exchange conveyor possible (offers high contrast for dark materials) Can be extended with other tools (on request): • EOT electric oscillating blade Itodpfxsif Ek Rj Adkog • POT pneumatic oscillating knife • PRT rotating blade • UCT universal blade • KCT Kiss-Cut tool • CTT creasing tool • V-Cut angle-cut cutting blade • Punching tool for pinches or holes • Printer mark detection • Camera registration Easy-to-use function • Easy interchangeable cutting tools, "PLUG & CUT • Intuitive user interface • Easy blade change • Vacuum zones can be activated with a click Fast amortization • Low cost with high added value • Best material utilization through nest expert software modules (not included in equipment) • High velocity • Constant precision Data: • Short cutting times due to high positioning speed up to 90 m/min. • Repeatabiliy +/- 0.25 mm • Cuts single or multiple layers • Suitable for both single ply and multi ply or sheet goods and roll goods (can be extended with suitable unwinder) (Product photo as example) The machine is CE certified.

Condition: as good as new (ex-display), Year of construction: 2026, operating hours: 15 h, functionality: fully functional, machine/vehicle number: 2002-045, Used CNC cutter/plotter Cutting area in X and Y: 2,500 x 2,100 mm Multifunctional CAM cutting system with CNC knife technology for 2D cutting of leather, fabric, technical textiles, foam, and other flat, semi-flexible, or rigid, non-metallic materials Equipment of the used machine: • 1 cutting bridge and 1 multifunctional tool head The machine is sold with a CCD camera for detecting print marks • Multifunctional tool head for holding 2 interchangeable tools • Powerful vacuum blower for fixing the material • Equipped with gray conveyor belt table as standard. Green-blue replacement conveyor available (provides high contrast for dark materials) Additional tools are available (on request): • EOT electric oscillating knife • POT pneumatic oscillating knife • PRT driven circular knife • UCT universal knife (pull knife) • KCT kiss-cut tool • CTT creasing tool • V-cut angle cutter • Printer mark recognition • Camera registration • Punching tool for notches or holes • Milling cutter with suction device User-friendly • Easily replaceable cutting tools, “PLUG & CUT” • Intuitive user interface • Easy blade replacement • Vacuum zones can be activated with a click Fast amortization • Low costs with high added value • Optimal material utilization thanks to nest expert software modules (not included in the equipment) • High speed • Consistent precision Itedpsfnlkwefx Adkjg Data: • Short cutting times thanks to high positioning speed of up to 90 m/min • Repeat accuracy +/- 0.25 mm • Cuts single or multiple layers • Suitable for both sheet material and roll material (can be expanded with a suitable unwinder) • Fast amortization (Product photo as an example) The machine is CE certified.

Condition: used, functionality: fully functional, This listing is for a second-hand Canon accessory: the ‘Canon 2-Knife Trimmer A1’ Compatible with various Canon imagePRESS models Condition: Ijdpfsy R Nn Sjx Adkotg This is a second-hand item, which may show signs of use (minor scratches or discolouration). The device has been tested for functionality Packaging and shipping: You are welcome to view the device during our business hours. Please arrange an appointment for this! Sturdy packaging and worldwide shipping available on request! A functionality test will be recorded on video for you prior to dispatch or collection. For further information, you are of course welcome to contact us directly.

Condition: good (used), Drilling machine, bench drill, pillar drill, column drill, box-type drill, tapping machine, threading machine -Manufacturer: Strands, MK3 bench drill with cross table Demanders Ijdpfx Adsy Rx Egskjtg -Motor: 0.75/1.0 kW -Speeds: 100 - 30200 rpm, 8-stage forward/reverse rotation -Thread cutting device: via foot switch -Table size: 500 x 195 mm -Cross table travel: X360 mm Y160 mm Z440 mm -Spindle mount: MK3 -Spindle stroke: 135 mm -Protrusion: 255 mm -Dimensions: 780/800/H1540 mm -Weight: 218 kg