Used Mütek Hawk-Eye for sale (3,300)

Condition: new, Year of construction: 2026, Extremely powerful industrial magnet for iron separation Special price: €990 net (shipping €14.90 net) *Construction lengths can be found in image 2 The active side is equipped with a stainless steel end plate (material 1.4301). Ijdpfx Agstqfhxo Aotn Threaded holes are provided on the rear side for mounting; *handle available on request The block magnet systems can be used at temperatures of up to max. +100°C operating temperature. The magnet surface should be cleaned regularly from captured iron parts. Pickup distances for all types, for example: For a steel nut M5: approx. 60 mm For an M5 x 30 screw: approx. 100 mm Mounting example 1: Mounted above a conveyor belt, 'iron parts jump onto the holding surface of the magnet.' Mounting example 2: Mounted within a pipeline system with direct contact to the material flow. For maximum separation safety, a cascade setup of multiple block magnets in series is possible. Assembly and safety instructions: When handling, already upon unpacking and later during installation, ensure that there are no loose iron parts, such as tools or screws, nearby. The magnetic force is so strong that painful injuries may occur if fingers get caught between iron parts and the active surface. There should be no steel parts under the active surface within a minimum distance of 400 mm.

Year of construction: 2026, condition: new, *Only the neodymium overbelt magnet is offered, not the conveyor belt underneath. *Neodymium magnets are among the strongest magnets in the world. They have an extreme pulling power and cannot be compared to ferrite magnets. Extremely high degree of separation, depending on the bulk height and the starting material. Probably the most compact overband magnet on the market. The competition often uses the less powerful ferrite magnets to save costs. dimensions approx. Length: 104cm Width: 22cm Height: 28 cm (at the motor) *Without controller Itodpfx Asdubpuog Aon Surcharge for simple manual start/stop control + 495 € A high-performance industrial neodymium magnet is installed. High-performance neodymium magnet approx. 600x68x36.5 mm * So nails are attracted to a length of 600 mm and thrown off to the side, in the area that is no longer magnetic. This overbelt magnet should be mounted approx. 5 - 9 cm above the material flow. *Assembly/suspension on site Ideal for separating nails from wood chips. Optionally also in a single-shaft shredder that is sucked off Requirements: *Your belt width or useful width inside (of the existing conveyor belt) should ideally be narrower than 55 cm *Suitable for separating nails from material flows that are less than 12 mm high and with a chip length of less than 25 mm. ----- Optional at extra charge: Cross and ascending belt demonstrators from € 7,995 net

Condition: new, Year of construction: 2026, Diameter: 160mm Also available in the diameters: 180, 200, 250, 300 mm for an additional charge, other diameters on request. Very stable industrial design. Ideal for separating nails/metal parts from material flows. For example after a wood shredder. including 3 extremely powerful magnets * If desired, up to 6 magnets can be installed in the component - surcharge for each additional magnet + 49 € Iodpochuvrefx Ag Astn - Neodymium magnets are also available instead of ferrite for an additional charge Your advantages: + Extremely large inspection door with seal for easy stripping of the nails + Stable quick-release fastener +Made in Germany Inspection door / opening: 35x18 cm Installation length may vary

Condition: used, Year of construction: 2025, functionality: fully functional, type of input current: AC, overall weight: 1 kg, Equipment: documentation/manual, type plate available, For sale is a ZEISS T-Scan Hawk 2, a high-precision optical 3D scanner for demanding measurement and inspection tasks. Ideal for precise 3D measurements in industry and research, especially when measuring components in challenging environments. Fast application, easy operation. Condition: Lightly used, primarily for trade shows, exhibitions, and training purposes. Scope of delivery: · T-Scan Hawk 2 Lite · Blue Class 2 laser, eye-safe (IEC 60825-1:2014) · Weight: < 1 kg · Calibration plate (DAkkS calibrated) · Sensor cable · Transport case · Incoming inspection at our facility with sphere bars according to ISO 10360 · Acceptance certificate with proof of traceability · ZEISS INSPECT OPTICAL 3D Free · Sensor driver T-SCAN Hawk 2 ZEISS INSPECT OPTICAL 3D Free · Open and edit new and existing projects · Import of point clouds, polygon meshes Iedjzyp Stjpfx Ag Aotn · Creation, editing and processing of polygon meshes · Element construction: regular geometries, points, sections, curves, surfaces, dimensions · CAD import of standard formats IGES, VDA, STEP, JT Open, STL, PLY · Application of common alignment methods · Comparison against CAD with colored deviation display · Dimensioning and form/position evaluations according to ISO GPS and ASME Y14.5 · Report module Sensor driver T-SCAN Hawk 2 · Setup and calibration · User-guided calibration · Measurement data acquisition and project management · Configurable workflow assistant

Condition: ready for operation (used), Year of construction: 2021, operating hours: 20 h, functionality: fully functional, machine/vehicle number: SK02UXKP0365, measuring range X-axis: 550 mm, measuring range Y-axis: 600 mm, Auction of a Zeiss T-Scan Hawk with only 20 operating hours! TECHNICAL DETAILS Maximum measuring range: 550 mm x 600 mm Measuring accuracy: 0.02 mm + 0.035 mm/m MACHINE DETAILS Laser class: Class 2M (eye-safe) according to IEC 60825-1:2014 Operating hours: 20 EQUIPMENT Notebook GOM Inspect software Itjdjx Sqfnjpfx Ag Aon

Condition: good (used), Year of construction: 2016, functionality: fully functional, machine/vehicle number: 665182, travel distance X-axis: 650 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 500 mm, feed rate X-axis: 30 m/min, feed rate Y-axis: 30 m/min, feed rate Z-axis: 30 m/min, total height: 2,850 mm, total length: 3,300 mm, total width: 2,400 mm, overall weight: 9,000 kg, spindle speed (max.): 42,000 rpm, number of slots in tool magazine: 40, Equipment: documentation/manual, OPS INGERSOLL SPEED HAWK 650 CNC machining center - Important note: the spindle was replaced in 2025 for approximately EUR 40,000, resulting in very few spindle operating hours! - Pallet dimensions: approximately 320 x 320 mm - The pallets are clamped onto the rotary table - Tool holder: HSK-E 40 - For further technical data, see the images - With technical documentation - With HSK-E 40 tool holders and three pallets Itedpfx Aey Tvcueg Asn Attention: The item must be picked up between July 21st and July 23rd, 2026, on a date to be confirmed. FCA D-73529 Schwäbisch Gmünd - loaded onto a truck

Condition: new, Year of construction: 2026, Your advantages: + extremely large cutting unit opening with 1300x1200mm + special rotor suitable for hardwood and softwood + Energy-efficient and powerful with 37 kW at start-up Technical specifications: Colour: grey / blue Feed opening (mm): 1,300 x 1,200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Power requirement (kW): 37 Screen perforation (mm): 30 - 50 mm - selectable Tools: 37/70 knives Extraction nozzle Ø (mm): 200 mm Dimensions: 2430x2410x1735 mm (lxwxh) Weight (approx. Kg): 3,920 Optional for a surcharge: * to shred veneer or paper (anything thinner than 3 mm) - we recommend a segment floor. The machine in preproduction has not yet installed this. Special option at an additional cost. - 2nd row of knives, for up to 30% more throughput Itjdpfsgbkkrjx Ag Asn - Fast hydraulics, for increased throughput - Preparation for conveyor belt removal - conveyor belt - HAWK-EYE overbelt magnet --- Optimal pallet size with the option slide extension = 1200x1400 (option slide extension, the cutting unit opening 1300x1700 surcharge + 12,975.00) * is associated with significantly longer production time. * larger machines on request --- Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear

Condition: used, functionality: limited functionality, The following are offered: OPS 550 (3-axis): Tool changer with 32 positions for HSKE 40 Robot positions for the Erowa clamping system: 70 positions (workpiece changer) Robot positions for pallet changing: 8 positions The robot is currently not in operation due to a fault. However, this can be repaired so that it functions normally again. Itjdpfx Agezzavrj Asn

Condition: like new (used), functionality: fully functional, Year of construction: 2025, operating hours: 55 h, Machine with special rotor available immediately Advantages: + special rotor with reduced blade overhang, suitable for hard and soft materials + 22 kW motor Itjdpex Af Rdjfx Ag Asn + effective square blades *for pallets: up to a maximum of 10 pallets per hour *dependent on screen size and material. With smaller wood residues, significantly more. Motor: 22 kW; 400 V - 50 Hz - 3 phase, Screen: 15/20 mm or as agreed (10 to 40 mm possible) hydraulically operated slide Screen opening currently (15/20 mm) *can be exchanged Extraction nozzle Ø 200 mm. Feed opening 1000x1000 mm Dimensions: 2000x1800x1645mm Example image above: color of the system may vary Weight: 1920 kg. Included as standard: - Control cabinet with PLC control - automatic star/delta start - fast hydraulics - auto. OFF when the rotor is idle - speed 70-90 rpm for high throughput - cycle control to avoid idle times - performance-enhancing step control of the hydraulic slide - Pertinax guides for hydraulic slide - vibration-damping machine feet - CE compliant The following options are available at an extra cost: - Raise shredder by 30 cm (preparation for conveyor belt) + €2,480 net - Inclined conveyor belt (discharge height approx. 220 cm) + €12,980 net - Overband magnet + €6,980 net - Control for conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the shredder) - extended feed hopper 1500x1500 mm + €3,480 net Requirements for the raw material: - The moisture content (as received) must be below 25% - The feed must be free of metals and mineral contaminants. Damage to the tools and/or increased wear may result.

Year of construction: 2024, condition: new, Overview - of the various variants *not every item is required: Optional: - Bale opener MHB from €24,990 net - Straw mill MHZ from €7,980 net - Special hopper €970 net - Cyclone from €3,750 net Itodpfx Aoff Sbiog Asn - Sheet metal silo demonstrator with discharge (only shown schematically in the picture) *optional, if you want to feed it with a wheel loader Individual price net from €14,750 - demonstrator - Dust extraction auger - length approx. 4 m Four sieves are mounted on the underside, which are vacuumed. Individual price net from: €9,750 - Suction parts / hoses as a package €945 net - Control system for the entire system Individual price net: €2,750 - Demonstrator dust extraction unit MMJET 160, with cleaning Connection 160, Fan 2.2kW Air flow 1850m³ /400 V Automatic compressed air cleaning Individual price net from: €6,950 - Bale press B 400 Bales approx. 400x400x800 (height adjustable) Up to 30 bales per hour with +/- 20 kg from €67,550 net *A reference system (baler) is located in postal code: 64579 Gernsheim Technical data: Bale size (W x D x H): 400 x 400 x 800 (height can be adjusted on request) Weight of the bale +/- 20 KG (material-dependent) Performance: approx. 30 bales per hour Hopper capacity approx. 0.7m³ Level sensors for min./max. fill level in the hopper Hydraulic pre-compressor Hydraulic press ram Hydraulic unit, valve block with oil tank Pump 18.5 kW / 50 liters Rollers in the press channel for easy bale discharge Dimensions (L x W x H) 3105x2830x2455 mm Weight approx. 1500 KG mütek balers / packaging machines have been developed for the production of bales from a wide variety of materials, such as shredded Miscanthus or elephant grass, wood chips, sawdust and shredded straw. The machine is characterized by a robust design, which guarantees consistent quality in continuous operation. The baler compresses the material fed into the hopper without the addition of binding agents by means of hydraulic pressure and packages the material in plastic sacks. The volume of the material can be significantly reduced with the baler. The volume reduction rate depends on the material. The maximum material moisture content must not exceed 18% dry matter. The hopper of the mütek baler can be loaded automatically or by hand and has a volume of approx. 0.7 m³. Containers with a larger volume or with an integrated extraction and filter system as a complete disposal unit are also available. In addition to the automatic filling via dust extractor, mütek also offers filling by means of conveyor screws. In both variants, automatic dust extraction is possible. mütek balers are equipped with a control cabinet for operation. In the standard version, the dimensions of the bales (width x depth x height) are 400 x 400 x 800 mm. However, the height can be adjusted to your requirements on request. The following advantages result from the production of bales: - Simple and safe storage - No loose dust - Minimization of storage volume - Low transport volume *Requirements for the raw material: - dry (max. 30% dry matter) - maximum 35 mm long

Condition: used, Year of construction: 1999, functionality: fully functional, Equipment: documentation/manual, Cincinnati Hawk machining center 2 axes: X and Z Itsdpfxsz I Tf Do Ag Aon CNC: GE Fanuc Series 21i-T Year: 1999 Chip conveyor: included Documentation: included Video available Inspection possible

Condition: as good as new (ex-display), Year of construction: 2023, Ideal for shredding polystyrene or similar materials. Throughput is highly dependent on the screen and the input material: - up to 60 kg/h for EPS with a 15 mm screen *the coarser the screen, the higher the throughput. Motor 9.2 / 11 kW - 400 Volts, sturdy steel construction, hardened cutting blades, screen with interchangeable inserts, optional hole sizes: (8), (10), 15, 22, 26, 30, 40, or 60 mm with electric drive, star-delta starter, overload protection, and 8 m power cable, ready for connection, discharge nozzle 150 mm, Isdeh S H T Uopfx Ag Aotn optional for plastic or corrugated pipes, blowing distance approx. 12 m, chassis with 2 running wheels Ø 380 mm, and one swiveling support wheel Ø 125 mm, all wheels with solid rubber tires, dimensions approx. 1200 x 900 x 1270/1400 mm (l x w x h) weight approx. 240 kg, Spare parts prices and options: 24 hardened blades, €9.90 each (net) 6 bolts, €14.90 each (net) 1 screen, €475 (net) 1 cover, €290 (net)

Condition: reconditioned (used), Year of construction: 2023, Special price for a machine with low usage Base machine: €29,990 net Options available at an extra charge: - Cooling unit: €3,995 net - Emulsion tank: €3,990 net The hydraulic briquetting presses of the MPP NEM series compress materials such as aluminum, copper, brass, bronze, graphite, and other non-ferrous metals into dimensionally stable cylindrical briquettes. The machines are characterized by a robust design that guarantees consistent briquette quality in continuous operation. The pressing process takes place without the addition of binders, solely through hydraulic pressure. The volume of the raw material can be reduced by up to 90%, depending on the material. Throughput: up to a maximum of 70 kg/h (material-dependent), Briquette diameter: Ø 50 mm, Motor: 5.5 kW, 400 volts / 50 Hz / 3-phase, Pump: 40 liters, . Maximum briquette length: 50 mm, Optional briquette length: 40 mm, Silo diameter: 1,000 mm, Oil tank: 110 liters. . Dimensions: 1750x1130x1100 mm (l x w x h) Weight: 950 kg. . Hydraulic pre-compression via slide valve Main press cylinder Vertical cylinder . Itsdpfx Agsd N Dnho Aon Level sensor: yes . Requirements for the raw material - Max. chip length: 15 mm - Installation temperature: temperature-controlled room at a minimum of +5°C - Max. weight on the agitator: 150 kg - The feed must be free of magnetic metals and mineral contaminants such as sand, stones, etc. Damage to the pressing tools and/or increased wear may result.

Condition: ready for operation (used), Year of construction: 2016, operating hours: 152 h, functionality: fully functional, machine/vehicle number: 665182, travel distance X-axis: 650 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 500 mm, spindle speed (max.): 42,000 rpm, number of slots in tool magazine: 40, No minimum price – guaranteed sale to the highest bidder! Submitting a bid obligates you to collect the item within the period from September 21st to October 1st! Spindle replacement for €40,000 in 2025! Since then, only approximately 150 spindle operating hours! TECHNICAL DETAILS Travel range X-axis: 650 mm Travel range Y-axis: 550 mm Travel range Z-axis: 500 mm Feed rates Feed rate X-axis: 30 m/min Feed rate Y-axis: 30 m/min Feed rate Z-axis: 30 m/min Spindle Spindle mounting: HSK-E 40 Spindle speed: 42,000 rpm Spindle operating time: 151 h 20 min 08 s Spindle replacement: 2025 Cost of spindle replacement: approx. €40,000 Tool magazine Number of tool positions: 40 Pallet system Pallet dimensions: approx. 320 × 320 mm Pallet clamping: Rotary table MACHINE DETAILS Itjdpfx Agsz Aplxo Aen Mains voltage: 400 V Mains frequency: 50 Hz Control voltage: 24 V DC Maximum fuse rating: 63 A Connected power: 38 kVA Dimensions and weight Overall height: 2,850 mm Overall length: 3,300 mm Overall width: 2,400 mm Machine weight: 9,000 kg EQUIPMENT - Technical documentation - Manual - HSK-E 40 tool holders - 3 pallets External reference: Demo - Lot 5

Condition: excellent (used), Year of construction: 2022, operating hours: 50 h, functionality: fully functional, machine/vehicle number: SK02UXKP0579, measuring range X-axis: 550 mm, measuring range Y-axis: 600 mm, overall weight: 1 kg, repeat accuracy: 0.02 mm, Equipment: documentation/manual, ZEISS T-SCAN hawk metrology laser 3D scanner with accuracy 0,02mm + 0,035mm/m with 3 scanning modes (Standard - 7 red crosses, Fine - 5 blue lines, Single red line for deep holes). Manufacturing year 2022. Fully functional and ready to use. Included: 3D scanner Calibration panel Powerful Dell mobile workstation still under Dell Pro Support Warranty Software GOM/ZEISS Inspect 2021 licence on USB drive Iedpfx Ageyxy Sdj Aotn Rigid travel case Laptop bag All original documentation included Inspection under working conditions possible. ZEISS INSPECT 2021: • Opening and editing new and existing projects • Import of point clouds and polygon meshes • Creation, editing, and processing of polygon meshes • Construction of elements: basic geometries, points, sections, curves, surfaces, dimensions • Import of CAD data in standard formats: IGES, VDA, STEP, JT Open, STL, PLY • Use of common alignment methods • CAD comparison with color deviation mapping • Dimensioning and evaluation of form/position according to ISO GPS and ASME Y14.5 • Reporting module Delivery

Condition: ready for operation (used), Year of construction: 2004, spindle speed (max.): 4,500 rpm, travel distance X-axis: 215 mm, travel distance Z-axis: 440 mm, controller manufacturer: FANUC, controller model: 21i-T, number of slots in tool magazine: 12, number of axes: 3, This 3-axis Cincinnati HAWK 200 was manufactured in 2004. It features a turning length of 500 mm and a maximum turning diameter of 250 mm. The machine is equipped with a FANUC 21i-T CNC control and has a turret capacity of 12 tools. If you are looking to get high-quality turning capabilities, consider the Cincinnati HAWK 200 CNC lathe we have for sale. Contact us for further details. Itodpfsz N A U Sjx Ag Ajn • Turning length: 500 mm • Maximum turning diameter: 250 mm • Swing over bed: 400 mm • Swing over cross slide: 380 mm • Spindle bore: 63 mm • Driven tools: Yes, 6 driven tools Technical Specification Counter Spindle Yes Driven Tools Yes

Condition: new, Year of construction: 2025, Another machine immediately available! Itedpfjv Rpxlsx Ag Asn Briquetting press with PLC control and automatic briquette length adjustment Throughput: up to max. 60 kg/h Briquette: 50 mm cylindrical Motor: 5.5 kW Dimensions: 1,900 x 1,350 x 1,410 mm Weight: approx. 860 kg Requirements: Feed material should ideally be shorter than 25 mm chip length Moisture content 6–12% ATRO Machine suitable for intermittent operation. E.g. briquetting for up to 2.5 hours; 1 hour break, etc. If the machine needs to run longer than 2.5 hours continuously, optional cooling must be connected.

Condition: as good as new (ex-display), Year of construction: 2024, The ideal machine for shredding cables, including optimized cutting geometry, approximately 9 operating hours. Motor: 18.5 kW; 400 V - 50 Hz - 3 phase, Knives: 14 pieces, 40x40mm, multi-rotatable, Rotor diameter: 260 mm, Control: Omron PLC, Cutting chamber opening 600 x 800 mm, Hopper volume approx. 0.6 m³, Hydraulically actuated slide Screen size optional (15 - 40mm) Extraction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (l x w x h) approx. 1737 x 1167 x 1650 mm The following options are available at an additional cost: - Double knife row + €1,990 net (28 instead of 14) - Surcharge for 4-sided segment base + €2,170 net (prevents the slide from jamming. Recommended when shredding plastics, paper, veneer with a thickness of less than 3 mm). - Raise shredder by 30 cm (preparation for conveyor belt) + €1,980 net - Inclined conveyor belt (discharge height approx. 220 cm) + €8,770 net - Over-band magnet + €6,980 net - Control for conveyor belt and over-band magnet + €2,750 net (Start and stop synchronized with the shredder) Ijdpsgmfa Ajfx Ag Ajtn Bea9ia3l27 Requirements for the raw material: - Mineral impurities such as sand, stones, etc. lead to increased wear. We would be happy to offer a free test with your material. We invite you to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material by freight forwarder and we will document the test with photos and videos.

Condition: as good as new (ex-display), Year of construction: 2024, Special price: €29,970 net Itedpfsgmh H Tjx Ag Asn One machine is currently available for immediate delivery. This machine is ideal for shredding bulky, lightweight aluminum chips or turning chips. Not suitable for heavier aluminum parts. Included: + Optimized cutting geometry + Adapted slide control + Load-dependent controlled hydraulic slide (which presses the chips against the cutting mechanism) Motor: 18.5 kW; 400 V - 50 Hz - 3 phase Knives: 40x40mm, multi-rotatable Rotor diameter: 260 mm Control: Omron PLC Cutting mechanism opening: 600 x 800 mm Hopper volume: approx. 0.6 m³ Hydraulically actuated slide Screen size selectable (15 - 40mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (l x w x h) approx. 1737 x 1167 x 1650 mm The following options are available at an extra cost: - Raise the shredder by 30 cm (preparation for conveyor belt) + €2,990 net - Inclined conveyor belt (discharge height approx. 220 cm) + €9,770 net - Overband magnet + €6,980 net - Control for conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the shredder) We would be happy to provide a free test with your material. We invite you to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via a freight forwarder, and we will document the test with photos and videos.

Condition: used, Year of construction: 2021, Canon CX-1 system, including computer, packed in its original manufacturer’s boxes. Serial number: 210141 – Year of purchase: 2022 Itodpfx Agozmxqrs Aon The system was purchased for a brief clinical study and has seen very limited use; it is in excellent condition.

Condition: ready for operation (used), Year of construction: 2009, operating hours: 4,247 h, functionality: fully functional, machine/vehicle number: 655118, travel distance X-axis: 550 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 400 mm, spindle speed (max.): 42,000 rpm, swivel angle A-axis (min.): -120 °, swivel angle A-axis (max.): 60 °, No minimum price – guaranteed sale to the highest bidder! Itodpfx Aszquprjg Asn Submitting a bid obligates you to collect the item on time between September 21st and October 1st! TECHNICAL DETAILS Travel range X-axis: 550 mm Travel range Y-axis: 400 mm Travel range Z-axis: 400 mm Swivel angle A-axis: -120° to +60° Swivel angle C-axis: n x 360° Distance from HSK-E tool holder to table: 450 mm Clamping area: 650 x 800 mm Pallet dimensions for 4th and 5th axes: approx. 300 x 300 mm Spindle Spindle mounting: HSK-E 40 Spindle speed: 0 to 42,000 rpm Spindle power S1: 15 kW Spindle power S6: 17 kW Axes and Accuracy Drive type: Digital AC servo motors, fully synchronized Travel speed: max. 30 m/min Acceleration: max. 15 m/s² Repeatability: 0.002 mm Digital display: 0.001 mm or 0.0001 mm, selectable Nominal speed in NC axis operation A-axis: 40 min⁻¹ Nominal speed in NC axis operation C-axis: 40 min⁻¹ Tool Changer Type: Pick-up disc magazine Magazine slots: 32 MACHINE DETAILS Machine operating time: 484 d 11 h 24 min 06 s Spindle operating time: 4,246 h 55 min 36 s Type: 5-axis CNC machining center Connected load: 38 kVA Input voltage: 400 V AC, 3-phase, 50 Hz Control voltage: 24 V DC Fuses: max. 63 A Overall length: 3,300 mm Overall width: 2,200 mm Overall height: 2,300 mm Machine weight: 7,400 kg EQUIPMENT - Technical documentation and manual - Three spare pallets - HSK-E-40 tool holders - Pallets with attached specific fixtures External reference: Demo - Lot 1

Condition: good (used), Year of construction: 2024, A pre-owned Optos California ultra-widefield retinal imaging system, acquired in 2024, is supplied in its original Optos transport packaging. The complete system was purchased in 2024. Some individual components may have manufacture or procurement dates from 2023, which is normal for a multi-component system. Configuration: FA Model: California / P200DTx Manufacturer: Optos Condition: Pre-owned – used during a short clinical study The Optos California platform is designed for ultra-widefield retinal imaging and provides up to a 200° field of view in a single capture. This FA configuration supports fluorescein angiography in addition to the retinal imaging modalities available on the California platform. Included configuration: Scan head Touchscreen tablet & stand Image server with monitor Specialized device table OptosAdvance software Color & Red-free imaging Autofluorescence Fluorescein angiography The system is currently securely packed and palletized for transport. The shipment includes the Optos system and associated device table as shown in the image. Iodpfx Agsz Dq Sts Astn Inspection is available by appointment. Worldwide shipping can be arranged.

Condition: used, Shredding Machine MGZ 1330, 37 kW Operating hours: 275 Included: - Second knife row - Fast hydraulics for increased throughput - Preparation for conveyor belt Optional: - Conveyor belt with automatic metal separator Your advantages: + Extremely large cutting chamber opening; top: 1300x1200mm + Special rotor suitable for both hardwood and softwood + Energy-efficient and powerful, 37 kW start-up power Technical data: Feed opening, top (mm): 1,300 x 1,200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Power requirement (kW): 37 Screen hole size (mm): configurable Tools: 37/70 knives Extraction connection diameter (mm): 200 mm Dimensions: 2430x2410x1735 mm (LxWxH) Weight (approx. kg): 3,500 --- Feedstock requirements: - The moisture content (atro) must be below 20% - The feed material must be free of metals and mineral contamination. Damage to the tools and/or increased wear may result. Isdpfex Tfdhex Ag Aetn

Condition: used, empty load weight: 3,790 kg, maximum load weight: 9,210 kg, overall weight: 13,000 kg, axle configuration: 2 axles, first registration: 09/2007, loading space length: 6,200 mm, loading space width: 2,450 mm, loading space height: 400 mm, loading space volume: 6 m³, total length: 6,200 mm, suspension: parabolic leaf (spring), tire size: 205/65 17,5, tire condition: 30 %, wheelbase: 1,010 mm, color: orange, Year of construction: 2007, front tire size: 205/65 17,5, rear tire size: 205/65 17,5, driver cabin: day cab, emission class: none, Equipment: ABS, truck registration, Vehicle number for inquiries: 2315 Wellmeyer, Heinrich, low-bed trailer * Year of manufacture: 2007 * ABS, Anti-lock Braking System * Air coupling, Duomatik type * Suspension: Leaf spring * Gross vehicle weight: 13,000 kg * Unladen weight: 3,790 kg * Payload: 9,210 kg * Permissible gross vehicle weight: 13,000 kg * Tire condition 1st axle: 30%|30% -- 30%|30% - Tire size: 205/65 R17.5 * Tire condition 2nd axle: 30%|40% -- 40%|30% - Tire size: 205/65 R17.5 * Wheelbase: 1010 mm * Tire sizes: 205/65 R17.5 * Internal dimensions: L = 6200 mm, W = 2450 mm, H = 400 mm * Internal volume*: 6 m³ * Pallet spaces: 15 * 40 mm drawbar eye * Hydraulic ramps * Steel floor with tie-down points * Ramp length approx. 2400 mm Disclaimer: Subject to changes, prior sale, and errors. You can find more photos and videos on our website. Our extensive service includes, for example: * Purchase/sale/rental of commercial vehicles * Fast and straightforward financing Itjdpfozwt Adjx Ag Aen * Processing of all (export) documents * Ordering export license plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. * Professional loading/load securing * TÜV inspections, registration service * Transportation of commercial vehicles Please contact our trained specialists; we will be happy to advise you.

Condition: as good as new (ex-display), Demonstration unit with 7 operating hours immediately available (ex works Neckartailfingen) Shredder MRZ 830 Commodity code: 84659600 Year of manufacture: 2023 Infeed opening 800x1000 mm Motor: 22 kW; 400 V - 50 Hz - 3 phase Blades: multiple-rotation hydraulically actuated slide Screen size selectable (10 - 40 mm) Weight approx. 1,600 kg Dimensions (l x w x h) approx. 2290 x 1420 x 1750 mm Turbo coupling Standard equipment includes: - automatic star/delta start - fast hydraulics - auto. OFF when rotor is idling - speed 70-90 rpm for high throughput - cycle control to avoid idle times - performance-enhancing step control of the hydraulic slide - Pertinax guides for hydraulic slide - vibration-dampening machine feet - CE compliant The shredder is designed for shredding natural wood, chipboard, and MDF, as well as other materials after testing and approval by the manufacturer. Included: - Shredder raised by 30 cm (preparation for conveyor belt) Additional shredder options: - Articulating conveyor belt + €8,770 net Horizontal section: 1200 mm Inclined section: 2500 mm Angle: adjustable from 0-60 degrees Iedpfx Agjv Sqrpo Ajtn Discharge height: approx. 2000 mm + - 100 mm - Overband magnet + €6,780 net - Control for conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the shredder) Requirements for the raw material: - The moisture content (as received) must be below 30%, - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear.