Used Pony Luxury Coating M&K S10 Und F10 for sale (88,231)

Condition: new, Equipment: cabin, Stationary small parts spray booth Dixi █████ Achieve perfect and uniform coating of small parts. The extraction system ensures optimal results even in the smallest spaces. Optionally equipped with a turntable or a wheel holder, as well as a compact yet powerful extraction unit, it is perfectly suited for processing small workpieces and wheels. The side panels effectively limit the distribution of overspray, allowing work to be carried out in confined spaces without contaminating surrounding areas. Integrated lighting is also available as an option. Ijdpfoxa Hx Rsx Abbstf Additionally, thanks to its low weight and minimal connections, the booth can be relocated to a new site in no time, ensuring your flexibility at all times. The system comes fully pre-assembled and ready for immediate use. Your Benefits Thanks to its compact design, flexible dimensions, and versatile accessories, this booth offers a broad range of applications. The sophisticated modular system requires minimal space and is therefore suitable for use in virtually any premises. Different filter media and stages enable highly efficient operation, while filter changes can be performed in just a few minutes. Application and Safety Processing of both water-based and solvent-based coating materials is enabled by the use of ATEX-certified explosion-proof motors. It can also optionally be used for spraying adhesives. The large filter surface ensures uniform extraction throughout the process.

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 3,500 mm, total length: 7,050 mm, total width: 4,100 mm, volume flow: 36,000 m³/h, temperature: 80 °C, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), Equipment: cabin, lighting, Paint and Drying Booth It is the centerpiece of your entire painting operation: the combined paint and drying booth. (Alternatively available as a separate paint booth with a dedicated dryer.) Our solutions feature full-surface ceiling filters and, optionally, full-surface floor extraction with drive-over grating or wall extraction at the position of your choice. Itodpfexa H Ewjx Abbof If you wish to further increase the efficiency of the system beyond heat recovery and infinitely variable control via frequency converter, we can also offer you a sectional control system. This enables you, for example when doing spot repairs or partial booth loading (such as painting only add-on parts), to activate only the section where the parts are located. This allows you to operate with a reduced air volume, save energy, and minimize costs, all without compromising quality. Feel free to contact us – we would be happy to demonstrate these options in detail. Do you have any questions or suggestions? We are happy to assist you.

Condition: new, Year of construction: 2025, total height: 4,000 mm, total length: 7,000 mm, total width: 3,000 mm, warranty duration: 24 months, temperature: 80 °C, air demand: 36,000 m³/h, input voltage: 380 V, heating capacity: 345 kW (469.07 HP), power: 40 kW (54.38 HP), fuel: liquid petroleum gas (LPG), energy consumption: 40 kWh, insulation material: Mineralwolle, insulation thickness: 50 mm, nominal power: 345 kW (469.07 HP), Equipment: lighting, MAIN STANDARD Our paint booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. Booth processes are managed via a PLC system, ensuring that desired values are maintained consistently. OPERATING PRINCIPLES OF THE BOOTH The booth’s processes are managed through a control panel, which oversees the following steps: PAINTING PROCESS During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (paint stop filters) collect paint particles, and the air passes through final exhaust filters before being discharged. FLASH-OFF PROCESS After painting, the booth continues operating for approximately 15 minutes to purge residual solvents and thinners. During this phase, fresh air circulates from outside into the booth. DRYING PROCESS In this stage, 80% of the air passing through the booth is heated to 60°C and introduced via a distribution system. Since 20% of the solvent is released during drying, it is expelled with the exhaust air. Industrial coatings are typically dried at 60°C, but the booth temperature can be adjusted as needed via the control panel. COOLING PROCESS After the 30-minute drying cycle, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the subsequent 5-minute cooling phase, fresh air from outside circulates through the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels govern the functions and operation of machines and devices housed within the booth. The panel is made of durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical Equipment and Control Panel: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to accommodate booth relocation if needed. Itjdewzmcbopfx Abbof • Operating equipment uses 380 V 50 Hz, while control devices operate at 220 V. • The booth’s operation time can be monitored on the electronic control panel, enabling straightforward maintenance scheduling. • Temperature and time settings for booth ventilation (solvent flash-off), intermediate drying, and final drying can be easily adjusted to required values on the digital display of the electronic control panel. • Users can monitor and adjust the drying time using the heating thermostat and time relay.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: PEF-2.5 PULVER EINBRENNOFEN ELEKTRISCH, temperature: 230 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, inner dimension width: 1,505 mm, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ ⭐ Powder furnace with electric heating - ✔️ Internal dimensions: 2500 mm L * 1505 mm W * 1800 mm H ✔️ Electric heating output: 30 kW/h ✔️ Fan: 3000 m3/h 80 mm SS ✔️ Circulation fan output: 1.5 kW/h Itjdpfxjwfgbrj Abbof ✔️ Total 35 kW/h +- 10% ✔️ Digital heat control, continuously adjustable temperature up to 220°C ✔️ Sandwich panels inside: 1.5 mm galvanized steel, outside: 1.5 mm powder-coated Steel ✔️ Adjustable curing temperature, curing time, and exhaust fan function ✔️ An audible signal sounds at the end of the curing time ✔️ Insulated door with special locking systems (snap lock) ✔️ Insulation: 150 mm (150 mm rock wool) 🔥 PEF-2.5 Curing Oven: Your versatile industrial oven for drying and curing processes! 🔥 Whether powder coating, wet paint, plastic processing, or other thermal processes – the powder curing oven is your reliable solution for professional curing and drying processes up to 230°C! 🌡️ _____ 🚚 Maximum loading flexibility • Compatible with ceiling rail systems • Optionally with insert shelf system for small batches _____ ⚙️ Intelligent control – just the way you need it ✅ PID control (optional) for precise temperature control ✅ Touchscreen control panel & smartphone control 📱 (optional) ✅ Weekly & monthly reports at the touch of a button (optional) ✅ Timer function: freely programmable from 10 minutes to 24 hours ⏲️ ✅ Automatic shutdown after the end of the process _____ ♨️ Ramp heating mode (optional) Precisely control temperature progression and holding times, e.g. E.g.: • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Request more information

Condition: new, Year of construction: 2024, functionality: fully functional, ⚡️ Top Service ⚡️ Fast Delivery ⚡️ Excellent Support! ✈️ Price includes shipping within Germany – No additional transport costs! ✈️ Fast delivery: Only 6 weeks after receipt of payment! PROFESSIONAL POWDER COATING HAS NEVER BEEN THIS EASY! Looking to expand your business and enter the world of professional powder coating? The PEF2.5+ is the perfect solution for beginners! This high-performance system allows efficient, cost-effective, and high-quality coating of car rims and smaller workpieces – with minimal effort! ✨UNBEATABLE PROMOTION – ONLY UNTIL THE END OF MAY!✨ Take advantage of this limited-time offer before it's too late! PONY Luxury Coating – QUALITY THAT CONVINCES! ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✅ 100% European manufacturing – No China products, only top quality built to European standards! ✅ Modular & expandable – Additional options for greater performance and flexibility! ✅ All spare parts included – Long-term use with no hidden extra costs! ✳️Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today. ✳️ ✨✨Buy directly from the manufacturer and secure price and quality advantages!✨✨ ☘️Environmentally friendly☘️⚡️Green Energy⚡️☘️ Powder oven + powder booth + powder gun Ijdpfx Abowfhu Hjbstf Complete Starter Package PEF2.5+ ⭐ Powder oven with electric heating ✔️ INTERNAL WIDTH: 1,505mm ✔️ HEIGHT: 1,800mm (from air duct) ✔️ INTERNAL LENGTH: 2,500mm ✔️ Thermoblock unit dimensions: 785x1800x2210mm; heating capacity is 30 kW/h; recirculation fan is 1.5kW/h – 1 pc.; exhaust fan is 0.54kW/h. ✔️ Double-wing door with thermal insulation and silicone seal. ✔️ Guide rails for rack trolleys are manufactured according to the dimensions specified on the base plates. ✔️ Specially designed air duct for homogeneous air distribution inside the curing oven. ✔️ Electrical panel materials by Siemens and Schneider. This curing oven does not include a PLC system. PLC is available as an option. ✔️ Curing temperature, curing time, and heater unit function are adjustable. At the end of the program, an alarm and light signal from the buzzer will indicate completion. ✔️ Additionally, a product transport trolley with cast wheels is located inside the oven. ⭐ Powder coating booth ✔️ Dimensions: 800x1930x2200mm (including fan) ✔️ Teflon filters: 4 pcs. ➢ Filter suction fan: 4kW x 1 pc. (6,000m3/h – 200mmSS) ✔️ 36W LED lighting x 1 pc. ✔️ Bottom drawer x 1 pc. ✔️ Control panel for air intake and powder spray regulation ✔️ DELTA frequency converter ✔️ Heavy-duty rollers under the coating booth ✔️ Additional filter at the fan outlet ⭐ Powder coating gun E-Coat+3 Master with Multicolor (vibration table) Enquire now – Get your business ready for the future! ☀️ 2-YEAR WARRANTY ☀️ ☀️All our machines are CE-certified and necessary machines have ATEX certificates.☀️

Condition: new, Year of construction: 2025, total height: 982 mm, total length: 4,000 mm, total width: 1,100 mm, volume flow: 18,000 m³/h, warranty duration: 12 months, Extraction wall with 18,000 m3/h Iedpfxowz Ic Nj Abbjtf Max. power consumption 5 kW/h Electric motor 4 kW Air unit 18,000 m3/h Nicotra ADH 400 The full description can be found in the attachment to this listing.

Condition: new, Powder Coating Systems Itsdpfxoxa Hzxo Abbjf For years, powder coating has been continuously evolving as an alternative to wet painting, and it has recently gained increasing importance due to its lower environmental impact—specifically the absence of solvents and paint sludge. Powder recovery further boosts the efficiency of these systems to a particularly high level. For users, powder coating offers the advantage of creating an extremely durable and corrosion-resistant surface that is significantly more impact-resistant than what traditional painting can achieve. Additionally, post-processing tasks such as grinding or drilling the powder-coated parts present no problems, as the coating will not chip off. Pony Luxury Coating powder coating systems provide you with tangible advantages: they are efficient, environmentally friendly, and—as always—unsurpassed in flexibility. We achieve this through a range of system types. Manual Powder Coating Systems Manual coating systems are the ideal solution for complex and demanding workpieces. Thanks to skilled operators, these systems offer continuous adaptation to changing conditions and varying product sizes. Flexibility is paramount—with the added benefit of an attractive entry price into the world of powder coating. Large-Scale Powder Spray Booths No matter how large or challenging your workpieces, our systems are larger! In the commercial vehicle and utility sector, where components are exposed to significant stress, powder coating has established itself as the ideal solution. To accommodate ever-larger components, we offer our large-scale powder booth, which supports unlimited manual coating, and, when combined with a conveyor system, handles any workpiece size with ease. Automatic Powder Coating Systems If your operation requires high throughput and rapid processing, an automated powder system is the way forward. Coupled with a conveyor, light barriers allow precise detection and, consequently, exact powder dosage to ensure maximum efficiency. The system can also be equipped with lifting stations and robots to handle even the most complex components. Powder Curing Ovens & Flash-Off Dryers These provide the perfect finishing touch to powder coating: the curing oven. Our ovens feature the highest insulation class, ensuring consistent, high efficiency. Detailed temperature control also enables use as a flash-off dryer to dry substrates after pre-treatment. Temperatures up to 250 degrees Celsius are possible, which allows usage as a tempering oven, for instance with hot-dip galvanized materials. Of course, typical use as a powder curing oven is straightforward. Optimal air distribution and a visualized control panel prevent over-baking, and even allow multiple color shades to be cured in a single process. Do you have questions or suggestions? We are happy to assist you!

Condition: new, Year of construction: 2024, functionality: fully functional, total length: 3,400 mm, total height: 2,210 mm, total width: 1,505 mm, type of input current: three-phase, warranty duration: 24 months, temperature: 250 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, Equipment: emergency stop, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! Itjdpfxjwdtfus Abbjf ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ PEF-2.5 ELECTRIC POWDER FIRING OVEN WIDTH (INTERIOR): 1,505 mm HEIGHT: 1,800 mm (from the air duct) LENGTH (INTERIOR): 2,500 mm ➢ The thermoblock unit measures 785 x 1,800 x 2,210 mm. The heating capacity is 30 kW/h. A circulating fan is 1.5 kW/h (1 pc.), and an exhaust fan is 0.54 kW/h. ➢ Double-leaf door with thermal insulation and silicone seal. ➢ Guide rails are manufactured for trolleys in the dimensions indicated on the floor panels. ➢ Specially designed air duct ensures uniform air distribution in the curing oven. ➢ The electrical switchgear is made of Siemens and Schineider. This curing oven does not have a PLC system. PLC is available as an option. ➢ Curing temperature, curing time, and heating unit function are adjustable. At the end of the program, an audible and light signal is emitted by the buzzer. ➢ Additionally, a product transport cart with cast wheels is located inside the oven. 2. PKF-4 POWDER COATING BOOTH ➢ DIMENSIONS: 800x1930x2200mm (dimensions including fan) ➢ Teflon filters: 4 pcs. ➢ Filter suction fans: 4 kW x 1 pc. (6,000 m3/h – 200 mm SS) ➢ 36 W LED lighting x 1 pc. ➢ Bottom drawer x 1 pc. ➢ Control panel for controlling air intake and pressure blasting ➢ DELTA frequency converter ➢ Heavy-duty rollers under the paint booth. ➢ An additional filter is located at the fan outlet. ♨️ Ramp heating mode (optional) Precisely control temperature progression and dwell times, e.g. E.g.: • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Request more information

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. Iedpfx Ajwzl Hxsbbotf * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: reconditioned (used), stock-No. 2452 1 used, partly overhauled and functionally tested pelletizing line capacity up to 300 kg/h depending material, equipped with: Kreyenborg Force-feeder SW 100, motor 7,5 kW Extruder BKG single-screw Ø 100 mm – 35 LD, motor 132 kW – AC Screw speed up 143 r.p.m. screw depth 14 mm heating power installed 35 kW 1x athm. venting port with „Stuffer“ * Kreyenborg K-SWE 160 RS screen-pack-changer back-flush self-cleaning with filter surface 244 cm² BKG underwater pelletizing unit AH 300, complete with : diverter-valve , hydraulic unit pelletizer, motor 4 kW incl. die-plate and knife-holder Water pump 2,2 kW By-Pass System, Process water tank heating power 9 kW Heat-exchanger BKG pellet spin-dryer TWE 300 with motor 3 kW control-board and operation panel OPTIONAL against additional price ᐳ * Vacuum pump ᐳ pellet classifier sieve, conveying, Big-Bag Station ᐳ chiller – cooling unit Ijdpfx Ajh Eyd Rsbbjtf More pelletizing lines ex workhop Wuppertal-Germany available, ask for our most recent machine-stock-list or visit us, you´re welcome.

Condition: reconditioned (used), stock-No. 2452 1 used, partly overhauled and functionally tested pelletizing line capacity up to 300 kg/h depending material, equipped with: Kreyenborg Force-feeder SW 100, motor 7,5 kW Extruder BKG single-screw Ø 100 mm – 35 LD, motor 132 kW – AC Screw speed up 143 r.p.m. screw depth 14 mm heating power installed 35 kW 1x athm. venting port with „Stuffer“ * Kreyenborg K-SWE 160 RS screen-pack-changer back-flush self-cleaning with filter surface 244 cm² BKG underwater pelletizing unit AH 300, complete with : diverter-valve , hydraulic unit pelletizer, motor 4 kW incl. die-plate and knife-holder Water pump 2,2 kW By-Pass System, Process water tank heating power 9 kW Heat-exchanger BKG pellet spin-dryer TWE 300 with motor 3 kW control-board and operation panel OPTIONAL against additional price Itjdpoi Dtb Ujfx Abbof ᐳ * Vacuum pump ᐳ pellet classifier sieve, conveying, Big-Bag Station ᐳ chiller – cooling unit More pelletizing lines ex workhop Wuppertal-Germany available, ask for our most recent machine-stock-list or visit us, you´re welcome.

Condition: reconditioned (used), stock-No. 2452 1 used, partly overhauled and functionally tested pelletizing line capacity up to 500 kg/h depending material, equipped with: Kreyenborg Force-feeder SW 100, motor 7,5 kW Extruder BKG single-screw Ø 100 mm – 35 LD, motor 132 kW – AC Screw speed up 143 r.p.m. screw depth 14 mm heating power installed 35 kW 1x athm. venting port ( vacuum-pump optional ) Kreyenborg K-SWE 160 RS screen-pack-changer back-flush self-cleaning with filter surface 244 cm² BKG underwater pelletizing unit AH 300, complete with : diverter-valve , hydraulic unit pelletizer, motor 4 kW incl. die-plate and knife-holder Water pump 2,2 kW Itjdped Sg I Iofx Abbjf By-Pass System, Process water tank heating power 9 kW Heat-exchanger BKG pellet spin-dryer TWE 300 with motor 3 kW pellet classifier sieve control-board and Siemens Touch operation panel (updated ) OPTIONAL against additional price ᐳ * Vacuum pump ᐳ ,material feed conveying, Big-Bag filling Station ᐳ chiller – cooling unit More pelletizing lines ex workhop Wuppertal-Germany available, ask for our most recent machine-stock-list or visit us, you´re welcome.

Year of construction: 2026, condition: new, Offered is an attachment block broom Kehrfix in different versions from 1.50 m to 4.00 m width. A pick-up must then still be discussed separately if this is desired (e.g. pallet fork pick-up, shovel hook or Euro pick-up). An attachment block broom for forklifts, wheel loaders, tractors, mini-loaders, mini-dumpers and many other vehicles and equipment! With various attachments for quick mounting on a variety of vehicles, the KehrFix is the perfect aid for keeping larger areas clean. Itodpfeh T A Tnox Abbof The KehrFix push brooms are a professional choice for easy and effective sweeping and cleaning. The rugged KehrFix is designed to get the job done quickly and thoroughly in every conceivable application. KehrFix push brooms are high-quality, durable, maintenance-free and universally applicable sweeping systems.

Condition: used, mileage: 177,395 km, power: 315 kW (428.28 HP), first registration: 10/1999, overall weight: 35,000 kg, fuel type: diesel, color: yellow, axle configuration: 8x4, maximum load weight: 14,855 kg, empty load weight: 20,145 kg, wheelbase: 4,500 mm, brakes: constant throttle, driver cabin: day cab, gearing type: mechanical, emission class: euro2, suspension: steel, number of seats: 2, Equipment: ABS, additional headlights, air conditioning, cabin, cruise control, differential lock, immobilizer system, low noise, parking heater, power assisted steering, seat heater, Vehicle location: Bovenden, Mtlg. house, 1x comfort seat, seat heating, rear window, electric mirror, heated mirror, electric window left, electric window right, air conditioning, sun visor, cruise control, auxiliary heating, air horn, switch 16, ABS (anti-lock braking system), traction control system (ASR), constant throttle, power take-off, raised exhaust, differential lock, fog lights, driving lights, work lights, rotating beacon, storage box, leaf suspension, low-noise G1, winter service equipment, 2-axle forward steering, U-protection, rear outlet, roof hatch, red environmental badge Wheelbase: 4500 mm Body: Suction and flushing vehicle Müller type Canalmaster F170K approx. 17m³ (10,000l sludge chamber/2x 3.500l water tank) 7.5t front axle, rear axle H7 13t crown wheel 300, EPS gearbox 16-speed, drum brakes on front and rear axle, parameterizable special module (PSM), additional thermal insulation, additional hot air heating, flame system, automatic daytime running lights, transmission oil cooling, comfort package, auxiliary drive countershaft MB 2c, auxiliary drive independent of transmission (NMV) i=1.09. -Müller Canalmaster F 170 K -High pressure pump Uraca KD 716 G/60 170bar/325l/min -SL2100 vacuum pump -Bosch HY/ZFFS 15/19+8 oil pump -Eberspächer V7S heater -Mud chamber approx. 10.000l -2x set water tanks approx. 3,500l -Swivel suction hose holder DN 100 The body and the reel are encased for winter operation! ACCESSORY INFORMATION WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! Itsdpfx Asvhi Ubsbbef - .

Condition: ready for operation (used), Leukhardt LS-IC / ISA-K ID 6307080 industrial computer with screen and keyboard 482 x 310 x 410 mm, serial number as per photo, used, minor signs of wear, 100% functional, scope of delivery as per photos Iodpfxoi Ebyce Abbstf

Condition: ready for operation (used), Leukhardt LS-IC / ISA-K ID 6307080 industrial computer with screen and keyboard 482 x 310 x 410 mm, serial number as per photo, used, minor signs of wear, 100% functional, scope of delivery as per photos Itodpfx Absi Ebx Ujbsf

Condition: used, Year of construction: 2005, container length: 24 ft, overall weight: 16,000 kg, empty load weight: 3,250 kg, loading space width: 2,480 mm, loading space length: 7,300 mm, loading space height: 2,720 mm, machine/vehicle number: 610272 8, JUMBO BDF swap body swap body with roller shutter * beaded steel box body * Crane and stackable * Length 7.45 m * Roller shutter door * Interior keyhole panel * Screen printed floor * neutral white WITHOUT labeling! Itsdpfoi Avlljx Abbjf * Guide tunnel at the front slightly deformed * Slight rust on frame and body * Parking height: 1.02 - 1.32 m * Loading height at the roller shutter: 2,620 mm * External height: 3,000 mm * UVV inspection on request new * Manufacturer: KRONE Delivery possible nationwide! We always have larger quantities of different manufacturers and designs for sale or for RENT in stock !!! All prices net plus VAT!

Condition: used, functionality: fully functional, Year of construction: 2005, color: red, overall weight: 16,000 kg, maximum load weight: 13,000 kg, empty load weight: 3,000 kg, loading space width: 2,480 mm, loading space length: 7,300 mm, loading space height: 2,460 mm, machine/vehicle number: 04851, BDF Steel Swap Body / Swap Container 7.45 m with Roller Shutter * Swap container / steel box with profiled external walls * Craneable and stackable * Aluminum roller shutter – fully refurbished * Keyhole rails * Laminated plywood floor, suitable for forklift traffic * Forklift pockets and upper corner fittings * Support legs not height-adjustable * Parking height: 1.32 m * Internal loading height at roller shutter: 2.20 m * Technically in very good condition Rental from just 1 day, long-term rental possible! Ijdpfx Aswtqt Iobbstf We always have larger quantities from various manufacturers and in different versions available for sale or rental! Delivery possible throughout Germany!

Condition: excellent (used), For sale: Industrial pump from the renowned manufacturer Grundfos. Model SPK 4-8 – vertical multistage pump designed for clean liquids, coolants, industrial installations, and CNC machines. Technical data: Manufacturer: Grundfos Model: SPK 4-8 A-A-A Power: 0.55 kW Iedjywpahjpfx Abbjtf Speed: 2850 rpm Capacity: approx. 3 m³/h Head: up to 28 m Liquid temperature: max 90°C Country of manufacture: Denmark Condition: Used, fully functional. Visible signs of use (abrasions, minor corrosion – see photos). A crack is visible near the nozzle on the casing – does not affect operation (buyer to verify).

Condition: excellent (used), Year of construction: 2018, DEKUMED Unidos U300 TXMP LC 2K Metering and Mixing System – Year of Manufacture 2018 – Fully Refurbished in 2021 For sale is an industrial 2-component metering and mixing unit from DEKUMED, model Unidos U300 TXMP LC, year 2018. The system underwent a comprehensive overhaul at the end of 2021 (investment approx. €18,000) and has been in like-new condition since. Following the refurbishment, the machine was no longer put into operation and has been professionally stored. This system is designed for the precise conveying, dosing, and mixing of 2-component materials (e.g., resin/hardener systems), making it ideal for applications in: Iedpfx Asy Dpvijbbstf - Plastics processing - Adhesive technology - Potting and coating processes - Industrial series production The unit features two separate drum follower units for components A and B, as well as a central mixing head. Control is via a Siemens LOGO! TDE operator panel, allowing for easy, precise, and reproducible process management. Technical specifications: - Supply voltage: 3 x 400 V - Frequency: 50 Hz - Fusing: 3 x 16 A - Max. current draw: approx. 9 A - Maximum discharge output: approx. 5,000 g/min (5 kg/min) - Mixing ratio: 100 : 42 - Compressed air supply: 6–10 bar (oil-free) - Compressed air consumption: approx. 400 l/min - Weight: approx. 700 kg - Dimensions (L x W x H): approx. 2340 x 1170 x 1920 mm - Operating temperature: +20 to +40 °C Equipment: - 2K dosing and mixing system - Drum follower units for components A and B - Mixing head with connections - Siemens LOGO! control system with TDE operator panel - Operating elements (start/stop, flushing, discharge output) - Mobile platform - Complete documentation, including operating manual and data media Condition: - Fully refurbished at end of 2021 - Unused and stored since - Technically as new - Cosmetic condition: see photos Scope of delivery: - DEKUMED Unidos U300 TXMP LC unit - Control unit with operator panel - Documentation (binder + CD) - Accessories as shown in photos Additional information: - Inspection possible by appointment - Loading / shipping by freight forwarder possible - Subject to prior sale and errors

Year of construction: 2025, condition: new, functionality: fully functional, We are offering this new LOWA GmbH Filling and Capping Systems capping machine, model WK12-17, bottle filling and capping machine, year of manufacture 2025. Manufacturer: LOWA GmbH Filling and Capping Systems Model: Capping Machine WK12-17 Machine type: Bottle Filling and Capping Machine Isdpfx Abeyybh Aobotf Year of manufacture: 2025 Condition: new Category ID: 679 If you have any questions or need more information, feel free to send us a message or call us.

Condition: like new (used), Year of construction: 1993, functionality: fully functional, Dowel and slot mortising machine GANNOMAT JUNIOR 320 LBM Very good condition, like new; the machine comes from a very small joinery and was used only very little. The machine is in its original state and has only been cleaned, with no touch-ups to the paint. You can mill slots and drill dowel holes on two levels without having to reclamp the workpiece. 380V, 1500W Speed: 2800 rpm Year of manufacture: 1993 With this machine, you can mill slots, for example for lock cases and similar applications, or make all types of frame dowel joints, at right angles, butt joints, or mitred joints. Ideal for producing dowel joints in timber frame construction, furniture, door, window, and staircase manufacturing, as well as similar applications. Itsdjynv E Ropfx Abbof By drilling on two levels, using the stops and indexing rails, and due to the machine’s design, dowel joints can be produced in a very short time, which makes the machine highly efficient. The machine requires a compressed air connection of 6 bar (air consumption is very low). Right-hand rotation. Mills and drills very efficiently and cleanly. Supplied with 2 angle stops (one center stop and one side stop, which can be used on either side), plus a mitre stop. On the front of the machine table, there is a 2000mm long stop rail with 2 flip stops; the stop rail can be shortened or extended if required. Workpiece clamping is done with 2 pneumatic clamping cylinders. Height adjustment between drilling levels is also pneumatic; the pneumatic switch is located at the front of the machine, ensuring rapid adjustment of the index positions and drilling levels. Equipped with a precision 12mm indexing rail, featuring a center index and 12 indices left and right. Can be quickly converted for slot milling; in this mode, the machine can be used without indexing, with 2 adjustable stops left and right, allowing for a maximum working width of 420mm. Maximum drilling hole height: 100mm Maximum drilling depth: 150mm with stop and scale Maximum workpiece height: 160mm Everything functions perfectly. The machine is personally delivered and demonstrated by us anywhere in Germany for €220.00, so you have no risk when purchasing. Delivery to Austria and the EU is also possible on request. The machine table is 870mm wide, 140mm deep at the sides, and 350mm deep in the center. Professional equipment, not DIY store scrap. Ready for immediate operation. With 2-jaw drill chucks up to 20mm. Very stable and durable construction. The precision guides with play-free ball bearing bushings are in excellent condition and move smoothly.

Condition: good (used), Year of construction: 2006, machine/vehicle number: Serien Nr. 64019447, Used Coperion Werner and Pfleiderer ZSK 34 Mvc twin-screw extruder for sale. The extruder was used for powder coatings Ijdpfx Abjvcyk Nsbotf

Condition: good (used), Technical data for the pallet rack beam: Racking system: SSI Schäfer Type: PR 600 Included in the scope of delivery: 01x pallet rack beam, used Material color: yellow Box profile: 60 x 40 mm Beam type: TRV1-270-064-30 CE Clear span: 2,700 mm Bracket: 5 HK (hooks) 02x safety pins, used Design: fully galvanized For securing the cross beams against accidental lifting Your contacts at our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is only offered for collection. If transport or shipping is desired, additional costs will apply. These can be requested from us separately depending on the delivery location and scope of delivery. Isdpfoynlrajx Abbjtf

Condition: new, Year of construction: 2025, functionality: fully functional, power: 5.5 kW (7.48 HP), cutting height (max.): 200 mm, saw blade diameter: 520 mm, rotational speed (min.): 2,800 rpm, cutting length (max.): 420 mm, workpiece height (max.): 200 mm, feed length X-axis: 420 mm, length stop: 8,800 mm, pressure: 5 bar, space requirement length: 8,800 mm, space requirement width: 1,200 mm, Equipment: double-sided, Mobile saw base frame; total length approx. 8600 mm for Graule ZS 200 saw; stop roller conveyor on the left side 5200 mm, measuring length from 400 - 5960 mm, with digital LED measurement display, measuring length including extension approx. 8800 mm, Itjdpfjv Hhg Tsx Abbef Saw base frame with 6 crank supports ensure safe standing when working. With electrical power distribution and 3-way socket 230 V Mobile saw base frame Beck ESF 1, saw ZS 200 mounted on base frame