Used Weingarten Nr 80 for sale (19,228)

Year of construction: 1978, condition: used, pressure 80 t throat 280 mm stroke 8-112 mm no. of strokes 55 / 82 Hub/min ram - range of adjustment 80 mm table surface area 800x570 mm ram surface 560x355 mm hole in the table Ø 280 mm table height 800 mm Nedpfelp U Ddox Aa Rslf tool hole in ram Ø 50 mm total power requirement 7,5 kW weight of the machine ca. 6 t dimensions of the machine ca. BxTxH 1600x2200x3000 mm

Condition: used, Year of construction: 1977, pressure 080 t throat 280 mm stroke 8 - 112 mm no. of strokes 30 - 120 /min distance table/ram, max. stroke up, adjustment up 500 mm table surface area 840 x 580 mm hole in the table 150 mm table height over floor 910 mm passage to the back 640 mm ram surface 560 x 300 mm ram adjustment 80 mm Nodpfszrpppex Aa Rolf power requirement 7,5 kW weight 8,0 t dimensions (WxDxH) 1,6 x 2,3 x 3,3 m with infinitely variable drive, pneumatic clutch, hydraulic overload protection in ram, motoric ram adjustment, inclineable, two-hand operation

Condition: used, Year of construction: 1977, pressure 80 t stroke 8 - 112 mm Nsdszrpqmspfx Aa Rolf no. of strokes 65 /min throat 345 mm passage to the back 500 mm dayligth 472 mm table surface area 840 x 610 mm hole in the table 280 / 315 mm table height over floor 800 mm ram surface 650 x 410 mm ram adjustment 71 mm power requirement 13,5 kW Weight 6,10 t dimensions of the machine ca. 1,5 x 1,9 x 3,0 m x m x m with motor with two speeds, pneumatic clutch/brake combination (Ortlinghaus), mechanical overload protection in ram, manual stroke adjustment, motoric ram adjustment, fix table, motoric centralized lubrication, two-hand operation

Condition: used, Year of construction: 1996, pressure 80 t throat 320 mm stroke 6 - 118 mm no. of strokes 30 - 80 Hub/min Nljdpfstycdkjx Aa Ref ram adjustment 70 mm table surface area 830 x 610 mm ram surface 650 x 400 mm column daylight (nach hinten) 630 mm total power requirement kW weight of the machine ca. 8,1 t dimensions of the machine ca. B 1,2 x T 1,9 x H 3,3 m Furnishing: - with gear transmission - fixed table - automatic stroke adjustment - automatic ram adjustment - hydr. Overload - Ejector - Grease central lubrication - Cover plate for drainage hole - Continuous speed control using a frequency converter - Machine is technically checked in our company and receives a new control cabinet with safety controls and touchscreen - current UVV test with braking time measurement

Condition: used, Technical details: plate width: 800 mm coil weight: 12 t sheet width - max.: 800 mm sheet width - min.: 300 mm thickness of strip/band: max. 5,0 mm band speed: 4,5 / 25 m/min work height max.: 1700 mm Payload: 12,0 to (Coil) Weight approx.: 7,3 + 6,62 t dimensions of coil: 3,2 x 1,9 x 2,7 m dimension machine xH: 2,5 x 2,6 x 2,45 m Decoiler with loading device Can optionally be sold together with stock no. 0100571. straightening unit: Infeed rollers: 2 x Ø 144 x 850mm Straightening rolls: 3 x bottom rolls, rigid, Ø 100 x 850mm, 30mm adjustable 3 x top rollers, Ø 110 x 850mm; 30 mm adjustable Coil unwinding machine: Outer Ø 1.500mm Strip width max. 800mm Load capacity max. 12 to Clamping Ø 470 - 630 / 570 - 730mm Transport unit LxWxH: 1700 x 1500 x 1000mm; crosswise running, with prism support 1000 x1000mm Machine will be offered and sold with Stock no. 0100521 as a decoiling and streightening line. Nledpfx Aou Ic Avea Rsf *

Condition: used, Technical details: plate width: 1000 mm plate thickness: 3,0 mm smallest sheet thickness: 0,5 mm distance between columns: 920 mm Number of Straightening rolls: oben 4x unten 4x Stück / pieces roll diameter: ca. 75 mm number of rollers: 2 oben und 2 unten St. weight of the machine ca.: 6,5 t dimensions L x W x H: 3,8 x 2,2 x 2,1 m This is a sheet metal straightening machine with hydraulic feed. Further features: 4 straightening top rolls Ø 75 x 830 mm, stroke 20 mm, hydraulic 4 straightening bottom rolls Ø 75 x 830 mm, fixed, hydraulic 4 pull-out rollers Ø 110 x 480 mm, 2x top adjustable approx. 20 mm and 2x bottom, hydraulic Roller support Nljdjvgbgaopfx Aa Rsf Infeed height 1400 mm Hydraulic system equipment Operated externally Recommendation: complete conveyor system (decoiler + loading device + straightener with hydraulic feed) for sale with optional stock no. 0100572. *

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: H2X396J01484, Year of construction: 2018, operating hours: 18,822 h, load capacity: 8,000 kg, lifting height: 4,850 mm, fuel type: gas, mast type: simplex, construction height: 3,780 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Nsdpfx Aajzu Nfve Rslf Load capacity: 8,000 kg Lifting height: 4,850 mm ISO class: 4 MACHINE DETAILS Mast type: Simplex Drive type: Internal combustion engine Overall height: 3,780 mm Weight: 14,390 kg EQUIPMENT Linde Safety Pilot camera 3rd hydraulic valve 4th hydraulic valve Heater Full cabin Air conditioning

Condition: used, pressure 80 t throat 320 mm stroke 8 - 112 mm table surface area 830 x 600 mm no. of strokes 30 - 85 Hub/min ram surface 650 x 400 mm ram adjustment 71 mm Nljdjtqm Dmjpfx Aa Rof clamping plate 990 x 550 mm table height over floor 810 mm table height over floor 800 mm column daylight (vorn) 680 mm column daylight (hinten) 520 mm total power requirement 7,5 kW weight of the machine ca. 7,7 t dimensions of the machine ca. 1,5 x 2,2 x 3,15 m Equipment: - with wheel presentation - fixed table Machine was/is partially overhauled: - Complete disassembly and inspection - Table and ram surfaces milled - New seals and hydraulic hoses - new main engine - the two main bearing bushes, the bushing of the 3rd bearing and the connecting rod bushing are new - Shaft machined and booked out - Painting - new control cabinet with PLC and touchscreen including cabling. - Current UVV test with braking time measurement

Condition: like new (used), Year of construction: 2014, load capacity: 7 kg, arm reach: 800 mm, ROBOT ARM MANUFACTURER: KUKA MACHINE TYPE: LBR iiwa 7 R800 MODEL YEAR: 2014 TECHNICAL SPECIFICATIONS PAYLOAD CAPACITY: 7 KG MAXIMUM LENGTH: 800 MM Njdpfjzvyriox Aa Rolf CONTROL UNIT: KRC4 SUNRISE

Condition: good (used), pressing force: 80 t, throat depth: 400 mm, ram adjustment: 80 mm, Capacity: 80 Ton Table surface: 750 x 550 mm Ram Adjustment: 80 mm Stroke length: 8 -112 mm No. of strokes: 78 p/min. Throat: 400 mm Complete with: - Pneumatic clutch - Safety screen Nodeugtkxepfx Aa Rolf Country of origin: Germany Machine LxWxH: 2000 x 1200 x 2900 mm Machine weight: 7000 kg

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, KUKA KR 240 L180-2 2000 Robot, serial number 913766, industrial robot including control cabinet 52330. The KUKA KR 240 L180-2 robot is a {axis}-axis robot arm with a payload of 180 kg and a reach of 3100 mm. Manufacturing applications include remote TCP. Common applications for the KUKA KR 240 L180-2 include: additive manufacturing, assembly, dispensing, polishing, material handling, palletizing, and remote TCP. Specifications: Nledpfozlz Tmjx Aa Rjf Manufacturer: KUKA Model: KR 240 L180-2 2000 Type: Robot arm Axes: 6 Payload: 180 kg Reach: 3100 mm Repeatability: 0.12 mm Weight: 1277 kg Serial number: 913766 Control cabinet: 52330 Year of manufacture: 10/2008 Used – normal signs of wear. Further details, article numbers, and images available upon request. Two-week start-up guarantee. No further warranty. Spare parts are constantly available in stock. The robot is fully functional and can be inspected. Ex works / free loading. The stated amount is net. The legally required VAT of 19% will be added at checkout. You will receive a proper invoice with VAT shown. Collection on site in 74722 Buchen/Hainstadt. Shipping or forwarding costs vary depending on the quantity, weight, and desired delivery conditions. Shipping costs to foreign countries upon request – please specify country, city, and postal code. Forwarding costs upon request – please specify delivery address.

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, KUKA KR 240 L180-2 2000 robot, serial number 913762, industrial robot including control cabinet 64689. The KUKA KR 240 L180-2 robot is a 6-axis robot arm with a payload of 180 kg and a reach of 3100 mm. Manufacturing applications include remote TCP. Common applications for the KUKA KR 240 L180-2 include: additive manufacturing, assembly, dispensing, polishing, material handling, palletizing, and remote TCP. Specifications Manufacturer: KUKA Model: KR 240 L180-2 2000 Type: Robot arm Axes: 6 Payload: 180 kg Reach: 3100 mm Repeatability: 0.12 mm Weight: 1277 kg Serial number: 913762 Control cabinet: 64689 Nsdpfszmtfqjx Aa Relf Year of manufacture: 10/2008 Used – shows normal signs of wear. Further details, article numbers, and images available upon request. Two-week start-up guarantee. No further warranty. In addition, spare parts are constantly available in stock. The robot is fully functional and can be inspected on request. Free loading / ex-works. The stated amount is net. The legally required VAT of 19% will be added at checkout. You will receive a proper invoice with VAT shown. Collection on site in 74722 Buchen/Hainstadt. Shipping or freight costs vary depending on quantity, weight, and desired delivery conditions. Shipping costs to foreign countries available upon request – please provide country, city, and postal code. Freight costs available upon request – please provide delivery address.

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, KUKA KR 240 L180-2 2000 Robot, serial number 913761, industrial robot including control cabinet 52330. The KUKA KR 240 L180-2 robot is a 6-axis robot arm with a payload of 180 kg and a reach of 3100 mm. Manufacturing applications include remote TCP. Common applications for the KUKA KR 240 L180-2 include: additive manufacturing, assembly, dispensing, deburring, material handling, palletizing, and remote TCP. Specifications Manufacturer: KUKA Model: KR 240 L180-2 2000 Type: Robot arm Axes: 6 Nodpfxozmtb Sj Aa Relf Payload: 180 kg Reach: 3100 mm Repeatability: 0.12 mm Weight: 1277 kg Serial number: 913761 Control cabinet: 52330 Year of manufacture: 10/2008 Used item – normal signs of wear. Further details, article numbers and images available upon request. Two-week start-up guarantee. No further warranty. Spare parts are also continuously available in stock. The robot is fully functional and can be inspected at any time. Free loading / ex works. The stated amount is net. The legally required VAT of 19% will be added at checkout. You will receive a proper invoice with VAT shown. Collection on site in 74722 Buchen/Hainstadt. Shipping costs vary depending on quantity, weight and desired delivery conditions. Shipping costs to foreign countries on request – please specify country, city and postal code. Freight costs on request – please provide the delivery address.

Condition: excellent (used), Year of construction: 2006, operating hours: 33,107 h, functionality: fully functional, clamping force: 1,300 kN, screw diameter: 25 mm, displacement volume: 79 cm³, injection pressure: 2,398 bar, ejector force: 6,100 N, ejector stroke: 100 mm, opening stroke: 606 mm, plate length: 750 mm, plate width: 850 mm, overall weight: 10,600 kg, Equipment: documentation/manual, ENGEL V 330H/80V/130 Combi Cleanroom – 2-component injection molding machine, manufactured in 2006. The machine comes from pharmaceutical production and is designed for cleanroom applications. Technical data: Njdpfxet A Ui Ao Aa Rslf • 33,107 operating hours • Screw diameter 25/22 mm • Machine weight 10,600 kg Available additional equipment: • GEKU SR 500 ST robot • Safety cage • Rotary table • Conveyor belt Location: Schwaigern, Germany. Further technical documentation and an inspection can be arranged.

Condition: good (used), Year of construction: 1988, machine/vehicle number: 222 056 A110, Müller Weingarten CE 40.25.4 Press -WAG 850 The machine is tested according to VDE until 23.09.2026. Nlodpfx Aajqrqz Aj Ref Manufacturer: Müller Weingarten Operating voltage: 380 V Control voltage: 220 V Direct voltage: 24 V Rated current of the machine: 25 A Per/s: 50 Delivered: 1988 Overtravel: 9 mm Overtravel time: 80 ms Safety distance: 128 mm

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Nsdeu Rwa Iopfx Aa Rslf Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: used, Technical details: floor-plate length: 2003 mm plate width: 1005 mm plate height: 180 mm transport dimensions LxWxH: 2,02 x 1,05 x0,18 m Nlsdpewnfu Nefx Aa Rsf 3 pcs availabe (price per piece) Cast steel Table surface 2020mm x 995 mm Longitudinal groove: Number 4 Size: a=38, h=60, b=59, c=24 mm Center-to-center distance 250 mm Fixing hole: Number 4 Size D=30mm *

Condition: used, Single-column eccentric press WEINGARTEN type E 40 Machine. No. 643/62 Year of construction 1963 Pressure capacity 40 ton. throat depth 250 mm Table opening 150 x 80 and Ø 200 mm Table surface 560 x 460 mm ram surface 250 x 200 mm Plunger stroke adjustable 8-88 mm Plunger adjustment 63 mm Installation height 320 mm Clamping pin bore Ø 40 mm Stroke rate 100/130 strokes / min. Motor power 2.2 / 3 kW Nsdpfx Aaetx E Rqo Relf Mains connection 400 Volt, 50 Hz Table height above floor 840 mm - Clutch/brake combination with WEINGARTEN friction threaded clutch with TDC run-through protection - Electric lift release via two-hand control - Overload protection by breaker plate - Manual central grease lubrication - Front crankshaft support bearing - Control cabinet adjacent - UVV for manual insertion work Space requirement L x W x H 1800 x 1500 x 2200 mm Weight 3.1 tons

Condition: like new (used), Year of construction: 2008, operating hours: 61,300 h, functionality: fully functional, clamping force: 1,200 kN, screw diameter: 35 mm, clearance between the columns: 470 mm, pressure: 2,429 bar, Here we are offering the following well-maintained used injection moulding machine as part of our injection moulding machinery trading business. Of course, we are also actively purchasing well-maintained injection moulding machines from model year 2010 onward. We have been a wholesale dealer of injection moulding machines for over 25 years. ++++From Pharmaceutical Cleanroom Production++++ Manufacturer: KraussMaffei Machine type: KM 120-380 EX International size designation: 380 EX / 120 Machine no.: 61011287 Year of manufacture: 2008 Machine hours: 61,300 h Control system: MC5 Technical data - Clamping unit Clamping force: 1,200 kN Tie bar spacing H x V: 470 x 470 mm Platen size H x V: 780 x 735 mm Nodpfjy D Adtsx Aa Rjlf Min. mould height: 200 mm Max. mould height: 450 mm Max. platen distance: 850 mm Opening stroke: 400 mm Ejector stroke: 150 mm Ejector force: 22 kN Centric ring for moving platen D: 160 mm Centric ring for fixed platen D: 125 mm Mould weight: 1,485 kg Technical data - Injection unit Screw diameter: 35 mm Stroke volume: 156 ccm Injection pressure: 2,429 bar Screw length: 23 l/d Screw speed: 289 rpm Plasticising rate: 27 g/s PS Free shot weight: 477 g/s PS Number of heating zones: 5 Dimensions & Weight Machine dimensions LxWxH: 6 m x 1.7 m x 2.19 m Total weight: 9,700 kg Equipment Display language German Display language English +++Extras++++ Automation: Handling unit / extraction robot included – Handling: LR 100-2300 Conveying equipment: roller conveyor included CE marking: available Complete maintenance and inspection history Full latest test report Incl. conveyor belt, incl. cage Machine with water battery Machine without material hopper Levelling elements EUROMAP 12 interface Electrics Schuko socket 10A CEE socket 16A Voltage: 400 V Frequency: 50 Hz Motor current: 80 A Warranty Warranty up to first commissioning Loading / Shipping Free loading onto buyer's truck or free delivery within Germany subject to freight reimbursement Available ex stock Hanover, Germany

Condition: used, Year of construction: 2004, machine/vehicle number: 257253, Clamping force: 13,000 kN, total weight: 69,000 kg, including spraying unit WOLLIN, deburring press REIS TKP3, serial number: 181013, year of manufacture: 2004, weight: 680 kg, industrial robot REIS V60, serial number: 541010, year of manufacture: 2004, machine weight: 1,950 kg, melting and holding furnace STRIKO WESTOFEN W1200SL Pro, year of manufacture: 2004, serial number: 7961, furnace chamber volume: 970 dm³, empty weight: 3,100 kg, heating capacity: 22 kW, machine out of service, not ready for operation. Nedpfezhaydsx Aa Rolf

Condition: reconditioned (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 341883, TECHNICAL SPECIFICATIONS Capacities: Maximum turning diameter 270 mm Maximum diameter above the cross slide 160 mm Center height above the cross slide 83 mm Maximum diameter above the machine bed 430 mm Turning length (depending on equipment) 630 mm Headstock: Standardized spindle nose, for the use of various chucks and mandrels with adapter accessories. Accessories for SCHAUBLIN chucks B45/F66 Maximum bar capacity, dia. 36 mm/60 mm Automatic chuck, standard dia. 210 mm Direct drive by AC motor, power at 100% / 50% duty cycle 15/18.5 kW Maximum torque at 100% / 50% duty cycle 135/165 Nm Maximum spindle speed 4000 min-1 Spindle positioning, increment 0.1° C-axis: Programmable increment 0.001° Spindle lock 80 Nm Pneumatic clamping cylinder 3400 daN Cross slide: Transverse travel, X-axis 230 mm Resolution along the radius 0.0005 mm Drive by AC motor, rated torque 3 Nm Ball screw, X-axis pitch 32 x 5 mm Longitudinal travel, Z-axis 720 mm Resolution 0.001 mm Drive by AC motor, rated torque 6 Nm Ball screw, pitch 32 x 10 mm Feeds: Working feeds, X/Z axes, stepless 0-5000 mm/min Rapid traverse rates, X/Z axes 8/10 m/min Feed force, X/Z axes 420/670 daN Turret system: Number of tool stations 12 Nedpfezb U Epjx Aa Rslf Number of rotating tool stations 6 Drive by AC motor, intermittent duty power 3.7 kW Maximum intermittent torque 36 Nm Maximum drive speed 5000 min-1 Standardized tool holder 0VDI 30 Maximum cross-section of cutting tools 20 x 20 mm Integrated coolant system Indexing in both directions of rotation Coolant system: Tank capacity 120 liters Pump flow rate 10 l/min Pressure 5 bars Inventory 2230043 including: 1 Fanuc 18i control unit 1 A2-6 headstock 1 VDI 30 turret with 12 positions for 6 rotating tools 1 pneumatically operated steady rest 180-65.200 1 SCHUNK Rota-s 200-52 A2-6’’ 1x3 jaw chuck 1 Brucker CM5 rotating center 1 ESX-25 radial drilling and milling head, max speed 5000 min-1, without collet EX ref 4100.00552 1 ESX-25 axial drilling and milling head, max speed 5000 min-1, without collet EX ref 4100.00550 1 KENNAMETAL ESX-25 dito, without collet EX 1 EWS ESX-25 dito, without collet EX 4 radial tool holders, short, left-hand, Form B2 ref 4100.0100 1 ESX-25 tool holder, Form E3 with EX25 collet and Ø 5 mm collet 1 dito without EX25 collet 3 threading collets Ø 4.5 – 6 and 8 mm 1 tool holder for indexable insert drills, bore Ø 40 mm, Form E1 ref 4100.00124 1 dito bore Ø 32 mm ref 4100.00107 1 dito bore Ø 20 mm ref 4100.00105 1 boring bar tool holder, bore Ø 8 mm, Form E2 ref 4100.00108 1 dito Ø 10 ref 4100.0109 1 dito Ø 12 ref 4100.0110 2 dito Ø 16 ref 4100.0111 1 dito Ø 20 ref 4100.0112 1 dito Ø 25 ref 4100.0113 1 dito Ø 32 ref 4100.0115 1 dito Ø 32 GARANT, long 5 steel protection plugs, Form Z2 ref 4100.00130 1 axial tool holder, left-hand, force C4 ref 4100.00103 1 CM 5 pneumatically operated steady rest ref 180-65.200 1 separate support for microscope ref 180-60.005 1 coolant system OPTION 1 3-jaw hinged center for Ø 30 – 120 mm ref 180-70.200 CHF 2'500.-- + VAT Unless otherwise stated, the technical data is provided without guarantee.

Year of construction: 2006, condition: excellent (used), Fly wheel diameter : 800 mm Njdpfx Aaslk Ilyj Rslf Engine size : 4 Kw Tilt of table : 0 - 45 degree CoMaFer feeder with adjusteble speed, rubber feed wheel ( Year 2020 ) Maximum cutting hight : 680 mm Maximum cutting width : 750 mm Machine measures : L 1400 x W 1000 x H 2700 mm Request live video presentation on WHATSAPP

Year of construction: 2003, condition: used, machine/vehicle number: M00543, Rated force: 2,500 kN, rated power: 18.5 kW, machine weight: 25,000 kg, stroke rates in continuous operation: 19-57/min, max. stroke rates in single-stroke operation: 35/min, dwell time: 0.245 s, stroke length: 19-250 mm, max. installation space: approx. 480 mm, table size: approx. 900x1,200 mm, upstream light curtain, two-hand operation, separate control panel, control unit BEUTLER DATAPLUS 200. Nljdpfx Aezqzc Sea Rof

Condition: excellent (used), Year of construction: 1994, functionality: fully functional, pressing force: 200 t, stroke length: 400 mm, table width: 1,600 mm, table length: 1,400 mm, working height: 730 mm, Equipment: safety light barrier, Müller Weingarten press line: KE 200-16/14.3.1 - 200 tons KE 300-16/14.2.1 - 300 tons KE 200-16/14.4.1 - 200 tons KE 200-16/14.5.1 - 200 tons The presses have a common housing and fan system. The remaining elements are independent, which will allow you to work on the presses individually. Also, each press is controlled individually Press in very good technical condition for sale from a liquidated press in Poland Modernized in 2018-2023. New Simatic S7 control system and new electrical cabinet. Optical barriers installed. Possibility to check the machine in operation - The press is still connected to the power supply. Müller Weingarten press line KE 200-16/14.3.1 - 200 tons KE 300-16/14.2.1 - 300 tons KE 200-16/14.4.1 - 200 tons KE 200-16/14.5.1 - 200 tons The presses have a common covers and fan system. The rest of elements are independent, which allows for individual work on the presses. Also, the control of each press is individual A presses in very good technical condition for sale from a liquidated stamping shop in Poland Modernizes during 2018 -2023 Nlodpfsv Hqnajx Aa Ref New Simatic S7 control system and new electrical cabinet. Optical barriers installed as well. Possibility to check the machine in operation - The press is still connected to the power supply.

Condition: used, Year of construction: 2000, machine/vehicle number: 510565, functionality: fully functional, operating hours: 5,840 h, Offered for sale is an eccentric press. Make: Müller Weingarten Type: C40.2.2 Rated force: 40t Two-hand / foot control Safety light curtain by Sick Nlsdpfx Aaexvqnbj Ref Used, fully functional condition. Collection by buyer; support for disassembly/transport can be organized if needed. If you are interested or have any questions, please feel free to send me a message. On-site inspection available by appointment. Further metalworking machinery available, such as bench drills, press brakes, pillar drills, eccentric presses, heavy-duty racks, welding tables, MIG/MAG welding machines, compressors, etc. – please see my other listings. Collection only – disassembly and transport by the buyer or by agreement. If you are interested or have any questions, please send me a message. Further photos and technical details available on request. All information provided without guarantee or warranty; errors and prior sale excepted. For more inquiries, please call. Nous parlons Francais / Мы говорим по русски We speak English / Noi vorbim românește Viber / WhatsApp / Skype We can arrange all customs and registration formalities for an additional fee. We can also deliver vehicles to the port for an additional fee.