Pellet press-complete line

Nova pellet N-MIDI 90

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included) Hodpfx Adswp Rqfo Hsff

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. Hsdpfx Adefz U S Eo Hsff - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Condition: ready for operation (used), Year of construction: 2002, There are zwei identical vertical bag filling machines available, weight: 1.1t. Hfodpfx Asnfvxzsd Hjf

Condition: ready for operation (used), Including Ascending Conveyor SBM 45 and Counting Machine ZMR 3/ 3-130. Hodpfjhncwisx Ad Hoff

Year of construction: 1979, condition: good (used), Underfloor circular saw, crosscut saw, pull saw, miter saw, panel saw, table saw, aluminum circular saw, panel saw Hjdpshfufgefx Ad Hoff -Manufacturer: Martin, panel saw type T 70 with automatic feed -Engine power: 11 kW -Speed: 1445 rpm -Saw blade: Ø 410 x 5 mm -max. Cutting height: 90° 140 mm / 45° 110 mm -Miter cut: up to 45° -Sliding table: 355 x 1500 mm -Dimensions total 2275/2010/H1400 mm -Weight: 1058 kg

Condition: used, Year of construction: 2013, functionality: fully functional, type of input current: three-phase, sheet thickness steel (max.): 3 mm, overall weight: 15,000 kg, input voltage: 400 V, bending angle (max.): 180 °, working length: 3,200 mm, working range: 3,200 mm, Equipment: documentation/manual, safety light barrier, Technical features: Year 2013 Hedswq Rumspfx Ad Hjff Working length 3200 mm Maximum sheet thickness (iron 400 N/mm2) 3.00 mm Maximum sheet thickness (stainless steel) 2.00 mm Maximum sheet thickness (aluminum) 4.00 mm Maximum bending height on four sides 250 mm Upper jaw stroke 650 mm

Year of construction: 2017, condition: ready for operation (used), A spinning, drawing and winding line for the production of monofilament yarns, multifilament FDY and POY is available. Spinning positions: 24, yarn ends: 192, drafting: cold and hot godets, package change: without yarn breakage, number of godets heated/cold: 50/50, number of winders: 24 (+2 reserve winders). Including various spare parts for the machine and electronics. Documentation available. On-site inspection is possible. Hedpfx Ajuanq Tjd Hoff

Condition: used, 72″ x .187″ x 50,000Lb Paxson Loop Slitting Line Make: Paxson Material Width: 12″ – 72″ (Uncoiler 60″) Material Width: .010″ – .187″ Coil Weight: 50,000Lb Coil ID: 20″ – 24″ Coil OD: 72″ Speed: 500 /1000 fpm Direction: Right to Left Material Strength: 40,000 yield / 50,000 psi shear Material: CR, HR, Galvanized Entry Transfer Cart Entry Coil Car Hedpfjihf Ufjx Ad Hoff Mandrel Uncoiler Powered Hold-Down Roll Powered Expansion Sliding Base Hydraulic Peeling Table Driven Pinch Rolls

Year of construction: 2002, condition: good (used), functionality: fully functional, Drum dryer for wood sawdust and chips with capacity up to 15t/h. Hodpfxevx S Hno Ad Hoff Condition - fully functional.

Condition: like new (used), Year of construction: 2018, We offer You line Cabinplant with Multivac for snack packing. Production date of all machines year 2018. Line consisting af -Cabinplant 1 line elevator -Cabinplant 3 line elevator Hsdopxm Ugepfx Ad Heff -Multihead weigher Cabinplant MHW 10 24 -Multihead weigher Cabinplant MHW 10 32 -KEN hygiene system EWD 50 -Platform with stairs -Cabinplant distribution tools 2 pcs -Multivac R245 Type ASE 500, gas, vacum, without a vacum pump The set worked only during device tests, working for approximately 100 hours. The line was dismantled by the manufacturer's services: Cabinplant and Multivac.