Firewood harvester combine

Posch Spaltfix K500

Condition: excellent (used), Year of construction: 2013, Cutting line: ERLENBACH mod.ESA 5 (used for less than a month). Year of manufacture: 2013 Kodpfjv Hm A Tox Aayodw Packing machine, model PPZA-1300/6 (used for less than a month). Year of manufacture: 2011 - For blocks max. L x B x H: 5100 x 1260 x 1260 mm - Horizontal cut: max. 61 oscillating wires - Vertical cut: max. 11 wires - Cutting speed: 1,5 m/min. - Automatic wire setting - Waste grinding (bottom, top, side)

Condition: excellent (used), We offer for sale the following Gránit-Mill 90 wood pelletizing presses, in the condition shown in the pictures, after the pelletizing plant has ceased operation. The machine is made in Hungary, our company has an excellent relationship with the manufacturer, and we can help you purchase parts. Drive and sticker handling is similar to the old CPM machines. Kdjdpfx Ajp T Twueayjw The presses (with pine) are capable of 1.2-1.5 t/h/pc. Price: €29 900/press €49 900/ 2 presses Included in the price: pre-tank control cabinet dosing screw permanent magnet conditioner press motors pre-tank 1.1 kW feeder 1.5 kW conditioner 15 kW tablecloth 0.55 kW main engine 90 kW 3 stickers all three are made by La Meccanica barely used It has a 6 x 45 mm hole for pine 2 sets (total of 4) notched collars spare parts screws nuts breaker pin assembly aids Status: Engines and drives intact. Both machines tested. It is recommended to replace the neck bearing of the right machine. Smaller parts (such as the pellet cutter) must be replaced. There is no water supply, the place is prepared. The greasing method is manual, but central greasing can be easily installed. Summary: The machine on the left can be put into production immediately. It requires a minor service on the right side. If necessary, the machine can be tested at a pre-arranged time. Not in production, must be prepared. It is possible to check the mechanical durability and volume density of the produced pellets on site!

Condition: new, Year of construction: 2024, ♻ The MONSTER is a hybrid machine with two shaft PRE- SHREDDER P150 TWIN (with two reduction gearboxes) combined with one shaft SHREDDER SD90XL for efficient shredding of various types of pallets, styroform, plastic, waste, scrap and electrical devices. ✔ Power: 30 kW + 1x 5,5 kW-9,2 kW (shredder + pre-shredder) ✔ Shaft length: 870 mm + 1580 mm (shredder + pre-shredder) ✔ Shaft diameter: 270 mm + 355 mm (shredder + pre-shredder) ✔ Shaft RPM: 80-120 + 5,3-10,3 rpm (shredder + pre-shredder) ✔ Number of cutting knives: 2x19 + 12/12 (shredder + pre-shredder) ✔ Granulation: 10-50 mm ✔ Capacity: up to 60 pallets/h* ✔ Material: Pallets, styrofoam, electronic waste, plastics, wood,... ✔ Filling opening: 2072 x 1070 mm ✔ Dimensions L/W/H: 3,73/1,78/2,67 m Kedohwwplspfx Aaysdw ✔ Weight: 4200 kg 2 years warranty or 2000 working hours

Year of construction: 1979, condition: good (used), Underfloor circular saw, crosscut saw, pull saw, miter saw, panel saw, table saw, aluminum circular saw, panel saw -Manufacturer: Martin, panel saw type T 70 with automatic feed -Engine power: 11 kW -Speed: 1445 rpm Kedshfufgopfx Aayjdw -Saw blade: Ø 410 x 5 mm -max. Cutting height: 90° 140 mm / 45° 110 mm -Miter cut: up to 45° -Sliding table: 355 x 1500 mm -Dimensions total 2275/2010/H1400 mm -Weight: 1058 kg

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC80 (45kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. Kdjdpotvat Tefx Aaysw After refurbishment, this baler is sold with a 2-year warranty.

Condition: used, Granulation and packaging line. Model: HM700E PRO 11KW Year of manufacture: 2022 It includes: Hammer mill - shredder Chip mixer Chip feeder Granulator Vibrating table Kdjdpjxcy D Ejfx Aayow Product feed belt (conveyor belt) Pellet hopper with packaging equipment Bag sealer and chip moisture meter Hammer mill with cyclone Motor: 11 kW / 400 V Productivity: 300 - 700 kg / h Weight: 360 kg Soft start installed Cutting system 16 hammers Chip mixer: Volume: 1.0 m³ Chip feeder: Motor: 3.3 kW / 380V Feeds up to 800kg / h Granulator: Motor: 22 kW / 380V/50hz; Productivity: 300 - 700 kg/h Weight: 590kg Soft start installed Vibrating table: Weight 90kg Product feed belt (conveyor belt): Dimensions: 5m × 0.4m. Automated packaging equipment: Dimensions: 1, 90x2, 50x2, 30 Volume: 1.5m³ Packing in bags: 1 - 50kg Equipped with two types of scales Bag sealer 220V Moisture meter

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC Kedpfx Aewp Rqfeayedw • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price: 30,000.00 EUR (VAT is not included)

Condition: new, Year of construction: 2025, power: 45 kW (61.18 HP), ♻ The MONSTER is a hybrid machine with two shaft PRE-SHREDDER P150 TWIN (with two reduction gearboxes) combined with one shaft SHREDDER SD90XL for efficient shredding of various types of pallets. ♻ A shredding system integrated with a conveyor and magnetic separator offers a comprehensive solution for material processing and purification. ♻ The system consists of a powerful shredder combined with pre-shredder, capable of breaking down various materials, a conveyor which helps to evenly distribute the shredded material, ensuring a steady flow for further processing or disposal and a magnetic separator that efficiently removes ferrous or magnetic particles from the mixture, enhancing material purity and preventing equipment damage. Technical data: Shredder with pre-shredder: ✔ Power: 30 kW + 1x 5,5 kW-9,2 kW (shredder + pre-shredder) ✔ Shaft length: 870 mm + 1580 mm (shredder + pre-shredder) ✔ Shaft diameter: 270 mm + 355 mm (shredder + pre-shredder) ✔ Shaft RPM: 80-120 + 5,3-10,3 rpm (shredder + pre-shredder) ✔ Number of cutting knives: 2x19 + 12/12 (shredder + pre-shredder) ✔ Granulation: 10-50 mm ✔ Capacity: up to 60 pallets/h* ✔ Material: Pallets ✔ Filling opening: 2072 x 1070 mm Kjdpfxjtpwrme Aaysdw ✔ Weight: 4200 kg Z conveyor: ✔ Frequency converter (adjustment of conveyor speed) ✔ Overband magnetic separator ✔ Length: 6500 mm ✔ Width: 350 mm ✔ Capacity: 0,5 kg/s ✔ Power 0,25 kW ✔ Transport wheels 1 years warranty or 1000 working hours

Condition: ready for operation (used), Year of construction: 2015, functionality: fully functional, The Spanner plant consists of the cogenerator and the reformer. The reformer, the heart of the wood chip system, produces natural wood gas from wood chips through a controlled process. This gas is used to operate the cogenerator. The generated thermal energy can be used to heat buildings, drying plants or district heating networks, while the electricity is fed into the grid. Kdsdpfx Aaswvhf Toyjw Model: HK45 Electrical performance: 45 kW Thermal performance: 120 kW Wood chip consumption: 45 kg/h Requirements for wood chips: Grain size G30-G40 Maximum moisture 15% Fine dust (

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, machine/vehicle number: 3294, type of input current: three-phase, power: 90 kW (122.37 HP), input voltage: 400 V, We are selling line from Nova pellet, 2019 production and 2020 first year of production start. -Pellet press N-MIDI 90 KW 12.500 hrs(very good and daily maintaince, 2025 new rollers and die, 200 hrs old Main tooth-belt)-2019 year -Transporting vertical elevator ca 10m height-2019 year Kdedpfx Aowahhcsayew -Cooling tower N-CO700-2019 year -Control cabinet-NEW UNUSED -Heavy duty hammermill Miller M16(37kW electric engine)-NEW UNUSED We are selling only items above(without cyklon, filters etc.)! Line is in very good condition and had very good daily maintaince. For further informations, please write or call on our contact.