Baler

Presona AB LP 85 VH1

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Fgodpfx Aaevwlqqs Noi Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Fgodjvgrh Ujpfx Aa Noi Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: reconditioned (used), Year of construction: 2002, operating hours: 43,954 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, overall weight: 50,800 kg, oil tank capacity: 3,100 l, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002 Operating hours 43,954 hours, stand March Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 112 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine is currently in our workshop for overhaul. We assume that the press will be completely overhauled in approx. 4 weeks and can then be tested. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Fedpfx Aju Thgzja Nsgi

Condition: reconditioned (used), power: 11 kW (14.96 HP), operation weight: 8,000 kg, Horizontal baler DIXI 80 SLD 2018-2021 Year of construction Semi-automatic 80-tonne baling system for the economical volume reduction of residual materials (recyclables) in industry and trade: Cardboard packaging Tetra packaging Fgedpfx Asqa Dq Dja Nji Films PET bottles Foam Insulation boards and other compressible materials. Machine dimensions L x H x W approx. mm: 4,320 x 1830 x 2,154 mm Filling opening W x H (standard) mm: 1,040 x 1,110 mm Machine weight approx. kg: 8,000 Press force max. kN: 80 t / 800 kN Ironing cycle (average value) approx. s: 35 Bale size W x H x L approx. mm: 1,120 x 1,120 x 1,200 Bale weight (depending on material) approx. kg: 550 - 650 Binding: manual Number of bindings: 4, with wire with Quicklink wire Drive power: 11 kW; 400V/32A The presses are tested and functional and are offered with a fresh UVV and inspection in accordance with DGUV regulation 3. The Dixi 60SLD is ready for immediate use. On request, the Dixi 60 SLD can be completely overhauled for an additional charge. This includes: Replace all hydraulic hoses. Change the hydraulic oil and check the hydraulic unit. The hydraulic cylinders are checked and replaced if necessary. Net price plus VAT and possible transportation. The operating instructions are available and are supplied as a PDF file and in paper form.

Condition: as good as new (ex-display), functionality: fully functional, power: 242 kW (329.03 HP), gearing type: automatic, fuel type: diesel, overall weight: 24,200 kg, empty load weight: 24,200 kg, operation weight: 24,200 kg, Year of construction: 2024, operating hours: 155 h, Equipment: ABS, UVV, additional headlights, air conditioning, all wheel drive, cabin, cruise control, differential lock, low noise, onboard computer, pallet forks, standard shovel, Hyundai HL970A Year of manufacture: 2024 Operating hours: approx. 155 Cyclone air pre-filter Air compressor for cab Standard brake accumulator Safety boom (general) Remote-controlled door LED cab lights (4 front) Voltage converter 24V -> 12V LED beacon All-around view monitor (AAVM) Radar LED driving lights LED combination lights Second monitor Single brake pedal Piping for 3rd control circuit Central lubrication system Bekamax Piping for quick coupler Joystick steering Standard lift frame With emergency steering Ride control 5-speed transmission (torque converter) Quick coupler ISO SW (Volvo type attachment) Triangle TB5 radial tires Transmission guard Control block (MCV) with 3 sections Air-suspended heated seat Fgedpfew Rdt Ujx Aa Noi Hydraulic oil - VG46 Accelerator pedal with ECO switch Without Bmair filter system Standard paintwork Fingertip 3-lever electric control Rear window roller blind Wheel chock Axle cooling - front & rear Hydraulic differential Rear axle without differential lock Universal bucket 4.2 m³, with bolt-on edge/blade Universal bucket 4.6 m³, with teeth