CNC milling and boring machine

SKODA WD 200

Condition: excellent (used), Year of construction: 1983, Faceplate diameter: 1250 mm Max. swing diameter: 1400 mm Max. swing height: 1160 mm Max. ram stroke, vertical / horizontal: 755 / 840 mm Table load capacity: unlimited Faceplate speed range: 5.6 - 300 rpm Vertical slide angular adjustment: 45° Feed rate range: 0.044-8 mm/rev Rapid traverse rate: 2 m/min Drive power: 55 kW Footprint L x W x H: 2660 x 2710 x 3360 mm Total weight: 16,500 kg Accessories / Special features: • 2-axis digital display, manufacturer: ACU-Rite • Faceplate, Ø 1250 mm, with 4 chuck jaws • 5-position turret • Taper turning • Profile turning Ljdjy Ex Epspfx Aiqjhl Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany

Condition: used, WEBSTER & BENNETT EV 36” HIGH SPEED VERTICAL BORER MAKE WEBSTER & BENNETT, MADE IN ENGLAND MODEL EV 36” TABLE DIA 915 mm SWING 1168 mm HEIGHT UNDER RAIL 533 - 1016 mm SPEED 13.5 - 300 rpm FEED RATE 0.005-0.250 inch/min Lhjdpsxp Na Njfx Aiqjl MAIN SPEED 40 HP PLUS HIGH SPEED TAABLE EV SERIES MACHINE ELEVATING RAIL SAFETY GAURDING SET OF JAWS FULLY FUNCTIONAL GOOD SLIDES

Condition: excellent (used), Year of construction: 2009, turning height: 1,280 mm, total height: 5,600 mm, total width: 3,850 mm, total length: 4,260 mm, rotary table diameter: 1,400 mm, workpiece diameter (max.): 1,600 mm, overall weight: 21,500 kg, CNC Vertical lathe Fremtas - 16FR3 MACH-ID 9467 Make: Fremtas Type: 16FR3 Control: FAGOR 8055 TC Year: 2009 Work load 6300 Kg Cross rail adjustment 660 mm Feed rate cross rail 0 - 400 mm/Min Feed rate 0 - 3000 mm/Min Rapid feed 0 - 8000 mm/Min Central lubrication Chip conveyor RAM with Sandvik COROMONT C8 Tooling C8 with double connector Ca 10 units CAPTO Tool system 4 extra heavy duty jaws Max. turning Ø: 1600mm Table Ø: 1400mm Horizontal movement support:1000mm Speeds / ranges: 1 - 200Rpm Power: 75kW Maximum turning height: 1280mm Vertical movement support: 700mm Length: 4260mm Width: 3850mm Height: 5600mm Lsdpjy Htilsfx Aiqshl Weight: 21500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 1999, functionality: fully functional, turning length: 3,000 mm, turning diameter: 1,000 mm, spindle bore: 197 mm, Upon request, videos of the machine in operation can also be provided. Maximum turning length: 6000 mm Turning diameter: over cross slide: 1000 mm over bed: 1250 mm Spindle bore: 197 mm Spindle speeds: 0 – 665 rpm Faceplate diameter: 1200 mm Workpiece weight: 15000 kg between centers Motor power: 55 kW / 74 hp 3 gear stages: 1.5-55 / 50-180 / 180-665 rpm Accessories: Sauter 4-position tool turret (rotation defective) Tailstock (hydraulics partially defective, pressure loss) Chip conveyor 2 chip guard doors (incl. safety device) Lhedeyr N N Rspfx Aiqsl 4-way bed machine (flat bed) LED lighting

Condition: used, faceplate diameter 3100 mm swing diameter 3600 mm turning height 3600 mm control Fagor 8035 table load 35 t turning speeds 0,32 - 40 U/min max. ram stroke 3000 mm table load 35 t turning speeds 0,32-40 U/min total power requirement 70 kW 2x Ram head 250 x 250 mm Chip conveyor Mist extraction unit Coolant system The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. Ljdpeyqt Hdjfx Aiqohl We look forward to your visit. Your Markus Hirsch Team

Condition: used, Technical details: turning diameter over bed: 3800 mm turning diameter over slide rest: 3200 mm turning length: 12000 mm faceplate turning speed range -stepless-: 2 - 200 U/min max. workpiece weight: 90.000 kg bed width: 4000 mm Lhsdpfx Aox Ngzyeiqjl 2 steadies *

Condition: refurbished (used), Year of construction: 1985, functionality: fully functional, travel distance X-axis: 1,200 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 700 mm, spindle speed (max.): 1,500 rpm, spindle speed (min.): 5 rpm, feed length X-axis: 1,200 mm, feed length Y-axis: 2,000 mm, feed length Z-axis: 700 mm, feed rate X-axis: 1,000 m/min, feed rate Y-axis: 1,000 m/min, feed rate Z-axis: 1,000 m/min, total width: 4,000 mm, San Rocco Horizontal Boring Machine Fully overhauled San Rocco horizontal boring machine, originating from a high-end aerospace manufacturing facility. The machine is equipped with a Siemens SINUMERIK 840D CNC control system with SIMODRIVE 611 drive technology. The machine is fitted with modern digital drive systems and is designed for high-precision multi-axis machining in continuous operation. It was fully overhauled in 2024, including brand-new telescopic covers on all axes, as well as numerous additional essential refurbishments to the hydraulic system, CNC components, hoses, seals, and related assemblies. Travels X-axis (longitudinal): 1,200 mm Y-axis (cross): 2,000 mm Z-axis (vertical / spindle axis): 700 mm Spindle Data Boring spindle diameter: 100 mm Tool interface: ISO 50 Milling spindle diameter: 185 mm Spindle axial travel: 700 mm Feeds and Rapid Traverses Automatic feeds (spindle and vertical axis): 2 × 1,000 mm/min Rapid traverse (spindle and vertical axis): 5,500 mm/min Distances Minimum spindle height above table: 0 mm Maximum spindle height above table: 1,500 mm Maximum distance from spindle nose to table center: 1,850 mm Spindle Speeds Torque range: 5 to 14 rpm Continuous power range: 15 to 1,450 rpm Number of gearbox ranges: 4 Speed ranges: 6–51 / 49–160 / 140–460 / 440–1,450 rpm Table Data Rotary table size: 1,100 × 1,300 mm Longitudinal travel: 1,200 mm Cross travel: 2,000 mm Table Feeds Automatic feeds X and Y: 1,000 mm/min Rapid traverse X and Y: 5,500 mm/min Table Rotation Continuous rotation: 30 to 100 degrees per minute Rapid rotation: 5,000 degrees per minute Drive System Siemens SIMODRIVE 611 E/R module 36/47 kW LT modules 108 A and 2 × 25 A Lifting and Transport Data Group 1 Steel bar Ø 70 mm, length 1,600 mm Steel bar Ø 70 mm, length 2,400 mm Lodpfx Aex Rhlcoiqshl Four spacer rings for lifting slings Four steel slings Ø 22 mm Weight approx. 12,500 kg Group 2 Two steel slings, minimum Ø 18 mm Weight approx. 3,500 kg Group 3 Manual lifting Weight approx. 1,300 kg Condition The machine is in very good technical condition and can be inspected and tested under power by appointment.

Condition: new, Year of construction: 2025, functionality: fully functional, turning height: 1,600 mm, turning diameter: 2,000 mm, CNC Vertical Turning Center Model: VTC-16/20R with Fanuc 31i-B Table Diameter: Ø1,600 mm Max. Swing Diameter: Ø2,000 mm Max. Turning Height: 1,600 mm Table Speed: Max. 250 rpm Table Load Capacity: 8,000 kg Table Indexing Speed: 720°/min Table Indexing Accuracy: 0.001° X-Axis (Ram horizontal): -100 mm to 1,170 mm Z-Axis (Ram vertical): 900 mm Drive Spindle Speed: Max. 2,000 rpm Ram Size: 240 mm x 240 mm Milling Spindle Taper: ISO 50 Tool Shank Size: 40 mm x 40 mm Crossrail (vertical travel): 250 mm x 3 stages (hydraulic) Table Drive Motor: AC 37/45 kW (continuous/30 min. duty) Milling Spindle Drive Power ISO 50: 15/18.5 kW (continuous/30 min. duty) Control System: Fanuc 31i-B Display Unit: 15-inch TFT-LCD Memory Capacity: 1 MB Automatic Tool Changer: 24 positions (for 7 turning tools + 1 cover + 16 milling tools) Standard Tool Holders: New 240 TCR-01 (2 pcs) Splash Guard: Table version (R-Type standard design) External Coolant System: 3 bar (80 l/min) Ljdexp Nb Tepfx Aiqehl Chip Conveyor: Hinged belt type Table Bearing Cooling Device 4-Jaw Independent Manual Chuck Foundation Anchor Bolts / Base Plates Maintenance Tools and Toolbox Hydraulic Power Unit Work Area Lighting Signal Lamp: 3 colors (green, red, yellow) Operating Manuals (English): 1 CD with Fanuc manuals and 3 books with mechanical/electrical manuals Power Supply: 220 V, 60 Hz, 3-phase Machine Color: Manufacturer standard OPTIONAL ACCESSORIES (#1) Turning Tool Holder: Type 240TCR, 4x included Rigid Tapping: 1x included OPTIONAL ACCESSORIES (#2) Automatic power-off for N.C. - on request Turning tool holder type 240TCR - on request Through-spindle coolant supply: 30 bar (pump pressure) - on request Transformer 415 V, 50 Hz, 3-phase - on request Linear scales X-, Z-axis (Fagor, Spain) - on request Workpiece measuring device - on request Tool measurement TS27R, Renishaw - on request Other information: INSTALLATION, COMMISSIONING, TEST OPERATION, AND TRAINING - not included in the price INSURANCE AND FREIGHT - not included in the price Image shows machine with pallet changer. The offered machine DOES NOT INCLUDE A PALLET CHANGER! Errors in technical data excepted. The scope of accessories is as described in the text of this article only. There is no entitlement to any other accessories, such as those shown for illustration purposes. The general terms and conditions of JS-Werkzeugmaschinen GmbH apply.

Condition: used, turning diameter 1.600 mm max. swing diameter 1.700 mm control SIEMENS - 840 D faceplate turning speed range 1 - 320 U/min Ljdpfxsvp Shgs Aiqohl rapid traverse 3.000 mm / min feed range 1 - 3.000 mm/min size of pallet 1.168 mm numbers of pallets 2 main drive 55 kW Vertical turret lathe with cnc | SCHIESS MOWEG - BERTHIEZ TFM 125 has been overhauled by SCHIESS MOWEG (RETROFIT) in 2007. The machine video from the production plant will be shared on request. The machine is in very good condition and was in operation at an aviation company until recently. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: TFM125 | TFM-125

Condition: good (used), travel distance X-axis: 12,000 mm, travel distance Y-axis: 7,300 mm, travel distance Z-axis: 3,000 mm, total length: 30,000 mm, table length: 12,000 mm, table width: 4,730 mm, total width: 12,000 mm, total height: 10,475 mm, table load: 250,000 kg, overall weight: 400,000 kg, Make : Waldrich - Siegen - Typ : PF-F-150(1)-530/400 - No. : 11.093/0 - Age : Overhault 2004 ( Euro 2.2 Mil) X Travel : 12.000 - Y Travel : 7.300 - Z Travel : 3.000 - W Travel : 4.000 - Between column : 5.000 - Table width : 4.730 - Table length : 12.000 - Table load : 19 t / mtr. Ca. 250 ton - Table feed : 10.000 mm/min. - W axis : 3.000 mm/min. - T axis : 6.000 mm/min. - Cross adj. milling head : - Vert. adj. cross rail : - Horizontal hydrostatic spindle ram - Milling spindle Ø : 560 - Milling tool taper : iso 60 - C axis feed : 5.000 mm/min. - Milling motor : 90 kW - Spindle speed : 2.500 R/pm - Z axis stroke : 3.000 - Z axis feed : 2.000 mm/min. - Milling Küma Angle head WF2 90 kw- 450 - Milling Küma Uni. UB1D 60 kw - 2400 - Milling Küma Fixed GB1D 90 kw- 2400 - Milling Küma Angle head WF1? - Electric requirement : 3 x 400 V / 50 Hz Lsdpfx Asytrxkeiqjhl - Power requirement : 600 kVA / 630 Amp - Capacity 4.000 L coolant true spindle 20/40 Bar Machine is rebuild in 2004 by Schiess Bed – Table assembly group: * Renewal of sliding lining * Grinding of guideway * Renewal of table drive * Direct linear measuring syst. * Hydrostatic Portal and cross rail: * Modification of adjusting spindle trape Zoidal spindle was recplaced with ball screw * Direct linear measuring syst. * New drive motors for relization of higer speed on feed axes of milling support. * New milling support with hydrostatic guideways Electric system: * Complet elctric cabinet switchgear * Complet new wire * Siemens Sinumrik 840 D in 6 axis !! Equipment / parts : * Complet new raumag janich covers * Complet new double chip conveyor * Complet with big tooling packet * Complet with big mounting equipment - Under power in Europe - Free directly - Controlled axis X / Y / Z / W / C / B axis - Over all height : 10.475 mm - Over all width : 11.934 mm - Over all length : 30.000 mm - Total weight : ca. 400.000 Kg Rebuild in 2004 for EUR 2.200.000 !This CNC Waldrich Portal milling machines was used in the Energie Field for steam turbien case machining. Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!