Deephole boring machine

TBT

Year of construction: 1985, condition: used, Drilling process: single-lip gundrilling, operating method: rotating tool, number of working spindles: 1, nominal drilling depth: approx. 750mm, drilling range for solid drilling in steel: approx. 30mm, drilling range for counterboring in steel: approx. 40mm, spindle drive: 11kW, max. spindle speed range I: 1800rpm, max. spindle speed range II: 5700rpm, max. feed rate range I: 320mm/min, max. feed rate range II: 160mm/min, rapid traverse: 3.5m/min, clamping table X/Y: 420mm/1280mm, cross-slide table manually operated, max. transverse travel: 400mm, table clamping surface X/Y: 600mm/600mm, high-pressure coolant system for deep-hole drilling oil with 1000l coolant tank, flow rate: approx. 2-94l/min, max. pressure at max. flow rate: 45bar, pump power: 11kW, separate control cabinet. The machine underwent an extensive partial overhaul in 2018, during which the machine was disassembled and cleaned, all guideways and support surfaces were ground and partially scraped, motors were inspected and fitted with new bearings, the drilling spindle was fitted with new bearings, the ball screw incl. nut was replaced, the pump motor was overhauled, the wiper set was replaced, and the machine was repainted and all functions were checked and rectified. Including extensive accessories. Documentation available. Inspection possible by arrangement. Nwodpfezu Szyjx Aarsk

Condition: excellent (used), TBT T30 SERIES TABLE TYPE GUN DRILLING MACHINE Model T30-1000KTN Serial number 410.364.016 Year of manufacture, approx. 1980 Number of spindles 1 Drilling range in steel 4 - 30 mm (solid) Counter boring 40 mm Nominal drilling depth 1000 mm Slotted table size 850 long x 750 wide mm Table size overall 1100 long x 1000 wide mm Table cross movement 800 mm (approx.) Table vertical movement 400 mm (approx.) Drilling slide longitudinal travel 1450 mm Slideway width 250 mm Spindle speeds to approx. 9000 rpm Spindle motor 25 kW Total load 41 kW Supplied with: Nwsdpjzuxp Rjfx Aarsk 2 off Whip guides. Ballscrew feed. 2 Axis DRO to table Cross and Vertical, DRO to drill slide. TS25-1000 Coolant tank. Drill bushes. For Sale with Jet Machinery Ltd Jet Machinery Stock No: #27033 Machine Serial Number: 410 364 016 Cost: £17,500.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use.

Condition: ready for operation (used), Drilling diameter: 3-25mm, drilling depth: 1000mm, connected load: 36kW, control: EST, 99 drilling memory positions per program, grinding and coordinate programming, plain text programming via input mask. Accessories: paper band filter, coolant cooling system, 4-door control cabinet, high-pressure pump up to 150bar, oil tank, 1 steady rest for smaller diameters at large drilling depths, direction-adjustable holder for drill bushing holders, various drill bushing holders, long clamping table for 0-height, tailstock stop and base plate for machine vice freely movable on the additional table, matching precision machine vice optionally available. Speed, high pressure, Z-axis (feed), X/Y-axes, and W-axis (approach slide) programmable via control. CPU and card rack defective (fan fault), machine therefore not operational, drives and guideways were fully functional until last operation. An on-site inspection is possible. Nwsdpfsylbrqjx Aarjk

Condition: like new (used), Year of construction: 2022, functionality: fully functional, machine/vehicle number: 106882-11, total length: 4,400 mm, total width: 1,700 mm, total height: 2,700 mm, overall weight: 7,000 kg, The drilling process of the deep hole drilling machine utilizes the single-lip drilling method. Drilling Unit Information: - Drilling depth: 200 mm - Min./max. drilling diameter: 1–12 mm based on ST 60 - Number of spindles: 2 - Spindle distance: 200 mm - Spindle drive: 2 x 2.4/4.2 kW - Infinitely variable spindle speed: 1,000–20,000 rpm - Infinitely variable feed rate: 10–25,000 mm/min - Rapid traverse: 25,000 mm/min - Slide travel (nominal): 650 mm - Slide width: 460 mm - X-axis slide travel: 200 mm, rapid traverse: 25,000 mm/min - Y-axis slide travel: 200 mm, rapid traverse: 25,000 mm/min Nedpfxowh Rp Ej Aarowk Fluid Information: - Coolant supply: deep hole drilling oil - Tank capacity: 500 liters - 1x automatic filter, filter performance: 50 l/min - 1x monitoring filter - 2x ELB drilling oil supply lines - 1x flow divider - 1x air cooler with recirculation pump - 1x electrostatic oil mist extraction unit - 1x scraper belt chip conveyor - 1x hydraulic unit and pneumatic unit/equipment - 1x sump pump - 3x submersible pumps - 1x radial piston pump with remote adjustment: Delivery rate: 1–38 l/min Pump drive: 7.5 kW Spindle Unit: - Motorized spindles with frequency-controlled, infinitely variable speed regulation - Spindle head with connection for tool holder - 2 x tool holders for collet sleeves according to VDI 3208 SE10x60, permanently bolted to the spindle head of the motorized spindle Drill Bushing Carrier: - The drill bushing carrier is positionable via the NC axis - Cast iron design, mounted on linear guideways - W-axis drive via AC servomotor and ball screw with indirect, absolute position measurement system Workpiece Slide: - The workpiece slide is designed as a cross-slide for vertical and horizontal positioning of the workpiece, for mounting clamping plates or special fixtures - Base unit in cast iron design with linear roller guideways - X and Y axes driven by AC servomotors and ball screws - Direct, absolute position measurement systems. Table plate with clamping or alignment grooves Clamping Table with NC rotary indexing device for positioning: - With rotary and swivel axes - Hydraulic clamping in rotary and swivel axes Technical Data: - Swivel range: 270º - Rotary range: 360º - Center height: 25 ± 0.02 - Spindle distance: 200 ± 0.005 - Indexing accuracy: rotary axis ± 15" / swivel axis ± 30" Electrical Equipment Information: - 1x drilling process monitoring - 1x CNC control 840D (Solution Line) Connection Data: - Operating voltage: 3AC 400V ± 10% - Frequency: 50 Hz - Control voltage: 24 V DC - Total rated power: 25 kW Additional Machine Equipment: - 2 x holders for resilient drill bushing holders, arranged on the drill bushing carrier - For max. drilling Ø18 mm.

Condition: used, functionality: fully functional, machine/vehicle number: 106341-11, Year of construction: 2005, overall weight: 8,000 kg, total height: 2,700 mm, total length: 5,660 mm, total width: 3,956 mm, The drilling method of the deep hole drilling machine is single-lip drill deep hole drilling. Drilling Unit Information: - Number of spindles: 1 - Infinitely variable spindle speed: 300 – 8000 rpm - Spindle drive power: 7.5 kW - Max. drilling depth: 800 mm - Drilling diameter min/max: 3 – 25 mm based on ST 60 - Max. twist drilling: 25 mm - Max. thread tapping: M24x3 - Milling material removal rate: 150 cm³/min Travel Paths: - X-axis travel: 800 mm - Y-axis travel: 400 mm - Z-axis travel: 630 mm - W-axis travel: 800 mm Travel Speed: - X-axis speed: 15,000 mm/min - Y-axis speed: 15,000 mm/min - Z-axis speed: 15,000 mm/min - W-axis speed: 15,000 mm/min Fluid Information: - Coolant supply: deep hole drilling oil - Tank capacity: 800 liters - 1x scraper belt chip conveyor - 1x hydraulic unit and pneumatic system/equipment - 1x submersible pump: Pumping capacity: 200 l/min - 1x low pressure pump: Pumping capacity: 100 l/min Pump drive: 1.7 kW - 1x compact belt filter: Filtration capacity: 120 l/min for processing steel/non-ferrous metals - 1x radial piston pump with remote adjustment: Pumping capacity: 2 – 94 l/min Pump drive: 7.5 kW Spindle Unit: - Cartridge spindle design with drive housing and spindle drive with gearbox. Spindle bearing with precision angular contact ball bearings and lifetime grease lubrication. Milling and Drilling Spindle Unit: - For conventional machining - Spindle head with HSK 50 tool holder Drill Bush Holder: - Design as 2-position turret with electric swivel mechanism - Locating position via Hirth coupling - Turret head with fixtures for: Guide bushes for deep hole drilling Milling and drilling spindle unit for conventional machining Pickup Tool Changer: - For conventional tools and drill bushings - Disc magazine design with 20 stations including feed stroke Automatic Tool Changer for Deep Hole Drilling Tools: - Fixed ELB column magazine for at least 5 tools including automatic tool clamping for HSK holders Clamping Table with W-Axis and NC Rotary Table: - Length/width: 800 x 600 mm - Positioning accuracy: B-axis +/- 30" - Centric payload: 1,500 daN Workpiece Clamping Device: - 1x tailstock with manual clamping movement - 1x NC dividing unit (A-axis) with manually operated two-jaw chuck for workpiece clamping - 1x base plate for mounting and clamping drill bushings + supporting prisms Electrical Equipment Information: Nwjdpfow E H E Rex Aarsk - 1x CNC control Sinumerik 840D (digital complete system), including PLC S7-300 Connection Data: - Operating voltage: 3AC 400V ±10% – Frequency: 50 Hz - Control voltage: 24 V DC - Total connected load: 25 kW

Condition: used, Year of construction: 1996, core drilling diameter max. 25 mm bore depth 1000 mm swing diameter mm total power requirement 25 kW weight of the machine ca. 12,5 t Njdpfxet Hw Aye Aarowk dimensions of the machine ca. m T B T (Germany) CNC-Controlled Horizontal Deep Hole Drilling " Centre " Model BWP 250 Year 1996, but reconditioned mechanically and electrically in 2006 _____ Working range: X Axis, machine column cross 2,000 mm Z Axis, drilling slide horizontal 1,200 mm Drilling depth 1.000 mm Y Axis, drilling slide vertical 1,100 mm Table clamping area 1,200 x 2,000 mm Drilling capacity in solid material, approx. 4 - 25 mm Tool holder taper HSK 50 Spindle speeds 1.260 - 15,000 rpm Feed rates / quickfeed, XYZ, infinitely variable 100 - 10,000/15.000 mm/min. Force rate of feed motors 27 Nm / 1.000 daN Spindle drive steplessly adjustable 7 kW Total electrical load, approx. 30 kW - 400 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features: " Ideal machine for the complete processing of large workpieces like tool a. dies (cooling holes) mould- and dieplates, hydraulicparts etc. by means of deep hole drilling up to 25 x 1.000 mm, face milling up to Ø 60 mm, spiral twist drilling, counterboring and threading up to M 24 x 3 mm. " SIEMENS Continuous Path Control in 4 axes Model 840 D, with process monitoring for coolant pressure, operation data control function, toollife, feed force,Error diagnostics and easy dialogueprogramming directly on the panel, etc. " High Frequency Spindle Make GAMFIOR with stepless speeds " Hydraulically movable drill bush carrier, swivels 90° for holding gun drills (ELB) or picking up regular tools from the tool changer like twist drills, milling tools, taps, etc. " With automatic tool changer made by MIKSCH, Model CTM 40, using a 12-position tool changer, which is mounted on the r.h.side of machine housing, in fixed position, only moving forward and backward for tool changing operation. " Built-on indexing table as B-Axis made by FIBRO Model RTN 400 = 420 x 420 mm, " Extra Rotary Table made by FIBRO with Ø 1.000mm, for indexing 3-144 positions " Built-in coolant device with chip conveyor and various filters. " 2 steady rests. " Completely covered working area with access at the front and at the side. Condition : Very good condition. This is a rare and valuable machine. Under Power Delivery : immediately ex our Stock Payment : Net, after conclusion of contract.

Condition: not inspected (used), Year of construction: 1970, - Drilling diameter: 5-30 mm - Drilling depth: 750 mm - Filter Nsdpfxjxzz Hs Aarowk - Pump

Condition: used, Year of construction: 1991, operating hours: 58,273 h, functionality: fully functional, machine/vehicle number: 11.05149.028, drilling depth: 6,000 mm, feed length Z-axis: 6,000 mm, total length: 35,000 mm, total width: 4,500 mm, total height: 3,000 mm, overall weight: 30,000 kg, travel distance Z-axis: 6,000 mm, spindle speed (max.): 2,000 rpm, drill diameter: 64 mm, The machine is ready for operation; however, we do not have sufficient demand to utilize it to its full capacity. Nodpey Tvy Hjfx Aarjwk

Condition: good (used), drilling depth: 1,500 mm, feed length X-axis: 2,000 mm, feed length Y-axis: 1,300 mm, feed length Z-axis: 1,500 mm, Manufacturer: TBT deep drilling technology Type: BW 250-S Control: SIEMENS 840D Year of manufacture: 2007 Drilling, Milling, Tapping for heat exchanger bases and plates Swivable A Axis + 25 to - 15 Degrees Filtration and Coolant system 1000 L Cip conveyor 2000 x 1200 height out put Milling tool changer Tower Station 20 positions Capacity ELB Drilling 3 - 35 mm Capacity Milling 250 ccm/Min Feed rates all axis 15,000 mm/Min X-Y-W-Z Cutting hours approx. 15,000 Large tooling package Specifications Metric US Standard Max. Drill Ø steel 40 mm Drilling depth 1500 mm X - axis 2000 mm Y - Axis 1300 mm Z-axis 1500 mm W-axis 750 mm Table load 15000 Table dimensions / L x W or ø 1600 x 1200 mm Spindle mount HSK 63 Mk Spindle power 11 kW Speed 8000 Rpm Dimensions (estimate) Length 7200 mm Width 7800 mm Height 4250 mm Weight 23000 kg Please note: The information on this page is believed to be accurate and is provided by us and, where possible, from the manufacturer. The information is provided in good faith but accuracy cannot be guaranteed. Accordingly, it will not constitute a representation or contractual terms. We recommend that you check all important details. Nwjdpjv A Uw Djfx Aarok

Condition: good (used), functionality: fully functional, drilling depth: 1,000 mm, FOR SALE: TBT T 30 – 1000 KT Deep Hole Drilling Machine High-quality German engineering for precision drilling Overview: Available for purchase is a robust and reliable deep hole drilling machine from the renowned German manufacturer TBT Tiefbohrtechnik. As a global leader in deep hole drilling technology, TBT machines provide unmatched precision for long-hole operations. Technical Specifications: Model: T 30 – 1000 KT Year of Manufacture: 1977 Max Drilling Depth: 1000 mm Drilling Diameter: approx. 4 – 30 mm Rated Power: approx. 20 kW Operating Voltage: 380 V / 50 Hz Nodpfx Aaoy Rvc Ajrswk Machine Type: Knee-table (KT) design for flexible clamping. Key Benefits: Solid Construction: German heavy-duty build ensures superior stability and accuracy. High Performance: The 20 kW motor provides ample power for various metal alloys. Versatile Application: Ideal for drilling shafts, molds, and other long workpieces.