Lathe accessories

Weiler Primus

Condition: excellent (used), WEILER PRIMUS Type MD-G - Centre height: 125 mm - Centre distance: 400 mm - Speed range: 40-3000 rpm - Spindle bore: 24 mm - Electric chuck guard - Multifix with tool holders - Tailstock with drill quill - Four-jaw chuck - Work lamp - Bed stop - Documentation Dimensions: LxWxH 1.3x0.8x1.6 meters / Weight: 450 kg Itjdpfxoxw H Dbe Ad Dop Errors and omissions excepted.

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and pull spindle lathe with 2 axis digital readout Heidenhain from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg Iodpfx Adeu Afqle Djtp >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 2-axis digital readout from Heidenhain >> 1 new three-jaw chuck 125 mm with 2 sets of jaws >> collet chuck device new with collets new from 3 mm to 25 mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Back plate To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: used, L + Z Lathe WEILER Type LZ PRIMUS GS Machine no. No. 2461 Year of construction approx. 1990 Center width 400 mm Turning diameter over bed 250 mm Center height above bed 125 mm Turning diameter over support 140 mm Center height above support 70 mm Spindle bore 24 mm Spindle speed 60 - 3000 rpm 18 steps Feed lengthwise and flat Chuck flange short taper DIN 55022 size 4 Inner tailstock taper MK 2 Drive power 1.1 kW and 1.5 kW pole-changing Mains connection 380 Volt, 50 Hz - 3-axis digital readout FAGOR, type 30i-T-B - Spindle speed via 2 motor speeds and 9 gear stages - 3-jaw lathe chuck RÖHM Ø 125 mm with stepped jaws - MULTIFIX quick-change tool holder with 1 interchangeable cassette - Set of collets Ø 1 / 3 / 4 / 5 / 7 / 8 / 10 / 14 / 15 / 16 / 17 / 19 / 20 / mm - 1 centering tip for collet chuck holder - Emergency stop - Hinged chuck guard Iedpfx Asrtd Uwed Dstp - Splash guard - Machine light - electrical diagram - Machine mounted on a steel plate (steel plate L x W x H 1200 x 500 x 30 mm, 140 kg) Space requirement L x W x H 1200 x 900 x 1560 mm Weight 520 kg good condition

Condition: ready for operation (used), Year of construction: 1989, functionality: fully functional, For sale is a lathe of the brand Weiler type Primus LZ-GS The machine is in very good condition Technical data Year of construction 1989 Machine no. 4443 Operating voltage 380 V Iedpeihig Isfx Ad Detp Center height 120 mm Center width 430 mm Speed:60 - 3000 rpm in 18 gear stages Spindle clearance 23 mm Short taper spindle head DIN 55027 Tailstock MK 2 Feed rates from 0.03 to 0.15 mm /rev Possible threads metric, inch, module and diametral pitch Metric thread pitches from 0.25 to 2.5 mm Length 1.2 m, height 1.3 m, depth 0.65 m Prices plus VAT Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and feed screw lathe from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm Itjdpeu Aftgefx Ad Dop >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck 160mm with 1 set of jaws >> 1 new three-jaw chuck 125mm with 2 sets of jaws >> Collet chuck device with collets from 1 mm to 20 mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Fence >> Change wheels To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and spindle lathe from the training workshop!!! Technical data: >> Year of manufacture approx. 1985 Machine no. 1191 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear stages >> Spindle passage 23 mm >> Short taper spindle head KK4 DIN 55027 Itedpfovtp Edjx Ad Dep >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 x three-jaw chuck 125 mm with 2 sets of jaws >> Collet device with Collets 18 pieces >> Mulifix size A with 3 steel holders >> Stop >> Electric spindle protection About the machine: A Weiler Primus guide and pull spindle lathe is offered in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs quietly even at high speeds. The Primus was in a training workshop. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site with power on and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus GS guide and feed spindle lathe in very good original condition! Technical specifications: >> Year of manufacture approx. 1992 Machine no. 4549 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle bore 23 mm >> Short taper spindle head DIN 4 >> Tailstock MT 2 >> Feed rates from 0.03 to 0.15 mm/rev >> Possible thread sizes: metric, inch, module, and diametrical pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: Itsdpfx Aewkh Abed Dsp >> New collet chuck system, new collets from 3 to 25 mm >> 1 piece Three-jaw chuck with 2 sets of jaws >> Mulifix size A with 2 tool holders About the machine: Offered is a Weiler Primus GS guide and feed spindle lathe in very good original condition. The machine is fully functional. All slides run very smoothly and evenly. The bed guides are in excellent condition. The Weiler runs very quietly even at high speeds. The Primus was used in a training facility. This newer generation of Weiler lathes is very user-friendly and can produce surfaces that look as if they were ground. Take advantage of the opportunity to view this machine on-site with power on and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus GS lead and feed screw lathe 3 axis digital readout Easson- ES8 from training workshop Super condition !!! Technical data: >> Year of construction approx. 1990 Machine no. 3768 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head DIN 4 Iedpfx Aevkfhpod Detp >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 3-axis digital display from Easson ES8 >> collet chuck device from 1 to 20 mm collets 1 mm rising with holder and draw tube >> 1 three-jaw chuck with 2 sets of jaws >> 1 four-jaw chuck with 2 sets of jaws >> Mulifix size A with 3 steel holders >> Bed stop >> Turning device To the machine : We are offering a Weiler Primus lathe built around 1990 in excellent condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The bed guides are in very good condition. The Weiler runs smoothly even at high speeds. The machine comes from a training workshop of a large company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus LZ/G lead and feed screw lathe in special paint finish light gray !!! Technical data: >> Year of construction ca.1990 Machine-No.3150 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm >> Short taper spindle head DIN 4 >> Tailstock MK 2 Isdjvivmyepfx Ad Djtp >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck NEW 125mm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> collet chuck device new with collets from 3 to 26mm 1 mm increasing new >> To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run smoothly and evenly. The bed guides are in very good condition. The Primus was used in a training company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Weiler Primus VC Precision Centre Lathe 3-axis Digital Readout K&C NEW with VC Drive, Stepless Speed Adjustment, and CE Compliance, Very Good Condition Technical Data: >> Year of manufacture: 2003, Machine No. 646 >> Centre height: 140 mm >> Centre distance: 500 mm >> Spindle speeds: up to 4000 rpm, stepless >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock Morse taper 3 Isdpfsw Idllex Ad Djtp >> Feeds: from 0.02 to 0.63 mm/rev >> Thread types: Metric, Inch, Module, and Diametral Pitch >> Metric thread pitches: from 0.25 to 8 mm >> Weight: approx. 800 kg >> Spindle brake can be activated >> Machine dimensions approx. 1.4 m x 1.55 m x 0.95 m Accessories and Equipment: >> 3-axis Digital Readout K&C NEW >> Collet chuck system with collets from 3 to 26 mm, new, 1 mm increments, NEW >> 160 mm 3-jaw chuck with 2 sets of jaws >> Multifix size A with 2 toolholders >> Electric chip guard >> Machine feet >> Splash guard About the Machine: This offer is for a Weiler Primus VC lead and feed screw lathe, built in 2003 and in very good original condition. A very nice lathe with VC drive and stepless spindle speed control. The digital readout and scales from K&C are new. This newer generation of Weiler lathes is very user-friendly and can produce ground-like surface finishes. The K&C digital readout makes operation even easier and more precise. Take the opportunity to inspect this machine under power on site and be convinced of its condition.