Used measuring & testing equipment for sale (1,398)

Condition: like new (used), Year of construction: 2023, Shimadzu LC-2050C 3D + RF-20AXS – Complete HPLC System – 2023 For sale is a high-end Shimadzu LC-2050C 3D liquid chromatograph, additionally equipped with a Shimadzu RF-20AXS fluorescence detector. Both instruments were manufactured in 2023. The set is unused and in very good cosmetic condition. System Configuration • Shimadzu LC-2050C 3D – Integrated HPLC System • Built-in PDA (Photodiode Array) detector • Shimadzu RF-20AXS – External FLD (Fluorescence Detector) • Integrated autosampler • Sample cooling • Column thermostat • Four-component low-pressure gradient • Integrated touchscreen panel • Dell computer • UPS / Emergency power supply • Accessories and cables as shown in the photos Shimadzu LC-2050C 3D – Key Parameters Pump • Flow rate setting range: 0.0001–10 mL/min • Four-component low-pressure gradient • Gradient setting range: 0–100%, step 0.1% • Maximum pressure: • 50 MPa at flow rates of 0.0001–3 mL/min • 44 MPa at flow rates of 3.0001–5 mL/min • 22 MPa at flow rates of 5.0001–10 mL/min • Integrated mobile phase degassing system Autosampler • Automatic sample injector • Sample injection volume range (standard configuration): 0.1–100 µL • Sample injection volume accuracy: ±1% at 50 µL • Sample cooling/thermostating capability • Sample cooling temperature range: 4–45°C PDA Detector The LC-2050C 3D version features an integrated PDA (Photodiode Array) detector, enabling spectral recording and analysis of multiple wavelengths. Thanks to the PDA detector, the system allows not only for standard chromatographic analysis but also for spectral evaluation of detected substances. Shimadzu RF-20AXS Fluorescence Detector The system has been additionally equipped with a high-sensitivity RF-20AXS fluorescence detector, significantly increasing the analytical capabilities of the entire set. RF-20AXS Parameters • Light source: Xenon lamp • Additional low-pressure mercury lamp for wavelength accuracy control • Wavelength range: 200–750 nm • Spectral bandwidth: 20 nm • Wavelength accuracy: ±2 nm • Wavelength repeatability: ±0.2 nm • S/N for the Raman peak of water: ≥2000 • Standard flow cell: 12 µL • Maximum cell pressure: 2 MPa • Cell thermostat • Ability to monitor two pairs of excitation/emission wavelengths simultaneously The combination of PDA + FLD (Fluorescence Detector) provides a wide range of analytical capabilities and allows for the determination of both standard UV/Vis absorbing compounds and substances requiring highly sensitive fluorescence detection. Device Data Shimadzu LC-2050C 3D • CAT. NO.: 228-65822-58 • Year of manufacture: 2023 Shimadzu RF-20AXS • CAT. NO.: 228-65305-58 • Year of manufacture: 2023 Application Njdjzv Salspfx Adqolf The system is intended for, among others: • Pharmaceutical laboratories • Quality control • Chemical laboratories • Food industry • Environmental research • Research and development laboratories • HPLC analyses requiring PDA detection • Trace analyses using fluorescence detection Condition Year of manufacture: 2023 Device is unused. Very good cosmetic condition – consistent with the photos. Sale of a complete set: Shimadzu LC-2050C 3D + RF-20AXS + Dell computer + UPS + accessories shown in the photos. Additional photos, serial numbers, and information about the device can be provided upon request.

Condition: used, Technical details: traction force: 250 kN control: SCHENCK HYDROPULS PSB dayligth: 1000 - 1200 je nach Spannwerkzeug /acc. clamp.tool mm piston stroke: 180mm mm A servo-hydraulic leaf spring testing machine with Series 65 digital electronics is designed for testing leaf springs used in commercial vehicles, railway vehicles, and industrial applications. Nlodezi R R Ajpfx Adqof A hydraulic actuator applies defined loads while force, displacement, and, if required, strain are measured. Typical tests: ·Static spring characteristic (force-displacement curve) ·Fatigue and endurance testing ·Cyclic load testing ·Service life testing ·Tensile and compression testing ·Production quality control *

Year of construction: 1992, condition: used, Technical details: x-axis: 150 mm z-axis: 400 mm diameter: 420 mm air pressure - required: 6 bar tool diameter: 420 mm total power requirement: 0,5 kW weight of the machine ca.: 290 Kg space requirement approx.:: 2,0 x 1,5 x 2,0 m Tool Holders Included: SK50 Tool Holders SK40 Tool Holders VDI50 Tool Holders The ZOLLER V420 is a high-precision tool presetting and measuring machine designed for the accurate measurement and presetting of cutting tools used on CNC milling machines, machining centers, and CNC lathes. Nsdezbrtdspfx Adqslf By measuring tools outside the machine, setup times are significantly reduced, machine productivity is increased, and machining accuracy is improved. Main Applications ·Tool length measurement ·Tool diameter measurement ·Radius measurement ·Cutting edge position measurement ·Tool angle measurement ·Runout inspection ·Measurement of milling, drilling, and turning tools Advantages ·Reduced machine downtime ·Faster setup procedures ·Increased productivity ·Improved machining accuracy ·Reduced scrap and setup errors ·Reliable transfer of tool data to CNC machines Typical Features ·High-precision optical measuring system ·Digital measurement display ·Tool holder interface for various systems (SK, BT, HSK, etc.) ·Data transfer to CNC controls ·Tool data management ·High repeatability and accuracy Typical Areas of Use ·Tool rooms ·CNC machining centers ·Manufacturing facilities ·Precision engineering ·Quality control departments *

Condition: excellent (used), The device performed only 140 measurements. NITON XL3t 980 GOLDD+ – a portable X-ray analyzer with a next-generation SDD detector featuring GOLDD technology. GOLDD technology enables significant improvements in accuracy and measurement time. This detector is 10 times faster than a conventional PIN detector and up to 3 times more accurate than a conventional SDD detector. The NITON XL3t 980 GOLDD+ analyzer achieves a unique combination of a 50kV X-ray tube with optimized measurement geometry and a patented processor and software. It allows for fast and accurate, simultaneous analysis of up to 28 elements: Mg, Al, Si, P, S, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Se, Zr, Nb, Mo, Hf, Ta, W, Re, Pb, Bi, Ag, Pd, Sn, Sb. Additionally, the analyzer enables the analysis of precious metals: Au, Pt, Ir, Ru, Rh. Analysis of light elements such as Mg, Al, Si, P without the use of helium is possible thanks to a special set of filters and a highly sensitive detector. Without helium, the determination of light elements is possible for concentrations above 0.x%. A large library of spectral databases for alloys enables the identification of stainless steels, tool steels, chromium-molybdenum steels, and alloys based on nickel, cobalt alloys, copper-based alloys, titanium alloys, and zinc, zirconium, and aluminum alloys. The analyzer provides very fast measurement. The analysis time for typical alloys is less than 3 seconds. An additional library for the analysis of light elements in the helium mode allows for the segregation and sorting of aluminum alloys such as: cast alloys depending on the silicon (Si) or magnesium (Mg) content, aluminum (Al), silicon (Si), and phosphorus (P) content in bronzes, aluminum (Al) content in titanium alloys, magnesium alloys (Mg), zinc alloys with aluminum (Al). The analyzer enables the analysis of: all iron-based alloys (0.00x% – 100%) and non-ferrous metal-based alloys (0.00x% – 100%) and rare metals Hf, Ta, Re (0.00x – 100%) precious metal alloys Au, Ag, Pd, Pt, Ir (0.00x%-100%). The NITON XL3t 980 GOLDD+ analyzer operates based on BASIC PARAMETERS, meaning that it calculates the percentage content of elements based on a mathematical equation. The analyzer also allows for the development of its own analytical programs: an identification program that assigns a name, symbol, number, etc., to a known sample, and such samples will be identified by that name. a program for quantitative chemical analysis (SuperChem Teach Mode) – based on its own standards, we create our own calibration curves for quantitative analysis. The analyzer has a large, user-friendly, touch-screen display. The screen is color and tiltable, which facilitates reading the results during field work. It includes an integrated scanner and backlit alphanumeric sample identification codes. The software allows you to store up to 10,000 results in the analyzer's memory or transfer them to a computer. Connecting the device to a computer and controlling its operation via a computer is possible using a traditional cable or wirelessly via Bluetooth. It is supplied with two interchangeable batteries. One battery enables continuous operation for 8-10 hours without the need to recharge. It has two libraries, 900 and 800. Nsdpfx Aozlcciedqelf

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: 200008301032, measuring range X-axis: 400 mm, measuring range Y-axis: 500 mm, measuring range Z-axis: 350 mm, table width: 680 mm, table length: 855 mm, No minimum price – guaranteed sale to the highest bidder! Submitting a bid obligates you to collect the item on time between October 7, 2026, and October 14, 2026! TECHNICAL DETAILS Measuring range, X-axis: 400 mm Measuring range, Y-axis: 500 mm Measuring range, Z-axis: 350 mm Maximum workpiece weight: 280 kg Table width: 680 mm Table length: 855 mm MACHINE DETAILS Nlsdpfx Aozu Ixuodqof Dimensions & Weight Dimensions (L x W x H): 2,000 x 1,100 x 1,100 mm Total weight: 500 kg

Condition: like new (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: ZEISS Comet®LƎD 8M, workpiece weight (max.): 5,000 kg, workpiece length (max.): 1,000 mm, workpiece height (max.): 1,000 mm, workpiece width (max.): 1,000 mm, ZEISS Comet®LƎD 8M Nsdpfx Adszwk Nbeqslf

Condition: like new (used), Year of construction: 2021, functionality: fully functional, We are selling our Keyence XM because we are acquiring a larger machine. The device has been used regularly, but it is too small for our applications, so it is practically like new and in perfect condition. Nedpfx Adjzfik Hsqjlf The device is fully equipped and comes with an extension and a tripod.

Condition: excellent (used), Year of construction: 2012, Coordinate measuring machine for inline and prduction use from Mitutoyo in good condition, built 2012, installed 2014 Controller Mitutoyo UC240, Probe Renishaw PH10MQ/TP7, Software Mitutoyo MCOSMOS-1 V3.5 Measuring ranges: X – axis 905 mm Y – axis 1005 mm Njdpfxoh Nu Uhj Adqelf Z – axis 605 mm Accuracy acc. ISO 10360 MPEE = [2,5 + 3,5L/1000] µm at temperature range 18… 22 °C Base material Steel fixing holes M8 x 1,25 Scales Mitutoyo Linear Scales Scale Resolution 0,0001 mm DC motores with encoders Guideways linear guides Probe Renishaw PH10MQ with PHC10-2 plus (used) Probe Renishaw TP7 optional with ACR-3 (used) Computer Workstation WIN 10 (used) loading and tranport to be arranged by the customer

Year of construction: 2026, operating hours: 1 h, condition: new, machine/vehicle number: H10TM, Universal testing machine H10TM Force: 10 kN Crosshead travel: 700 mm Installation space: 400 mm Overall height: 1230 mm Weight: approx. 84 kg Stroke resolution: 0.01 mm Testing speed: 1-500 mm/min Return speed: 700 mm/min Nlodpfx Aszuma Rodqsf Force sensor: 10 kN Including evaluation electronics and basic software. Our testing machines can be operated in stand-alone mode using a numeric keypad, allowing for a “quick test” even without a PC. For tests that require data storage and recording of the curve profile, we offer you the option to control and evaluate the test using the basic software. This allows you to generate various test sequences and create a test report. Furthermore, you have the option to process the raw data in your own programs. Optional: - Delivery & commissioning - DAkkS or factory calibration according to DIN EN ISO 7500-1 Load cells: 5N-10N-20N-50N-100N-200N-500N-1kN-2kN-3kN-5kN-10kN - Grips: Compression platens, bending fixtures, shear fixtures, wedge grips, scissor grips, screw grips, pneumatic grips, and hydraulic grips.

Condition: used, MDR 2000 Moving Die Rheometer • Closed, bic conical chamber system • Fast microprocessor for temperature control • Torque measurement via friction-free torque transducer • High precision, high efficiency Nljdpfx Adjzul Dbeqjf • Automation option for maximum productivity State-of-the-art vulcanization technology The MDR 2000 Moving Die Rheometer from Alpha Technologies has become the global standard for vulcanization technology. Two directly heated, bic conical tool halves with low mass provide fast and accurate temperature recovery. The oscillating lower tool half eliminates the need for a rotor, as in the Oscillating Disk Rheometer (ODR 2000). This results in faster temperature recovery and greater data accuracy. The resulting torque is measured by a torque transducer in the upper tool half, ensuring that friction forces from bearings and seals no longer affect the torque measurement. The torque signal is calibrated using a torsion spring rod with known values. This ensures long-term accuracy, repeatability, and reproducibility of the data. The unique closed chamber system enables above-average reproducibility and sensitivity to variations in the compound. Fast-responding temperature control is ensured by an optimized system. These properties, combined with a highly sensitive torque transducer and state-of-the-art microprocessor technology, offer the best in networking technology.

Condition: used, Year of construction: 2016, functionality: fully functional, measuring range X-axis: 300 mm, measuring range Y-axis: 200 mm, measuring range Z-axis: 200 mm, workpiece weight (max.): 16 kg, total height: 1,700 mm, type of input current: AC, total width: 900 mm, total length: 1,050 mm, overall weight: 321 kg, input voltage: 230 V, table load: 16 kg, maximum load weight: 16 kg, Equipment: type plate available, We are offering this used Hexagon OPTIV CLASSIC 322 coordinate measuring machine, manufactured in 2016, for sale. Manufacturer: Hexagon Model: OPTIV CLASSIC 322 Year of manufacture: 2016 Condition: used Njdpfjzvdlyjx Adqslf Type: Coordinate measuring machine A computer can be purchased with the machine if required. The price does not include a computer. The PC DMIS version is unknown and must be checked by the buyer to determine if and how the software can continue to be used. With prior arrangement, the machine can be started up and a sample part measured. If you have any questions or require further information, please send us a message or call us.

Condition: used, LDS V455 Vibration Testing System / Shaking Testing System Manufacturer: Ling Dynamic Systems Ltd. (LDS) Nljdozulngjpfx Adqof Shaker: V455 Machine Type: Electro-dynamic Vibration / Shaking Testing System Power Amplifier: LDS PA 1000 Power Amplifier For sale is a used vibration and shaking testing system from Ling Dynamic Systems Ltd. (LDS). The system consists of an electro-dynamic LDS V455 shaker, a PA 1000 power amplifier, and a separate fan/cooling unit. The system is suitable for generating defined mechanical vibrations, as well as for vibration, stress, and component testing. Possible applications include use in laboratories, development, quality assurance, and industrial testing. Technical data: Manufacturer: Ling Dynamic Systems Ltd. (LDS) Shaker: V455 System: Electro-dynamic Vibration / Shaking Testing System Power Amplifier: LDS PA 1000 Power Amplifier Amplifier Output Current Indicator: 0–20 A RMS Year of Manufacture: Not specified Fan Motor: Manufacturer: ASEA / Electrolux Elmotor A/S Type: M056SX2 Voltage: 220–240 V Current: 2.0 A Speed: 2,880 RPM Protection Class: IP54 Insulation Class: B Capacitor: 1.5 µF / 360 V Country of Manufacture: Denmark Fan: Manufacturer: Air Control Installations (Chard) Ltd. Type: 2M53 Voltage: 240 V Phase: 1 Frequency: 50 Hz Current Draw: 0.45 A Speed: 2,880 RPM Capacitor: 1.5 µF MFD: 440 VAC/WKG: 25 Made in U.K. Dimensions: The overall dimensions of the system cannot be clearly determined from the available images and nameplates. Equipment: LDS V455 electro-dynamic shaker LDS PA 1000 power amplifier Separate fan/cooling unit Shaker mounting / base frame Hoses and connection cables Transport case for the power amplifier Accessories as shown in the images Shipping data: Total weight: 240 kg Condition: Used Signs of wear and tear due to age and use are present. Dirt, paint chips, and traces of corrosion are visible. Optical condition as shown in the images. Scope of supply: 1 × LDS V455 electro-dynamic shaker 1 × LDS PA 1000 power amplifier 1 × Fan/cooling unit Shaker mounting / base frame Connection cables and hoses as shown in the images Transport case for the power amplifier Accessories as shown in the images Availability: by arrangement. Scope of supply as shown in the images. Subject to changes, errors and prior sale.

Condition: used, Year of construction: 2006, X-axis: 1600mm, y-axis: 1800mm, z-axis: 1000mm, max. workpiece weight: 3.5t, noise level: less than 70dBA, compressed air connection: 6-8bar, connected load: 2500VA, control: CALYPSO 7.6.08 software, length: 2940mm, width: 2450mm, height: 3800mm, weight: 8.5t, operating hours: 38,996h, with documentation. An on-site inspection is possible. Njdpfezuz Aaex Adqelf

Condition: good (used), Hardness tester, fully functional Upon request, transport and loading can be organized throughout Europe at an additional cost. Prices are exclusive of VAT. Nledpfx Ajzvfd Rjdqof Inspection possible by appointment. Please contact us – our team will be happy to assist you. Machine purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINERY, MACHINE TOOLS, AND MORE. Are you looking for a high-quality yet affordable machine for your production? Or do you wish to sell your equipment? For further information or contact options, please reach out via the contact form.

Year of construction: 2026, condition: new, functionality: fully functional, Universal testing machine PM10 (10 kN) – Complete system including software For sale is a versatile universal testing machine PM10 with a maximum testing force of 10 kN. The system is characterized by its flexibility and efficient stand-alone operation. The machine is ready for use, including evaluation electronics and basic software for comprehensive data analysis. Technical data & performance features • Maximum testing force: 10 kN (including matching load cell) • Crosshead travel: 700 mm • Testing space / installation space: 400 mm • Testing speed: 1 – 500 mm/min • Return speed: 700 mm/min • Path resolution: 0.01 mm • Overall height: 1,230 mm • Weight: approx. 85 kg Highlights & operation • Flexible stand-alone operation: Quick tests can be performed directly on the machine via a numeric keypad, completely without a PC. • Powerful basic software: Machine control, recording of curves, and detailed data storage when connected to a PC. • Open data interface: Easy export of raw data for further processing in your own programs (e.g., Excel). Scope of supply • Universal testing machine PM10 • Load cell 10 kN • Integrated evaluation electronics • Basic software for control and evaluation Nlodpoyc U Ugefx Adqjf Optional services & accessories (upon request) • Service: Delivery, professional installation, and commissioning on site • Certification: DAkkS or factory calibration according to DIN EN ISO 7500-1 • Extensive range of clamping devices: Pressure plates, bending and shear devices, wedge and scissor clamps, peeling and screw clamps, as well as pneumatic or hydraulic clamping devices. The machine is available immediately. Please contact us for an individual offer including the appropriate accessories for your testing requirements!

Year of construction: 2026, condition: as good as new (ex-display), Universal Testing Machine PM10 Force: 10 kN Crosshead travel: 700 mm Installation space: 400 mm Overall height: 1230 mm Weight: approx. 85 kg Resolution: 0.01 mm Testing speed: 1-500 mm/min Njdpfxsd R Dpms Adqolf Return speed: 700 mm/min Load cell: 10 kN Includes evaluation electronics and basic software. Our testing machines can be operated in stand-alone mode via a numeric keypad, allowing for a “quick test” even without a PC. For tests that require data storage and recording of the curve profile, we offer the option of control and evaluation with the basic software. This allows you to generate different test sequences and create a test report. Furthermore, you have the option to process the raw data in your own programs. Optional: - Delivery and commissioning - DAkkS or factory calibration according to DIN EN ISO 7500-1 - Clamping devices: Pressure plates, bending fixtures, shear fixtures, wedge clamps, scissor clamps, peeling clamps, screw clamps, pneumatic clamps, and hydraulic clamps.

Year of construction: 2026, condition: as good as new (ex-display), Universal Testing Machine PM5 Force: 5 kN Traverse Travel: 520 mm Working Depth: 66 mm Overall Height: 1036 mm Nlsdpfx Aeydanhodqjf Weight: approx. 48 kg Position Resolution: 0.01 mm Test Speed: 1–500 mm/min Return Speed: 700 mm/min Load Cell: 5 kN Incl. evaluation electronics and basic software. Our testing machines can be operated in stand-alone mode via a numeric keypad, enabling “quick tests” without the need for a PC. For testing procedures requiring data storage and curve recording, our basic software provides both control and evaluation functions. This allows you to generate different test sequences and create a test report. In addition, raw data can be further processed in your own software. Optional: - Delivery & commissioning - DAkkS or factory calibration according to DIN EN ISO 7500-1 - Grips and fixtures: Compression plates, bending fixtures, shear devices, wedge grips, scissor grips, peeling grips, screw grips, pneumatic grips, and hydraulic grips.

Year of construction: 2026, condition: as good as new (ex-display), Universal testing machine PM5 Force: 5 kN Crosshead travel: 520 mm Working space depth: 66 mm Overall height: 1036 mm Weight: approx. 48 kg Resolution: 0.01 mm Testing speed: 1-500 mm/min Nsdpfxed R Dqbo Adqelf Return speed: 700 mm/min Force sensor: 5 kN Includes evaluation electronics and basic software. Our testing machines can be operated in stand-alone mode via a numeric keypad, allowing for a "quick test" even without a PC. For tests that require data storage and recording of the curve, we offer the option to control and evaluate the test using the basic software. This allows you to generate various test sequences and create a test report. Furthermore, you have the option to process the raw data in your own programs. Optional: - Delivery and commissioning - DAkkS or manufacturer calibration according to DIN EN ISO 7500-1 - Clamping devices: Pressure plates, bending jigs, shear jigs, wedge clamps, scissor clamps, peeling clamps, screw clamps, pneumatic clamps, and hydraulic clamps.

Year of construction: 2026, condition: as good as new (ex-display), Universal Testing Machine PM3 Force: 3 kN Nedpfx Aod R Dpujdqjlf Crosshead travel: 520 mm Working space depth: 66 mm Overall height: 1036 mm Weight: approx. 40 kg Resolution: 0.01 mm Testing speed: 1-500 mm/min Return speed: 700 mm/min Force sensor: 3 kN Includes evaluation electronics and basic software. Our testing machines can be operated in stand-alone mode using a keypad, allowing for a “quick test” even without a PC. For tests that require data storage and a record of the curve profile, we offer you the option to control and evaluate the test using the basic software. This allows you to generate various test sequences and create a test report. Furthermore, you have the option to process the raw data in your own programs. Optional: - Delivery and commissioning - DAkkS or factory calibration according to DIN EN ISO 7500-1 - Clamping devices: Pressure plates, bending fixtures, shear fixtures, wedge clamps, scissor clamps, peeling clamps, screw clamps, pneumatic clamps, and hydraulic clamps.

Condition: used, Year of construction: 2020, functionality: fully functional, Equipment: type plate available, Magnetic inductive flow meter for liquids, with 2 DN 50 connections Nedpfxsythu Us Adqslf

Condition: used, Reading type / 0 Nlsdpey Sur Esfx Adqof weight - pallet system / kg length / mm

Condition: used, LS 704 C - glass scale with reading head Nlsdpsylcwhsfx Adqjf Length: ML 720mm HEIDENHAIN LS 704 C ID 23713415 SN: 4521917K

Condition: used, HEIDENHAIN LS 688C 1840mm - glass scale Njdpfxjylcxfj Adqjlf S.No. 25712659B

Condition: used, HEIDENHAIN LS 603 - glass scale with reading head AE LS 603 ID no. 22852952 Njdpjylcypofx Adqslf S.No. 1834382

Condition: used, HEIDENHAIN LB 302 - glass scale Nlodpfx Aey Sulrodqof Total = 1x LB 302 4640mm 2x LB 302 ML 2000mm 2x LB 302 ML 320mm