Used Oliver Fritz Gmbh & Co. Kg Abrasive Preparation Bucket Elevator for sale (101,651)

Condition: excellent (used), Year of construction: 2015, operating hours: 20,331 h, functionality: fully functional, pressing force: 100 t, filling opening width: 970 mm, filling opening length: 1,800 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, overall weight: 33,000 kg, Good day, We hereby offer you, without obligation, a used, complete baling press line consisting of a baler manufactured by HSM, type VK 8818 R-FU, including conveyor technology and wire tying stations. The following technical data was taken from the manufacturer's operating manual and brochures, for which we cannot guarantee accuracy or completeness. Technical Data – Baler: Manufacturer: HSM GmbH + Co. KG, Germany Type: VK 8818 R-FU Year of manufacture: 2015 Operating hours: 20,331 hours (as of September 2025) Number of bales pressed: 29,020 bales (as of September 2025) Press force (main press): 1000 kN Specific pressing force: 120 N/cm² Shear edge ejector force: 121 kN Feed opening dimensions: 970 x 1,800 mm Theoretical cycle time (idle): 8.3 seconds Theoretical output capacity: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length adjustable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency-controlled Connected load: 110 kW Total current consumption: 213 A Fusing: 250 A slow-blow Tying: 5-fold horizontal, fully automatic Output at bulk density: 20 kg/m³: 12.86 t/hour 50 kg/m³: 32.15 t/hour Bale weights (approx. 1.2 m bale length): 650 up to 750 kg per bale, material-dependent Hydraulic oil tank volume: 2000 L HVI 46 PLC control system: Siemens S7-300 Isdsyz Af Eepfx Abbotf Control panel: Siemens TP 700 Baler dimensions (assembled): 12,130 x 4,800 x 3,270 mm (L x W x H) Space requirement (with conveyor): 35,000 x 8,480 x 7,745 mm (L x W x H) Baler weight: approx. 33 t (main press approx. 12 t, press channel with bale clamp approx. 10 t) Additional Optional Equipment Ordered: – Frequency-controlled main drive, 2 x 45 kW, with up to 40% energy savings compared to the standard 2 x 45 kW drive, with same performance – Manual activation/deactivation of the number of wire bindings to save tying wire on non-expansive material – Shear edge ejector with 121 kN pressing force – Sensor-based wire monitoring, with baler shut-off in case of wire breakage or wire end – Bale chute – Optical warning signal, mounted on the control cabinet Condition of the Baler: The complete baling system (baler and conveyor technology) is in good, ready-to-use condition. The unit has been cleaned weekly, lubricated, and maintained according to manufacturer specifications by the operator. Technical Data – Chain Belt Conveyor: Manufacturer: Stadler Anlagenbau GmbH Type: Chain Belt Conveyor KF 1800 Year of manufacture: 2015 Belt speed: 0.36 m/second Feeder belt length: 7,000 mm Inclined belt length: 14,500 mm Gooseneck length: 1,550 mm Incline: 30° Nominal width: 1,800 mm Usable width: 1,638 mm Overall conveyor height: 7,745 mm Pit dimensions for conveyor: 11,200 x 3,000 x 1,250 mm (L x W x H) Scope of Delivery: – HSM VK 8818 R-FU baler – Maintenance platform – Bale chute – Wire diverting stations – Wire spool trolleys (without wire spools) – Stadler KF 1800 chain belt conveyor – Transverse sliding belt conveyor – Pit cover from feed conveyor to pit – Second control cabinet to operate the baler from the conveyor – Machine documentation in English Delivery Time: The complete system has already been dismantled, placed into storage, and can be loaded at short notice following receipt of payment. We would be pleased if this or one of our other balers might be of interest to you. Your Service Team Mertens & Frowein GmbH

Year of construction: 2015, condition: good (used), functionality: fully functional, machine/vehicle number: A-150016, AUTOMATED ADHESIVE APPLICATION MACHINE, GANTRY SYSTEMS, AND AUTOMATED METAL INSERT PLACEMENT UNIT This system is part of a larger production line; please refer to our other listings for more information. The offered system includes 3 provision stations for facing sheets, an automated adhesive application machine for sandwich panel bonding, a lay-up conveyor for manual assembly of the inlay/ribbing, gantry systems for manipulating the facing sheets, and an automated placement unit for metal inserts/reinforcement points. COMPONENT DIMENSIONS (from previous production): L/W min: 2000mm x 1500mm L/W max: 8000mm x 2500mm H min: 12mm H max: 60mm MATERIALS (from previous production): GRP, sheet metal, plywood, wood/PU strips, PVC, Styrofoam GLUING GANTRY FOR CONTOUR & SURFACE BONDING (of the facing sheets & inlays): Number of needle valves surface: 104 Number of needle valves contour: 1 Iedpfxjyt Nm Ss Abbjtf Adhesive system: 1K-PUR Number of nozzles in water spray unit: 8 AUXILIARY UNITS: Climate chamber (storage for 1K-PUR adhesive) Vacuum pump for gantry systems Punching unit

Condition: good (used), Year of construction: 2005, operating hours: 15,606 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,050 mm, filling opening length: 1,250 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 700 mm, bale weight: 500 kg, power: 30 kW (40.79 HP), volume flow: 160 m³/h, Good day, We hereby offer you, without obligation, a used baler manufactured by Presto GmbH & Co. KG, model HPK 50 B. The following technical data have been taken from the manufacturer's operating manual and brochures, for which we assume no liability for accuracy or completeness. Manufacturer: Presto GmbH & Co. KG Model: HPK 50 B Year of manufacture: 2005 Operating hours: 15,606 hours Main press force: 50 t Drive power: 30 kW Total connected load: 31.5 kW Rated current: 64 A Throughput under operating conditions at a bulk density of 60 kg/cbm: approx. 6.7 t/hour Machine weight (press): 12.5 t Note: The machine has been repaired in our workshop (the main control valve on the hydraulic block was replaced) and tested during ongoing operation in both manual and automatic modes. Machine documentation is available in German. Viewing of the press can be arranged by appointment in our workshop. We would be pleased if this machine is of interest to you. Itedpfxeyplwfe Abbef Your service team at Mertens & Frowein GmbH

Condition: used, Year of construction: 1991, consisting of: -SIGMATHERM plate heat exchanger (heat exchange surface 21.5 m2) - Forerun tank 1200 l - Hilge product pump with manual control valve - Hilge hot water circulation pump - 500 l expansion tank - Shell-and-tube heat exchanger - Compressed air reduction station -Control cabinet with operating panel Additional title: juice heating plant for pasteurization Capacity: 100 hl/h Perm. working overpressure: 16 bar test pressure 20,8 bar Wärmeaustauschfläche: 21 m2 Length: 5,6 m Width: 2 m Height: 2,4 m Operation / Control: Control cabinet with operating buttons Material: Stainless steel Base construction: Frame Iodpfjvcqy Uex Abbetf Features: 2 x vessels; plate heat exchanger; pipe heat exchanger; 2 x product pumps; process measuring and control technology. various valves and other fittings

Condition: excellent (used), Year of construction: 2017, operating hours: 150,050 h, functionality: fully functional, controller manufacturer: Heidenhain, controller model: iTNC530, rotary table diameter: 500 mm, overall weight: 13,000 kg, spindle speed (max.): 14,000 rpm, operating hours of spindle: 6,950 h, coolant supply: 20 bar, spindle nose: HSK 63, number of slots in tool magazine: 60, Equipment: chip conveyor, oil mist separator, rotational speed infinitely variable, • Condition: Excellent condition • Operating hours: 6,950 • KESSLER rotary table, Ø 500 mm • Tool magazine: 60 stations, HSK-A63 Itedpfx Absx Hg Ibsbof • Internal coolant supply: 20 bar, with band filter system • Coolant system: Automatic coolant level monitoring • Air through spindle • Tool measurement: BLUM laser tool measuring system • Workpiece measurement: Infrared workpiece probing (3D touch probe system), incl. workpiece measurement preparation • Collision monitoring: POS DCM module • Media feed: 3-channel media feed in the center of the table • Viewing: Rotary inspection window • Handwheel Please send us an inquiry directly via our website if you are interested in the machine. Due to technical reasons, direct inquiries for a quotation via third-party platforms are difficult and may be delayed.

Condition: good (used), Year of construction: 2011, operating hours: 40,000 h, functionality: fully functional, pressing force: 88 t, filling opening width: 990 mm, filling opening length: 1,800 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, overall weight: 23,000 kg, oil tank capacity: 2,000 l, power: 90 kW (122.37 HP), volume flow: 643 m³/h, Good day, We hereby offer, subject to prior sale, a used baler including conveyor belt, wire tying stations, and bale chute from the manufacturer HSM GmbH + Co. KG, model VK 8818 FU. The following technical specifications were taken from the manufacturer's operating manual and brochures; we do not assume any liability for the correctness or completeness of this information. Manufacturer: HSM GmbH + Co. KG, Germany Model: VK 8818 FU Year of manufacture: 2011 Operating hours: approx. 40,000 hours as of July 2025 Main press force: 880 kN Specific press force: 107 N/cm² Feed opening dimensions: 990 x 1,800 mm Theoretical throughput: 643 m³/hour Bale dimensions: 1,100 x 750 mm, length adjustable from 600 up to 2,000 mm Drive power: 2 x 45 kW, frequency-controlled Tying: 5-fold horizontal, fully automatic Baler dimensions (set up): 12,130 x 4,800 x 3,270 mm (L x W x H) Overall installation dimensions with conveyor system: 14,000 x 23,000 x 7,745 mm (L x W x H) Isdpfx Aboymmtcjbjtf Note: The machine was used in a recycling facility for compacting paper, cardboard, and film. The press is in good condition and will be replaced with a new, larger press in May/June 2026. Until then, the machine can be inspected in operation with material. We would be pleased if this baler is of interest to you. Your Mertens & Frowein GmbH service team

Condition: used, Year of construction: 2000, machine/vehicle number: P18096N, functionality: fully functional, pressing force: 20 t, stroke length: 160 mm, total height: 2,150 mm, overall weight: 180 kg, Good day, We hereby offer you, without obligation, a used workshop press from Rodcraft, model WP 20F. Manufacturer: Rodcraft Pneumatic Tools GmbH & Co. KG Model: WP 20 F Year of manufacture: 2000 Machine No.: P18096N Hydraulic stroke: 160 mm Pressing force: 20 t Machine dimensions: 2150 x 960 x 660 mm Transport dimensions: 2150 x 980 x 750 mm Machine weight: 180 kg Note: The above technical data has been taken from the manufacturer’s brochures or other sources, for which we cannot guarantee the accuracy or completeness. Scope of delivery: Itedpfx Aoygm N Djbbjf 1 unit used workshop press Rodcraft, type WP 20F Application area and condition: The machine was occasionally used in an industrial metalworking shop for pressing out bearings, etc. The machine is fully functional and in good condition. We would be pleased if this machine is of interest to you. Your service team at Mertens & Frowein GmbH

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, power: 9.7 kW (13.19 HP), Technical data cardboard shredder: Manufacturer Presto GmbH & Co. KG Type PZA Year of construction 2007 Throughput volume 130 m³/hour Speed 37/9 rpm Motor power 7,5 / 2,2 kW Electrical connection 32 A Dimensions shredder inside 1,490 x 1,320 x 530 mm (L x W x H) Dimensions shredder outside without cover 2,308 x 1,320 x 685 mm (l x w x h) Machine weight 0,45 tons Use of the systems: The PZA cardboard shredder was in use in a Dutch logistics centre to pre-shred loose, erected cardboard boxes from the returns department and then press them into bales. The cartons were fed manually onto the infeed conveyor and transported directly to the cardboard shredder by a sliding belt conveyor and shredded. The pre-shredded cardboard boxes were then transported over hundreds of metres to the baler where they were pressed. Scope of delivery: 1 piece Presto cardboard shredder (2-shaft shredder) type PZA Itjdpsu Tha Ijfx Abbof Comments: The cardboard shredder was an elementary part of the disposal line and therefore good maintained to ensure high availability of the returns department. The machine is in good condition and ready for immediate use. The price is per piece exw. our warehouse in Siddeburen, the Netherlands. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2010, operating hours: 3,641 h, functionality: fully functional, pressing force: 36 t, filling opening width: 1,100 mm, filling opening length: 1,080 mm, bale width: 1,100 mm, bale height: 750 mm, power: 15 kW (20.39 HP), volume flow: 90 m³/h, Technical data baler: Manufacturer Presto GmbH & Co. KG Typ CC 36 M Year of construction 2010 Hours of operation 3,641 h Press power main press 36 t Specific press capacity 467 N/cm² Feed channel 1.080 x 1100 mm (l x w) Cycle time 34 sec. Capacity per cycle time 0,85 m³ Theoretic throughput rate 90 m³/h Throughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale size 1100 x 750 mm (w x h), length variable Driving motor 15 kW Tying 4-fold vertical, semi-automatic, with polyester synthetic yarn Throughput rate at a bulk weight of 35 kg/cbm 1,8 to/h bulk weight of 60 kg/cbm 2,5 to/h Iedpsu Thh Eefx Abbetf bulk weight of 100 kg/cbm 3,1 to/h Transport dimensions only baler 4.200 x 1.640 x 2.200 mm Machine weight baler approx. 4 to Comments: The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating instructions, CE, electrical and hydraulic circuit diagram) is available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2003, condition: good (used), functionality: fully functional, machine/vehicle number: 03234, 6 Brush ( 3 pairs) descaling machine for steel wire size 5.5mm - 16.0 mm max (low carbon) Brush pairs arranged in a 60 degree offset for maximum effect. A very clean looking machine. On site viewing and inspection recommended Iedpfx Ajx R Uzdjbbotf

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Itsdpfx Aox A U Ncjbbof Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: reconditioned (used), Year of construction: 2014, operating hours: 5,612 h, functionality: fully functional, pressing force: 48 t, filling opening width: 1,020 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 550 kg, total height: 2,800 mm, overall weight: 12,000 kg, transport height: 2,800 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), volume flow: 332 m³/h, Technical information baler: Manufacturer HSM GmbH + Co. KG Typ VK 4812 Year of construction 2014 Hours of operation 5,612 hours, stand August 2025 Press power main press 48 tons Specific press capacity 58,2 N/cm² Feed channel 1,250 x 1,020 mm Theoretic cycle time 11.2 sec. Theoretic throughput rate 332 m³/hour Bale size 1,100 x 750 x 600 up to 1,200 mm Driving motor 30 kW Connected load 32 kW Rated current 59 A Tying system 4-fold horizontal, fully automatic Throughput rate at a bulk weight of 20 kg/cbm up to 6 tons/hour bulk weight of 50 kg/cbm up to 13 tons/hour Bale weight up to 550 kg, depends on material SPS controller Siemens SIMATIC S7-200 Operating panel Siemens HMI Touch Panel Filling quantity hydraulic oil tank 300 L Oil type HVI 46 Machine installation dimensions with bale chute 10,046 x 4,387 x 2,705 mm (l x w x h) Transport dimensions baler 8,500 x 2,500 x 2,750 mm (l x w x h) Machine weight press approx. 12 t Scope of delivery: Baler HSM VK 4812, without hydraulic oil, without conveyor system. Two wire reel boxes for 8 pieces 40 kg wire reels, without wire Bale chute Machine documentation in German Comments: The press is equipped with an oil cooler and potential-free contacts for external control. The control cabinet is operated from the left in the direction of pressing, the needle unit is located on the right-hand side and can be folded back for transport. The press was partially overhauled and tested in our workshop, see photos and our function video. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Viewing is possible by appointment. We accept no liability for the technical details or any errors. Isdpfx Absvtpq Hsbotf

Condition: used, Year of construction: 2018, functionality: fully functional, volume flow: 10.2 m³/h, input voltage: 230 V, USED VACUUM PUMP Technical data Iodpfew Rqx Dsx Abbjtf Max. pumping speed 50 Hz (mbar) 8.9 m3/h Max. pumping speed 60 Hz (cfm) 6.0 cfm Ultimate vacuum 2 x 10-3 mbar / 1.5 x 10-3 torr Ultimate vacumm with gas ballast 1 x 10-2 mbar / 0.75 x 10-2 torr Ultimate partial vacuum without gas ballast 4 x 10-4 mbar / 3 x 10-4 torr Water vapor tolerance 40 mbar / 30 torr Number of stages 2 Permissible ambient temperature range (operation) 15 - 40 °C Permissible ambient temperature range (storage) -10 - 60 °C Max. outlet pressure (abs.) 1.1 bar Oil capacity min./max. 0.45 / 0.85 l Inlet connection small flange KF DN 25 Outlet connection small flange KF DN 25 Rated motor power 0.30 kW Rated speed 50/60 Hz 1500/1800 min-1 Protection class IEC 60529 IP 40 Dimensions (L x W x H) 503 mm x 156 mm x 240 mm Weight 24.8 kg Noise (sound pressure level) in dBA at 50 Hz or 1500 rpm/62% (VARIO)/1500 rpm (VARIO-SP)/12500 Upm (VACUU·PURE®) - 52 dBA NRTL certification - No

Condition: new, Year of construction: 2025, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 600-700 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Iedpfxjndn Age Abbstf Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2026, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 800-900 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Itsdpfx Asng Exasbbjf Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Year of construction: 2008, condition: good (used), Machine type: Finishing machine Manufacturer: Supfina Grieshaber GmbH & Co. KG Model: 622/1 Serial number: 760001 Year of manufacture: 2008 Itsdpfjlrt Sajx Abbsf Available immediately Ex site for self disassembly Optionally we can offer dismantling and loading

Condition: new, Year of construction: 2025, Blasting container for blasting glass beads and ceramic balls with drum magnetic separator and stainless steel grating floor. Inner dimensions L=5850 W= 2300. Side Door Open for easy loading with the forklift. Ijdpeg S Rt Tefx Abbotf

Year of construction: 2020, condition: new, Title Strassburger Filter SF400oDEC/30S Integra – Stainless Steel Plate and Frame Filter Press – Year 2020 – NEW / Unused Short Description For sale: unused, factory-sealed plate and frame filter presses from the renowned German manufacturer Strassburger Filter GmbH + Co. KG. The units are in brand-new condition, have never been commissioned, and remain in their original packaging from the factory. Manufacturer Strassburger Filter GmbH + Co. KG (Germany) Model / Type SF400oDEC/30S, Integra format Machine designation: FI6722 – FP PRE 1 Year of Manufacture 2020 Serial Number Among others: 032003303920 (additional serial numbers available) CE Marking Yes Condition Brand new / unused Factory-sealed Never installed, never used for production Stored in warehouse Quantity Available 4 identical units available New Price Original price €94,000 per unit (Total value for 4 machines: €376,000) Design / Material All stainless steel Plate and frame filter press Gasketed plates Pharma / biotech specification Hydraulic closure incl. hydraulic unit CE-compliant Technical Data Plate format: 425 × 400 mm Number of filter chambers: 28 Total filter area: approx. 3.4 m² Total volume: approx. 13.6 liters (100%) Max. operating pressure: 6 bar Max. operating temperature: 95 °C CIP / SIP capable (cleaning up to 121 °C) Dimensions & Weight Length: approx. 1,649 mm Width: approx. 600 mm Height: approx. 1,145 mm Weight (filter frame): approx. 480 kg Weight (plate pack): approx. 120 kg Plate Pack 14 filter plates 13 filter frames 1 end frame 1 partition plate 28 filter layers per setup Hydraulics & Drive Hydraulic closure Hydraulic power unit included Motor power: 1.5 kW Electrical connection: 400 V / 50 Hz Solenoid voltage: 24 V DC Compressed air requirement: 3.0 bar Connections Product inlets and outlets: DN25 Iedpsx Ihufsfx Abbstf Vent / drain: DN15 Connections according to DIN 11864-2 Drip tray included Areas of Application Pharmaceutical production Biotechnology Chemical industry Pre-filtration Precipitation and clarification processes Location Germany Inspection by appointment Immediately available

Condition: refurbished (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: 30214501, turning length: 2,000 mm, total length: 12,000 mm, WFL Millturn M60/2000 WORKING RANGE center distance mm 2000 swing over bed, turning diameter mm 690 MAIN DRIVE AC-drive with 2 gear steps drive power 100% duty cycle kW 40 max. speed min-1 3300 max. torque at the spindle 100% duty cycle Nm 1830 TAILSTOCK quill diameter mm 140 quill travel mm 160 quill force (adjustable) N 3500-31000 quill with installed live center MK 5 TOOL HOLDER (single tool holder, turning-boring-milling unit) AC-drive drive power 100% duty cycle kW 30 speed range max. min-1 6000 max. torque at the spindle 100% duty cycle Nm 315 Itodpfx Aju Hl R Tobbsf travel vertical to the X/Z-plane (Y-axis) mm 300[-125/+175] pivot capability of the milling spindle (B-axis) ° -110/+90 spindle head acc. DIN 69893 HSK-A100 spindle diameter in front bearing mm 100 DIMENSIONS length (max. tool magazine) m 11 width/height m 3,9/3,3

Condition: excellent (used), functionality: fully functional, Year of construction: 2018, load capacity: 4,000 kg, lifting height: 10,000 mm, battery voltage: 48 V, empty load weight: 9,000 kg, General information: The HUBTEX 2125-PU/SO with model MQ 40 is an electric multidirectional sideloader with a load capacity of 4 tons and a cross-seat cabin. This forklift is suitable for warehouse areas where maximum flexibility and maneuverability in narrow aisles are required to handle loads of up to 4000 kg. M = Multidirectional steering Q = Cross-seat cabin 40 = 4,000kg 2125 = Series PU = Vulkollan tires SO = fork tilting and lowering, extendable forks to 1500mm, hydraulic fork width adjustment Additional equipment/modifications: Iodpfxsx Aqaqe Abbetf - Camera system on the right and left of the forks, with monitor in the cabin - Positioning lasers on the right and left of the forks - Soft-stop feature when lowering the forks and when crossing the telescopic fork extension steps

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, Precision winding machine for films and web materials. Designed for consistent unwinding, guiding, and rewinding of roll materials. Integrated safety system with protective glazing, laser start position indicator (green), emergency stop switches, and pneumatic film guiding. Machine frame made of steel, electrically controlled drive. Ideal for production lines in coating or laminating technology. Iedpfx Aboxzuiyobstf

Condition: excellent (used), Stations/Equipment: Unwinder Rewinder Extraction system incl. shredder (4x Lundberg Type WT200-200U - year 2018) Inert enclosure Itodpfjxzufhjx Abbsf Busbar laminating unit Cutting units Laminating units / adhesive application units Heated rollers Master computer Control cabinets Drive motors Gantry crane Corona treatment

Condition: new, Year of construction: 2025, PROFILE BENDING ATTACHMENT PB20 The PB20 profile bending attachment is the optimal supplement for tube bending on the 3000 and 6000 models. The device can be easily and quickly mounted on the bending shaft without the use of tools. The workpiece is clamped onto the turntable with the clamping device and pulled around the bending tool. With this system, leg lengths to be bent can be accurately measured in conjunction with a length stop and can be bent with repeatable accuracy. TECHNICAL DATA: - Bending capacity steel 37: 100 x 10 mm, Ø 20 mm. - Many standard tools available - Special tools possible - Sharp-edged tools with bending radius R2 or 5 mm - round tools R 10 to 25 mm for bends max. 260° optional Iedpsnh R Eksfx Abbetf OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, the mobile bending machine with great performance: The compact, mobile design enables precise and repeatable bending stationary and directly at the installation site up to a tube diameter of 35 mm, CU 42 mm. A powerful three-phase motor and a precision gearbox provide powerful drive. The motor speed is automatically adjusted, resulting in increased return speed and shorter cycle times. Optimum bending accuracy and very high repeatability are achieved by position detection directly on the bending axis. The bending angle is easily and quickly set to 0.5° using pushbuttons. The large LCD display clearly shows the angles. The storage of up to three bending angles enables the rational bending of tubes with different bending results. For transport, the compact unit with accessories can be neatly and safely stored in sturdy transport cases. The "upright tube and rotating tool" principle ensures low space requirements during bending. Sliding shoes are used for thin-walled tubes to enable crease-free bending and to bend bends with the slightest deformations from, for example, stainless steel and copper tubes. With the PB20 profile bending attachment, flat, square and round iron can be bent without problems. POSSIBLE APPLICATIONS: - Hydraulic piping - Sample construction - Sanitary and heating construction - Technical data: - Bending capacity Ø 6 to 35 mm, CU Ø 42 mm depending on material. - Bending radius min/max: 36 mm/150 mm - Precise digital bending angle adjustment 0.5°. - Maximum 180º bending result; for special applications Endless operation possible - Hexagonal shaft 40 mm for quick tool change - Safety foot switch with emergency stop function - Alternating current 230 V connection - Weight 29 kg - Frequency converter and three-phase motor - 3 bending angles storable OPTIONAL ACCESSORIES: - Slide shoe holder - double roller holder - Profile bender PB20 - for bending flat and square bars up to max. 80 x 8 mm, round bars up to max. 20 mm - tripod base - machine case - tool case - Small bending device KBV - Special tool according to specification Iedjnfvx Nepfx Abbstf OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, machine/vehicle number: 1018, THE POWERFUL BENDING MACHINE FOR EXTREME USE: The compact bending machine enables precise and repeatable bending up to an outer diameter of 100 mm stationary and directly at the assembly site. Transport is possible with lift trucks or the optional rollers. A powerful three-phase motor and a precision gearbox provide a powerful drive. The machine convinces with its compact and slim design as well as the very free bending range. Optimum bending accuracy is achieved by position detection directly on the bending axis. The bending angle is set easily and quickly via a convenient and menu-driven user interface in 14 languages with touchscreen control, which guarantees even more intuitive operation. For more complex bending tasks, 100 bending programs can be stored, with an angle sequence of max. 8 bends per geometry. The multifunction control allows variable adjustment of the bending speed for forward and backward travel, and a parameterizable overbending function is provided to compensate for material springback.With the help of the four material characteristics, the material is automatically overbent to the required bending angle, thus realizing an exact bending result. The principle of "stationary tube and rotating tool" ensures low space requirements during bending. Sliding shoes are used for thin-walled tubes to achieve a wrinkle-free bending result and to bend bends with minimal deformations from e.g. stainless steel and copper tubes. With the profile bending attachment PB20 flat, square and round bars can be bent without any problems. Extremely small bending radii are made possible with the KBV small bending attachment. POSSIBLE AREAS OF APPLICATION: - Plant engineering - Hydraulic piping - Meander bending - prototyping - Sanitary and heating engineering - shipbuilding TECHNICAL DATA 10000: Bending capacity: up to 100 x 5 mm, 55 mm solid material three-phase current 400 V - Bending radius up to 500 mm - Multifunctional machine control Bending angle adjustment (0,1°) - Maximum bending angle 240 - Safety foot switch with emergency stop - Weight 600 kg OPTIONAL ACCESSORIES: - Adapter system for tools from model series 3000/6000 with bending radius from 45 mm, incl. hexagonal shaft 40 mm - Profile bender PB20 - for bending flat and square bars up to max. 100 x 10 mm, round bars up to max. 20 mm - Small bending device KBV - Special tools according to specification - Software adaptations for special tasks OUR SERVICE: Ijdpendk N Asfx Abbetf - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site