Used Small Series Press for sale (18,051)

Condition: used, CNC press brake FASTI type 904-125/30 serial no. 95-904-5775 year of construction 1995 Pressure capacity 125 ton. Working length 3050 mm Stroke approx. 335 mm Stand projection 300 mm Clearance between the side uprights 2550 mm Tool installation height max. 465 mm (opening width between the tool holders) Table width 90 mm (the clamping system is mounted on the table) Table height above floor 875 mm (910 mm with clamping system) Backgauge X-axis 500 mm Backgauge R-axis 115 mm Backgauge Z-axis approx. 1950 mm Lowering speed Y rapid traverse 90 mm/s Lowering speed Y-operation 8.9 mm/s Return stroke speed Y-retraction 75 mm/s Oil filling approx. 160 liters Motor power 18.5 kW Mains connection 400 Volt, 50 Hz, 20 Amp. - 7-axis CNC control DELEM type DA 58 with LCD screen - 1 axis for back gauge - stop depth (X-axis) - 2 axes for back gauge - fence height (finger R1 + finger R2) - 2 axes for back gauge - stop finger, laterally movable (finger Z1 + finger Z2) - 2 axes for press beam with servo valves and measuring system Y1 and Y2 Iijdpfx Ashmmfksb Nob - Operation via electric foot switch and 2-hand control panel or 2-hand control panel only - Hydraulic tool clamping for the TRUMPF upper tool system, with 20 mm clamping groove - Hydraulic tool clamping for the lower tool with 13 mm table groove, depth 21 mm (tool pin 13 x 20 mm) - FIESSLER safety light barrier, type AKAS - 2 material support arms at the front, manually movable to the side and height-adjustable - Electrical diagram, hydraulic diagram, user manual for control available - Control cabinet on the machine - without tools Space requirement L x W x H 5000 x 2500 x 3050 mm Transport dimensions L x W x H 5200 x 1900 x 2950 mm Weight 8.5 tons. Good condition

Condition: used, Single-column toggle press MAY - MAYPRES - KOMATSU Type MKN 1-63/6 Eccentric toggle press, eccentric press Year of manufacture approx. 1984 Pressing force 60 tons Thrust 160 mm Table size 580 x 360 mm Ram surface Ø 270 mm Clamping pin bore Ø 40 mm Distance between columns 218 mm Ram stroke 60 mm Ejector stroke 15 mm Ram adjustment travel 30 mm Max. installation height 300 mm (with intermediate table plate) Stroke rate 70 strokes per minute Motor speed 1400 rpm Motor power 3 kW Power supply 380 V, 50 Hz - Pneumatic clutch and mechanical brake with pneumatic release (separate clutch-brake combination) - Table intermediate plate L x W x H 580 x 360 x 58 mm, with holes and cutouts - Mechanical ejector, ejector device in the machine table, Ø 80 mm - Electric two-hand control and foot switch Iiodpfxov Uraas Ab Nob - Movable safety screen, UNIDOR protective housing with pneumatic front screen - BALLUFF cam switch Space requirement L x W x H 1400 x 1200 x 1850 mm Weight 3 tons Good condition

Condition: used, Single-column hydraulic press with draw cushion RÖCHER Type REP 100.01 SZ Hydraulic deep-drawing press Machine No. 15.499 Year of manufacture 2003 Pressing force: 100 tons Ram stroke: 500 mm Throat depth: 370 mm Installation height: 600 mm Table surface: 850 x 700 mm with a drop-through hole Ø 150 mm Ram surface: 700 x 600 mm Ram ejector force: 16 tons (160 kN) Ram ejector stroke: 100 mm Ram ejector with internal thread M24 x 1.5 mm Draw cushion force: 40 tons (400 kN) Draw cushion stroke: 200 mm Draw cushion area: 530 x 530 mm Pressure holding time: 0 to 90 sec. Table height above floor: 910 mm Hydraulic operating pressure: max. 300 bar Hydraulic tank capacity: 700 liters Approach speed (rapid traverse): approx. 400 mm/sec. Pressing speed up to 23.8 tons (238 kN): 5 to 68 mm/sec. Pressing speed up to 100 tons (1000 kN): 5 to 16 mm/sec. Return speed: 50 to 400 mm/sec. Main pump drive power: 18.5 kW Auxiliary pump drive power: 4 kW Power supply: 400 Volt, 50 Hz (63 Amps) - Operation and programming via PC 670 touch panel, keyboard and mouse - Machine control via SIEMENS S7-300 PLC system - Ram stroke and press force programmable via control system - Draw cushion with drawing and ejector function - Draw cushion force infinitely adjustable - Ram and draw cushion equipped with direct linear measurement system - Draw cushion can be moved in and out under the press area, for punching work using the drop-through hole - Floor-level installation, draw cushion does not penetrate the floor - Pressure and stroke cutoff - Fixed stop with indirect measurement system - Pressure holding time infinitely programmable - Table with holes for the draw cushion ram rods - Ram with ejector - Knock-out damping - Stroke triggering via two-hand operation, foot switch, hand lever and push button on the control panel - LEUZE light barrier as reach-in protection for safety operation - Front mirror columns on the press table can be shifted laterally - Electrical control cabinet mounted on machine frame - Hydraulic oil cooler with fan motor (oil-air cooling) - Manual central lubrication pump - 2x hose connections for tool tempering or cooling at the ram - Piece counter in the control system - 306 read operating hours - Operating manual, hydraulic diagram, and electrical diagram available Iedpsyupulofx Ab Neib Space requirements (L x W x H): 3100 x 1800 x 4160 mm Weight: approx. 13 tons Very good condition, as new

Condition: used, Hydraulic Synchronizing Press, Spotting Press AGEO Type GHP 200 H6 4-Column Hydraulic Press, Tool Trial Press, Spotting Press Serial No. 21169 Year of manufacture: 1993 Pressing force: 200 tons Clearance between uprights (front): 1200 mm Upright opening (side): 650 mm Table surface: 1560 x 1010 mm Ram surface: 1560 x 1010 mm Ram stroke: 575 mm Draw cushion stroke: 300 mm Draw cushion holding force: 63 tons Isdswva I Hspfx Ab Nsib Draw cushion ejector force: 30 tons Max. installation height: 775 mm Table height above floor: 1000 mm Guide column Ø: 140 mm Clamping pin bore in ram: 64 mm Pressing speed: 0 to 10 mm/s, stepless Return speed: 0 to 20 mm/s, stepless Main motor power: 22 kW Control pump motor power: 5.5 kW Connection: 400 Volts, 50 Hz - Table and ram with 22 mm T-slots - Two pressure cylinders with electronic precision synchronization control - Stepless electronic stroke limitation (top and bottom with digital travel measurement and position display) - Mechanical safety support device (prevents ram from dropping due to dead weight) - Single-hand and two-hand operation - Electrical tool safety via signal contact - Pressure presetting independent of stroke (via keypad, digital pressure display) - Travel measurement system right and left via rotary encoders - Electrical control: MS-DOS PC with Ageo H v2.23 control software - Operator panel with swiveling display - Stroke movement and press force adjustable via joystick - Adjacent hydraulic power unit with electrical cabinet - Hydraulic draw cushion under the press table - Draw cushion with ejector function - Continuous stroke control - Floor-level installation - Electrical oil temperature monitoring - Operating manual with circuit diagrams Space required by press (upright) L x W x H: 1800 x 1010 x 3470 mm Space required for horizontal transport L x W x H: 3500 x 1800 x 1200 mm Net weight press: 13 tons Space for hydraulic power unit L x W x H: 1000 x 800 x 3040 mm Net weight hydraulic power unit: approx. 1 ton The machine was used as a tool trial press in a toolmaking workshop. Very good condition.

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced Iiedpfxsvq Rtks Ab Neb - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: used, Hydraulic notching machine with adjustable angle SIMASV model AV 220-6PA Serial no.: C1524 Year of manufacture: 1996 Blade length: 220 mm Material thickness (steel): 6 mm Material thickness (stainless steel): 4 mm Table dimensions: 950 x 790 mm Table height: 940 mm Motor power: 3 kW Power supply: 400 Volt, 50 Hz - Operation via push-button or foot switch Iodpsrzfh Hsfx Ab Noib - Adjustable notching angle from 30° to 140° - Angle adjustment via 2 handwheels (right and left) - Hydraulic clamping for the adjustable blades - Electric foot switch - 2 adjustable stop rails with angle scale - Multiple millimeter scales integrated into the table top - HSS blades newly ground, as new Required space (L x W x H): 1000 x 950 x 1470 mm Weight: 750 kg Very good condition

Condition: used, Double column hydraulic press SMG type HBP 200 - 2000 / 2000 make no. 7.4117 year of construction 1986 - rebuild 2000 pressure force 200 ton. Stand passage front 2050 mm column passage sideways 2030 mm table area 2800 x 2000 mm ram area 2000 x 2000 mm ram stroke 700 mm installation height max. 1850 mm Table height above floor 750 mm ram retraction force 33 ton. Iiedpjdzp Tcjfx Ab Nob Rapid feed speed 500 mm/s Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety distance 230 mm Motor power main motor 75 kW Motor power control pump 11 kW Mains connection 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots at the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking at TDC - Measuring system with glass scale - Electrical control renewed in 2000 with SIEMENS SPS S7 - adjacent switch cabinet - 2-hand control panel adjacent - ground level installation - central lubrication - Operating instructions with circuit diagrams Space requirement of the press standing L x W x H 3700 x 2900 x 5900 mm Machine height complete with motor 5900 mm Space requirement for horizontal transport L x W x H 5900 x 3250 x 2950 mm weight 38 ton. The machine was used as a production press at Volkswagen until 2000. From 2000 the machine was used as a tool testing press in a tool shop. good condition

Condition: used, Year of construction: 1990, operating hours: 83,000 h, functionality: fully functional, Complete precision stamping line ready for relocation. Centre piece is a BRUDERER BSTA 50HL (500 kN, year 1990, Kom. 9443) equipped with control and Unidor tool and press safety monitoring system. The line includes a sound-insulating safety cabin, finished-parts output conveyor, Soprem H1000/1000ZV/10M/LK.LF/N1/G coiling machine (2003), and Soprem BR19/160/12/U Straightening machine (2003). Available as a complete turnkey lot. Technical Specifications Press Manufacturer BRUDERER AG, Frasnacht, Switzerland Machine Model: BSTA 50 HL Serial / Commission No.: Kom. 9443 Year of Manufacture: 1990 Operating Hours: 82,600.0 h (as shown on press control) Total Weight approx.: 8,700 kg Sound Enclosure / Cabin Included: W 3,460 × L 2,331 × H 3,910 mm Stroke range (adjustable): 16 / 19 / 25 / 32 / 38 / 44 / 51 mm Ram adjustment range: 64 mm Tool opening width (max.): 950 mm Bolster plate — Width × Depth: 930 × 650 mm Iiodpfx Ajy S E U Rob Nob Baseplate opening W × D: 900 × 200 mm Strip feed height (adjustable): 60 – 140 mm Max. strip pass-through width: 250 mm Feeding device: BBV 195 - 85 Feeding angle: 90 degrees Max. Strip thickness: 4 mm Max. Strip width: 160 mm Feed length: 0 – 85 mm Supply voltage: 3 × 400 V / 50 Hz Main motor power: 28 kW Control voltage (DC): 24 V DC Pneumatic supply: 6 – 10 bar (R ½" connection) Press width (with feeder) approx. 2,471 mm Press depth approx. 1,302 mm Press height approx. 3,165 mm Including Soprem H1000/1000ZV/10M/LK.LF/N1/G coiling machine (2003) Including Soprem BR19/160/12/U Straightening machine (2003) Includign Unidor press and Tool Safety System Finished-parts output conveyor belt Sound-insulating safety cabin / enclosure Original technical documentation and schematics

Condition: new, power: 265 kW (360.30 HP), fuel type: diesel, number of seats: 49, gearing type: automatic, axle configuration: 4x2, emission class: euro3, Year of construction: 2026, Equipment: ABS, air conditioning, cruise control, electronic stability program (ESP), power assisted steering, traction control, - Adaptive cruise control - Autoradio - CD - EBS - Powered windows - Power windows front - Reverse camera = Additional options and accessories = - Airbags - Air suspension - Alarm - Aluminium fuel tank - Bluetooth - Central doorlocking - Central locking - Passenger seat - Radio/cassette player - Side door - Toilet = Remarks = Mercedes-Benz Bus Chassis with Marcopolo Viaggio 1050 G8 The Mercedes-Benz bus with Marcopolo Viaggio 1050 G8 body offers a reliable solution for comfortable passenger transport. This combination of a robust chassis and innovative body is ideal for long-distance trips, regional routes, and luxury tourist shuttles. With advanced safety features and efficient technology, this bus guarantees low operating costs. Worldwide, it is the most produced bus combination thanks to unmatched comfort and durability. Technical Specifications Mercedes-Benz Bus Chassis: - Engine: 12.8-liter 6-cylinder diesel engine, 450 hp (330 kW), 2200 Nm torque, Euro III-compliant for reliable performance. - Transmission: Automated ZF Traxon 12-speed gearbox with integrated intarder for smooth and safe deceleration. - Driver Assistance Systems: Hill Hold for effortless start-stop driving, Power mode for overtaking, Eco-Roll function for fuel savings. - Brakes: Disc brakes on front and rear axles with ASR, EBS, ESP, and emergency brake light (ESS) for optimal safety. - Fuel Tank: Large capacity for long-distance driving with efficient fuel consumption. - Wheels: Polished aluminum rims for durability and premium appearance. - Fleet Management: FMS interface for integration with external management systems. - Safety: Fire detection system in the engine compartment for added protection. Marcopolo Viaggio 1050 G8 Body: - Exterior: Stylish DCPD front with distinctive design line, optional LED headlights for improved visibility. - Interior: Modern with high-quality audio system, WiFi, camera systems, and screens (on request). - Driver’s Cabin: Ergonomic dashboard with extra storage, multiplex control, assistance button, and shortcut keypad. - Access: Wide steps with LED lighting and antibacterial handrails for safe boarding. Iijdsy R Arwepfx Ab Nob - Seats: G8 seats with USB ports, adjustable backrests, and maintenance-friendly design. Advantages: - Operational Flexibility: Customizable configurations for diverse transport needs. - Durability: Robust construction and low maintenance extend lifespan. - Comfort & Innovation: Luxurious interior and technology for passengers and drivers. - Efficiency: Low fuel consumption and easy maintenance access minimize costs. Applications: - Regional Lines: Reliable and comfortable for daily public transport. - Long-Distance Tourism: Ideal for multi-day trips with a focus on luxury. - VIP and Shuttle Transport: Perfect for exclusive transfers for business travelers and events. - Sports Teams: Spacious layout for teams and equipment. Power in Comfortable Transport: The Mercedes-Benz bus with Marcopolo Viaggio 1050 G8 combines proven technology with innovative design, delivering unmatched comfort and safety. This bus is the ideal choice for demanding transport challenges — from regional routes to luxury tourist travel. Contact: Reach out at or visit . =...

Condition: good (used), Year of construction: 2021, functionality: fully functional, pressing force: 58 t, Very good condition, fully functional, low operating hours, year of manufacture 2021, pressing force 58 tons. New price: seen for €19,500 Iisdpfsyzw U Uex Ab Nob Pressure cylinder has been dismantled for transport, inspection possible by appointment. Further presses in stock.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Iiodpfjy R Nnfex Ab Neb Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Condition: used, Year of construction: 1964, machine/vehicle number: 63/10.2995-96, pressing force: 1,200 t, total length: 5,300 mm, total width: 2,690 mm, total height: 9,300 mm, overall weight: 360,000 kg, Press force: 1,200 tRam stroke: 600 mmRam adjustment: 500 mmStroke rate: approx. 10 – 16 strokes/minShut height: approx. 1,250 mmDrawing equipment:Drawing cushion force: approx. 240 tDrawing cushion stroke: approx. 250 mmPneumatic ejector in ram:Force: approx. 95 tStroke: approx. 150 mmTable size: approx. 3,500 x 1,900 mmHeavy-duty mechanical eccentric press in robust double-column design from Schuler, suitable for industrial applications as well as classical forming and deep drawing processes.The machine features a press force of 1,200 t with a fixed ram stroke of 600 mm and a ram adjustment of 500 mm. The stroke rate ranges from approx. 10 to 16 strokes per minute, allowing flexible use depending on the application.The working area is designed with a table size of approx. 3,500 x 1,900 mm, offering sufficient space for medium to large tooling.A key feature is the movable / sliding press table, which significantly simplifies setup and tool change and makes the machine ideal for handling heavy tools.The integrated drawing equipment (drawing cushion) provides approx. 240 t of force with a stroke of 250 mm, enabling demanding forming and deep drawing operations.In addition, the press is equipped with a pneumatic ejector in the ram (approx. 95 t / 150 mm), supporting automated part removal. Installation height max.: 1,250 mm Weight approx.: 360,000 kg Machine table clamping surface: 3500 x 1900 mm Passage between the uprights: 3,600 mm Serial number: 63/10.2995-96 Pressing force max.: 1,200 t Dimensions (LxWxH) approx.: 5300 x 2690 x 9300 mm Year of construction: 1,964 Condition: in working order Terms of payment: 100% prepayment before pick-up Terms of delivery: From foundation Ijdpfx Asy S Nhzeb Noib under power: Yes

Condition: good (used), Year of construction: 2007, frame press GOMA PHA 3500 Door Press hydraulic Location Gorzów Wlkp. Conditions of delivery OWN RECEIVING Cost of delivery to be negotiated Startup type to be negotiated Description Iijdsdntc Nopfx Ab Njb Comments Working space 3500 x 2300 mm 1000kG (daN) pressure, engine at hydraulic unit 2,2 kW lenght 3500 mm hight 2300 mm weight 2000 kg agrageate hydraulic

Condition: used, Year of construction: 1977, pressure 25 t throat 250 mm stroke 400 mm table surface area 600x480 mm ram surface Ø135 mm Isdpfx Ajy Sliueb Njib table height 980 mm weight of the machine ca. 1,5 t dimensions of the machine ca. 2000x2000x2700 mm

Condition: excellent (used), Year of construction: 2006, Dimension: 2650 x 2100 x 2100 mm Clamping Force: 635 KN Working pressure: 206 bar Piston diameter: Ø200 mm Stroke: 140 mm Daylight: 150/180 mm Heating plant dimension: 250 x 300 mm Max. mass of heating plant: 70 kg Oil reservoir: 100 l Rated power: 19.66 kW Heater capacity: 9.6 kW Vacuum motor power: 2,6 kW Between light curtain and mould area: 270 mm Stroke of vacuum cover: 140 mm Ijdpfx Aey Snlxsb Neib The vulcanizing press from manufacturer PAN STONE, model S-V-65-2RT-PCD, was used by a renowned German company specializing in sealing technology and electromobility. This company is known for its high quality and innovation in seal production. The machine was part of a production line responsible for manufacturing high-performance seals used in various industries. It was always professionally maintained and repaired, which explains its excellent condition. This press offers you the opportunity to invest in proven technology that was utilized by a leading company in Germany.

Condition: good (used), Year of construction: 1987, functionality: fully functional, Clamping unit heating capacity, 1 heating rod / 8 heating rod: 0,48 / 0,9 kW clamping force: 2 x 500 kN heating plate dimensions: 550 x 600 mm piston stroke: 250 mm Iedpoy Snkbsfx Ab Neib diameter of piston, main cylinder: 240 mm diameter of piston, locking cylinder. 39 mm locking cylinder: 260 mm Return capacity: 2 x 600 kN dimensions: 2600 x 2100 x 2100 mm weight approx.: 5 t

Condition: good (used), Year of construction: 1994, Clamping Unit: Clamping force: 7,000 kN Operating pressure: 250 bar Specific pressing pressure: 610 N/cm² Number of levels: 2 Installation height with 75 mm heating plate & 20 mm insulating plate: approx. 2x 190 mm Piston stroke: approx. 400 mm Piston 1 diameter: 543 mm Clamping force, rapid traverse: approx. 2 x 85 kN Iiodpfjy Sni Rsx Ab Nsb Retraction force: approx. 2 x 47 kN Operating pressure: 300 bar Piston 2 diameter: 60/40 mm Stroke: 400 mm Estimated weight: approx. 16 tonnes Hydraulic System: Pressure adjustment: 40 - 300 bar Flow rate regulation: 0 - 99 % Flow rate l/min (HD): 45 against 300 bar Drive power: 22 kW Tank dimensions (LxWxH): 1000 x 770 x 535 mm Closing Speed: Rapid traverse: approx. 40 - 50 mm/s Slow closing: approx. 0 - 20 mm/s Pressing speed: approx. 0 - 3 mm/s Slow opening: approx. 0 - 20 mm/s Opening, rapid traverse: approx. 0 - 60 mm/s

Condition: used, Year of construction: 2005, functionality: fully functional, Clamping force: 4900 kN Working pressure: 206 bar Heating plate dimensions: 700 x 700 mm diameter of piston: 558,8 mm max. stroke: 250 mm daylight: 300 mm max. mass of heating plant: 560 kg capacity of oil tank: 1100 l rated capacity: 82 kW heating capacity: 56 kW enginge output, vacuum motor: 4 kW Stroke of vacuum cover: 200 mm dimensions: 3975 x 2935 x 2555 mmm Equipped with a crane runway (monorail) with three chain hoists Producer: STHAL Year: 2011 Lifting capacity: 3 x 400 kg Iiedpfx Aoy Sniwob Nob Lenght of crane runway: ca. 3500 mm Rolling chassis Lifting capacity: 400 kg Lifting height: 3000 mm stroke speed - main stroke: 4 m/min stroke speed - fine stroke: 1 m/min The vulcanizing press from manufacturer PAN STONE, was used by a renowned German company specializing in sealing technology and electromobility. This company is known for its high quality and innovation in seal production. It was always professionally maintained and repaired, which explains its excellent condition. This press offers you the opportunity to invest in proven technology that was utilized by a leading company in Germany.

Condition: used, Year of construction: 2003, functionality: fully functional, machine/vehicle number: 3599, total height: 2,600 mm, total length: 2,200 mm, total width: 2,200 mm, overall weight: 16,300 kg, pressing force: 100 t, passage height: 1,200 mm, passage width: 1,200 mm, Hydraulic press (previously used for lamination of door panels) Iodpfx Abowt Axcs Neib Pressing area: 1300x1100 mm Press cylinders: 4x D110 mm Maximum pressing force: 1000 kN The machine is currently disassembled and was fully operational until it was taken apart. For an additional charge, two compatible heating plates including control cabinet are also available.

Condition: new, Year of construction: 2024, functionality: fully functional, Discover the powerful Durma press brake at our demonstration center in Saerbeck. As a manufacturer, we offer you maximum precision and efficiency with a capacity of 3050 mm in length and 175 tons. Benefit from our comprehensive all-in-one service: We take care of transportation, installation, commissioning and offer you a one-year warranty as well as fast and reliable service. Visit us and see the quality and versatility of this first-class machine for yourself. Standard equipment Capacity (length - ton) 3050mm - 175t Installation height 530mm Outreach 450mm Stroke 265mm Servo drive Y1, Y2, X - 3 axles Control unit - DT 15 Iijdotr Dk Eopfx Ab Nsb Manuel F. AKAS FPSC safety system CE-Fiessler Akas Servo motor backgauge & linear guide & Ball screw system Manual crowning European tool holder Sliding front arms Options - DELEM 69S control unit (3D control) -Motorized crowning - 6 axes X=650mm Y1, Y2, X ,R , Z1, Z2 (6 axes controlled press brake) press brake) -Lower tool European M.460R.85 -European upper tool P135.75.R08

Year of construction: 2024, condition: new, Here a new AD-R 37220 is offered:Bending force: 220 tonsBending length: 3700Pass between uprights: 3100 mmHub: 265 mmInstallation height: 530 mmExtension: 410 mmTable height: 900 mmTable width: 104 mmY Fast speed: 160 mm/sec.Y Working speed: 10 mm/sec.Y Withdrawal speed: 120 mm/sec.X axes Working speed: 250 mm/sec.R axes Working speed (manual): 250 mm/sec.R axes Travel: 250 mm/sec.X axes Distance: 650Length: 4950 mmWidth: 1770Height: 2900Total weight: 14100 kgOptions:CE with manual F.AKAS II M -FPSC-B-C Safety cover Iodpfjd S I R Tex Ab Noib

Year of construction: 2024, condition: new, Everything is configurable on demand, very short production & delivery time. We will be happy to provide you with further information on request. Technical data: AD-R 60400 Bending force: 400 tons bending length: 6050 mm passage between the uprights: 5100 mm stroke: 365 mm Installation height: 630 mm Abroad: 510 mm Optional foreign diameter: 750 mm | 1000 mm | 1250 mm table height: 1220 mm table width: 154 mm Y Fast speed: 120 mm/sec. Y Working speed: 8 mm/sec. Y Retraction speed: 100 mm/sec. X axes working speed: 250 mm/sec. R axes working speed: 140 mm/sec. R axes travel: 250 Engine power: 37 kW length: 7500 mm Ijdpfx Abjfin Hwj Noib width: 2110 mm height: 3710 mm Weight approx. 35 tons With more than 60 years of experience in research and production of machines for sheet metal working, 8,000 machines produced annually in three technologically advanced production facilities covering a total area of 150,000 m², the Durmazlar Group and its DURMA machines are today among the internationally renowned manufacturers in their sector, whose products are sold in 120 countries. With the branch in Staufenberg near Gießen, Durma Maschinen GmbH is now an important part of the Central Hesse region. Here here we are your direct contact person from the ranks of Durmazlar, who will competently assist you with advice and practical support when it comes to machines for sheet metal processing. Our demonstration center gives you the opportunity to get an overview of our

Year of construction: 2024, operating hours: 32 h, condition: new, Make: DURMA Type: AD-S 30175 Year of construction: 2020* bending length: 3050 mm Press force: 1750 kN Control: DELEM DA-66T Operating hours: 32 h Controlled axes Backgauge: X,R,Z1,Z2,+Delta X +/- 125 mm CNC controlled passage between the uprights: 2600 mm stroke length: 265 mm Installation height: 530 mm table width: 104 mm table height: 900 mm Stands projection: 410 mm travel range X-axis: 650 mm traverse speed X-axis: 500 mm/s travel range R-axis: 250 mm infeed speed: 160 mm/s folding speed: 10 mm/s Retraction speed: 100 mm/s Dimensions L/W/H: approx. 4250x1700x2750 mm Weight: approx. 11500 kg Standard equipment Y1,Y2,X,R - X=650 mm Control: CNC Cybelec ModEva 19T - PC 1200 3D SW D-BEND 3D CAD/CAM import & simulation program CNC controlled motor-driven crowning European tool clamping system 60 mm die holder (only for European die system) Throat 410 mm 2 support arms movable from the front with T-slot and tilt stop Backgauge system: Siemens DC Servo motorized with linear guide and ball screw Protective covers CE Marking Extended equipment Safety system CE standard for EU: FIESSLER AKAS-3P motorised+FPSC (SAFETY PLC) Controlled axes Backgauge: X,R,Z1,Z2,+Delta X +/- 125 mm CNC controlled Ijdpfx Abjdx Nlue Neib Control: DELEM DA-66T Hydraulic top tool clamping Wila NSCL-II-HC/UPB - PREMIUM - 250 t/m Hydraulic bottom tool clamping Wila NSCR-II-HC-CNC/UPB - PREMIUM - 300 t/m Powerpack for hydraulic clamping AP3-AP4 Bending aid -

Year of construction: 2024, condition: new, The DA-69T control offers both 2D and 3D programming, which includes automatic calculation of the bending sequence and collision detection. The entire 3D machine setup includes multiple tool stations and provides immediate feedback on product feasibility and handling. DA-69T features: - 3D- and 2D- graphical touch screen programming mode - 3D representation in simulation and production - 17-inch TFT colour display with high resolution - Complete Windows Application Suite - Compatible with Delem Modusys (module scalability and adaptivity) - USB, peripheral interface - Open system architecture - Sensor Bending and correction interface - Profile-T3D offline software - great contribution to environmental protection, climate change and the greenhouse effect will thank us, the next generation will thank us too! - Fully electronic drive - Up to 30% higher productivity - Up to 50% energy savings through Start-Stop technology - Faster than hydraulic press brake - Reduced operating costs - Much lower service and spare parts costs (the electric press brake is technically much simpler and almost maintenance-free) Iiodpfxod Sak Se Ab Nob - No harmful oil - quiet - efficient - independent of Hyd. Oil - Low noise operation - relaxed and stress-free bending - Complete work area - Touchscreen operation Machine dimensions: ( L x W x H ): 2.150 mm x 1.650 mm x 2800 mm Technical details: bending length: 1.250mm Free stand passage: 1.300 mm Press

Condition: new, Year of construction: 2024, Discover the powerful Durma press brake at our demonstration center in Saerbeck. As a manufacturer, we offer you maximum precision and efficiency with a capacity of 3050 mm in length and 175 tons. Benefit from our comprehensive all-in-one service: We take care of transportation, installation, commissioning and offer you a one-year warranty as well as fast and reliable service. Visit us and see the quality and versatility of this first-class machine for yourself. Standard equipment Capacity (length X ton) 3050mm x 175t Installation height 530mm Outreach 450mm Stroke 265mm Y1, Y2, X - 3 axes Control unit - DT 15 Manuel F. AKAS FPSC safety system CE F.AKAS BVLT light barrier and safety cages (for tandem press brakes) Iisdettatbepfx Ab Nsb Servo motor backgauge & linear guide & Ball screw system (X) Manual crowning European style tool clamping system Sliding front arms Hydraulic block and valves in special design according to worldwide standard -Electrical equipment according to worldwide standard Selected options -Control unit - Delem 66S - NEW -Motorized crowning - X=650mm X,R, Z1, Z2 (6 axes controlled press brake) press brake) -Lower tool European M.460R.85 -European upper tool P135.75.R08