Used Homag Double Tapper Line for sale (20,640)

Condition: good (used), Year of construction: 2015, machine/vehicle number: 0-200-24-0779, functionality: fully functional, input voltage: 400 V, input current: 55 A, input frequency: 50 Hz, type of input current: three-phase, workpiece height (max.): 60 mm, edge thickness (max.): 20 mm, total length: 10,825 mm, Used single-sided HOMAG edge-banding machine for straight edges – KAL 370 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2015 EQUIPMENT / SPECIFICATION BASIC MACHINE - with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness 8 to 60 mm - top pressure with compound V-belt, automatic height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors (clockwise, counterclockwise), 2x4kW, rear motor w. jumping function GLUING SECTION V20, consisting of: - QA60 glue application unit, with PTFE-coating (Teflon), with manual quick-adjustment glue gates - pneumatic clamping of glue application in mount - Pre-melter for EVA glue - Edge magazine, edge thickness min. 0,4 mm to max. 20 mm Edge width (height) max 65 mm - modes: edge rolls, (veneer) strips, solid wood edging - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 4 non-driven pressure rollers. POST-PROCESSING SECTION: - Snipping (end-trimming) unit PK85 horizontal, 2 motors, with straight/chamfer cutting function - Rough trimming 2x1.15 kW, top/bottom - Corner rounding FK11, 2 motors (top/bottom) with various trimming heads, motorised adjustment - Universal trimming unit, (e.g. grooving), 3.5 kW, tiltable, w. electro-pneumatic jumping control - Multi-Profile (radius-) scraping MN11 with automatic positioning by NC-axis (CAN) - Flat scraping (glue joint) FA20, top/bottom, (version with 3 tracer rollers) - Buffing unit FP10, top/bottom Dedpfx Aey A I Sgsbfjuu Control / software: - powerControl PC 23 PowerTouch - woodCommander 5 Machine dimensions 1085 x 180 x 235 cm (with opened doors)

Condition: used, Year of construction: 1990, functionality: fully functional, machine/vehicle number: 2124, travel distance X-axis: 1,200 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 1,375 mm, feed rate X-axis: 20 m/min, feed rate Y-axis: 20 m/min, feed rate Z-axis: 20 m/min, spindle speed (max.): 4,000 rpm, 5-axis machine Pallet size: 800 × 800 mm Automatic workpiece change: 5 pallets CNC control: FANUC 15M Spindle: 22 kW – 4000 rpm, FANUC Axis motor (20 m/min) + drive: FANUC Tool magazine: 118 tools, type 50, DIN 69871 Dodsyzxyxopfx Abfeuu

Condition: refurbished (used), Handtmann form&hamburger line + filler FS-510 + VF-830 Dusdsxniyaopfx Abfju

Condition: used, Automatic Bag Filling Line Bag weights from 5kg to 1000kg Dujdpjyq Tb Isfx Abfou Infeed with product de-clumper / product breakup breaker and sieve. Incline screw auger to high level hopper and mixer. Delivery system to bag filler where weighing takes place and metal detection before bag filling point. This system comes with a second mobile screw auger for filling 1000kg big bag / sacks Complete with all the controls for the smooth running of this bagging line. After Bagging the bags are sealed with a Saxon Bag Sealer and then stitched with a Singer Bag Stitcher.

Condition: like new (used), functionality: fully functional, Ferwood Code: RS0003616 - Manufacturer Code: 2-083-02-7120 - Condition: As new (display item) - Functionality: Fully operational - Compatible Machine: - Weight: 2.5 kg - Dimensions: 36x26x21 cm - If interested, we offer an overhaul service; please contact us. Dusdpfsyz T Ttex Abfju

Condition: excellent (used), Year of construction: 2004, functionality: fully functional, Machine number: 559969 Manufacturer: HOMAG Model: PROFI BAZ 723/42/18/KC Year of manufacture: 2004 Dedpjxvy Ukefx Abfjuu Technical details: Weight approx.: 10000 [kg] control: PC85 [] Dimensions (l x w x h) approx.: 39000 x 3200 x 3200 [mm] c-axis: ja / yes [] software: WoodWOP [] working length x-axis: max. 4.200 [mm] working width y-axis: max. 2.075 [mm] main spindle: 2x 14,5 [kW] tool changer: 2x 18-fach / 2x 18-fold [] vacuum pump: 2x 100 [cbm/h] edge gluing unit: ja / yes 360° [] path-feed rate max. X-axis: 80 [m/min] path-feed rate max. Y-axis: 60 [m/min] path-feed rate max. Z-axis: 40 [m/min] Item Description High-End-equipped, technically well maintained HOMAG PROFI BAZ 723/42/18/KC CNC Machining Center in portal design with 360° edge glueing unit, 2 main spindle with C-axis, automatically positionable clamping consoles and HOAMG Optimat TBP 370 vacuum feeder in in portal design. The original price was approx. 620.000 EUR. Technical data and equipment of the HOMAG Profi BAZ 723 CNC: - Workpiece length for single operation max. 4.200 mm - Workpiece length cutter Ø 25 mm for pendulum operation max. 2.040 mm - Workpiece length glueing for pendulum operation max. 1.850 mm - Workpiece width (cutter Ø 25 mm) max. 2.075 mm - Workpiece width (glueing) max. 1.950 mm - Workpiece width (all aggregates) max. 1.850 mm - Console table KC-System 2 pieces left/right automatic positioning of the consoles and vacuum clamps - First main spindle with C-axis motor 14,5 KW speed 0 - 24.000 U/min tool changer 18-fold (without tools, HSK holders and aggregates!) drill head 17 spindles vertical (7 spindles X-direction, 11 spindles Y-direction) drill head 4 spindles horizontal 4-SP+Sawe 0/90 dedree blow-off nozzle pneumatically on carrier - Second main spindle with C-axis motor 14,5 KW speed 0 - 24.000 U/min tool changer 18-fold (without tools, HSK holders and aggregates!) drill head 17 spindles vertical (7 spindles X-direction, 11 spindles Y-direction) drill head 4 spindles horizontal 4-SP+Sawe 0/90 dedree blow-off nozzle pneumatically on carrier - Edge gluing aggregate 360° glue with butt joint mounted on the right side of the portal with Y-axis drive Drive spindle with C-axis edge height max. 65 mm edge thickness 0,4 - 3 mm pre-cutting station and 2-fold roller magazine - Chip conveyor belt for automatic disposal with ascending conveyor (The tools, the HSK holders and the units for the tool changer are not included within delivery. A transport rack from HOMAG is required for transportation of the dismantled machine. Terms of payment and delivery Delivery terms: ex foundation, unpackaged Payment terms: 100% before loading Warranty: Without any warranty

Condition: used, functionality: unexamined, Ferwood Code: AGG0213 - Manufacturer Code: 1-056-09-3351 - Condition: Used - Functionality: Not tested - Compatible Machine: - Weight: 8 kg - Dimensions: 46x39x27 cm - If interested, we offer an overhaul service. Please contact us. Dodpoyztt Hofx Abfsuu

Condition: used, functionality: unexamined, Ferwood Code: AGG0213 - Manufacturer Code: 2-056-10-0220 - Condition: Used - Functionality: Not tested - Compatible Machine: - Weight: 6KG - Dimensions: 36X26X21 - If interested, we offer an overhaul service; please contact us. Duodpfx Abeyztr Aofeu

Condition: like new (used), Year of construction: 2017, functionality: fully functional, working width: 1,600 mm, total length: 75,000 mm, total width: 17,000 mm, Technical Details: Cefla painting/finishing line with roller coating machines for panel finishing *Maximum working width: 1650 mm *Automatic loading system with integrated robot *Line dimensions: 75 x 17 m *Line configuration: *3 x Cefla Smartclean 32-B brush cleaning machines *3 x Cefla Smartcoater MF Evo roller coating/painting machines *1 x Cefla Smartcoater SP1 Evo finishing machine *2 x Cefla UV-R M1 1600 UV curing tunnels (1 UV lamp each) *1 x Cefla UV-R M3 1600 UV curing tunnel (3 UV lamps) *1 x Cefla UV-R M2 1600 UV curing tunnel (2 UV lamps) *Cefla TR500 motorized conveyor line Dujdpeyv Hzgefx Abfsu *Cefla automatic panel turner *Costa top sanding machine with 1 roller and 1 finishing pad *Automatic loading system with 2 x ABB robots

Condition: good (used), Year of construction: 2012, overall weight: 3,000 kg, year of last overhaul: 2025, Equipment: CE marking, - HOMAG KAL211 EDITION 2264 Year of manufacture: 2012 Duodeyz Dbbspfx Abfeu OVERVIEW OF AGGREGATE CONFIGURATION: - Control: powerControl PC22 - Top pressure with composite V-belt - Feed rate: 18 - 25 m/min - Workpiece thickness: 60 mm instead of 40 mm - Total length: 7845 mm - Electronic height adjustment FPR/L260+EDITION+FSQ - Quick-clamp system for application unit QA/PU - Separator spraying unit above/below - Jointing milling unit - Gluing station A20 with Quickmelt application unit - Magazine 2 manual, 2 rolls - Preparation for Lasertec activation unit - End trimming unit HL84 chamfer/straight - Automation package chamfer/radius AMB/EDITION2264/74 - Pre-milling unit BF10 1.5 kW - Contour milling unit FK11 manual - Profile scraper PN10 - Finishing unit - Glue joint scraper - Buffing unit - Drying box with nitrogen

Condition: used, Webomatic Mobile Double Chamber Vacuum Packer Type: CD 120-PR Dodjym U Inopfx Abfouu Serial number: 5710JL525 400 V, 3 Ph, 50 Hz, 5.0 A, 2.2 kW Seal length: (2x) 640 mm Dimensions chamber: (2x) 650 mm x 570 mm Busch vacuum pump Total dimensions: 1420 mm x 840 mm x 1060 mm.

Condition: used, Year of construction: 2003, machine/vehicle number: KL 77/A20/S2, functionality: fully functional, feed rate X-axis: 20 m/min, total length: 9,000 mm, Equipment: documentation/manual, We are offering this used HOMAG Optimat kL 77/A20/S2 EVENT edge bander, year of manufacture 2003. Manufacturer: HOMAG Model: Optimat kL 77/A20/S2 EVENT Year of manufacture: 2003 Condition: used Type: edge bander Edge bander for sale due to purchase of a new machine. The machine is currently still in use and fully operational. Dedoyw N Apspfx Abfeuu It is a very robust machine, including a return system. Very stable and always delivers a perfect finish! Equipment: - Nozzles - Format cutters, 100mm diameter - Blow-off unit - Preheating unit - PUR bonding with cartridge heating station - 7 pressure rollers - Crosscut saws, straight and mitre - Top and bottom roughing cutters - Profile cutters, radius 1/2mm - Profile/flat scrapers - Nozzles - Polishing brushes - Machine equipped with top and bottom belts (very stable design) - Height adjustable at the front (automatic) - Profile cutters automatically adjustable via the program - Crosscut saws automatic - All functions can be switched on/off via the front screen - Return conveyor operated from the PC ->Demo available upon request! Price to be discussed via private message. Please do not hesitate to contact me if you have any questions. If you have any questions or require further information, feel free to send us a message or give us a call.

Condition: good (used), Double-end tenoner, edge processing machine, scoring motor, chipper motor, spindle motor, milling motor Dodpfxjb A Nx Do Abfsuu -Power: 0.23 kW -Speed: 18000 rpm at 300 Hz -Dimensions: 210/70/H100 mm -Weight: 2 kg

Condition: excellent (used), Year of construction: 2018, Stork / Marel AMF Filleting Line AMF-i Professional Chicken Breast Filleting Line – High Efficiency and Precision We offer a complete Marel / Stork AMF-i filleting line, tailored for modern poultry processing plants. This system provides automatic and precise filleting of chicken breasts while ensuring maximum throughput and superior end-product quality. Key Benefits: Intelligent Filleting (Adaptive Filleting) The system automatically adjusts its settings to the size of the raw material, guaranteeing high-quality results and optimal yield regardless of product dimensions. High Production Efficiency Processes up to approximately 60 fillets per minute – an ideal solution for large-scale operations. Consistent Quality and Maximum Yield Losses are minimized, and efficient recovery of by-products (tendons, skin, meat) is ensured. Modular Design The line can be configured and expanded to meet individual production requirements. Process Automation Manual labor is significantly reduced, increasing consistency and process repeatability. Included Components: - Loader module - Filleting line with integrated measuring system (encoder) - Skinning module - Splitting module with automatic adjustment - Separation module - Tendon collection system - Original control cabinet Technical Specifications: Model: AMF-i Manufacturer: Stork / Marel Year of Manufacture: 2018 Capacity: up to 3,600 fillets/hour Condition: Very good / ready for operation Type: Chicken breast filleting line Dujdpfx Aox Hymdjbfsu STORK / MAREL / AMF / FILLETING LINE / CHICKEN BREAST

Condition: good (used), 1 x Carrot Line and Grader system Can also be used for potatoes, onions, beet root and brussel sprouts etc. System will be coming out of production end of May/early June. All equipment has had a full service and checked over during the spring period for the coming year. Haith Screen Bits Remover. The Screen Bit Remover continuously removes broken fragments of crop and debris from the produce flow. Carrots are transferred onto a traveling screen with a set size aperture. As the screen is conveyed forward, two full-width agitators gently move the crop causing any bits and debris to drop on to a waste conveyor below where the produce is taken over the end. The screen and agitator speeds are variably controlled individually to suit the various crop conditions. Grader / sorter Odenberg Titan 2 automatic camera grading system – installed in 2008. Titan 2 Sorter 6002.2, 3-way carrot sorter. The first sorter removes product that is not usable, damaged etc to the waste line. The second sorter removes short carrots, twisted and misshaped which are sent directly to the value tank. All the rejects go through the positive sorting area and the grading operative throws back any product that is fit for value sale. High capacity and low maintenance sorting machine Flexible sorting machine with gentle handling assured Quality control and feedback accessible through intuitive touch screen Consistent long-life accuracy. Grading Station. The grading operatives throw out any unusable product to the waste line via the positive grading area. Two to four graders can operate here depending on the quality of the produce. Wyma Lift Roller Sizing Grader – installed in 2019 The product is divided into five grades. 500g, 0-25mm, this goes to the value tank. 1kg, 25 – 42mm max. Loose min 30 – 45mm max. Lumpers, min 45mm upwards. Oversize. The Wyma Lift Roller Sizer is a diameter grader suitable for a wide range of fruits and vegetables including carrots, potatoes, parsnips, beets, citrus, onions, bulbs, brussel sprouts, rutabaga and other round or tubular products. It is extremely versatile, offering multiple size outputs at high capacity in one machine. It can cater for a large range of product sizes and shapes through a selection of different roller options. Product size ranges, or size bands, are created by adjusting the spacing between the rollers, at defined locations, along the length of the machine. The Lift Roller Sizer is made from stainless steel and food-grade plastic materials. Five Lift Roller Conveyors. All supporting framework available. *Video available on request* Dujdsv I S D Sspfx Abfeu Located in Wexford, Ireland. Buyer to collect – machinery will be dismantled and loaded to your vehicle. UKFM2-6653

Condition: used, Year of construction: 2002, Double-sided softforming edge banding machine HOMAG type Power KF 20/34/QE/30, machine no. 0-202-25-8815, year 2002 Dedpoyyxc Rsfx Abfjuu

Condition: excellent (used), C.N.C. WORKING CENTER 3 axes (X-Y-Z) Dsdpeyywcvsfx Abfsuu Vertical position of the panel (workpiece) Movable panel (workpiece), movable working head Numerical Control POWERCONTROL + POWERTOUCH Software woodWOP Safety cabin (enclosure) of the working head No. 1 Workpieces fixing clamps (for the panels introduction in the working area Panels feeding by motorized chain/track Minimum workpieces dimensions (X - Y - Z) mm 200 x 70 x 8 Maximum workpieces dimensions (X - Y - Z) mm 3050 x 850 x 56 Total installed power (Kw) 11,5 (ca.) WORKING GROUPS: No. 1 Drilling head (power Kw 2.3) with vertical spindles - No. 13 Independent vertical boring spindles (V13 High Speed) - No. 6 Independent horizontal boring spindles (4 in X + 2 in Y) No. 1 Circular Grooving Saw (on X axis) dia. (mm) 100 No. 1 Vertical electro-spindle (HKS63) power Kw 5 Automatic Tools Changing System - Tools storage plate (No. 4 folds-positions)

Condition: excellent (used), FLEXIBLE C.N.C. WORKING CENTER 3 axes (X-Y-Z) Movable panel (workpiece), static working head - Horizontal position of the panel (workpiece) Duodpjyyvttjfx Abfeu Safety cabin (enclosure) of the working head Numerical Control PowerControl PC86 power Touch (Software woodWOP) Separate electric and command cabinet No. 2 Workpieces fixing clamps (for the panels introduction in the working area) WEEKE Prepositioning Unit - to position workpieces in machine with clamp grippers faster. In-feeding working table (panel support) and Out-feeding table (with motorized belts) Minimum workpieces dimensions (X - Y - Z) mm 200 x 70 x 8 (2 x 4 mm) Maximum workpiece dimensions (X -Y- Z) mm 3000 x 1000 (option mm 1300) x 80 (2 x 40 mm) Two panels simultaneously processables (in Z axe) Separate electric and command cabinet WORKING GROUPS (TOP): 2V42, 2H8X/2Y, N2 X-Y90,F2-ETP-6 KW No. 1 Vertical electro-spindle ETP-6 (power Kw 6) No. 1 Circular Grooving Saw (90° on X-Y axe) dia. mm 125 No. 42 Vertical drilling spindles (power Kw 2.3) No. 10 Horizontal drilling spindles (8 in X + 2 in Y) WORKING GROUPS (BOTTOM) 2V42, 2H8X/2Y, N2 X-Y90,F2-ETP-6 KW No. 1 Vertical electro-spindle ETP-6 (power Kw 6) No. 1 Circular Grooving Saw (90° on X-Y axe) dia. mm 125 No. 42 Vertical drilling spindles (power Kw 2.3) No. 10 Horizontal drilling spindles (8 in X + 2 in Y)

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, Working height: 900 mm Working width: 1,350 mm Belt changing side: left Workpiece thickness: 3 - 160 mm Frequency-controlled feed speed: 4 - 20 m/min Abrasive belt dimensions: 2,620 x 1,350–1,380 mm Adjustable sanding belt blowing device with 5 settings WRD WORKPIECE CLEANING ROTOR Workpiece cleaning system with 16 rotating nozzles MOBILE OPERATING TERMINAL powerControl with powerTouch SST SOFT STARTER Inrush currents are limited to prevent voltage drops GWRD BELT CLEANING PROGRAM Upon activation, the machine automatically sets to a 10 mm workpiece thickness and activates the blowing rotors. After the feed belt is fully cleaned, the machine returns to its initial setting. AAT EXTRACTION DAMPER CONTROL Control of extraction dampers via the terminal (24 Volt DC, without extraction dampers included) UPS EMERGENCY POWER SUPPLY FOR BELT CONTROL 1-3 PCS Uninterruptible power supply for sanding belt oscillation in case of power failure System consists of: SANDTEQ W-700, PROFI SWB735/RRE – sanding from below Wide belt sanding machine with three sanding units for processing wood or wood-like workpiece surfaces Prepared to accept up to two auxiliary units, such as a cleaning brush, satinizing or structuring brush, and rotating cleaning nozzles. Units: I. R UNIT Sanding unit with automatically adjusting contact roller Profiled steel roller, 240 mm diameter With grain compensation Drive motor: 37 kW Abrasive belt speed: 25 m/s - Automatic locking of the sanding unit for fast belt changes and increased process safety - Abrasive belt drives with electronic, wear-free brake - Optical, touchless abrasive belt tracking - Pneumatic abrasive belt tensioning with integrated belt edge compensation II. R UNIT Sanding unit with automatically adjusting contact roller Rubber-coated roller, 240 mm diameter Dusdpfxjyw Ndmo Abfou Rubber hardness: 85° Shore With grain compensation Drive motor: 30 kW Abrasive belt speed: 18 m/s III. E UNIT Sanding unit for installing a pressure beam - Automatic locking of the sanding unit for fast belt changes and increased process safety - Abrasive belt drives with electronic, wear-free brake - Optical, touchless abrasive belt tracking - Pneumatic abrasive belt tensioning with integrated belt edge compensation - Protected storage area on the machine for additional sanding inserts Drive motor: 22 kW Abrasive belt speed: 2 – 18 m/s Torque-dependent standby operation to reduce energy consumption. ACP PNEUMATICALLY SUPPORTED PRESSURE BEAM - Adjustable sanding pressure via pressure regulator - Workpiece-controlled engagement and disengagement at the leading and trailing edges - Various sanding inserts, 80 mm wide, with different felt hardnesses Machine dimensions (L x W x H): 3,900 x 2,100 x 2,000 mm Machine weight: approx. 7,500 kg SANDTEQ B-700, PROFI SWT735/RRE – sanding from above Wide belt sander with three sanding units for machining wood or wood-based workpiece surfaces Units as above, additionally: FBM FINISHING BRUSH Brush unit with finishing brush Bristles: horsehair Diameter: 130 mm Drive motor: 0.75 kW Machine dimensions (L x W x H): 2,995 x 2,100 x 2,255 – 2,415 mm Machine weight: approx. 6,500 kg

Condition: excellent (used), 203018) SINGLE SIDE EDGE BANDER (Left) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Edges thickness in strips / lippings (min/max) mm 0,4 / 20 Panels thickness (min/max) mm 8 / 60 NEW (in 2024) Numerical Control EDGETEQ MOD - Power Touch (WoodCommander) Adjustable Feeding speed up to 25 m/min In-feeding system EZ 14 Spraying unit (Anti-sticking liquid) In-feed fence, adjustable by N.C. Pre-milling Unit (vertical joint trimmers) 2 x Kw 3 Dujdpsyyvp Uefx Abfou Glueing Unit (P.U.R. Glue + Quick Melt system) Band Pressure zone, adjustable by N.C. Edge coils supporting unit (with No. 2 reels) Snipping (end-cutting) unit HL 84 (2 x Kw 0,5 ca.) Pneumatic swivelling and adjustment Rough Trimming unit BF 20 (2 x Kw 1,5 ca.) Multi Function Unit (Profile contour Trimming) FK 11 (2 x Kw 0,4 ca.) Profile edge scraping unit Finish processing unit (Glue scraper + Buffing unit) FA 11 203019) Panels Return System "LIGMATECH" Mod. ZHR 541/L/095 (with Portal bridge and 360° rotating vacuum head)

Condition: excellent (used), SINGLE-SIDE EDGE BANDER (LEFT-side) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Panels thickness (min/max) mm 12 / 80 Edges thickness in stips / lippings (min/max) mm 0,4 / 20 Numerical Control NC21 Feeding speed m/min 18 Top pressure system with rubber belt In-feed fence, adjustable by N.C. Pre-milling Unit (vertical joint trimmers) 2 x Kw 3 Dsdpfel Iz Tujx Abfouu Glueing Unit (Hot Melt Glue + Quick Melt system) A20 + A34 Band Pressure zone "C" Edge coils supporting unit (No. 1 reel) Snipping (end-cutting) WK 14 (KW 0.8x2 motors at RPM 12000), pneum. adjust. chamfer/straight Rough Trimming unit Optimat (2 x Kw 1,5) Fine Trimming unit MF20 (2 x kw 0,55) Corners Rounding (contour trimming) Unit FF12 (4 x Kw 0,4) CNC (WD40) Free space for Profile Scraping unit Finish processing unit ( Glue scraper + Buffing unit) FA 10

Condition: excellent (used), PANELS RETURN SYSTEM for EDGE BANDER (LEFT SIDE) To combine with a single-side Edge Bander allowing the operator (worker) to always stay at the in-feed side of the machine (the processed workpiece will automatically return-back to him). Roller translator table with belts - 180°: 2600 mm x 1800 mm Dusdpfx Ajgz Atbsbfeu 1° Conveyor (motorized carpet) (mm) 7000 x 900 2° Conveyor (motorized carpet) (mm) 2500 x 850 Mod. BOOMERANG BONSAI

Condition: excellent (used), Gantry (Portal) machine Movable panel (workpiece), movable working head (Horizontal position of the panel/workpiece) Numerical Control Power Control, Software WoodWOP Safety cabin (enclosure) of the working head and integral safety cabin (enclosure) of the machine In-feeding working table (panel support). Out-feeding working table (panel support) Panels (workpieces) feeding by No. 3 motorized belts - Feeding speed (m/min) max 130 ca. Minimum workpieces dimensions (X - Y - Z) mm 250 x 100 x 15 Maximum workpieces dimensions (X - Y - Z) mm 2500 x 1050 x 60 Motorized carpet to evacuate chips and wastes. Separate electric and command cabinet Total installed power: Kw 99 N° 2 WORKING GROUPS (TOP) - (SERVO-MOTOR X-Y-Z ): N° 4 Drilling heads (4 x Kw 2.3) with No. 10 vertical spindles each (total top spindles No. 40) Dodpfxegwbbqe Abfeuu N° 3 WORKING GROUPS (BOTTOM) - (SERVO-MOTOR X-Y-Z ) : N° 6 Drilling heads (6 x Kw 2.3) with No. 40 vertical spindles each (total bottom spindles No 240) N° 2 WORKING GROUPS (HORIZONTAL) N° 2 Drilling heads with horizontal spindles N° 21 Horizontal drilling spindles (Right Side) + N° 21 Horizontal drilling spindles (Left Side) N° 8 Dowel Inserting nozzle & glue injectors(Right side) + N° 8 Dowel Inserting nozzle (Left Side) N° 2 Storage tanks for automatic feeding of the dowels OPTIONAL: WIRELESS BAR CODE SCANNER

Condition: excellent (used), TURNING DEVICE FOR PANELS (LONGITUDINAL TO CROSS) Equipment to be placed between two Double End Tenoners (or two double-side Combination machines) in a line (straight position) or before an independent Double End Tenoner (or double-side Combination - Sizing & Edge Banding machine) To turn at 90° panels (workpieces) from longitudinal sense (lenghtwise) to cross sense (crosswise) Built-in electric and command panel Djdpfjd Siydox Abfeuu Total length mm 6200 1st Table (longitudinal) with motorized rollers mm 1300 x 3200 (ca.) Motorized turning device, with double cone (1 top + 1 bottom) 2nd Table (cross) with motorized rollers mm 2500 x 3000 (ca.) Min dimensions of the panels mm 195 x 250 Max dimensions of the panels mm 1200 x 2500 Min/Max panels thickness mm 12 - 40 Total installed motor power Kw 3

Condition: excellent (used), "SOFTFORMING" SINGLE-SIDE EDGE BANDER - Min/Max edges (band) thickness in rolls mm 0,3 - 3 - Min/Max edges thickness in strips/lippings mm 0,4 - 12 - Min/Max panels thickness mm 12 - 60 - Numerical Control: Power Control PC 22 Dsdpefd Ilyofx Abfsuu - Feeding speed (adjustable) m/min 12 - 24 - Top motorized pressure belt - Free Space: mm ? - Glueing Unit (Hot Melt + Quick Melt System): QE 34 / E12 - Pressing Roller (Revolver) both for straight edges and shaped edges (Softforming) - Edge coils supporting unit, with N. 1 coil - Snipping Unit HL 84 (2 x Kw 0.84 at RpM 12000) - Rough Trimming unit (2 x Kw 1.5 at RpM 12000) - Fine Trimming Unit (2 x Kw 0.4 at RpM 12000) 0°-30° OPTIONAL: Infeeding system, with extended infeed fence and 3 top motorized rubber wheels