Used Gm Gera Gm Gera Nagema Arcade Ds 03/85/24 Bottle Washer for sale (23,416)

Condition: used, Year of construction: 1993, Overview The GM Gera NAGEMA Arcade DS bottle washer was previously used in a brewery. There it was operated in single-shift operation. Since the sales volume has decreased, the beer of the brewery is now bottled at another location and this bottling line has become available. Due to the low number of operating hours and regular maintenance, the machine is in a very good condition. All basins and the machine body are made of stainless steel. Spare parts, such as bottle cells, are also still available. Furthermore, the main drive shaft, as well as the motor and gearbox were overhauled by SEW in 2018 and the carrier chain was replaced in 2015. The machine is still mounted and can also be demonstrated. Tech Specs: Capacity: 23,000 bph Cell pitch: 85 Bottles per row: 16 Dimensions + weights with attachments: 8640 x 4470 x 1920 mm / 17,900 kg Details: Standard drives Heating with steam Operating side left CE certified Chemistry dosing pumps Machine data sheet Fixed pipe spraying controlled by machine cycle Single-end machine Label discharge rear right Finger discharge + finger feeding Bottle discharge left Bottle cells plastic HMI Lauer Lye concentration measurement 24 Volt control voltage Control S5 (on request conversion to S7) Regularly maintained Water part in VA Fume extraction Sampling taps KSB pumps in VA Plug-in strainers for baths Water meter Conductivity measurement from Endress Additional Equipment: Spare parts included   Lhjdpfx Aiel Hx Adeqsl

Condition: used, Year of construction: 2024, Overview Lhsdpfxovrfive Aiqsl The bottle washer was previously used in a brewery. Due to the low number of operating hours, the machine is in very good condition, like new. It was replaced, as the previous owner wanted to run bottle formats, which did not fit this machine. All basins and the machine body are made of stainless steel. The machine is already disassembled and dry stored, so that it can be easily loaded and transported. The machine comes with 12months warrantee. Tech Specs: - Capacity: 9,500 bph - Cell Pitch: 95 mm - Bottles per row: 25 - Dimensions + Weights: Housing: 7,162 x 2,740 x 2,500 mm / 18,806 kg Ready for operation with attachments: 7,162 x 3,540 x 2,730 mm / 31,563 kg - YOM 2024 - Formats: - 0,25l - 0,33l - 0,5l - 0,75l The Machine in Detail / Equipment Features: - Heated by steam - Pre Cleaning and removal of residual liquids by pulsed rinsing prior to washing - CE certified - Chemical Dosing Pumps - Machine data sheet included - High pressure pre rinsing - Rotating Spray nozzles - Single End Machine - Label discharge rear right - Finger discharge + finger feed - Bottle cells made of plastic - Concentration measurement - NaOH supply liquid - Sectional view arrangement of baths - Spindles SST - 24 volt control voltage - Control Siemens S7 - Regularly maintained - Full machine body in SST - Vapor Discharge - Machine dismantled, ready to ship - Automated machine Startup

Condition: used, Year of construction: 2010, Overview   This ARCADE GEL 6 bottle washer was built in 2010 by the German manufacturer GM Gera. The machine is still in operation and can be inspected in person at any time. The ARCADE GEL 6 is fully functional and must be replaced due to an increase in performance.   Technical details   Nominal output: 33,000 bph   Control range: 13,200 - 36,300 bph   Chain pitch: 169 mm   Cell pitch: 110 mm   Bottle cells per row: 30 pieces   Total bottle cells: 7,860 pieces   Bottle cells, loaded: 7,680 pieces   Consumption  Compressed air: 1m³   Steam (operation): 489 kg/ h   Steam (heating): 4,430 kg/ h   Electrical power: 48.4 kW   Water: 7.35 m³/ h   Bath volume   Pre-soak: 2,263 l   Pre-caustic: 7,240 l   Caustic 1: 31,755 l   Caustic 2: 350 l   Hot water 1: 350 l  Hot water 2: 350 l   Cold water: 350 l  Ljdet Ul Exopfx Aiqohl

Condition: used, Year of construction: 1999, Overview The bottle washer was previously used in a brewery. Due to the complete reconditioning in 2005 and continuously maintentance, the machine is in very good condition. All basins and the machine body are made of stainless steel. The machine is already disassembled and dry stored, so that it can be easily loaded and transported.  Tech Specs: - Capacity: 6,700 bph - Cell Pitch: 102 mm - Bottles per row: 10 - Dimensions + Weights: Housing: 7,200 x 1,300 x 2,850 mm / 13,500 kg Ready for operation with attachments: 7,790 x 3,450 x 2,950 mm / 20,000 kg - YOM 1999 - Formats: - 0,33l - 0,5l The Machine in Detail / Equipment Features: - Heated by steam - Pre Cleaning and removal of residual liquids by pulsed rinsing prior to washing - CE certified - Chemical Dosing Pumps - Machine data sheet included - High pressure pre rinsing - Rotating Spray nozzles - Single End Machine - Label discharge rear right - Finger discharge + finger feed - Bottle cells made of plastic Lhjdpfx Aijwg E D Ijqel - Concentration measurement - NaOH supply liquid - Sectional view arrangement of baths - Spindles SST - 24 volt control voltage - Control Siemens S7 - Regularly maintained - Full machine body in SST - Vapor Discharge - Machine dismantled, ready to ship - Automated machine Startup

Condition: used, Year of construction: 2005, Overview The bottle washer was previously used in a mineral water factory. Due to the good maintenance, the machine is in good condition. All basins and the machine body are made of stainless steel. The machine is still working and will be free in early 2027, when the complete line is replaced. Lhsdpfx Aiezbha Heqsl Tech Specs - Capacity: 15,500 bph - Cell Pitch: 95mm - Bottles per row: 16 - Dimensions + Weights: Housing: 8350 x 1,860 x 2,990 mm / 21,750kg Ready for operation with attachments: 8,700 x 3,560 x 3,330mm / 37,639kg - YOM 2005 - Formats: - 0,5l - 0,75l The Machine in Detail / Equipment Features - Heated by steam - Pre Cleaning and removal of residual liquids by pulsed rinsing prior to washing - CE certified - Chemical Dosing Pumps - Machine data sheet included - Rotating Spray nozzles - Single End Machine - Label discharge rear right - Label press mounted to the machine - Finger discharge + finger feed - Bottle cells made of plastic - Concentration measurement - NaOH supply liquid - Sectional view arrangement of baths - Spindles SST - Control Siemens S7 - Regularly maintained - Full machine body in SST - Vapor Discharge

Condition: used, Year of construction: 2012, Overview This returnable glass bottling line consists of equipment from KRONES, KETTNER, GM GERA, RINK, SYSCONA, MATEC, FALTERBAUM, Bohrer and further supporting manufacturers. The line is designed for the processing of returnable glass bottles in crates, mainly in 0.33 L and 0.75 L formats. It includes the key process steps from crate depalletizing, crate sorting, bottle decapping, unpacking, bottle washing, empty bottle inspection, filling and screw capping to labelling, full bottle inspection, crate packing, crate inspection and palletizing. The existing crate depalletizer and palletizer are available on site; however, due to their age and outdated technology, it is recommended not to include this unit in the line acquisition. Instead, suitable modern depalletizing equipment can be offered and integrated into the line concept according to the buyer’s requirements. The line has a nominal filling capacity of approx. 18,000 bottles per hour and the premix system rated at 22,000 L/h. The line is scheduled for dismantling in February 2027. Technical Data - Line type: Returnable glass bottling line - Application: Beverage filling in returnable glass bottles - Formats: 0.33 L and 0.75 L glass bottles - Packaging: Bottles in crates - Filler capacity: 18,000 bottles/hour - Premix capacity: 22,000 L/hour - Closure type: Plastic screw caps - Labelling: Wet glue labelling, 2 aggregates - Main machine years: 1996 – 2016 - Dismantling planned: February 2027 Scope of Delivery - Crate Depalletizer | Existing unit on site; not recommended for takeover due to outdated technology. Suitable replacement equipment can be offered and integrated - Crate Sorting System | Syscona | Expert KSA | Sorting on 2 lanes: good / bad | 2014 Lhedoza Tx Sjpfx Aiqjl - Crate Decapper | RINK | KM 690/4K | 2012 - Crate Unpacker | Kettner | Robot Junior RA3/C-T | 1996 - Bottle Washer | GM GERA | ARCADE GEL3 FV1-186/95-16 | 2005 - Crate Washer | Bohrer | R 30 | Crate washing machine | 2011 - Empty Bottle Inspector | Krones | Linatronic | 2014 - Filler / Screw Capper | Krones | Volumetic / Modulfill | 2012 - Labelling Machine | Krones | Universella | 2012 - Closure Inspection | Syscona | Expert FHK | 2016 - Inspection System | Krones | Checkmat 731 | 2012 - Crate Packer | Kettner | 1996 - Crate Inspection | Krones | Checkmat 708 | 2011 - Palletizer | Matec | Rotomat 3B | 2002 - Falterbaum | 20000TD | Premix system; capacity 22,000 L/h | 2000

Condition: used, Year of construction: 2007, Cleaning machine, manufacturer GM Gera, model: Arcade GEK2.1RV1, for 4,000 bottles/hour, 9 bottles/row, for 0.5 l NRW bottle, cell pitch 95mm, with pre-diverter, caustic bath 1+2, hot water bath 1+2, cold and fresh water spraying. Contact us for further information. Lsdpfx Aexghnaeiqehl

Year of construction: 2007, condition: ready for operation (used), A GM Gera bottle cleaning system is available. Throughput capacity with 1l PET bottles: 13000 bottles/h, bottle cells: 3240 pieces, cells per basket row: 18, cell pitch: 110mm, chain pitch: 169mm, total treatment time: approx. 15min, total immersion time: approx. 7.5min, housing material: stainless steel (SST). System dimensions X/Y/Z: approx. 8900mm/4200mm/3350mm, weight: approx. 23650kg, operating hours (09.2025): approx. 14300h. Documentation available. An on-site inspection is possible. Expected to be available from mid-March 2026. Ledpfx Aisxfbczoqohl

Condition: used, Year of construction: 2003, Cleaning machine, manufacturer: GM Gera, type: Arcade, for 24,000 bottles/h, adjustable range 7,600 – 26,400 bottles/h 25 bottles/row Lhsdpfxjyzdq No Aiqsl basket pitch 95 mm, chain pitch 140 mm with Siemens S7 control system dismantled, available for inspection at warehouse

Condition: used, Year of construction: 2012, Overview The Krones, Gera, Joha, Markl, Miho filling line for returnable glass bottles was previously used to fill beer in a brewery in southern Germany. Technical Specifications - Output: 7,800 bph - Producs: Beer and CSD - Formats: - NRW 0.5 l - 0.33 l ring neck - 0.25 l LN Machine List  - Machine type: Decrater Ledpfxoyb Sbuo Aiqjhl - Manufacturer: BMS - Year of manufacture: 2012 - Machine type: Decapper (Screw Cap) - Manufacturer: Rink - Decapping in the crate Euro 0,5l in 4x5 crate - Year of manufacture: 2012 - Machine type: Bottle washer - Manufacturer: Gera - Year of manufacture: 2024 - Machine type: Empty bottle inspector - Manufacturer: Krones - Model: Smarttronic - Incl. Pusher - Year of manufacture: 2012 - Machine type: Filler - Manufacturer: Kosme - Model: Isofill G 28/960 - 28 Valves - Year of manufacture: 2012 - With Combi Capper 4 heads(Crown Cork and Screw Cap) - Capacity: - 7,800 bph - Machine type: Labeling machine - Manufacturer: Krones - Model: Robusta - Refurbished in 2012 - 10 Bottle plates - 2 Label stations with 4 grippers and 4 glue pallets - Inkjet printer - Machine type: Crater - Manufacturer: BMS - Year of manufacture: 2012 - Crate format: Modul Crate 4x5

Condition: reconditioned (used), functionality: fully functional, Year of construction: 1979, operating hours: 216 h, Twin-screw extruder, parallel Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 85 Year of manufacture: 1979/2022 Machine no.: 85-399 Screw geometry: for PVC-hard profiles Lhedpfxjyhcc Ae Aiqol Screw diameter: 2 x 85 mm Screw length: 17 x D Screw speed: max. 30 rpm Screw torque: 10000 Nm Motor power: 3.3 - 25.0 kW Drive motor: commutator motor Elektra Faurndau Cylinder heating/cooling zones: 4/2 (air cooling with fan) Tool heating zones: 8 Temperature control: 12 x digital temperature controllers (PMA KS40) Accessories: Melt pressure sensor and melt temperature sensor Connected load: approx. 60 kW (without tool) Extrusion height: 1100 mm Output capacity: approx. 150 - 180 kg/h for PVC-hard profiles Accessories: Material hopper and connection flange Accessories: Vacuum pump (1.1 kW) incl. material separator Dimensions: 4500 x 1200 x 2100 mm (LxWxH), incl. material hopper Weight: approx. 4000 kg Note: The electrical control cabinet was completely renewed approx. 3 years ago. Since then, the extruder has only been in operation for 216 hours. Condition: The extruder was repainted (light gray, RAL 7035) and checked for function.

Condition: used, Winterhalter GM 85 – Advanced Vegetable Washer Boost your kitchen efficiency with the Winterhalter GM 85, the ultimate solution for professional vegetable cleaning. Designed for restaurants, catering services, and commercial kitchens, this machine ensures hygienic, fast, and energy-efficient washing of all types of vegetables. Key Features: - High-Capacity Cleaning: Handles large volumes of vegetables quickly, reducing prep time. - Gentle Yet Effective: Removes dirt and residues without damaging delicate produce. - Energy & Water Efficient: Optimized systems minimize water and electricity consumption. - User-Friendly Interface: Intuitive controls make operation simple for all staff. - Durable Construction: Built from high-quality stainless steel for long-lasting performance. - Hygienic Design: Easy to clean, ensuring compliance with food safety standards. Whether you need to prepare leafy greens, root vegetables, Lsdpeyudlfefx Aiqjhl or fresh herbs, the Winterhalter GM 85 delivers spotless results every time.

Condition: used, Year of construction: 2007, Overview This KHS Innoclean single-end bottle washer for returnable glass bottles was built in 2007. It cleans and de-labels empty bottles before filling: bottles are pushed into carrier-basket cells, run on heavy roller chains through a pre-soak, two pre-warming baths, the main caustic soak with under- and over-caustic label flushing, and three water spray zones, then handed back onto the bottle conveyor at discharge. Nineteen bottles run across the machine width in 4,275 cells; output range and design output are given below under Technical data. At design output, total dwell time is 18.7 minutes, including 10.8 minutes of caustic contact. KHS modernised the drive and operator station in 2022: Triple-i-Drive and a capacitive multi-touch panel with RFID login, detailed under Equipment. A KHS manual supplement dated November 2022 covers the upgrade. Technical data - Manufacturer: KHS - Model: Innoclean - Machine type: single-end bottle washer (soaker) - Year of manufacture: 2007 - Drive and control modernisation by KHS: 2022 - Output range: 2,800 - 14,500 bottles/h - Design output: 13,200 bottles/h, 0.75 l glass bottle, 0.68 kg - Bottles across machine width: 19 - Carrier baskets: 225, of which 217 loaded - Cell pitch: 105 mm; carrier chain pitch 169 mm - Bottle diameter: 54.0 - 89.5 mm (plastic cells) - Bottle height: 180 - 340 mm - Bath volumes: main caustic soak 23.0 m³, pre-soaks 0.9 and 1.1 m³, after-caustic 0.3 m³, spray zones 0.4 m³ each - Power supply: 400 V, 50 Hz, TN-S, 113 A nominal, 125 A slow fuse; control voltage 24 V DC - Water consumption: 3.56 m³/h, 270 ml per bottle - Compressed air: 1.0 Nm³/h at 3 bar - Overall dimensions: 11,040 x 4,470 x H 3,438 mm (incl. infeed table) - Conveyor heights: infeed 720 mm, discharge 1,690 mm - Weight approx.: 33.5 t machine, 62.6 t operating - Largest transport segment: 4,410 x 4,100 x 3,370 mm, approx. 7.3 t - Enclosure type 12; CE marked Equipment - Triple-i-Drive: worm gearboxes with individual geared motors, each on its own servo inverter with synchronisation and individual overload protection - Servo-driven infeed and discharge segments with brake motors - Capacitive multi-touch operator panel, graphical interface with component views, RFID card reader - Gearbox monitoring with torque protection - Two pre-warming and main caustic immersion baths, with under- and over-caustic label flushing and bottle base spray-off - Automatic label discharge over a full-width sieve belt with brush take-off - Automatic level control and caustic dosing; sieve tub filtration and after-caustic circuit for long caustic service life - Three water spray zones, internal and external, with rotating fresh-water spray - Vapour extraction and plate heat exchanger - Siemens SIMOTION D and SINAMICS drive cabinet Lhjdpfx Aiezzz Iveqsl - Original KHS documentation: operating manual, 2022 supplement, spare parts list Condition Used, technically complete. Still installed and under power at its production site; photographs and video show it running. Availability Immediately. The machine will be dismantled and relocated to Germany. Viewing by arrangement; dismantling, loading and transport can be quoted on request.

Year of construction: 2018, condition: used, A washing machine for cleaning glass bottles prior to beverage filling. The soiled empty bottles are loaded into bottle baskets and pass through the system for approximately 14 minutes. First, the bottles pass through a pre-soaking bath and a lye bath in the lower section, and are then rinsed in the upper section with lye, twice with hot water, cold water and finally fresh water. The cleaned bottles are discharged onto the bottle conveyor above the bottle inlet. Additional title: single-ended machine for cleaning glass bottles Nominal capacity: 33000 Fl/h ; mechanical control range: 13.200 - 36.000 Fl/h Number of basket holders: 269 pcs. ; of which 259 were filled – total number of bottles: 7.770 pcs. Processing time: 14,14 min Heating / Cooling: 1.352.712 kJ/h Water: 7,92 m3/h Formats: 0,5 l NRW bottles Material: housing from stainless steel Lodpjzizyzsfx Aiqohl Position: in a cabinet on legs with an enlarged surface area Base construction: sinle-ended machine Features: pre-soaking and lye baths; spray nozzles; bottle conveyor with drives; pumps; top surface serving as a work platform with guardrails; housing; control cabinet; touchscreen display serving as an HMI panel

Condition: used, Year of construction: 1995, Overview The bottle washer "Sirio 7" from the German manufacturer MAG was built in 1995. Maintenance was carried out regularly by MAG. The machine can be inspected and tested in person. Technical details  Capacity up to 7,000 bph Bottle cells for 1.0 liter bottles (smaller bottles can also be used, but additional insertion plates are required) Diameter of bottles: 78 - 90 mm Bottle height: 288 - 310 mm Bottle cells per row: 10 Dimensions (LxWxH): 7,880 mm x 3,045 mm x 3,325 mm Empty weight: 14,300 kg Full load weight: 25,600 kg Installed power: 20.85 kW Heating system: Steam 3 bar Lhedpfx Aiotrbrqjqel

Condition: used, Year of construction: 1995, Overview  Ledpfx Aiovl Huaoqjhl This bottle washer was built in 1995 by Swiss manufacturer PAC. The machine is out production and be viewed in person in our warehouse. Techn. Details - Capacity:  - 6,000 bph - Min/ Max: 3,000 bph – 6,300 bp - Bottle type: 0,5L, Euro, NRW, incl. Set of parts for 330ml vichy bottle - Bottles per row: 12 - Bottles in the machine: 1,080 - Bottle cell carriers: 96 - Dimensions:  - Length: 6,000 mm - Width: 1,545 mm - Height: 2,175 mm (without feet) - Weight: approx. 5,800 kg - Water consumption: 3,6 m³/h - Heat consumption 80°C: 480 kJ/ h x 1000 - Electrical consumption: 11 kW - Incl. Spare parts - Motors for rear and front drive - Bottle cell carriers - Wear parts - Machine body fully in stainless steel - All hot zones with 5cm insulation - Label extraction belt - Heat exchanger in stainless steel for low pressure steam 116°C-120°C at 0,7 - 1 bar - Self cleaning spray tubes in stainless steel

Condition: used, Year of construction: 1996, Overview This bottle washer was built in 1995 by Swiss manufacturer PAC. The machine is still in production and be viewed in person. Techn. Details   Capacity:  10,000 bph Min/ Max: 5,000 bph – 13,000 bph Bottle type: 0,5L, Euro, NRW Bottles per row: 10 Bottles in the machine: 1,980 Bottle cell carriers: 204 Dimensions:  Length: 8,100 mm Width: 1,395 mm Height: 2,300 mm (without feet) Weight: approx. 9,210 kg Water consumption: 4,0 - 4,8 m³/h Heat consumption 80°C: 700 - 840 kJ/ h x 1000 Electrical consumtion: 17 kW Incl. Spare parts Motors for rear and front drive Bottle cell carriers Wear parts Ljdeu H R Nnepfx Aiqshl

Year of construction: 2024, condition: ready for operation (used), Nominal output: 9500 bottles/h (based on 0.5 litre NRW bottle, 68x260mm, 370g), mechanical control range: 3800-10,450 bottles/h, cycle time: 9.47s, total bottle cells: 3375, filled: 3175, per row: 135 basket rows, cell pitch: 95mm, chain pitch: 140mm, drive lanes: 3 lanes, discharge lanes: 3 lanes. Total throughput time: 21.32min, total immersion time: 7.24min, caustic immersion time: 5.34min, caustic filling time: 7.05 min, caustic contact time: 9.91min, total rinse time: 123s, total spray time: 47s, water consumption: 2.61m³/h, 275 ml/bottle, heat consumption (operation): 721. 715 kJ/h = 172,247 kcal/h, 75.97 kJ/bottle = 18.1 kcal/bottle, heat consumption (heating): 2,880 MJ = 687,467 kcal, total installed power: 27.2kW, pump power: 20.4kW, drives: 5.7kW, compressed air consumption (at 6bar): 0.2m³/h, dimensions housing: 7162x2740x2500mm. Overall dimensions: 7162x3540x2730mm, minimum access opening (W x H): 3840x2000mm, minimum ground clearance: 75 ± 25mm, height of infeed/outfeed: 645/1165mm, empty weight: 11,680kg, operating weight: 31,563kg, floor load: 8690kg/m², load per spherical base: 2130kg, number of spherical bases: 12. The machine has been running for approx. 6 months, so it is almost as good as new, including documentation. An on-site inspection is possible. Lhsdpewb E S Isfx Aiqsl

Condition: used, Year of construction: 2013, Overview The bottle washer was manufactured by the German company Krones in 2013 and put into operation in 2014. It has been serviced annually. In addition, tenside lye cleaning and spare parts can still be purchased. DISMANTLING INCLUDED. Technical data  Capacity: 66,000 bph Maximum bottle diameter 69 mm Set up for the following formats:  Vichy 0,33l Long-Neck 0,33l Long-Neck 0,5l NRW 0,5l  Steinie 0,33l Lodpfx Ael Hx Eneiqshl

Condition: used, Year of construction: 1993, Overview This Klinger BC 16/1 bottle washer was manufactured in 1993 by the german manufacturer Klinger and is designed for cleaning returnable glass bottles. The machine is made entirely of stainless steel and equipped with modern cleaning, dosing, and control features ensuring reliable operation and excellent hygiene results. The washer is in good working condition. Suitable for multiple glass bottle formats used in beverage filling lines. Technical Data Lhsdpfxsyb Sxaj Aiqjl - Manufacturer: Klinger - Type: BC 16/1 - Year of manufacture: 1993 - Application: Returnable glass bottles - Material: Full stainless-steel construction - capacity: 20.000 bottles/h Features - Complete stainless-steel construction - Steam extraction system - Finger infeed and finger discharge - Chemical dosing system - Rotating spray pipe system - Lauer control panel - Conductivity measurement - Stainless-steel filter inserts - Plate heat exchanger - Compatible with standard bottle formats

Year of construction: 2007, condition: used, A single-ended machine for cleaning glass bottles, with labels removed via a chain. The cleaning solution is steam-heated. Additional title: Single-ended machine Capacity: 17000 bo/h Weight: 26400 kg Lhedpfx Aszg I Efjiqel Machine partitioning: chain division: 110 mm Operation / Control: Simatic S7

Condition: used, Bottle washer, make Krones, type: KES 1-5-190/14-110 R, single-end machine in stainless steel, for 13.200 bph, 14 Lhodpfxsrxuv Aj Aiqjl bottles/row, with 110mm cell pitch, with pre rinsing, presoak bath, caustic soaking and caustic spraying, 4 water spraying (2x warm + 1x cold + 1x fresh water), with headboard disinfection, S7 control, built 1996. L: ~12.500 mm, W: 4.645 mm, H: 3.500 mm, weight: 33.000 kg

Condition: used, functionality: fully functional, Year of construction: 2023, operating hours: 13,979 h, machine/vehicle number: A3231E0532, controller manufacturer: Siemens, controller model: Sinumerik 840D SL, laser type: fiber laser, laser source manufacturer: TRUMPF, laser source model: TruDisk 24001, laser hours: 4,541 h, laser power: 24,000 W, laser wavelength: 1,030 nm, sheet thickness steel (max.): 60 mm, sheet thickness stainless steel (max.): 60 mm, sheet thickness aluminum (max.): 40 mm, sheet thickness brass (max.): 12 mm, sheet thickness copper (max.): 16 mm, table length: 3,000 mm, table width: 1,500 mm, working length: 3,000 mm, working width: 1,500 mm, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, workpiece weight (max.): 1,800 kg, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, TRUMPF TruLaser 5030 fiber (L76), 24 kW (2023) High-spec 2D fiber laser cutting machine, one owner from new. 3000 x 1500 mm working area. Siemens Sinumerik 840D SL control with 21.5" multi-touch display. In daily production and under TRUMPF maintenance contract from new. Key data Machine No.: A3231E0532 Year of manufacture: 09/2023 Laser source: TruDisk 24001 (external, separate energy supply) Laser power: 24,000 W Working area: 3000 x 1500 mm Max. sheet thickness (thick-sheet package fitted): mild steel 60 mm / stainless 60 mm / aluminium 40 mm / copper 16 mm / brass 12.7 mm Max. simultaneous speed: 280 m/min Machine weight: 7,650 kg Supply: 400 V 3~ / 50 Hz, 22.0 kVA, 3 x 63 A Hours: 13,979 h operating / 4,541 h laser-on Machine Box frame. Gantry drive with linear direct drives. Longitudinal conveyor belt. Transverse conveyor belt with tipping container (right). Process cooler for machine and laser (water/air). Work area illumination. Pilot laser. Spraying equipment. Automatic nozzle cleaning. Closed beam guidance via laser light cable (LLK). Machine status light. Integrated electrical cabinets. Mild steel slats, 67 mm spacing. Slag cart under pallet changer. Cleaning brush. Cutting unit Single cutting-head strategy. Protective glass with online condition checking. Dynamic Focus Control. Automatic nozzle centring. Universal cutting unit with fully adaptive lens system. Control and software SINUMERIK 840D SL. Integrated technology data. Production plan. Multi-sheet processing. Condition Guide. Cutting Guide. Quick post-production. Auto-shutdown. Programmable cutting gas / pressure selection. Microweld. Nanojoints. Oseon Go. Online Update Manager. Remote support interface. Functions and cutting packages AdjustLine, BrightLine fiber, ControlLine, DetectLine, Drop&Cut, FastLine, FlyLine, FocusLine, NitroLine, PierceLine, PlasmaLine, Smart nozzle automation. Integrated camera for process viewing. Fusion cut performance package, Highspeed cutting package, Highspeed Eco cutting package, cutting package for thick sheets, copper cutting package, brass cutting package, gas mix cutting package (N2/O2). Gas Witt gas mixer unit with hardware gas mixer for two gases, plus additional cutting gas connection. Pallet changer / automation Automatic heavy-duty pallet changer in longitudinal direction. LiftMaster Compact interface prepared; loading automation not fitted. Safety and extraction CE marking, EC Machinery Directive. Light barriers. Enclosed protective housing with certified door viewing panels left and right. Electrical rolling roof. Multi-chamber compact dust extractor. Data transfer USB interface. RJ45 network interface. Central Link. Remote support. Installation Ljdszz Sd Uspfx Aiqohl Currently installed on a mezzanine. Mezzanine steel structure not included in the sale. Condition and availability One owner from new, used in daily sheet metal subcontract production in Braintree, Essex. Under TRUMPF maintenance contract from new (two services per year) and still covered - full service history available. Can be viewed cutting under load on any working day by appointment; cut tests welcome. Offered ex works, decommissioned by TRUMPF-certified engineers and loaded onto your transport. Export packing available on request. Enquiries Full TRUMPF order confirmation, service history, hours report, cut samples and video of the machine running available on request.

Condition: used, Year of construction: 2002, Bottle washer, make Krones, type: Lavatec KESK 245/17-120, control range 4.000 - 11.000 bph, for bottles with max diam. 105mm, built 2002, single-end machine, 180 rows of 17 bottle pockets, removed label outfeed in bin, with pre-soak bath water + caustic, 1+2 caustic jetting, 1+2+3 water jetting hot+cold+fresh, for sale. Lhsdjrxup Sspfx Aiqel

Condition: used, Year of construction: 2000, operating hours: 15,800 h, Used Bottle Washer KLINGER up to 9600 bph This Bottle Washer handles up to 9,600 bottles per hour. The machine features 20 bottles per row, ensuring a long soaking time and double lye pumps. Constructed entirely of stainless steel, this bottle washer uses a Siemens S7 control system, ensuring reliable and precise operation. Technical Specifications of the Washing System The Used Bottle Washer KLINGER up to 9600 bph includes double heaters and overflow pumps, providing a high cleaning capacity. Consequently, this configuration treats each bottle uniformly, enhancing the efficiency of the washing process. The Siemens S7 control system, furthermore, offers a user-friendly interface via a touch panel, simplifying operational management. Potable Water Treatment Plant Potable water treatment plays a crucial role in the proper functioning of the bottle washer. Hager + Elsässer provides the plant, which includes cation and anion exchangers, a salt container, a pre-filter, and a UV probe. This system processes 5 m³/h, ensuring high-quality water. Additionally, the reverse osmosis (RO) plant delivers a total desalination capacity of 2.5 m³/h, ensuring pure water for the washing process. Electrical Configuration and Control Panels This Bottle Washer features three electrical panels, arranged from left to right, with a Siemens touch panel for centralized control. This configuration allows for accurate monitoring and optimal operational management. In addition, the upper panels handle cooling, with a total residence time of 4.13 minutes and a treatment time of 1.63 minutes. Technical details Bottle cells: width and diameter: height 100 mm. 360 mm spray hole in the base of the cell diameter 20 mm. The bottle cell is not round on the lower insertion side, but flattened , so that even bottles with small diameters can be inserted into the cell without any problems. Bottles from 200 ml to 1,500 ml can be rinsed. The diameter of the bottle mouth must not be smaller than the spray hole in the bottom of the cell, i.e. at least 20 mm. If the bottles are very light, or made of PVC, the spray pressure of the pumps could be reduced using software, so that the bottles are not sprayed out of the cell. Fort PVC bottles the diameter of the bottles should not be smaller than 50 mm, depending on the shape and weight. The higher the weight, the better… PVC bottles do not cause problems because of their shape or diameter, but are usually too light… So your bottles can be easily worked. Treatment and Spraying Details of the Used Bottle Washer KLINGER up to 9600 bph The central panel, on the other hand, manages the spraying times with the following specifications: Ledpfxjxqmrfe Aiqjhl Spraying soda: 0.5 min. Residual soda: 0.83 min. Hot water: 0.38 min. Warm water: 0.38 min. Cold water: 0.38 min. Fresh water: 0.