Used Mütek Map 750 for sale (4,620)

Condition: good (used), Used machine, good condition. Delivery time appr. 16 weeks after ordering Basic machine starts at 139.700 € net *Options at additional cost, see below Briquetting press e.g. for wood dust, spelled husks, activity material (e.g. for pigs to play and nibble around), animal feed, lucerne or wood shavings. *Optionally, short briquette tablets can be made Technical specifications: Throughput capacity up to a maximum of 750 kg/h (depending on the material) (e.g. sawdust with a bulk density of 250 kg/qbm) An exact statement about the throughput is only possible after a test with your material. Can vary greatly depending on the bulk density of the starting material. Goods tariff number: 84793010 Briquette Ø 65 mm including 2 m press channel Engine power main engine 37 kw Feed screw geared motor 2.2 kw Compressor screw 5.5 kw Hydraulic pump motor 0.37 kw Total connection value: approx. 47 kW Control panel with plain text display for operating states and utilization indicator for the main drive and feed screws PLC control with operating hours counter in the control cabinet Machine has CE mark Automatic start-stop function Dimensions 3100x860x1800 mm lxwxh Weight 3800kg Options at extra cost: Temperature control unit for the pressing tools to maintain the temperature for optimal briquette quality. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - absolutely necessary for operation including the corresponding control + €7,850 net guillotine or pill crusher, for cutting the briquettes to length + €6,900 net Necessary for compressed air connection! Silo for MAP series + €19,940 net - Storage silo above the machine - Content approx. 6 sqm, stable steel construction with agitator discharge and level indicator. Nodpfxofmqq Ej Ac Tecu Transport line / cooling section (nominal value: 4x2m) each 2 meters 990 euros net Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site) according to expenditure on proof against separate calculation. The following sentences apply: Service technician/mechatronics technician per hour of assembly and travel: €129.00 Overtime: 25% surcharge 50% surcharge for each Saturday and night hour 100% surcharge for each Sunday and holiday hour Release per mechanic per day: depends on the country Per car and van and driven kilometer: 0.98 € / km Arrival and accommodation against receipt or flat rate billing at the expense of the client. . Test with the respective customer material: (by arrangement, up to a maximum of 750 kg) - 1,970 € net . Raw material requirements: - The moisture content (atro) must be between at least 6 and a maximum of 15% - Maximum chip length 18 mm - Installation temperature: room with a temperature of at least +5°C - The charge must be free of metals and mineral impurities. This can result in damage to the pressing tools and/or increased wear

Condition: good (used), Refurbished machine *Options at additional cost, see below with a full 1 year warranty Ready for delivery approx. 16 weeks after ordering Technical specifications: Throughput up to 1200 kg / h depending on the material (e.g. sawdust with a bulk weight of 150/180 kg / qbm) Briquette Ø 75 mm including 2 m press channel Main motor power 45 kW Feed screw gear motor 2 x 2.2 kw Compressor screw 2 x 5.5 kw Distribution auger 2.2 kw Hydraulic pump motor 0.37 kW Total connected load 65 KW Control panel with plain text display for operating states and utilization display for main drive and feed screws PLC control Siemens S7 / 300 with operating hours counter in the control cabinet Machine hat CE mark Automatic start / stop function of the machine Dimensions 3100x860x1800 mm lxwxh Weight 4500 kg Options: -Silo for MAP series Storage silo above the machine - Contents approx. 6 square meters, stable steel construction with agitator discharge and level indicator. 19,700 € net plus VAT. *only possible for one presse MAP 1200 below the silo if you need to place two machines MAP 1200 below one silo it needs to be build completely different. the price for this silo is 37.900 € net -Temperature control device for the pressing tools to maintain the temperature for optimal briquette size. Temperature controller for pump, cooling unit, fan, pressostat Wired ready for connection - must be left for operation including corresponding control € 7.850 net Ncedpfx Aco E Dqus Teu Oil heater 1.950 € net -Guillotine, to cut the briquettes to length Create a compressed air connection on site € 6,940 net plus VAT -Transport line / cooling section (nominal value: 4x2m) 990 euros net per 2 meters - Control System 4.995 € net Assembly / commissioning (nominal value approx. 2-3 days on site to install one press) based on effort and upon proof against separate invoice. The following sentences apply: Service technician/mechatronics technician per assembly and hour of travel: €129.00 Overtime: 25% surcharge 50% surcharge per Saturday and night hour 100% surcharge for every Sunday and public holiday hour Release per fitter per day: country dependent Per car, van and driving kilometer: €0.98 / km Arrival and overnight stay against receipt or flat rate bill at the client's expense. . Test with the respective customer material: (up to a maximum of 750 kg) - €1,970 net flat rate --- Recognition from the raw material: - The moisture content must be between a minimum of 6 and a maximum of 18% - Maximum span 20 mm - Excessive temperature: temperate room at at least + 5 ° C. - The loading must be free of metals and mineral impurities. This and the pressing tools and / or responsible wear can be the result

Year of construction: 2016, condition: ready for operation (used), This MAPLAN MFT 750/160 edition S was manufactured in 2016. It is a vertical injection moulding machine, ideal for precision plastic processing. Contact us for more information. Machine Benefits Technical Machine Benefits • Connected load: 84 kw • Nominal voltage: 3 x 400 v • Control voltage: 24 v • Safety distance: 310 mm • Overrun time: 128 ms • Overtravel: 62. 3 mm Nodpfx Acsx U Tihe Tjcu • Max platform height: 750 mm • Platform dimensions: 1850 x 1300 mm • The systems are fully functional and were used in 2/3-shift operation between 2017 and 2022. • The spray cylinders were resealed and the insulation panels replaced in 2023. Extra Information Machine still under power

Condition: as good as new (ex-display), Demonstration unit with 7 operating hours immediately available (ex works Neckartailfingen) Shredder MRZ 830 Commodity code: 84659600 Feed opening 800x1000 mm Motor: 18.5/22 kW; 400 V - 50 Hz - 3 phase Blades: multiple reversible Hydraulically operated slide Screen size optional (10 - 40 mm) Weight approx. 1,600 kg Dimensions (l x w x h) approx. 2290 x 1420 x 1750 mm Turbo coupling Standard equipment includes: - automatic star/delta start - fast hydraulics - auto. OFF when rotor is idle - speed 70-90 rpm for high throughput - cycle control to avoid idle times Ncsdpfev Sqrpex Ac Tsu - performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - vibration-damping machine feet - CE compliant The shredder is designed for shredding untreated wood, chipboard and MDF, and other materials after testing and approval by the manufacturer. Included: - Shredder raised by 30 cm (preparation for conveyor belt) Additional options for the shredder: - Articulated conveyor belt + €8,770 net Horizontal section: 1200 mm Inclined section: 2500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2000 mm + - 100 mm - Overband magnet + €6,780 net - Control for conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the shredder) Requirements for the raw material: - The moisture content (as received) must be below 30%, - Metals and mineral contaminants such as sand, stones, etc. will lead to increased wear.

Condition: new, Year of construction: 2026, production time appr. 4 months * for suction perception, see picture 4 and 5 Tariff number: 84659600 Main motor: 55 kW; 400 V - 50 Hz - 3 ph including turbo coupling, Hydraulic motor: 2.2 kW, 400 V - 50 Hz - 3ph Knife: 76 pieces, rotatable Knife size: 35 x 35 x 20 mm Rotor diameter: 360 mm Control: PLC Siemens S7-1200 Funnel opening approx. 1530 x 1235 mm Nodpfsd Hkqhex Ac Tocu Hopper volume approx. 2.5 square meters hydraulically operated slide Screen perforation: 10 - 30 mm Extraction nozzle Ø 200 mm Weight approx. 4,500 kg Dimensions (lxwxh) approx. 2765 x 2520 x 1730 mm Turbo coupling Included as standard: - V-rotor for other throughput - 2nd row of knives on the rotor - Control cabinet with Siemens PLC control - automatic star / delta start - fast hydraulics - Automobile. OFF when the rotor is idling - Speed ​​70-90 rpm for high throughput - Clock control to avoid idle times - Performance-increasing step control of the hydraulic slide - Pertinax guides for hydraulic slides - anti-vibration machine feet - CE conformity The shredder is for shredding natural wood, chipboard and MDF board other materials after testing and approval by the manufacturer Recognition from the raw material: - The moisture content (atro) must be below 30% - Metals and mineral impurities such as sand, stones, etc. Interests to interests wear

Condition: ready for operation (used), Year of construction: 2005, functionality: fully functional, travel distance X-axis: 700 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 500 mm, spindle speed (max.): 18,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range, X-axis: 700 mm Travel range, Y-axis: 1,000 mm Travel range, Z-axis: 500 mm Spindle speed: 1 - 18,000 rpm Ncjdpezd R R Ejfx Ac Tsu Tool holder: HSK-A63 Tool magazine capacity: 70 Tool-to-tool change time: 2.5 s Acceleration: 20 m/s² Travel speed: 120 m/min MACHINE DETAILS Number of pallets: 6 EQUIPMENT Integrated workpiece changer system High-dynamic 5-axis machining Weight-optimized kinematics Linear motor drives

Condition: as good as new (ex-display), We are offering you a second-quality post protector from the manufacturer SSI Schäfer for sale. The scope of delivery includes: 01x Post protector, second quality Material color: yellow Design: V Overall height: approx. 750 mm Overall width: approx. 124 mm Internal width: approx. 116 mm Overall depth: approx. 65 mm Nedpshr U Trefx Ac Tjcu Leg dimensions: approx. 65 x 65 mm Material thickness: approx. 4 mm Grid/hole spacing: approx. 300 mm Number of holes: 06 pcs. (03 pcs./side) Hole diameter: approx. 9 mm 06x Hex head screw: M8 x 35 mm 06x Lock nut: M8 06x Washers: M8 General information about the item: This item is offered for pick-up only. Any additional transport or shipping of this item will incur extra costs, which can be requested separately depending on the delivery location or scope of delivery.

Condition: excellent (used), Your contacts within our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch Mr. Simon Blank The scope of delivery includes: 1x post protector, used Material color: yellow Design: V Overall height: approx. 750 mm Overall width: approx. 100 mm Ncjdpfxeh Ei Uds Ac Tju Inner width: approx. 93 mm Overall depth: approx. 60 mm Material thickness: approx. 3.50 mm Grid/hole spacing: approx. 300 mm Number of holes: 06 pcs. (03 pcs./side) Hole diameter: approx. 11 mm 06x hexagonal screw: M8 x 35 mm 06x lock nut: M8 06x washers: M8 General information about the item: This item is offered for pick-up only. Any additional transport or shipping of this item will incur extra costs, which can be requested separately depending on the delivery location and scope of delivery. Our services at a glance: (Prices upon request) Assembly, installation Please note our general assembly conditions. Shelf inspection Shelf inspection according to DIN EN 15635, carried out according to the requirements of BGR 234, visual inspection for all shelving systems. Delivery with our own fleet of vehicles (without unloading)

Condition: excellent (used), Year of construction: 2017, Batch mixer, type WBX 1100 1 control unit for the mixer with frequency converter 1 cutter head, 5.5 kW 1 manual shut-off valve 1 separate control panel ("remote control")  maximum useful volume: 770 liters  mixing product: plastic granules  bulk density: ~0.7 - 0.8 kg/liter  product properties: free-flowing  mixing time: < 3 min. MACHINE DESCRIPTION Mixing drum  horizontal cylindrical mixing drum  end walls screwed to the drum Mixing system  mixing tools, such as ploughshares or inclined blades, screwed to blade arms in pockets Bearing  bearing of the shaft in flange bearing housings located outside the mixer, with roller bearings Sealing  shaft sealing by easily replaceable packing glands, packing glands cleaned by air Feeding  2 nozzles with flange, according to dimension sheet Ventilation  through 1 nozzle with flange, according to dimension sheet with filter bag incl. bracket and welded-in protective grid Discharge  via a dead-space-free closing flap, pneumatically operated  1 outlet nozzle with flange, according to dimension sheet Liquid feed option  none Inspection and cleaning  through 1 flap at the front of the drum, (1700 x 550) Nedpjza Ap Tofx Ac Tscu Flap closed by quick-release fastener  occupational safety and accident prevention by locking magnet and limit switch (not wired) Materials  mixing drum made of: stainless steel 1.4306  mixer shaft made of: stainless steel 1.4306  mixing tool made of: stainless steel 1.4306 Subject to prior sale Please send inquiries only by email Note: The machine is in storage and can be inspected on site. The buyer must arrange for shipping. This is not included in the quoted price.

Condition: new, Year of construction: 2026, Our best-selling briquetting press, the classic. + Tried and tested, simple technology for extremely low susceptibility to errors Ncsdpfxegl Nlmo Ac Tou + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Options for an extra charge: * Surcharge for the level indicator that enables automatic operation + € 995 net * Surcharge for large pre-compression chamber + 980 € (recommended for light material like straw) Briquette diameter: 50 mm Front bush: 50 mm Briquette stroke max .: 40 mm Briquette lift opt ​​.: 40 mm Throughput (depending on material): 30-60 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter . Motor power: 5.5 kW 400 volts / 50 Hz / 3 phases Length: 1680 mm Width: 1100 mm Height: 1500 mm Weight: 680 kg Oil volume: 110 liters Silo diameter: 1000 mm Silo content: approx. 0.7 square meters Pump: 27 liters Hydraulic pre-compressor Option cooling pressing tongs: no Hydraulic oil cooling option: yes Level monitoring option: yes CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Maximum chip length 15 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The customer must insure himself against loss of hydraulic oil - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: as good as new (ex-display), Year of construction: 2024, Special price: €29,970 net One machine is currently available for immediate delivery. This machine is ideal for shredding bulky, lightweight aluminum chips or turning chips. Not suitable for heavier aluminum parts. Included: + Optimized cutting geometry + Adapted slide control + Load-dependent controlled hydraulic slide (which presses the chips against the cutting mechanism) Motor: 18.5 kW; 400 V - 50 Hz - 3 phase Knives: 40x40mm, multi-rotatable Rotor diameter: 260 mm Control: Omron PLC Cutting mechanism opening: 600 x 800 mm Hopper volume: approx. 0.6 m³ Hydraulically actuated slide Screen size selectable (15 - 40mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (l x w x h) approx. 1737 x 1167 x 1650 mm The following options are available at an extra cost: - Raise the shredder by 30 cm (preparation for conveyor belt) + €2,990 net Njdpfjgmh H Tox Ac Tecu - Inclined conveyor belt (discharge height approx. 220 cm) + €9,770 net - Overband magnet + €6,980 net - Control for conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the shredder) We would be happy to provide a free test with your material. We invite you to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via a freight forwarder, and we will document the test with photos and videos.

Condition: new, Year of construction: 2026, Production time appr. 4 months Our best-selling briquetting press series + Tried and tested, simple technology for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several hundred machines in use with satisfied customers + Good price performance ratio Throughput approx. Up to 200 kg per hour * strongly dependent on the material. - in the last test with aluminum granules smaller than 5 mm - approx. 186 kg per hour + the pressed emulsion. - in the last test with aluminum chips smaller than 18 mm - approx. 120 kg per hour + the pressed emulsion. Technical specifications: Motor: 7.5 KW + 0,55 kW Cooler 400 volts / 50 Hz / 3-phase, Nedpfjchqxxjx Ac Tscu Front bush: 125 mm, Briquette stroke max .: 100 mm, Briquette stroke opt .: 80 mm, Pump: 80 liters, Storage container approx. 0.5 qbm content (expandable), Diameter: 1200 mm, with agitator discharge, Hydraulic unit complete with oil tank 220 liters Dimensions approx. 2095 x 1600 x 1310 mm lxwxh, Weight 1370 kg, Automatic on-off switching via level indicator CE compliant. . Requirements for the raw material: - Chip length maximum 20 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of magnetic metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: new, Year of construction: 2026, Diameter: 160mm Also available in the diameters: 180, 200, 250, 300 mm for an additional charge, other diameters on request. Very stable industrial design. Ideal for separating nails/metal parts from material flows. For example after a wood shredder. including 3 extremely powerful magnets Nsdochuvrepfx Ac Tscu * If desired, up to 6 magnets can be installed in the component - surcharge for each additional magnet + 49 € - Neodymium magnets are also available instead of ferrite for an additional charge Your advantages: + Extremely large inspection door with seal for easy stripping of the nails + Stable quick-release fastener +Made in Germany Inspection door / opening: 35x18 cm Installation length may vary

Condition: new, Year of construction: 2026, Availability upon request. Very robust machine with high pressing force. Njdped Nm Sisfx Ac Tocu - Also suitable for producing marketable briquette quality, depending on the material. The large-sized press cylinder and the 70 mm briquette size make this possible. Our best-selling briquetting press series: + Proven, simple technology for extremely low failure rates. + 25 years of experience, continuous development, and know-how. + Several thousand machines in operation with satisfied customers. + Excellent price-performance ratio. Additional cost for demonstration cooling unit: €4,980 net. (can also be retrofitted later) * cools the press tongs (important after 4 hours) and the hydraulic oil. * Cooling unit recommended for regular operation of more than 4 hours at a time. Commodity code: 84793010, Briquette diameter: 70 mm, Front bushing: 125 mm, Briquette stroke max.: 100 mm, Briquette stroke opt.: 80 mm, Capacity (material-dependent): up to 150 kg/h* * depending on the bulk density, * based on a bulk density of 200 kg per cubic meter. Motor power: 9.2 kW, 400 Volts / 50 Hz / 3-phase, Length: 2095 mm, Width: 1300 mm, * with large chamber 1600 mm Height: 1700 mm, Weight: 1250 kg, Oil volume: 220 liters, Silo diameter: 1200 mm Silo capacity: approx. 1 cubic meter Pump: 75 liters Hydraulic pre-compressor Optional cooling for press tongs: yes, with special accessory - coolable press tongs Optional cooling for hydraulic oil: yes Cooling of the press tongs and hydraulic oil with a cooling unit (special accessory) Optional level monitoring: yes Optional strand briquette: yes (material-dependent) Optional enlarged feed slide: yes, with special accessory - enlarged feed slide CE compliant Requirements for the raw material: - The moisture content (oven-dry basis) must be between a minimum of 6% and a maximum of 18%. - Chip length max. 20 mm - Installation temperature: temperature-controlled room with a minimum of +5°C - The feed material must be free of metals and mineral contaminants such as sand, stones, etc. Damage to the press tools and/or increased wear may result.

Condition: new, Year of construction: 2025, Another machine immediately available! Briquetting press with PLC control and automatic briquette length adjustment Throughput: up to max. 60 kg/h Briquette: 50 mm cylindrical Motor: 5.5 kW Dimensions: 1,900 x 1,350 x 1,410 mm Weight: approx. 860 kg Requirements: Nsdpfx Acev Rpxls Tscu Feed material should ideally be shorter than 25 mm chip length Moisture content 6–12% ATRO Machine suitable for intermittent operation. E.g. briquetting for up to 2.5 hours; 1 hour break, etc. If the machine needs to run longer than 2.5 hours continuously, optional cooling must be connected.

Condition: as good as new (ex-display), Year of construction: 2026, Machine for sale at a special price Machine available immediately (ex works Neckartailfingen) Demonstration machine Your advantages: + Very robust, simple technology + Excellent price-performance ratio + Suitable for continuous operation + Long-standing, well-functioning/established machine Includes control cabinet with timer operation The press is switched on manually and then runs until the set time on the timer has elapsed (e.g. 4 hours). Then the press switches off. Technical data: Briquet dimensions: 30/35 mm (square) Briquet length: 5-35 mm *depending on the material Throughput capacity up to a maximum of 25 kg/h *depending on the material Machine dimensions approx.: 137 x 75 x 148 cm (length x width x height) Machine weight: approx. 250 kg Capacity of the hopper: approx. 250 liters Motor: 2.2 kW, 400 V - 50 Hz Nodpfx Acsfci D Ao Tscu Noise emission: 62 dB Requirements for raw material: -Wood shavings and dust smaller than 15 mm in length -Moisture content less than 15% ATRO -Sand, stones, metals, and minerals increase wear --- Options available at an extra cost: -Timer function + €490 net Machine is started manually and switches off automatically after a set time X. -Level sensor for automatic operation + €1,450 net Press starts and stops automatically * NEW!!! Also available in 230 volts, Motor then 3 kW instead of 2.2 kW, Additional cost + €690 net (delivery time then approx. 8 weeks) ---

Condition: as good as new (ex-display), Year of construction: 2024, Special machine for shredding plastics Base machine from €24,990 net Well-suited for shredding: - Paper, cardboard, pipes, profiles, boxes, canisters, buckets, cans, sections of wooden pallets, etc. - Semi-rigid thermoplastics such as PVC, PP, PE, PS, PU, PET Includes: - Special rotor with embedded blades (reduced load absorption), - Small cutting gap between blade and counter-blade Motor: 18.5 kW; 400 V - 50 Hz - 3 phase Control: PLC Cutting unit opening (top) 600 x 800 mm The parts should be a maximum of approx. 500x500 mm *the height is less relevant Hydraulically operated slide Screen size as required (25 - 40mm) For plastics, coarser screens are recommended (30-40 mm) *If you want to shred finer, a two-stage shredding process with a downstream granulator type MVZ (screens 5-15 mm) is recommended. Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (l x w x h) approx. 1737 x 1167 x 1650 mm Further options available at an extra charge: - Raise shredder by approx. 25 cm (preparation for conveyor belt removal) + €1,980 net - Inclined conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overband magnet + €5,980 net - Control for conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the shredder) - Alternatively, manual start and stop on the conveyor belt + €595 net Requirements for the raw material: - The moisture content (as received) must be below 25% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear. We would be happy to offer a free test with your material. We invite you to visit us in Neckartailfingen for this purpose. It is also possible for you to send us your material by freight forwarder, and we will document the test with photos and videos. --- *only for brittle plastics with medium hardness, *not for elastic or extremely hard and heavy plastics - this would affect the durability of the system. --- Optionally, the next larger machines would be available: Base machine: Shredder MGZ 830 K-S - 18.5 kW Cutting unit opening (top) 800 x 1,000 mm The parts should be a maximum of approx. 720x700 mm *the height is less relevant from €39,995 net * Options depending on effort Base machine: Shredder MGZ 1030 K-S - 22 kW Cutting unit opening (top) 1,000 x 1,000 mm The parts should be a maximum of approx. 900x700 mm *the height is less relevant from €49,975 net * Options depending on effort Base machine: Shredder MGZ 1330 K-S - 37 kW Cutting unit opening (top) 1,300 x 1,200 mm The parts should be a maximum of approx. 1,200x700 mm *the height is less relevant Njdpfx Aed H R Sxjc Tocu from €79,975 net * Options depending on effort

Condition: new, Year of construction: 2026, Your advantages: + extremely large cutting unit opening with 1300x1200mm + special rotor suitable for hardwood and softwood + Energy-efficient and powerful with 37 kW at start-up Technical specifications: Colour: grey / blue Feed opening (mm): 1,300 x 1,200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Power requirement (kW): 37 Screen perforation (mm): 30 - 50 mm - selectable Tools: 37/70 knives Extraction nozzle Ø (mm): 200 mm Dimensions: 2430x2410x1735 mm (lxwxh) Weight (approx. Kg): 3,920 Optional for a surcharge: * to shred veneer or paper (anything thinner than 3 mm) - we recommend a segment floor. The machine in preproduction has not yet installed this. Special option at an additional cost. - 2nd row of knives, for up to 30% more throughput - Fast hydraulics, for increased throughput Ncsdpfx Acjgbkkrj Tou - Preparation for conveyor belt removal - conveyor belt - HAWK-EYE overbelt magnet --- Optimal pallet size with the option slide extension = 1200x1400 (option slide extension, the cutting unit opening 1300x1700 surcharge + 12,975.00) * is associated with significantly longer production time. * larger machines on request --- Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear

Condition: new, Year of construction: 2026, Briquetting press NEM 900: production time appr. 5 months for briquetting aluminum chips Throughput: up to maximum 320 kg / h * more details after a free test with heard material . Briquette diameter: Ø 70 mm Optimal briquette length: 70 mm . Technical specifications: Total connection: approx. 31 kW In continuous operation approx. 22 kW 400 volts / 50 Hz / 3 phases Pump: 120 + 60 liters per minute Silo: 1 m³ Silo rollers: 1200 mm Including agitator Oil tank: 600 liters Dimensions: 2500 x 1700 x 1730 mm lxwxh Weight: 2250 kg. Hydraulic pre-compression via slide Ncsdpfxogfm Ryj Ac Teu Main press cylinder Vertical cylinder Above for connecting a cooling unit . One and the source material - max.span: 18 mm - Excessive temperature: temperate room at at least + 5 ° C. - max.weight on agitator: 200kg. - The loading must be free of metals and mineral impurities such as sand, stones, etc. This on the pressing tools and / or responsible wear can result

Year of construction: 2026, condition: new, *Only the neodymium overbelt magnet is offered, not the conveyor belt underneath. Nodpsdubpuefx Ac Tscu *Neodymium magnets are among the strongest magnets in the world. They have an extreme pulling power and cannot be compared to ferrite magnets. Extremely high degree of separation, depending on the bulk height and the starting material. Probably the most compact overband magnet on the market. The competition often uses the less powerful ferrite magnets to save costs. dimensions approx. Length: 104cm Width: 22cm Height: 28 cm (at the motor) *Without controller Surcharge for simple manual start/stop control + 495 € A high-performance industrial neodymium magnet is installed. High-performance neodymium magnet approx. 600x68x36.5 mm * So nails are attracted to a length of 600 mm and thrown off to the side, in the area that is no longer magnetic. This overbelt magnet should be mounted approx. 5 - 9 cm above the material flow. *Assembly/suspension on site Ideal for separating nails from wood chips. Optionally also in a single-shaft shredder that is sucked off Requirements: *Your belt width or useful width inside (of the existing conveyor belt) should ideally be narrower than 55 cm *Suitable for separating nails from material flows that are less than 12 mm high and with a chip length of less than 25 mm. ----- Optional at extra charge: Cross and ascending belt demonstrators from € 7,995 net

Condition: new, Year of construction: 2026, operating hours: 8 h, Very robust machine with high pressing force - is also suitable for producing a salable briquette quality * depending on the material. The large press cylinder and the 80 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Surcharge for cooling unit + € 4.995 net, (can also be retrofitted later) * cools the pressing tongs (important from 3.5 hours) and the hydraulic oil * Cooling device recommended for regular use of more than 3.5 hours at a time. Briquette diameter: 80 mm Front bush: 125 mm Briquette stroke max .: 100 mm Briquette lift opt ​​.: 80 mm Output (depending on material): up to 200 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter Motor power: 9.2 kW 400 volts / 50 Hz / 3 phases Length: 2095 mm Width: 1300 mm Height: 1700 mm Weight: 1250 kg Oil volume: 220 liters Silo diameter: 1200 mm Silo content: approx. 1 qbm Pump: 75 liters Hydraulic pre-compressor Cooling pressing tongs option: yes, with special accessory coolable pressing tongs Hydraulic oil cooling option: yes Cooling of the pressing tongs and the hydraulic oil with cooling device (special accessory) Level monitoring option: yes Strand briquette option; yes (depending on material) Option of enlarged filling slide: yes, with special accessory enlarged filling slide CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Chip length maximum 20 mm Nsdpfx Aoxfwdjc Tjcu - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: new, Year of construction: 2025, Ideal for shredding straw, polystyrene, leaves, hay, and bread. Throughput is highly dependent on the screen and the input material: - up to a maximum of 350 kg/h for straw with a 15 mm screen - up to 60 kg/h for EPS with a 15 mm screen Motor: 11 kW - 400 volts, (9.2 kW or 15 kW also possible upon request) Optional: *Additional cost for the next larger machine with 18.5 kW and a larger silo diameter: + €2,750 net Robust steel construction, hardened cutting blades, Nsdpfx Acezbizs Tocu screen with interchangeable inserts, optionally with (10), 15, 22, 26, 30, 40, or 60 mm perforations For electric drive with star-delta starter, overload protection, and 8 m power cable, ready for connection, discharge spout 150 mm, optionally for plastic or grain pipes, blowing distance approx. 12 m, chassis with 2 running wheels, Ø 380 mm, and one pivoting support wheel, Ø 125 mm, all wheels with solid rubber tires, dimensions approx. 1200 x 900 x 1270/1400 mm (l x w x h) Weight approx. 240 kg, Spare part prices and options: 24 blades, hardened, €9.90 net each 6 bolts, €14.90 net each 1 screen, €475 net Cover, €290 net each Polystyrene disc: €600 net each

Condition: as good as new (ex-display), Year of construction: 2025, Demonstration machine with approximately 9 operating hours Another machine, available immediately (ex works Neckartailfingen) *Options available at an extra charge - see below Included: + Profile rotor for higher throughput We would be happy to provide a free test with your material. We invite you to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via a freight forwarder, and we will document the test with photos and videos. Motor: 18.5 kW; 400 V - 50 Hz - 3-phase Knives: 15 pieces, reversible Option: double knife row + €995 net Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Cutting chamber opening: 630 x 820 mm Hopper volume: approx. 0.6 m³ Hydraulically actuated slide Screen mesh size as desired (10 - 40 mm) Suction nozzle Ø 160 mm Weight: approx. 1,300 kg Dimensions (L x W x H): approx. 1737 x 1167 x 1650 mm Moisture content: < 30% (dry basis) . Standard included: - V-rotor for maximum throughput - Control cabinet with Siemens PLC control - Automatic star/delta start - Fast hydraulics - Auto. OFF when the rotor is idle - Speed 70-90 RPM for high throughput - Cycle control to avoid idle times - Performance-enhancing stepped control of the hydraulic slide - Pertinax guides for hydraulic slide - Vibration-damping machine feet Nodpfx Acjb Ny Eye Tecu - CE compliant . Optional shredder features at an extra charge: - Raise the shredder by 30 cm (preparation for a conveyor belt) + €2,080 net - Eco-rings: + €1,980 net (recommended for more than 20% hardwood) - Double knife row + €995 net - Special scraper + €990 net (recommended when shredding veneer or paper, or items with a material thickness of less than 3 mm) - Articulating conveyor belt + €8,770 net Angle: adjustable from 0-60 degrees Discharge height: approx. 2000 mm - Automatic overband magnet + €5,980 net Alternatively, a fixed magnet block above the conveyor belt for regular manual removal + €990 net (in case of low metal content) - Control for conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the shredder) alternatively, manual start and stop of the belts + €595 net . Requirements for the raw material: - The moisture content (dry basis) must be below 30% - Installation temperature: temperature-controlled room at a minimum of +5°C - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear

Condition: new, Year of construction: 2026, Consisting of a bale shredder for large round bales, type MHB, and a straw shredder, type MHZ. 1) Bale Shredder MHB: Special price from €22,975 net (manufacturing time approx. 15 weeks) Suitable for round or rectangular bales. Includes frequency inverter (FU) – this controls the speed of the scraper bed. The bales are placed on the scraper bed, and the feed of the shredder is activated. The tines of the shredder tear the straw from the bale and fling it into the hopper. The combination of a bale shredder and a straw shredder is ideal in this case. Technical data of the bale shredder: Capacity: 1-2 bales per hour up to a maximum of 600 kg per hour (depending on the screen size used in the straw shredder, kW, number of straw shredder). Without a straw shredder, the bale shredder can even process up to a maximum of 900 kg/h of straw. Maximum size of rectangular bales: 2400x1200x800 mm (l x w x h) Shredder motor: 5.5 kW, 380 Volt Scraper bed feed: 0.75 kW, 380 Volt Dimensions: 3750x1730x2460 mm (l x w x h) Weight: 400 kg 2) Straw Shredder MHZ 600 - 11/15 kW; immediately available Special price from €6,995 net Additional cost for the even larger straw shredder (18.5 kW): + €2,750 net Technical data, MHZ with special hopper: Motor: 15 kW, 380 Volt electric motor Diameter: 600 mm Hardened cutting blades Screen with interchangeable inserts Optional (10, 12, 15) 22, 30, 45 mm hole size With star-delta starter, overload protection and 8 m supply cable, ready for connection Discharge nozzle: 160 mm Throwing distance: approx. 12 m Dimensions: approx. 1600 x 1020 x 1360 mm (l x w x h) Weight: approx. 240 kg --- Options at an extra cost: Infeed auger: + €970 net Cyclone (mounting to be carried out by the customer): *should be located a maximum of 10 m away. + €2,970 net Simple filter: €1,750 net --- Other options: Industrial extraction system (demonstration model): + from €9,950 net Optionally with rotary valve *makes the material pressure-free: + €5,750 net Control system: from €1,620 net Special shredder extension, 3 m *other sizes would need to be calculated: + €9,750 net Briquetting press MPP 180 S; slightly used demonstration model 70 mm briquettes - up to a maximum of 100 kg/h From €39,700 net *larger machines on request --- Description: The muetek bale shredder was developed for shredding round and rectangular bales of hay and straw. The shredder, which is flange-mounted to the bale shredder, shreds straw from all types of grain, hay, corn, and miscanthus. The muetek machines in the MHZ/MHB series are characterized by a robust design and solid construction. The muetek bale shredders in the MHB series are equipped with a chain conveyor onto which the straw bale is placed using a front loader. The support is adjustable depending on the type of bale. The chain conveyor pushes the bale against the shredder rotor, and the feed speed is adjustable. The shredder rotor is equipped with several tines that tear the straw bale apart. The straw detached from the bale is ejected. --- In principle, the machines are designed for dry materials: - Straw - Hay Nodpfx Acsb Nulho Tscu --- Shredding hemp only works with a special shredder. Additional cost: approx. €9,720 net *depending on the design. Shredding hemp does not work with the straw shredder. Requirements for the raw material: Moisture content: maximum 12%

Condition: like new (used), functionality: fully functional, Year of construction: 2025, operating hours: 55 h, Machine with special rotor available immediately Advantages: + special rotor with reduced blade overhang, suitable for hard and soft materials + 22 kW motor Ncedpfxjx Af Rde Ac Tju + effective square blades *for pallets: up to a maximum of 10 pallets per hour *dependent on screen size and material. With smaller wood residues, significantly more. Motor: 22 kW; 400 V - 50 Hz - 3 phase, Screen: 15/20 mm or as agreed (10 to 40 mm possible) hydraulically operated slide Screen opening currently (15/20 mm) *can be exchanged Extraction nozzle Ø 200 mm. Feed opening 1000x1000 mm Dimensions: 2000x1800x1645mm Example image above: color of the system may vary Weight: 1920 kg. Included as standard: - Control cabinet with PLC control - automatic star/delta start - fast hydraulics - auto. OFF when the rotor is idle - speed 70-90 rpm for high throughput - cycle control to avoid idle times - performance-enhancing step control of the hydraulic slide - Pertinax guides for hydraulic slide - vibration-damping machine feet - CE compliant The following options are available at an extra cost: - Raise shredder by 30 cm (preparation for conveyor belt) + €2,480 net - Inclined conveyor belt (discharge height approx. 220 cm) + €12,980 net - Overband magnet + €6,980 net - Control for conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the shredder) - extended feed hopper 1500x1500 mm + €3,480 net Requirements for the raw material: - The moisture content (as received) must be below 25% - The feed must be free of metals and mineral contaminants. Damage to the tools and/or increased wear may result.