Used Powder Painting Equipment for sale (43,378)

Condition: used, Year of construction: 2010, functionality: fully functional, Wagner Powder painting equipment for sale! Powder coating device, year 2010 consisting of: Booth: Prima Cube 16000 Powder supply: Powder Center Powder recovery: Cyclon Filter 16000 Movement generator: KHG 350 Production process configurations INCLUDING: I. Presumes Maximum size of parts: LxWxH=2600x400x1850 mm II. Equipment Technological Conveyor automatic speed V=1.2 mtrs/min. Speed regulation between 0.5-2.5 mtrs/min 1. Pretreatment Stand MNA-3-LPG, total size 16,7 mtrs Enter size L=2,5 mtrs a. Washing, degreasing and phosphating; L=3,6 mtrs -number of spray frames – 10 -number of nozzles in frame – 18 -number of nozzles in total – 180 -delivery of the pump – 162 m3/h Iijdpfx Aoww Adtjnwoc -power of the pump – 15 kW -vessel 4 m3 for active liquid -inner heat exchanger with LPG burner – 160 kW -temperature 500C -mechanical oil separator - solution filter -the dosing system, membrane pump with regulator -washing time – 3 min b. Dripping zone L= 3,1 mtrs -time of dripping – 2 min 30 sec c. First rinsing; L= 1,2 mtrs -number of spray frames – 4 -number of nozzles in frame – 18 -number of nozzles in total – 64 -delivery of pump – 38 m3/h -power of the pump – 3 kW -vessel 1,5 m3 for water -first rinsing time – 1 min c. Dripping zone L= 3,1 mtrs -time of dripping – 2 min 30 sec d. Fine rinsing; L= 1,28 mtrs -number of spray frames – 3 -number of nozzles in frame – 18 -number of nozzles in total – 54 -delivery of pump – 33 m3/h -vessel 1,5 m3 for water -power of the pump – 3 kW -one extra spray frame -number of nozzles in frame – 18 -fine rinsing time – 1 min e. Dripping zone L= 2 mtrs -time of dripping – 1 min 40 sec Three openings to connect to exhaust system with three ventilators Operating space made of stainless steel. Pipes made of PVC or S/S. 1 unit 2. Automatic Dryer after water AST-1-KLPG: - operating space dimensions LxWxH=7000x3000x2800 - air curtains each side to avoid heat losses - one indirect heat exchanger heated with liquid petrol gas to produce 200 kW of rated power - three blowers 6000 m3/h of air delivery - two openings to connect to exhaust system - temperature sensor and temperature regulator - overheating sensor - circulation sensor - operating space made of zinc plated steel - thermal insulation 200 mm thick - drying time 10 min 1 unit 3. Automatic Curing Oven APT-2-KLPG for curing powder paints - operating space dimensions LxWxH=10200x3600x2800 - air curtains on one side to avoid heat losses - two indirect heat exchangers heated with liquid petrol gas to produce 300 kW of rated power, of each - eight circulation blowers, capacity of each 6 000 m3/h - two openings to connect to exhaust system - temperature sensor and temperature regulator - overheating sensor - circulation sensor - operating space made of zinc plated steel - thermal insulation 200 mm thick - curing time 25 min 1 unit 4. An overhead rail conveying system ATR-ADAX, for the paint shop including the following: • straight track with hangers L=400 mm 146 mtrs • drive station 2 pc • tension station 1 pc • chain lubrication station 1 pc • drawing of the track supporting structure 1 set

Condition: new, Year of construction: 2026, functionality: fully functional, Ball Mill with Air Classifier: The Ultimate Powder Processing Equipment In the world of industrial powder production, precision, efficiency, and flexibility are paramount. Whether producing ultra-fine powders for high-tech applications or coarser materials for everyday products, the combination of a Ball Mill with Air Classifier offers unparalleled performance. This dynamic duo provides a comprehensive solution for industries ranging from chemicals and ceramics to paints, plastics, and pharmaceuticals. This article introduces the ball mill with an air classifier, explores its applications, and highlights the key advantages of this essential powder equipment. General Introduction to Ball Mill with Air Classifier ball mill with air classifier is an advanced grinding and classification system designed for efficient, high-quality powder production. The system consists of two main components: 1. Ball Mill: A cylindrical grinding device filled with grinding media (such as steel balls) that operates by rotating around its axis. The raw material is reduced to smaller particle sizes through impact and friction within the mill. 2. Air Classifier: A sophisticated device that separates particles based on size using airflow. Fine particles are carried away, while coarser particles are returned to the ball mill for further grinding. The combination of these two components creates a closed-loop system that ensures consistent particle size distribution, high efficiency, and minimal waste. Applications of Ball Mill with Air Classifier The ball mill with air classifier is a versatile solution used in a wide range of industries to process various materials. Key applications include: 1. Mineral Processing The system is widely used in the production of minerals such as calcium carbonate, quartz, feldspar, and talc. These finely ground minerals are essential for industries like ceramics, paints, plastics, and rubber. 2. Cement and Construction Materials Cement and other construction materials require precise particle size control for optimal performance. The ball mill with air classifier ensures uniformity and enhances the quality of construction materials. 3. Chemicals and Pharmaceuticals Fine powders play a critical role in the chemical and pharmaceutical industries. From active pharmaceutical ingredients (APIs) to industrial chemicals, this system delivers the consistent quality required for these applications. 4. Paints, Coatings, and Pigments The production of paints and coatings demands ultra-fine powders to achieve smooth finishes and vibrant colors. The ball mill with air classifier produces high-quality powders for superior results. Iisdpfx Ansvlwkxewec #### 5. Food and Agriculture Food-grade powders such as additives, preservatives, and agricultural products like fertilizers can be efficiently processed using this system, meeting stringent regulatory requirements. Industries That Benefit from Ball Mill with Air Classifier Several industries rely on the capabilities of this system to produce fine powders with specific characteristics: - Ceramics: Produces high-purity powders for tiles, insulators, and advanced ceramics. - Rubber and Plastics: Creates fillers and additives for improved durability and performance. - Pharmaceuticals: Ensures consistent particle size for APIs and excipients. -Construction: Delivers materials for concrete, plaster, and other applications.

Condition: good (used), Year of construction: 2016, functionality: fully functional, machine/vehicle number: K974.016, Plasma spraying system - Comfort control panel - Gas regulation cabinet for plasma - Power source PPC 2002 NG - JamBox - Powder feeder PF 2/2 Isdpfx Aeym Ay Eenwoic - Plasma torch - Plasma hose and cable set for 9MB - Sigma 67-2K water recooler with 2 cooling circuits for separate use of a 9MB and TopGun torch - Control cabinet - TS modem adapter

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, total length: 24,000 mm, total height: 4,200 mm, type of input current: AC, warranty duration: 12 months, workpiece weight (max.): 9,500 kg, power: 48 kW (65.26 HP), input voltage: 380 V, temperature: 20 °C, input frequency: 50 Hz, heating capacity: 6 kW (8.16 HP), inner dimension length: 24,000 mm, inner dimension width: 4,200 mm, workpiece height (max.): 1,500 mm, workpiece length (max.): 3,000 mm, waste water connection: 100 mm, feed length Y-axis: 16,000 mm, energy consumption: 42 kWh, insulation material: Steinwolle, insulation thickness: 50 mm, nominal power: 48 kW (65.26 HP), output voltage: 380 V, sheet thickness steel (max.): 3 mm, type of output current: AC, tank capacity: 4,000 l, number of previous owners: 1, number of chambers: 4, Equipment: lighting, This is a pre-treatment system in which metal parts are automatically cleaned using a spray process. Iiedpezd Sm Ijfx Anwec

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 Isdjzduplspfx Anwjic ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: used, Year of construction: 2011, AABO Powder coating line Iiedeyrnh Eepfx Anwjc

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, total height: 2,700 mm, total width: 2,490 mm, Hercules is a revolutionary, portable system for flame spraying coatings onto metal substrates, drip trays, containers, steel structures, concrete floors, and other surfaces. It represents the most efficient technology for corrosion protection through the application of a thermoplastic, environmentally friendly coating directly on site. Iedpozarzlofx Anwoic

Year of construction: 2018, condition: used, The year of manufacture refers to the final acceptance of the system; individual components may differ in age. Workpiece dimensions up to a maximum of L x W x H: 8,000 x 2,000 x 2,000 mm, maximum crossbeam load: 2,000 kg/carriage, material: steel. Pos. 1: Washing booth, Jumbo-Clean with stainless steel interior for degreasing/phosphatizing of steel, either automated or with manual spray lance. Pos. 2: 1 set of belt filters. Pos. 3: 1 automatic spray ring for the Jumbo-Clean washing booth, including a central lance. Pos. 4: 1 fresh water treatment system. Pos. 5: 1 manual conveyor with 1 electric cross-travel carriage. Pos. 6: 1 lifting/lowering station, Jumbo-Lift 2000, integrated into the cross-travel carriage. Pos. 7: 1 indirect gas-heated flash-off oven/powder drying oven/wet coating drying oven, door opening W x H: 2,800 x 3,100 mm, clear length: 9,500 mm, overall W/H/L approx.: 4,000/5,000/10,000 mm. Pos. 8: 1 end-face powder coating extraction system for an on-site painting booth for spraying and drying operations. Pos. 9: 1 manual coating unit, OptiFlex(R)2. Pos. 10: 1 structure for on-site steel construction. Pos. 11: Control cabinet. Iisdey T Nzdjpfx Anwec

Condition: used, Year of construction: 2000, functionality: fully functional, input voltage: 380 V, temperature: 250 °C, inner dimension length: 1,000 mm, inner dimension width: 1,000 mm, inner dimension height: 1,500 mm, For sale: Eliogtherm Kelvin curing oven / industrial dryer. Comparable to TRO ovens, Reinhardt ovens, or those from Nabertherm. This high-quality dryer is suitable for drying and curing paints, coatings, powder coatings, and screen prints at temperatures up to 250°C. The oven is also ideal for preheating materials. It is approved for drying solvent-based materials. The exhaust air is monitored by a pressure sensor. The oven is very well insulated, not only on the walls but also on the base. Intake air is filtered through a large filter to prevent dust particles from entering the chamber. Internal dimensions: 1000 mm x 1000 mm, height 1500 mm. Comprehensive documentation is included (manuals, wiring diagrams, etc.). The oven is currently stored at our warehouse near Cham in the picturesque Bavarian Forest—a visit is definitely worthwhile! Iiodpfxoy Svqie Anwoc We can arrange shipping by freight forwarder upon request. Loading with a forklift onsite is not a problem. If you have any questions, please feel free to contact us.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, The company sells Ransburg NO-2-701A. The machine is brand new. Ransburg No.2 Electrostatic Spray Gun The Ransburg No.2® electrostatic spray gun provides ultra-fine atomization and nearly 100% paint transfer efficiency. The system uses an air-driven rotating spray bell to create a high-quality electrostatic finish with minimal overspray. It is designed for professional coating applications and is especially suitable for intricate metal parts, fences, gates, railings, wire products, office furniture refurbishment, and other industrial painting tasks. Iiodey Tbtfspfx Anwjc Technical Specifications Maximum output voltage: 90 kV Air consumption: max. 150 l/min Weight: 1.25 kg Length: 500 mm Power supply: 230 V / 50 Hz Protection class: IP54 Included in the complete system: Electrostatic hand spray gun with 4” bell 7.5 m high voltage cable 7.5 m fluid hose 7.5 m air hose High voltage control unit Air filter/regulator 10 L pressure tank Cart frame system

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. Ijdpfxjfz Dubj Anwjic The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ Iijdpfsyg H Erjx Anwsc 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2026, 🏭 POWDER COATING BOOTH KPP Iiodpfsfy T Tbox Anwec Automatic filter cleaning with adjustable pulse timing, plus manual mode. 🧼⏱️🖲️ 100% polyester filters - washable, water-resistant, long-lasting. 🧵💧♻️ ROMER JET™ filter cleaning - patented high-speed air pulse for powerful cleaning. 💥💨🏅 Low-noise aluminium fans (74-79 dB) - safer, spark-minimized operation with low power use. 🔇⚡🛡️ Adjustable airflow baffle - antistatic plate protects filters and improves extraction. 🌬️🛡️📈 Leak-tight filter mounting - gasket + clamp for strong sealing and easy service. 🔩🧷✅ Touchscreen control - auto (time), auto (clogging sensor), manual + filter change alerts. 📲🔁⚠️ Optional powder container - waste collection or fluidized tank with direct applicator feed. 🧺💨🎯 Overhead puller - moves beams through the booth, reducing manual effort. 🏗️➡️💪 Integrated sieving unit (with container) - clean recovered powder for reuse, EX-zone vibrator. 🧪♻️⚙️ Explosion-proof design - components selected to prevent explosive mixtures. 🛡️💥✅

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Ijdpfx Anefz Apqewjic Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Iisdpfx Aefz U Nbsnwec Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Ijdpfofz I Rxex Anwoic Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). Iodpfx Aefz Dt Nonwjic - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Iiodpfx Anofz I D Djwoc Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. Iiodpjfz I Edsfx Anwsc - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators. Iisdpfxjflmdwo Anwoc

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Iiedpfjfzkrnjx Anwoc Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 Iiedpfeflk Awjx Anwoc ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Iijdpfxofz Nb To Anwec Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. Iiodjfz U S Espfx Anwjc This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Iisdpfxefz U Tij Anwjc Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.