Used Sidel Sidel Sbo Blow Moulding Machine for sale (67,329)

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Maximum preform length 210 mm Gkedpfx Asg Ailcefujc MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: used, Year of construction: 2000, Overview  This PET blow-moulding machine was manufactured in 2000 by French company SIDEL. The machine is currently in good working condition, running in production until the end of November 2025. It will be dismantled and craned out through the roof, with craning scheduled for December 2025. It becomes available after dismantling. Technical data - Capacity: - 7,600 bph on 1.0 L - Formats: - Neck finish 29/21 - Preforms processed: RPET Plastipak & Resilux - Number of moulds: - 6 (moulds not included) - Equipment & Features: - Quick change for shell molds - Sidel caterpillar oven - 6 heating modules Gkjdpfxeyb Tbpj Afusc - Sidel preforms tipper - Sidel preforms hopper & feeder - Sidel preforms infeed rail - Sidel caterpillar oven & blowing wheel - Solenoid valves Sidel Universal type - Sidel PCC version V2.02 - Sidel CE electrical cabinet (Siemens) - Service history: - Sidel maintenance completed September 2024 - Elongation sensor retrofitted - Additional service by client’s technicians Scope of Delivery  - Stretch blow-moulder SIDEL SBO 6 Series 2 - Preforms tipper - Preforms hopper & feeder - Preforms infeed rail - Caterpillar oven & blowing wheel

Condition: used, Year of construction: 2006, Overview This SIDEL SBO 2 XL Compact is a two-cavity PET stretch blow moulding machine built in 2006 for large-format containers of up to 10 litres. It pairs a Sidel preform tipper, hopper and feeder with a Sidel Compact linear oven with 5 heating modules and a blowing station for two moulds. Output depends on bottle size: approx. 2,400 bottles/hour at 500 ml, approx. 2,000 bottles/hour at 5 litres and approx. 1,000 bottles/hour at 10 litres. The machine is currently set up for preforms with a 48/41 neck finish and last produced 8-litre PET bottles. Its hour counter reads approx. 12,500 hours. It ran in a plastics converting plant until March 2026 and was then dismantled by skilled technicians and stored dry. Large-format blow moulders of this size are rarely offered on the second-hand market. Moulds are not included. Technical data - Manufacturer: SIDEL - Model: SBO 2 XL Compact - Year of manufacture: 2006 - Machine type: PET stretch blow moulding machine - Bottle size range: approx. 2.0 to 10.0 litres - Current bottle format: 8 litre PET - Current neck finish: 48/41 - Mould stations: 2, block moulds - Moulds: not included - Oven: Sidel Compact linear oven - Heating modules: 5 - Output at 500 ml: approx. 2,400 bottles/hour - Output at 5 litres: approx. 2,000 bottles/hour - Output at 10 litres: approx. 1,000 bottles/hour - Operating hours: approx. 12,500 h - Control: Siemens SIMATIC touchscreen HMI Equipment - Sidel preform tipper - Sidel preform hopper and feeder - Sidel Compact linear oven with 5 heating modules - Sidel blowing station for 2 moulds - Sidel electrical cabinet - Sidel drive panels with Siemens touchscreen control - Safety enclosure with transparent guard panels - Electrical and mechanical drawings, service and maintenance manuals, spare parts books Condition Used - good working condition. The machine was serviced by Sidel and by in-house technicians under a regular preventive maintenance schedule, and ran in production until March 2026. It is now dismantled and stored dry and can be inspected in stored condition. Gsdpezxtzijfx Afujkc Availability Immediately. Location: France. Ready for loading and shipment.

Condition: used, Speed: 8.000 bph with 0,5 liter bottle. Different formats are possible optionaly. Godpfx Aoz Icmwjfujkc Dismanteling is made by Seegräber GmbH on begining februar 2018. List of machines included: -SIDEL SBO 6 Blowing machine. Completly overhault by SIDEL in 2006. -Preform magazin and preform elevator Compressor, cooling, moulds not included

Condition: used, Year of construction: 1998, Overview This SIDEL SBO 10/14 Series 1 is a rotary PET stretch blow moulding machine with 10 blowing stations, producing up to 12,000 bottles per hour. It has been used for the production of 1.5 L and 2.0 L PET water bottles with PCO 1810 neck finish. The machine is still installed and in production, can be visited in operation, and is available for immediate sale. Technical data - Manufacturer: SIDEL - Model: SBO 10/14 Series 1 - Year of manufacture: 1998 - Machine type: rotary stretch blow moulding machine for PET bottles - Blowing stations: 10 - Capacity: up to 12,000 bph - Formats: 1.5 L and 2.0 L PET bottles - Neck finish: PCO 1810 - Installed power: 310 kW Godpfezrhr Asx Afuskc - Electrical supply: 400 V / 470 A Condition Used - in production, still installed and under power. The machine remains a reliable solution for water, beverage and other PET packaging applications. Availability Immediately available. Location: Slovenia. Dismantling, handling, packing and truck loading can be quoted on request (EXW).

Condition: used, Year of construction: 1998, Overview This machine was built in 1998 by French manufacturer Sidel. The machine is in very good working condition, is already professionally dismantled and stored in a warehouse. It is already packed in seaworthy export crates. Techn. Details - Capacity: 7.200 bph in 1,5L - Number of moulds:  6 (molds not included) - Equipped with quick change for shell molds Gkedpfjrkgy Uex Afuec - Number of heating modules: 10 modules - Neck personalization: 29/25      - Working hours: 47.000 only         - Machine was regularily maintained       - Retrofitted by the previous owner in 2020 - Machine equipped with:            - Sidel preforms elevator to unscrambler - Sidel preforms unscrambler & feeder - Sidel oven & blowing wheel for 6 molds - Sidel electrical cabinet - Sidel PCC drive & control panel - Big set of spare parts list upon request

Condition: used, Year of construction: 1992, Overview This blowmoulder was built in 1992 from French manufacturer Sidel. It can produce up to 4.000 bottles per hour. Techn. Details Capacity: 4.000 bph 4 cavities Scope of delivery Blowmoulding machine | SIDEL | SBO 4/6 | 1992 Preform feeder Two types of molds for 1.5 L and 2.0 L bottles Cooling unit: RIEDEL Gjdpenpbhvjfx Afuokc

Condition: used, Year of construction: 1998, Automatic PET bottle blowing machine Manufacturer: SIDEL Type: SBO 16/16 S1 Gkedpfeutni Rjx Afujc Year of manufacture 1998 Capacity: 16,000 for 1.5 L bottles and up to 19,000 bph for 0.5 L bottles Installed power: 347 kW Includes 1.5 L moulds Preform feeder Chiller cooling unit Technical condition: used machine, functional until dismantled. The machine is currently dismantled, assembled in elements and prepared for transport. Full and original technical documentation.

Condition: new, Parts for the SIDEL blow molding machine bearings O ring nozzle Godpsiqum Iefx Afuekc strap sealing axis

Condition: used, Year of construction: 1999, - PET-Blow moulding machine, make Sidel, type: SBO 16 with preform tipper, preform feed, unscrambler, preform transport, built 1999, already dismantled, ex location for sale. Gkodpfx Aforazwrjujc - PET-Blow moulding machine, make Sidel, type: SBO 20, with preform tipper, preform feed, unscrambler, preform transport, built 1999, already dismantled, ex location for sale.

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, ID BYP01 We sell a used Chinese - PP melt-blown fabric extrusion line for melt blown, make: Zhangjiagang Sevenstars Machinery Co., Ltd., MFG 2020. It was used for a short time. excellent condition. All EU import duties have been paid. Output max 400 kg per 24 hours. General description: 1. Product size: PP melt blown fabric with width at 600mm (after trimming 17m*3) 2. Main Material: PP compounding material 3. Extruder type: SJ65/33 single screw extruder 4. Output capacity: 350-400kg/24hour 5. Electric power supply: 3phase, 380V; 50Hz 6. Additional equipment: • Vacuum feeder • Raw material dryer • Mesh manual filter • T-mould for melt blown fabric • Static electrical discharge equipment Gsdpfx Afjuiq Dheuekc • Belt type forming 850mm • Collecting device • Winder and slitting Model L/D Output Speed of Screw Rotationl Power Center Height SJ-65 10-33 80-150kg/h 20-120r/min 18.5kw 1000mm This line contains the following machines: Automacic vacuum loader ZJ-400 and hopper dryer make RHONG model RDM-25, MFG 2020; Single screw extruder, model SJ65/33, MFG 2020; Heating oven for hot air, model HJGF101-4, MFG 2020; Extrusion T-mold, model: SUS630, made in Japan, MFG 2020; Forming device, MFG 2020; Winder & slitting system, MFG 2020; Oil free air compressor, MFG 2020; The PP melt blown nonwoven production line is a polymer melt extruded from a screw extruder. The polymer is extremely stretched by high-speed hot air or other means to form very fine short fibers, which are aggregated to A web is formed on a roller or a screen curtain, and is finally reinforced by self-adhesion or thermal bonding. Its unique properties are widely used in mask filter materials, thermal insulation filling materials, medical health materials, wiping materials, etc. The finished product can pass the N95 standard as the core material of the mask. Process of melt blown nonwoven production line Polymer preparation --- Melt extrusion --- Metering pump --- Melt blown die head assembly --- Solution thin-flow drawing --- Fibber cooling --- Auxiliary network --- Electrostatic electret --- Reinforced finished product. Melt-blown cloth is produced by melt-blown process. The equipment mainly includes: screw extruder, melt pump, screen changer, melt-blown device, winding device, air system (hot air blower and heater), etc. The function of the screw extruder is to melt the slice material; the role of the melt pump is to accurately measure, control the output and the fineness of the fiber, and continuously and evenly transfer the melt to the spinneret. The function of the screen changer is to filter out impurities in the melt so as not to block the spinneret holes. The function of the winding device is to pack the melt blown cloth into rolls. The function of the air system (hot air blower and heater) is to provide the temperature and pressure of the hot air used in the drawing of the spinning air stream. Price Euro 39.200 Euro + VAT, negotiable, FCA: Oradea / Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: used, Stretch blow molding machine by Etek ISBM line = Injection stretch blow molding Stretch blow molding machine for single-use PET bottles made from PET preforms Stretch blow molding machine for production using the rotary process Manufacturer: ETEK / GF-Industries, Type Supra 800 sv 1 Serial number: 22000225 Year of manufacture: 2012 Gjdpokucxljfx Afuokc Power: 90 kW Mains connection: 400 volts, 50 Hz Weight: approximately 6000 kg In like-new condition

Condition: good (used), Year of construction: 2017, functionality: fully functional, LINEAR PET BLOWING MACHINE SET with auxiliary equipment AC ARCOR - multiBlow2 - 2017 Speed: 1,5L - 6000 Cavities: 4 Formats: 0,1 - 3,0L Gksdequuvrspfx Afuec AUXILARY EQUIP 1. Chiller - M.T.A S.p.A - TAE EVO 051 2. LOW Pressure compressor - SHAMAL 45kw 3. Receiver tank - Low pressure - MAX 16Bar 4. Receiver tank - High pressure - MAX 45Bar

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, WE OFFER AN NICE WORKING CONDITION UNILOY MORETTI RETROFITED WITH NEW SIEMENS CONTROLS MACHINE IS WORKING DAILY PRODUCTION FOR TECHNICAL AUTOMOTIVE PARTS MACHINE WAS OVERHAULED IN COMPLETE WITH NEW OPERATIONAL SYSTEM IN 2022 MAIN TECHNICAL DATA - Installed power 130 kW - Heater power 32 kW - Auger diameter 70mm - Power of auger motor 45kW Gsdovmd Nwepfx Afuskc - Closing force 150kN - Plate 450x550 - Closing plate opening from 320 to 620mm - Head volume 3l

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 13-13, The BLOMAX 4 Blowmoulding machine is of the model 13-13. The machine has no defects and operates in excellent condition with full functionality. Power : 400V/150A/60000W Year of construction : 2000 Gkodpfxet Akgwj Afuoc

Condition: used, Year of construction: 1992, Automatic PET bottle blowing machine Manufacturer: SIDEL Type: SBO 4 S1 Year of prod. 1992 Capacity: 4,000 for 1.5 L / 2 L bottles Installed power: 150 kW Includes 1.5 L molds Preform feeder Gkodewa Rhrspfx Afujc Technical condition: used machine, starts up, program is functional

Condition: like new (used), Year of construction: 2022, operating hours: 200 h, functionality: fully functional, screw diameter: 70 mm, overall weight: 600 kg, clamping force: 80 kN, total width: 2,800 mm, total length: 4,000 mm, total height: 2,260 mm, Main Features: 1. Computer Control System (PLC) – Japanese Mitsubishi PLC 2. Electrical Cabinet – All electrical components are sourced from globally renowned brands, ensuring quality and stability. 3. Touch Screen – Innovation computer control system 4. Advanced Hydraulic Cylinder from Germany 5. Linear Guideway 6. ABB Inverter from Switzerland & Rexroth from Germany 7. Large Diameter Galvanized Steel Pipes 8. Electric Lifting Platform 9. Ceramic Heater 10. Hydraulic System & Valve Connections – From Yuken Industry Technical Specifications: • Suitable Material: PE, PP, and others • Max Volume: 6 L • Production Capacity: 170-260 pcs/h • Dimensions: 4.0 × 2.26 × 2.8 m • Weight: 6T Plasticization System: • Reducer: Hard finishing, high strength, low noise • Screw: Ø 70 mm, L/D ratio 24, 38CrMoALA, cooling system available • Plasticization Capacity: 100 kg/h (HDPE) • Heating Zones: 3-4 aluminum heaters, automatic heating • Heating Power: 12 kW/h • Extruder Motor: Three-phase asynchronous motor (380V, 50HZ) • Cooling Fan: 4 zones, automatic cooling Extrusion System: • Material: High-grade alloy steel, central feeding • Number of Die Heads: 1 • Max Die Mouth Diameter: Ø 160 mm • Heating Zones: 4, stainless steel heating cycle • Heating Power: 5-7 kW Clamping System: • Features: High strength, rigidity, central mold locking, stable mold opening & closing • Clamping Force: 80KN • Template Distance Adjustment: 170-520 mm • Max Mold Size: 380 × 420 mm Electric System: • Automatic Monitoring, Fault Alarms, Auto Counting, Auxiliary Functions • Control Interface: Touchscreen with self-diagnosis alarm system • Temperature Control: Automatic temperature control module • Motion Control: Inovance (Chinese/English version) Hydraulic System: • Features: Multi-functional integrated hydraulic block, proportional control, high efficiency • Oil Pump Motor: Three-phase asynchronous motor (380V/220V, 50/60HZ) • Oil Pump: Imported double pump • Valves: Imported oil pump valves and connections • Oil Pipes: Double-layer wear-resistant • System Pressure: 60 kg/cm² • Cooling System: Separate water cooling cycle, oil cooler Pneumatic System: • Brand: Taiwan AIRTAC pneumatic system • Air Pressure: 0.6 MPa • Air Displacement: 0.8 m³/min • Electromagnetic Valve: Taiwan AIRTAC Main Components: Electronic Parts: • PLC Control System: MITSUBISHI from Japan • Touch Screen: INOVANCE • Temperature Controller: HUICHUAN • Auxiliary Relay: OMRON • Contactor: Schneider from France • Electric Motor: Three-phase 380V • Power Source: TAIWAN MEANWELL • Transducer: ABB from SWITZERLAND Gkjdpfjv Iflpjx Afusc Hydraulic Parts: • Oil Pump: TAIWAN HIGH-TECH • Valve: YUKEN • Oil Pump and Connection: YUKEN • Sealed Part: HALLITE Air Control System: • Cylinder: AIRTAC • Air Valve: AIRTAC This blow molding injection machine was purchased directly from a factory in China for a specific project that was never realized. The machine was used for only one month. Location: Siemianowice Slaskie, Poland We also have peripheral equipment available for sale, such as: • 5 HP AIR COOLING SYSTEM • Auto Loading • 150 kg Color Mixer • Scraps Crusher

Condition: good (used), Year of construction: 1998, operating hours: 89,340 h, functionality: fully functional, screw diameter: 90 mm, overall weight: 16,000 kg, clamping force: 650 kN, total width: 2,750 mm, total length: 5,600 mm, total height: 3,200 mm, Manufacturer: Sterling Model: 15 LBS Year of manufacture: 1998 Operating hours: 89,340 h Closing force: 650 kN Screw diameter: 90 mm Gjdpfx Afjzfxwijuokc BM Sterling APV, year of manufacture 1998 Complete control system replacement in 2008 with MACO-sys 6000, performed by Davies-Standard LTD Net price: 45,000 EUR

Condition: excellent (used), Year of construction: 2013, operating hours: 200 h, functionality: fully functional, screw diameter: 65 mm, overall weight: 9,000 kg, clamping force: 785 kN, total width: 1,800 mm, total length: 4,500 mm, total height: 3,000 mm, power: 0.045 kW (0.06 HP), We offer for sale a slightly used injection blow moulding machine in excellent condition. It is connected and fully operational for demonstration purposes. We can also offer several ready-made molds for canisters and lamp shades. The machine is designed for use with PMMA, PC, PP, and PE resins. Gkedpfsthk Rzex Afujc

Condition: good (used), Year of construction: 1994, functionality: fully functional, Manufacturer: S.P.A Magic M.P. Gedpfx Aexxp Tbefuekc Model: MGL2D This blow molding machine is fully functional. It is still in production and can be inspected by appointment. Videos can be provided upon request. PRICE REDUCTION!!! From 21,000 to 19,000 EUR!

Condition: ready for operation (used), Year of construction: 1993, functionality: fully functional, product height (max.): 380 mm, workpiece diameter (max.): 130 mm, production capacity: 7,200 unit/h, TECHNICAL DETAILS Number of cavities: 6 Capacity with standard bottles: up to 7,200 bph Product formats Bottle volume: 0.25 – 3.0 L Max. bottle height: 380 mm Max. bottle diameter: 130 mm Preform dimensions Max. preform length: 210 mm Neck inner diameter: 34 mm MACHINE DETAILS Dimensions & Weight Blow module dimensions: 2,000 x 2,200 x 2,200 mm Blow module weight: 8,000 kg Oven dimensions: 3,000 x 1,100 x 2,100 mm Oven weight: 2,000 kg Control cabinet dimensions: 1,500 x 1,000 x 2,100 mm Control cabinet weight: 1,000 kg Transformer 415V / 380V dimensions: 1,000 x 500 x 2,000 mm Transformer weight: 500 kg Preform hopper and conveyor dimensions: 3,000 x 1,500 x 3,500 mm Preform hopper and conveyor weight: 600 kg Preform feeder dimensions: 2,000 x 2,500 mm Preform feeder weight: 250 kg Infeed guide rail length: 2,000 mm Power supply Total power: 142 kW Mains connection: 380/420 V +/- 10%, 50 Hz +/- 1% Gsdpfxox A Uu Ee Afuskc Cooling water Cooling capacity: 16,000 kcal/h Water temperature: 10 – 12°C Flow rate: up to 6.0 m³/h Water pressure: 5 – 6 bar Compressed air Service air pressure: 7 bar Service air flow: 50 – 100 Nm³/h Blowing air pressure: up to 35 bar Blowing air flow for 0.25 – 3.0 L: 155 – 770 Nm³/h EQUIPMENT Transformer 415V / 380V Preform hopper and conveyor Preform feeder Infeed guides Adaptation to other voltages possible

Condition: good (used), Year of construction: 2005, Ref. no.: 16369 Manufacturer: BATTENFELD Type: EM 75-120 Unilog B4 All-electric Year of construction: 2005 Clamping unit Clamping force: 75 ton Opening stroke: 800 mm Gksdjwl Rucopfx Afuoc Distance between tie bars: 405 x 405 mm Mould height min.: 150 mm Mould height max.: 480 mm Injection unit Screw diameter: 18 mm Injection volume: 30 cm³ Shot weight: 27 g Injection pressure: 2440 bar Measurements and weight Dimensions: 4,5 x 1,7 x 2,0 m Machine weight: 4500 kg Further information: BATTENFELD EM 75/120 UNILOG B4 All-Electric Precision Injection Moulding Machine The BATTENFELD EM 75/120 UNILOG B4 is a high-quality Austrian-made all-electric injection moulding machine. The BATTENFELD EM series was considered one of the most advanced servo-electric machine concepts of its time and was specifically designed for energy-efficient and highly precise production processes. All major machine movements are driven by modern servo motors, providing: * very low energy consumption * high repeatability and precision * smooth and quiet machine operation * low maintenance requirements * stable and accurate production performance The machine is especially suitable for: * technical plastic components * electronic parts * precision moulded products * small and medium-sized production runs Compared to conventional hydraulic machines, the all-electric technology offers significantly improved energy efficiency and process stability. Equipped with the reliable BATTENFELD UNILOG B4 control system, the machine provides: * user-friendly operation * precise process control * stable cycle times * accurate servo axis management The machine has approximately 69,094 operating hours and appears to be in clean and well-maintained condition. The photos clearly show: * a clean electrical cabinet * well-maintained mechanical components * properly kept servo-electric units * a clean injection unit The BATTENFELD EM 75/120 UNILOG B4 is a reliable and energy-efficient solution for demanding plastic injection moulding applications.

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, Equipment: documentation/manual, For sale: Complete PET bottle blowing line TES BluLine4 HiTech MultiFlex (2017) We offer for sale a complete PET bottle production line from the renowned manufacturer TES Sp. z o.o., model BluLine4 HiTech MultiFlex, manufactured in 2017. The machine is in very good technical condition, regularly used, and ready for further operation. Technical data Manufacturer: TES Sp. z o.o. Model: BluLine4 HiTech MultiFlex Year of manufacture: 2017 Bottle capacity range: 0.5 l – 4 l Number of cavities: 2-4 The line includes: ✅ Preform feeder ✅ PET bottle blowing machine ✅ Bottle packer for trays Advantages of the equipment Gkedpfxszd Sb So Afusc Complete and ready-to-use production line Universal range of produced capacities Solid construction and proven TES technology Very good technical condition Ideal for manufacturers of beverages, water, household chemicals, and other products packaged in PET bottles Price: negotiable. If you have any questions or would like to obtain additional information, please contact us by phone or private message. We will gladly provide detailed information and send additional photos of the equipment.

Condition: good (used), Year of construction: 2001, Ref. no.: 18092 Manufacturer: ENGEL Type: ES 1350H 200W / 300HL-2F Year of construction: 2001 Clamping unit Clamping force: 300 ton Opening stroke: 855 mm Platen size (h x v): 1050 x 650 mm Injection unit Screw diameter: 60 +35 mm Injection volume: 735 +135 cm³ Shot weight: 662 + 122 g Injection pressure: 1834 +1620 bar Measurements and weight Dimensions: 7,75 x 2,35 x 2,6 m Machine weight: 24780 kg Further information: ENGEL ES 1350H200W/300HL-2F — 2K Injection Moulding Machine This machine from the prestigious Austrian manufacturer ENGEL, built in 2001, features a clamping force of 300 tonnes and a true 2K L-configuration in horizontal layout. Motor and Hydraulic System Gjdpfx Afjwm Iy Ejujkc The machine is equipped with a powerful electric motor coupled to a high-pressure hydraulic pump group. The electric motor continuously drives the hydraulic pump, providing pressurised oil flow throughout the entire system. This pressurised oil feeds the clamping cylinder, the injection pistons of both units, and the ejector system. The thick red hydraulic hoses visible behind Unit B carry this high-pressure oil flow — both units are supplied via independent hydraulic circuits, allowing Unit A and Unit B to operate simultaneously without influencing each other. Operating Principle The two independent injection units are positioned at 90° to each other — in an L-shape. The mould is locked with 300 tonnes of clamping force. Unit A injects the primary material into the mould at 1834 bar. Immediately afterwards, Unit B injects the second material or colour from a 90° angle into the same mould at 1620 bar. The two materials bond at a molecular level inside the mould, cooling is completed and the ejectors push out the finished 2K part as a single piece. No gluing, screwing or assembly is required — two materials emerge as one single part in a single cycle. Applications Automotive interior and exterior trim parts, large technical plastic components, parts combining a rigid body with a soft grip surface, two-colour large-surface parts.

Condition: ready for operation (used), Year of construction: 1970, operating hours: 1,362 h, functionality: fully functional, machine/vehicle number: 9286, planing width: 600 mm, Planer machine Kupfermühle 5 spindles: bottom / top / right and left / bottom We have produced castle floorboards with this machine, and it was operational until the end. The machine can be demonstrated. Gedpfjyyvuwsx Afuekc Due to its age, it is sold without warranty or guarantee.