Low-bed trailer with removable telescopic gooseneck, 3 steered axles

Nooteboom 53/3

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually Ppodpetx Nwnjfx Afget * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: used, Year of construction: 2008, Extendable superstructure: Yes Production country: DE Please contact Theo Lelie for more information Pjdpoxixpajfx Afgept

Condition: excellent (used), axle configuration: 3 axles, permissible axle load (axle 1): 10,000 kg, permissible axle load (axle 2): 10,000 kg, permissible axle load (axle 3): 10,000 kg, first registration: 06/2018, loading space length: 7,000 mm, loading space width: 2,550 mm, total length: 11,000 mm, total width: 2,550 mm, suspension: air, tire size: 265/70/19.5, color: blue, Year of construction: 2018, Equipment: ABS, = Additional Options and Accessories = - Lift axle - Air suspension = Further Information = Axle configuration Brakes: Drum brakes Suspension: Air suspension Rear axle 1: Tyre size: 265/70/19.5; twin tyres; lift axle; max. axle load: 10,000 kg; steered Rear axle 2: Tyre size: 265/70/19.5; twin tyres; max. axle load: 10,000 kg; steered Rear axle 3: Tyre size: 165/70/19.5; twin tyres; max. axle load: 10,000 kg; steered Ppodpfx Afewifrdoget Weights Unladen weight: 12,000 kg Payload: 36,000 kg Gross vehicle weight: 48,000 kg Functional Loading platform height: 95 cm Condition Technical condition: very good Visual condition: very good EMTECH 3-AXLE LOWBED TRAILER SAF AXLES TRIDEC STEERING SYSTEM AIR-SUSPENDED, STEERED 1 AXLE IS LIFT AXLE 10,000 KG PER AXLE TECHNICALLY PERMISSIBLE GROSS WEIGHT 48,000 KG TYRE SIZE 265/70 R19.5 LOADING PLATFORM LENGTH 700 CM EXTENDABLE 515 CM LOADING PLATFORM WIDTH 255 CM LOADING PLATFORM HEIGHT +/- 95 CM LASHING EYES AND STAKE POCKETS

Condition: used, maximum load weight: 51,870 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, first registration: 03/2025, next inspection (TÜV): 03/2026, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Complete equipment details available upon request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, length approx. 3,700 mm, rear with chamfer approx. 1,000 mm x 10° * For tractors: 4 x 2, 6 x 2, and 6 x 4 * Plug-in steel front wall, approx. 400 mm high * At the front connection strip: yellow-red air couplings * ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for hydraulic operations * External beams of the gooseneck with mounting holes for bolted lashing rings * One mounting hole at the rear upper part of the gooseneck external beam for a bolted lashing ring * 1 pair of screw-in lashing rings included (LC 10,000 daN) * On the gooseneck, 1 pair of plug-in side aluminum drop sides, approx. 400 mm high, anodized version * On the gooseneck, 1 plug-in aluminum rear wall, approx. 400 mm high, anodized version * Approx. 40 mm thick hardwood flooring above the gooseneck * 2-inch kingpin * Gooseneck guide plate for fifth wheel, approx. 500 mm wide * Rear gooseneck mounting for aluminum ramps * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) Ppsdpfx Afjxtc Uhogst LOADING PLATFORM * Loading platform, extendable version, length approx. 8,800 mm, rear with chamfer approx. 500 mm x 10° * Recess in the platform and chamfer for accommodating the excavator dipper stick approx. 2,490 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension * 1st and 2nd axle fixed, 3rd and 4th axles steering trailing axles * 3rd and 4th axles with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with raise and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Complete platform and interrupted between the axles with approx. 50 mm thick hardwood flooring (increasing the coefficient of friction) * Platform locking with conically welded locking profiles every approx. 250 mm * Elongated slots for insertable and repositionable bridging elements at the front of the platform * Intermediate table with set-down platform, approx. 300 mm wide, for large cross-section telescopic tube with sheet metal covering – front and rear with elongated slots for insertable and repositionable bridging elements – removable cover flush with the platform * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 6 pairs of flush-mounted lashing rings in the outside frame of the platform, foldable outward (LC 10,000 daN) * Additionally, 1 pair of lashing rings externally on the front cross member of the platform, approx. 90° turned inward towards the platform (LC 10,000 daN) * Extendable galvanized widening extensions by approx. 230 mm per side * 1 pair of permanently installed wheel recesses, open up to the extension, approx. 700 x 410 mm (W x D), sheet-covered in the platform ahead of the 1st axle, wheel recesses with square climbing strips approx. 15 x 15 mm, spaced approx. 200 mm * Between the 2nd and 3rd axles, 1 pair of permanently installed wheel recesses on the platform, approx. 1,695 x 700 x 410 mm (L x W x D), covers for wheel recesses split lengthwise, with wooden overlay, outer plug-in loc

Condition: used, mileage: 447,091 km, power: 427 kW (580.56 HP), first registration: 02/2018, fuel type: diesel, overall weight: 37,000 kg, axle configuration: > 3 axles, brakes: retarder, color: red, gearing type: automatic, emission class: euro6, Year of construction: 2017, Equipment: ABS, air conditioning, Internal vehicle no.: MK300019 German vehicle More INFO at * Luis Lucena (German, English, Spanish, French) * Viktoria Sologubova (Polish, Russian, Ukrainian, English) Flatbed dimensions: 6,000 x 2,400 mm HIAB superstructure with crane The body is removable, allowing for the installation of a standard or tipper trailer. The hydraulic system is located at the rear. Very nice and well-maintained truck! All functions work perfectly! Lifting moment: 355 kNm 3 m – 12,000 kg 4.9 m – 7,600 kg 6.5 m – 5,500 kg 8.4 m – 4,050 kg 10.2 m – 3,200 kg 12.2 m – 2,580 kg 14.3 m – 2,160 kg 16.5 m – 1,840 kg 18.4 m – 1,580 kg 20.2 m – 1,360 kg Financing example: * Internal number: MK * Purchase price: €119,900.00 * Down payment: 10% Pedpfoyndlxex Afgopt * Term: 60 * Monthly installment: €1,831.54 * Final payment: €23,380.00 If this offer suits you or you would like it adjusted to your requirements, please contact us (Mr. Enchev). We look forward to your call. Errors and omissions excepted. We are happy to accept your used vehicle in part exchange. Financing available directly from us. GOLEC NUTZFAHRZEUGE GMBH We speak: German, English, Spanish, Polish, Ukrainian, Russian, Bulgarian.

Condition: new, machine/vehicle number: df15479123e15bcf265d560e1, empty load weight: 12,800 kg, maximum load weight: 44,200 kg, overall weight: 57,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Aluminum side collision protection 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Telescoping Central tubular frame in neatly welded telescopic frame sections that run into each other. Extendable by max. 6,000 mm and can be arranged approx. every 1,000 mmPayload/point load is reduced when extended! Locking mechanism with mechanical bolt lock With sliding table Low loader lashing eyes 2 pairs of ring lashing eyes each 5to at the front on gooseneck 11 pairs of lashing mushrooms at the top and at the side embedded in the outer frame each 10to 2 x on gooseneck 9 x in low-loader bed distributed first lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between the lashing eyes not greater than 1100 mm 8 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 3 pairs of additional hinged lashing eyes embedded in the low bed, 10 to each1x at the start of the low bed, 1x in front of the 1st axle and 1x behind the 3rd axle Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Last 2 axles self-steering, with automatic reversing lock via reversing light and manual locking function via hand button on the vehicle. Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17.5 Fulda tires Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Ppedpfxsi Ri Hno Afget 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable sockets at the front, without connecting cable Floor Gooseneck with steel / checker plate covering Storage box recessed in drive-over slope to gooseneck Then with 70 mm softwood floor, steel / checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Drop sides 25 mm hollow aluminum profile, 400 mm high, front and side on gooseneck, pluggable Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle Hydraulic connection w