Baler

Presona AB LP 80 VH1

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: Fedpfju Thhrjx Aa Nsgi General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: ready for operation (used), Baler Hsm 155 VL Bale dimensions L x W x H: 1100 x 700 x 700 - 950 mm Bale weight: 2000 - 250 kg (Cardboard) Technical data: L x W x H: 1470 x 940 x 2259 / 2439 mm Weight: 950 kg Pressure force 16 tons Power supply: 400 V (three phases) Motor power: 4 kW Bale ejector Hsm 155.1 VL baler pressure force 18 tons Price of Hsm 155.1 VL baler - 2600eur Hsm 155.2 vl baler Fgjdsra Nrmopfx Aa Noi pressure force 16 tons Price of hsm 155.2 vl baler - 2800eur

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Fgedpfx Aajvwlqqo Noi Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 2012, power: 264 kW (358.94 HP), Stationary shredder M&J 4000S. Electric drive: 2x 132 kW 400 V AC, 50 Hz Inkl. substructure, hydraulic unit, control cabinet. Fgjdpju Dkf Dsfx Aa Nsi

Condition: excellent (used), Year of construction: 2013, operating hours: 11,347 h, functionality: fully functional, machine/vehicle number: 50433-115-4291, Power supply: Voltage 400 V AC, 50 Hz, Main motor power 2 X 200 kW, Main switchboard, rated current 760 A. Main motor, full load current 2 x 341 Amp, PLC controller. Drive principle, hydrostatic transmission with power consumption limiter. Working, cutting cassette: 2 asynchronously operating shafts. Speed ​​33 rpm. Number of rotary knives 2 x 12 pieces, number of lower, fixed knives 2 x 24 pieces. Bearings 2 x 2 barrel. Drive system after general renovation - pumps, engines. The M&J waste shredder is an ideal solution for shredding various types of waste, industrial, municipal. The waste is shredded using one or two rotating shafts equipped with spirally mounted knives, which ensures optimal shredding of the material. The waste shredder is equipped with a fully automated control system that monitors the device's operation and protects it from overload. The device consists of modules, which is why it is a very flexible solution. Fgsdpfxjh Nu Tvj Aa Noi

Condition: excellent (used), Year of construction: 2014, operating hours: 37,656 h, functionality: fully functional, pressing force: 85 t, filling opening width: 1,500 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 650 kg, overall weight: 25,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2024, volume flow: 410 m³/h, transport width: 2,400 mm, transport length: 9,300 mm, Hello, We are offering you a used baler from the manufacturer Presona AB, type LP 85 VH1, subject to availability. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot guarantee their accuracy or completeness. Manufacturer: Presona AB, Sweden Type: LP 85 VH1 Year of manufacture: 2014 Total operating hours: 37,565 hours, as of March 2025 Main press force: 85 t Specific press force: 100 N/cm² Pre-press flap force: 28 t Feed chute dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Fgodpfx Aev T I Evoa Nsi Tying system: 5-fold vertical Hydraulic oil tank volume: 1,000 L Press dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Press weight: approx. 25 t Note: The machine was used for compaction at a recycling plant. Used for the production of paper, cardboard, films, and plastics such as bottles, buckets, canisters, and drums. The press is in good condition. Many wear parts and entire assemblies have been replaced over the past three years. The machine has been regularly serviced. We would be pleased if this press is of interest to you. Your service team at Mertens & Frowein GmbH

Condition: ready for operation (used), Technical specifications of Dixi 60 AUTOMAT baler Filling opening (W x H): 1550 x 1000 mm Drive power: 31.5 kW Pressing force: 60 t Bale weight (depending on material): 350–600 kg Bale dimensions (W x H x D, adjustable): 1100 x 800 x 300–1600 mm Fodpfx Aasv Amw Ns Njgi Pressing/cycle time: 13/24 s Machine weight: 7000 kg

Condition: like new (used), Year of construction: 2024, functionality: fully functional, pressing force: 30 t, Used Bramidan B30 baler. Newly repainted. Ready for use, fully equipped, in perfect working condition. New oil. Fgsdpfxsviymwo Aa Nji

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: HSM-300034869, pressing force: 55 t, filling opening width: 650 mm, filling opening length: 1,195 mm, bale length: 1,200 mm, bale width: 780 mm, bale height: 1,200 mm, bale weight: 480 kg, total width: 1,247 mm, total height: 2,985 mm, total length: 1,797 mm, type of input current: three-phase, input voltage: 400 V, overall weight: 2,010 kg, transport height: 2,168 mm, power: 4 kW (5.44 HP), year of last overhaul: 2025, Brand: HSM The stated price is exclusive of VAT, ex works, and excluding packaging. The press has been cleaned and tested for functionality. Technical Details: Manufacturer: HSM Type: V-Press 860 plus Bale size (LxWxH): 1200 x 780 x 1200 mm Bale weight: 480 kg External dimensions (LxWxH): 1797 x 1247 x 2985 mm Transport height: 2140 mm Feed opening: 1195 x 650 mm Pressing pressure: 548 kN Throughput: 1 - 2 bales / hour Number of wire channels: 4 Press weight: 2,010 kg Power supply: 400 V / 50 Hz Power consumption: 4 kW Installation location: Indoors / outdoors, covered Serial number: 300034869 Year of manufacture: 2009 Fgjdpjvpfw Uefx Aa Nei Please refer to the original documentation, which can be obtained directly from the manufacturer.

Condition: reconditioned (used), power: 11 kW (14.96 HP), operation weight: 8,000 kg, Horizontal baler DIXI 80 SLD 2018-2021 Year of construction Fsdpfoqa Dq Djx Aa Nsgi Semi-automatic 80-tonne baling system for the economical volume reduction of residual materials (recyclables) in industry and trade: Cardboard packaging Tetra packaging Films PET bottles Foam Insulation boards and other compressible materials. Machine dimensions L x H x W approx. mm: 4,320 x 1830 x 2,154 mm Filling opening W x H (standard) mm: 1,040 x 1,110 mm Machine weight approx. kg: 8,000 Press force max. kN: 80 t / 800 kN Ironing cycle (average value) approx. s: 35 Bale size W x H x L approx. mm: 1,120 x 1,120 x 1,200 Bale weight (depending on material) approx. kg: 550 - 650 Binding: manual Number of bindings: 4, with wire with Quicklink wire Drive power: 11 kW; 400V/32A The presses are tested and functional and are offered with a fresh UVV and inspection in accordance with DGUV regulation 3. The Dixi 60SLD is ready for immediate use. On request, the Dixi 60 SLD can be completely overhauled for an additional charge. This includes: Replace all hydraulic hoses. Change the hydraulic oil and check the hydraulic unit. The hydraulic cylinders are checked and replaced if necessary. Net price plus VAT and possible transportation. The operating instructions are available and are supplied as a PDF file and in paper form.