Used Mütek Ballenauflöser for sale (51)

Condition: new, Year of construction: 2026, Actually one showroom machine available. Very robust machine with high pressing force - is also suitable for producing a salable briquette quality * depending on the material. The large press cylinder and the 80 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Surcharge for cooling unit + € 4.995 net, (can also be retrofitted later) * cools the pressing tongs (important from 3.5 hours) and the hydraulic oil * Cooling device recommended for regular use of more than 3.5 hours at a time. Briquette diameter: 80 mm Front bush: 125 mm Briquette stroke max .: 100 mm Briquette lift opt ​​.: 80 mm Output (depending on material): up to 200 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter Motor power: 9.2 kW 400 volts / 50 Hz / 3 phases Length: 2095 mm Width: 1300 mm Height: 1700 mm Weight: 1250 kg Oil volume: 220 liters Silo diameter: 1200 mm Silo content: approx. 1 qbm Isdpjxfwdefx Ag Aetn Pump: 75 liters Hydraulic pre-compressor Cooling pressing tongs option: yes, with special accessory coolable pressing tongs Hydraulic oil cooling option: yes Cooling of the pressing tongs and the hydraulic oil with cooling device (special accessory) Level monitoring option: yes Strand briquette option; yes (depending on material) Option of enlarged filling slide: yes, with special accessory enlarged filling slide CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Chip length maximum 20 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: new, Year of construction: 2026, Single-shaft shredder MRZ 530 Included: Eco Ring Rotor (for reduced energy consumption) Options: Veneer and paper scraper + €970 net * recommended for extremely thin materials with a thickness of less than 3 mm Our mütek single-shaft shredder MRZ 530 shreds a wide variety of materials such as residual wood of all kinds, softwood, chipboard and hardboard, pallets, construction lumber, demolition wood, carpet, cables, paper, cardboard and plastics. The machine is characterized by a robust design that guarantees consistent quality in continuous operation. We would be happy to offer you a free test with your material. We invite you to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material by freight forwarder, and we will document the test with pictures and videos. Itedpfxod Db N Io Ag Aen Machine data: Motor: 11 kW; 400 V - 50 Hz - 3 phase, Knives: multi-reversible, Rotor diameter: 260 mm, Control: Siemens S7-1200 PLC, Hopper (mm) 510 x 810 mm, Hopper volume approx. 0.4 m³, Hydraulically operated slide, Screen size optional (10 - 40mm), Suction nozzle Ø 160 mm, Weight approx. 1,000 kg, Dimensions approx. 1550 x 1100 x 1640 mm, Moisture content of the raw material: must be below 30% (dry basis). Standard included: • Fast hydraulics • Profile rotor • Control cabinet with Siemens PLC control • Automatic star/delta start • Automatic OFF when the rotor is idling • Removable suction channel • Speed 70 - 100 RPM for higher throughput • Cycle control to avoid idle times • Performance-enhancing step control of the hydraulic slide • Stable guides for the hydraulic slide Further shredder options: - Raise the shredder by 30 cm (preparation for conveyor belt) + €1,980 net - Inclined conveyor belt + €8,770 net Horizontal section: 1200 mm Inclined section: 2500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2000 mm + - 100 mm - Over-belt magnet + €5,980 net - Control for conveyor belt and over-belt magnet + €2,750 net (Start and stop synchronized with the shredder) Requirements for the input/raw material: - The moisture content (dry basis) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear.

Condition: good (used), Year of construction: 2001, Good, used condition. Few operating hours (1,675 hours). Engine: 11 kW Pressure: adjustable up to a maximum of 250 bar Throughput: up to a maximum of 200 kg/h Briquet: 150x60 mm Dimensions of the press: approx. 2200x3000x1920 mm (L x W x H) Dimensions of the control cabinet: Iedpfxjwcc D Rj Ag Astn 500x1250x2120 mm (L x W x H) Weight: approx. 3000 kg

Condition: new, Year of construction: 2026, Production time appr. 4 months Our best-selling briquetting press series + Tried and tested, simple technology for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several hundred machines in use with satisfied customers + Good price performance ratio Throughput approx. Up to 200 kg per hour * strongly dependent on the material. - in the last test with aluminum granules smaller than 5 mm - approx. 186 kg per hour + the pressed emulsion. - in the last test with aluminum chips smaller than 18 mm - approx. 120 kg per hour + the pressed emulsion. Technical specifications: Motor: 7.5 KW + 0,55 kW Cooler 400 volts / 50 Hz / 3-phase, Front bush: 125 mm, Briquette stroke max .: 100 mm, Briquette stroke opt .: 80 mm, Pump: 80 liters, Storage container approx. 0.5 qbm content (expandable), Diameter: 1200 mm, with agitator discharge, Hydraulic unit complete with oil tank 220 liters Dimensions approx. 2095 x 1600 x 1310 mm lxwxh, Weight 1370 kg, Automatic on-off switching via level indicator CE compliant. . Requirements for the raw material: - Chip length maximum 20 mm Itodpfx Agochqxxj Asn - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of magnetic metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: good (used), Wood shredder for sale Prepared for conveyor belt removal Ideal for shredding wood residues (all types of softwood) and pallets Includes hydraulic pusher Motor: 7.5 kW Rotor width: approx. 82 cm Weight: 1,460 kilograms Full load current: 32 amp Main fuse: 35 amp Iodpsxbyx Tsfx Ag Astn

Condition: good (used), Technical data: Briquetting press RUF RB 440 Press capacity when pressing wood: up to a maximum of 440 kg/hour Material moisture: maximum 15 % Motor power: approx. 30 kW Briquette size; rectangular: 150 x 60 mm Length: 40 - 110 mm Itedpfxjt H D Ezs Ag Asn Dimensions approx. 1680 x 1800 x 2000 mm Weight: 3000 kg

Condition: new, Year of construction: 2025, The ideal machine for shredding hardwood and softwood. Another machine, available immediately (ex works Neckartailfingen). Motor: 18.5 kW; 400 V - 50 Hz - 3 phase, Knives: 14 + 2 pieces, 40x40mm, can be rotated multiple times, Rotor diameter: 260 mm, Control: Omron PLC, Cutting chamber opening: 600 x 800 mm, Hopper volume approx. 0.6 m³, Hydraulically operated slide Screen size optional (12 - 40mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (l x w x h) approx. 1737 x 1167 x 1650 mm The following options are available at an extra cost: - Additional knife row + €1,990 net (28 instead of 14) - Surcharge for four-sided segment bottom + €2,170 net (prevents the slide from jamming. Recommended for materials with a thickness of less than 3 mm) - Raise the shredder by 30 cm (preparation for a conveyor belt) + €1,980 net - Inclined conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overband magnet + €5,980 net - Control system for conveyor belt and overband magnet + €2,750 net (start and stop synchronized with the shredder) Ijdpfx Aged E R D Se Ajtn - Special bearing + €1,540 (rarely needed. Enclosed, even more stable rotor bearing. Possibly worth considering for sieves smaller than 15 mm or with a high proportion of fine material. If the bearings are lubricated with grease, this is not necessary if operated approximately every 2 weeks) Requirements for the raw material: - The moisture content (dry basis) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear. We would be happy to offer you a free test with your material. We invite you to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material by freight forwarder, and we will document the test with photos and videos.

Condition: good (used), Good, used condition. Iodpfx Agst Hxudo Aetn Main motor: 11 kW Throughput up to a maximum of 200 kg/h Year of manufacture: 12/2008 Briquet: 150x60 mm *Used machine, sold as is. Functional guarantee upon delivery.

Condition: new, Year of construction: 2026, production time appr. 4 months * for suction perception, see picture 4 and 5 Tariff number: 84659600 Main motor: 55 kW; 400 V - 50 Hz - 3 ph including turbo coupling, Hydraulic motor: 2.2 kW, 400 V - 50 Hz - 3ph Knife: 76 pieces, rotatable Knife size: 35 x 35 x 20 mm Rotor diameter: 360 mm Control: PLC Siemens S7-1200 Funnel opening approx. 1530 x 1235 mm Hopper volume approx. 2.5 square meters hydraulically operated slide Screen perforation: 10 - 30 mm Extraction nozzle Ø 200 mm Weight approx. 4,500 kg Dimensions (lxwxh) approx. 2765 x 2520 x 1730 mm Turbo coupling Included as standard: - V-rotor for other throughput - 2nd row of knives on the rotor - Control cabinet with Siemens PLC control - automatic star / delta start - fast hydraulics - Automobile. OFF when the rotor is idling - Speed ​​70-90 rpm for high throughput - Clock control to avoid idle times - Performance-increasing step control of the hydraulic slide - Pertinax guides for hydraulic slides - anti-vibration machine feet - CE conformity The shredder is for shredding natural wood, chipboard and MDF board other materials after testing and approval by the manufacturer Recognition from the raw material: - The moisture content (atro) must be below 30% Isdpfx Agjd Hkqho Ajtn - Metals and mineral impurities such as sand, stones, etc. Interests to interests wear

Year of construction: 2026, condition: new, to sell the demonstration machine at a special price Iodpfjd N Dn Dex Ag Astn Our MVZ 7.5 granulator is suitable for shredding thin-walled parts and/or for post-shredding wood chips. More details after a test with your material. Larger systems are also available as an option The price is only for the shredder as shown in picture 1 - fan, cyclone and filter are options. Motor: 7.5 kW *larger systems on request (4 to 75 kW) Throughput up to 120 kg/h *depending on screen and material Much higher throughput rates can be achieved with the secondary shredding of wood chips. Details after the test with about 30 kg. Rotor diameter: 180 mm 6 rotary knives each 225 mm 4 stationary knives each 225 mm Dimensions: 930x730x1420mm weight: 450 kg, suction nozzle: 100 mm, Screens: 6.8 and 15 mm - other screens available, Price per sieve: €390. Price set replacement knife: 579 € Suitable e.g. fur: - Plastic waste of all Art.-No Various materials - HDPE, LDPE, PP, PS. PC, PA - biomass -Wood - Herbs etc. Parts from injection molding, blow molding, injection molding scrap, small bottles, cables, small pipes, profiles, etc

Condition: good (used), Technical specifications: Briquetting press in good condition Isdpjwtdk Tjfx Ag Ajtn Year of manufacture: 2007 Technically inspected in 06 / 2025 Cylindrical briquette: 80 mm Throughput up to max. 150 kg/h *only approx. 3,949 operating hours - Hydraulic press: briquetting press with discharge chute - Hydraulic unit: 4 kW - Pressure: max. 300 bar - Transport dimensions: 1585/2140/H1940 mm - Weight: 1,370 kg Functional guarantee upon handover We are happy to arrange a free test run!

Condition: new, Year of construction: 2026, Availability upon request. Very robust machine with high pressing force. - Also suitable for producing marketable briquette quality, depending on the material. The large-sized press cylinder and the 70 mm briquette size make this possible. Our best-selling briquetting press series: + Proven, simple technology for extremely low failure rates. + 25 years of experience, continuous development, and know-how. + Several thousand machines in operation with satisfied customers. + Excellent price-performance ratio. Additional cost for demonstration cooling unit: €4,980 net. (can also be retrofitted later) * cools the press tongs (important after 4 hours) and the hydraulic oil. * Cooling unit recommended for regular operation of more than 4 hours at a time. Commodity code: 84793010, Briquette diameter: 70 mm, Front bushing: 125 mm, Briquette stroke max.: 100 mm, Briquette stroke opt.: 80 mm, Capacity (material-dependent): up to 150 kg/h* * depending on the bulk density, * based on a bulk density of 200 kg per cubic meter. Motor power: 9.2 kW, 400 Volts / 50 Hz / 3-phase, Length: 2095 mm, Width: 1300 mm, * with large chamber 1600 mm Height: 1700 mm, Weight: 1250 kg, Oil volume: 220 liters, Silo diameter: 1200 mm Silo capacity: approx. 1 cubic meter Pump: 75 liters Itjdsd Nm Siopfx Ag Aon Hydraulic pre-compressor Optional cooling for press tongs: yes, with special accessory - coolable press tongs Optional cooling for hydraulic oil: yes Cooling of the press tongs and hydraulic oil with a cooling unit (special accessory) Optional level monitoring: yes Optional strand briquette: yes (material-dependent) Optional enlarged feed slide: yes, with special accessory - enlarged feed slide CE compliant Requirements for the raw material: - The moisture content (oven-dry basis) must be between a minimum of 6% and a maximum of 18%. - Chip length max. 20 mm - Installation temperature: temperature-controlled room with a minimum of +5°C - The feed material must be free of metals and mineral contaminants such as sand, stones, etc. Damage to the press tools and/or increased wear may result.

Condition: new, Year of construction: 2025, Ideal for shredding straw, polystyrene, leaves, hay, and bread. Throughput is highly dependent on the screen and the input material: - up to a maximum of 350 kg/h for straw with a 15 mm screen - up to 60 kg/h for EPS with a 15 mm screen Motor: 11 kW - 400 volts, (9.2 kW or 15 kW also possible upon request) Optional: *Additional cost for the next larger machine with 18.5 kW and a larger silo diameter: + €2,750 net Robust steel construction, hardened cutting blades, screen with interchangeable inserts, optionally with (10), 15, 22, 26, 30, 40, or 60 mm perforations For electric drive with star-delta starter, overload protection, and 8 m power cable, ready for connection, Iodpozbizsfx Ag Ajtn discharge spout 150 mm, optionally for plastic or grain pipes, blowing distance approx. 12 m, chassis with 2 running wheels, Ø 380 mm, and one pivoting support wheel, Ø 125 mm, all wheels with solid rubber tires, dimensions approx. 1200 x 900 x 1270/1400 mm (l x w x h) Weight approx. 240 kg, Spare part prices and options: 24 blades, hardened, €9.90 net each 6 bolts, €14.90 net each 1 screen, €475 net Cover, €290 net each Polystyrene disc: €600 net each

Condition: new, Year of construction: 2026, Delivery time approx. 3-4 months Shredder MRZ 830 Commodity code: 84659600 Feed opening 800x1000 mm Motor: 18.5/22 kW; 400 V - 50 Hz - 3-phase Blades: multiple, rotatable Hydraulically operated slide Screen opening as desired (10 - 40 mm) Suction nozzle Ø 200 mm Iodpfx Agsd Dgw Uj Aetn Weight approx. 1,600 kg Dimensions (l x w x h) approx. 2290 x 1420 x 1750 mm Turbo coupling Standard features include: - Automatic star/delta starter - Fast hydraulics - Auto. OFF when the rotor is idle - Speed 70-90 rpm for high throughput - Cycle control to avoid idle times - Performance-enhancing stepped control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant The shredder is designed for shredding untreated wood, chipboard and MDF boards, and other materials after testing and approval by the manufacturer. Additional shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) + €2,140 net - Articulating conveyor belt + €8,770 net Horizontal section: 1200 mm Rising section: 2500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2000 mm + - 100 mm - Over-band magnet + €5,980 net - Control system for conveyor belt and over-band magnet + €2,750 net (Start and stop synchronized with the shredder) Requirements for the raw material: - Moisture content (as received) must be below 30% - Installation temperature: temperature-controlled room at a minimum of +5°C - Metals and mineral contaminants such as sand, stones, etc. will lead to increased wear.

Year of construction: 2026, condition: new, *Only the neodymium overbelt magnet is offered, not the conveyor belt underneath. *Neodymium magnets are among the strongest magnets in the world. They have an extreme pulling power and cannot be compared to ferrite magnets. Extremely high degree of separation, depending on the bulk height and the starting material. Probably the most compact overband magnet on the market. The competition often uses the less powerful ferrite magnets to save costs. dimensions approx. Length: 104cm Width: 22cm Height: 28 cm (at the motor) *Without controller Surcharge for simple manual start/stop control + 495 € A high-performance industrial neodymium magnet is installed. High-performance neodymium magnet approx. 600x68x36.5 mm * So nails are attracted to a length of 600 mm and thrown off to the side, in the area that is no longer magnetic. This overbelt magnet should be mounted approx. 5 - 9 cm above the material flow. *Assembly/suspension on site Ideal for separating nails from wood chips. Optionally also in a single-shaft shredder that is sucked off Itjdpfxsdubpue Ag Aen Requirements: *Your belt width or useful width inside (of the existing conveyor belt) should ideally be narrower than 55 cm *Suitable for separating nails from material flows that are less than 12 mm high and with a chip length of less than 25 mm. ----- Optional at extra charge: Cross and ascending belt demonstrators from € 7,995 net

Condition: as good as new (ex-display), Year of construction: 2023, operating hours: 27 h, one machine directly available *Prior sale expressly reserved Iedpfogbpm Tsx Ag Aotn *Round silo at extra charge Press can only be supplied with a system component such as a chipper, cutting mill, hammer mill, screw conveyor, conveyor belt with overbelt magnet or suction Hydraulic briquetting press for rectangular briquettes Type R - throughput up to maximum 500 kg / h * depending on the specific weight of material. Based on a bulk weight of 220 kg / m³. + 24h operation possible + Longevity + Low maintenance costs + Compact structure + High energy efficiency thanks to innovative hydraulics + 25 years of experience . * depending on the bulk weight of your raw material * based on a bulk weight of 200 kg per cubic meter Detailed information after a successful test with your material . Drive motor: 22 kW - IE 3 400 V / 50 Hz / 3 phases Oil cooler: 2.2 kW Agitator: 0.55 kW Screw: 1.5 kW . Hopper: 400x800mm Capacity of approx. 150 liters . Soft start for hydraulic motor Siemens PLC S7-1200 . Auto start and stop via a light barrier integrated in the feed hopper Up to 560 briquettes per hour . Specific pressing pressure: 1,700 kg / cm² Up to 300 bar pressing pressure Briquette format 150x60 mm Briquette length: 40 to 110 mm (adjustable) Dimensions: 2.9 x 2.0 x 2.1 m Weight: 3,800 kg. 600 liter hydraulic oil tank The control is designed for operation from + 10 degrees to +35 degrees . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 15% - Maximum chip length: 20 x 2 x 2 mm - Installation temperature: temperature-controlled room at at least + 8 ° C Otherwise, we recommend heating for an extra charge - The loading must be free of metals and mineral impurities such as sand, stones, etc. Damage to the pressing tools and / or increased wear can be the result.

Condition: good (used), Clean air extraction system Used machine, in good condition Images to follow mobil Jet 160, Connection 160, Fan 2.2 kW Ijdpferb D Nsx Ag Aetn Air flow rate 1850 m³/h, 400 V

Condition: as good as new (ex-display), Throughput of up to a maximum of 50 kilograms per hour. Briquette diameter: 50 mm. Main motor: 4 kW. Very compact design. Dimensions: 1,100 x 1,500 x 1,200 mm. Weight: 570 kg. Itodpfx Agjzu Skno Aen

Condition: new, Year of construction: 2026, Diameter: 160mm Also available in the diameters: 180, 200, 250, 300 mm for an additional charge, other diameters on request. Very stable industrial design. Ideal for separating nails/metal parts from material flows. For example after a wood shredder. including 3 extremely powerful magnets Itodpfx Agjchuvre Asn * If desired, up to 6 magnets can be installed in the component - surcharge for each additional magnet + 49 € - Neodymium magnets are also available instead of ferrite for an additional charge Your advantages: + Extremely large inspection door with seal for easy stripping of the nails + Stable quick-release fastener +Made in Germany Inspection door / opening: 35x18 cm Installation length may vary

Condition: new, Year of construction: 2026, Machine manufacturing time: approx. 3.5 months Very robust machine with high pressing force - also suitable for producing marketable briquette quality, depending on the material. The large-sized pressing cylinder and the 65 mm briquette make this possible. Our best-selling briquetting press series + Proven, simple technology for extremely low susceptibility to errors + 25 years of experience, continuous development and know-how + Several thousand machines in operation with satisfied customers + Good price-performance ratio Isdpfx Ajffh Atsg Aetn Options: Additional cost for cooling unit: €3,995 net (can also be retrofitted later) * cools the pressing jaws (important for operation of 3.5 hours or more) and the hydraulic oil * Cooling unit recommended for regular operation of more than 3.5 hours at a time. Large pre-compression chamber: €1,975 net Recommended for lightweight raw materials such as wood shavings Commodity code: 84793010 Briquette diameter: 65 mm Front bushing: 65 mm Briquette stroke max.: 50 mm Briquette stroke opt.: 50 mm Performance (material-dependent): up to 110 kg/h* approx. 87 kg/h in the last test. *depending on the bulk density *based on a bulk density of 200 kg per cubic meter. Motor power: 5.5 kW 400 volts / 50 Hz / 3-phase Length: 1925 mm Width: 1100 mm Height: 1500 mm Weight: 800 kg Oil volume: 110 liters Silo diameter: 1000 mm Silo volume: approx. 0.7 cubic meters Pump: 37 liters Hydraulic pre-compressor Option: Cooling of pressing jaws: yes, with special accessories for coolable pressing jaws Cooling of the pressing jaws via water tank (to be provided on site) Option: Cooling of hydraulic oil: yes Option: Level monitoring: yes Option: Log briquettes: yes (material-dependent) CE compliant Requirements for the raw material: - The moisture content (oven-dry) must be between a minimum of 6% and a maximum of 18% - Chip length maximum 15 mm - Installation temperature: temperature-controlled room at a minimum of +5°C - The feed material must be free of metals and mineral impurities such as sand, stones, etc. Damage to the pressing tools and/or increased wear can result.

Condition: as good as new (ex-display), Year of construction: 2024, Pre-crusher Base machine starting from €29,950 net *Options available at an extra charge Ideal for pre-crushing bulky materials such as pallets, planks, beams, fruit crates, polystyrene, plastics, and more. To produce wood chips, the pre-crusher can also be installed directly above a single-shaft shredder. Machine in pre-production *Special options available at an extra charge Your advantages: + Volume reduction of up to 70% + Significantly lower transport costs + Low disposal costs Isdofd Icijpfx Ag Aetn + Production of fuel material + Also ideal as a pre-crusher for a single-shaft shredder to produce wood chips Weight: 1,200 kg Dimensions: 2050x850x1600 mm Cutting head opening: 1300x700 mm *also available optionally in 1600x700 mm (motor then 11 kW) (Extra charge: + €4,995 net) Throughput: up to 50 pallets/pieces per hour *strongly material-dependent Motor: 7.5 kW Options: Industrial hopper attachment (3-sided closed) + €4,950 net Extra emergency/off button + €495 net 200 mm extension + €497 net Requirements for the raw material: - Moisture content less than 30% ATRO - The machine must be installed in accordance with CE guidelines, and measures must be taken on site to prevent access from below (into the cutting head). - Pallets up to a size of 1200x800 mm can be processed. - Longer parts can also be processed vertically.

Condition: new, Year of construction: 2023, Length: approx. 2500 mm Width: approx. 400 mm Discharge height: approx. 1650 mm Weight: 290 kilograms Motor: 0.75 kW Ex works prices Shipping as per effort Itsdpfx Agjv Srvvj Aen

Condition: like new (used), Year of construction: 2024, operating hours: 29 h, *one machine is ready for delivery and ready produced Press can only be supplied with a system component such as a chipper, cutting mill, hammer mill, screw conveyor, conveyor belt with overbelt magnet or suction RUF briquetting press for rectangular briquettes Isdsfhql Topfx Ag Ajtn Very robust and established machine The ideal machine for professional, industrial briquette sellers. Classic type - throughput up to 425 kg / h * depending on the material Options for an extra charge: Plant construction / mütek system technology: - mütek shredder MRZ shredding technology - conveyor belts - Overbelt magnets - Extraction systems, optionally with rotary valve - screw conveyors - silos - Control links of all kinds - semi-automatic packaging technology Press: - Packing table with drawer - Top-mounted silo with discharge Your advantages: Most important point: + Very established, well-engineered die press thanks to 25 years of experience. The difficulty and the know-how lies in the detail. For example, valves and cylinder seals of the highest quality. + 24h operation possible + Longevity + Low maintenance costs + Compact structure + High energy efficiency thanks to innovative hydraulics Technical data briquetting press: Throughput: up to 425 kg / h * * depending on the bulk weight of your raw material * based on a bulk weight of 200 kg per cubic meter Detailed information after a successful test with your material. If no test material is made available to us, we cannot make any statements about the briquette quality and throughput. Briquette dimensions: 150 x 60 mm Briquette length: 40 to 105 mm (adjustable) Hydraulic pre-compressor Main hydraulic compressor Pressing pressure: up to approx. 1700 kg / cm² Hydraulic system with 260 liter oil tank Pump motor: 30 kW / 400V / 50Hz / 3 ph Manual operation of all cylinders "Dustproof" switch cabinet with PLC control and touch display Total power consumption of the briquette press: approx. 33 KW Muxzr8 Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 15% - Maximum chip length: 20 x 2 x 2 mm - temperature where machine is placed + 8 degrees - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear.

Year of construction: 2022, condition: new, Highlights of our two extraction systems Eco 3000 and Eco 5000 +Solid sheet metal construction ensures ideal flow conditions +resistant wind impeller +constant extraction performance even under constant stress + Connection of up to a maximum of 3/4 machines possible using the supplied distributors +high suction power due to large filter surface (filter dimensions: ø500x1100mm) +Integrated driving device for easy manoeuvring Scope of delivery: Running gear, filter and chip bag, distributor (connection for 3/4xø100mm suction pipes), incl ---- Device available in two designs: *in the following marked with position 1) and 2) 1) Extraction system Eco 3000 - 1.5 kW * with a chip bag and an industrial polyester filter Motor power S1 in W 1500 Installation dimensions in mm 985x560x2250 Extraction capacity in m³/h: 3,000 Suction outlets 3x (ø100mm) Negative pressure in Pa: 2200 2) Extraction system Eco 5000 - 2.2 kW * with two chip bags and two industrial polyester filters Motor power S1 in W 2200 Installation dimensions in mm 1540x560x2270 Extraction capacity in m³/h: 5,000 Suction outlets 4x (ø100mm) Negative pressure in Pa: 2600 --- Information applies to both devices: Sound pressure level in dB(A) < 85 dB Voltage: 400V / 50Hz *Option: also available in 230 V Chip bag diameter in mm: 500 Chip bag length in mm: 850 Delivered in a box for self-assembly in a few steps Itjdpfx Aeidma Neg Asn The filters must be cleaned manually at regular intervals. Surcharge for suction with automatic cleaning + €4,700 net

Condition: good (used), Year of construction: 2025, Requirements: - Material must be free-flowing (grain size < 18 mm) - Material must be pure, with an ash content of less than 1% ATRO Note regarding: sand, stones, and minerals - Material is compacted by means of compression tongs - Material must be dry, maximum 15% ATRO New: Innovative combination of briquette and pellet Options available at an additional cost: Plant construction / mütek system technology: - mütek shredder MRZ crushing technology - Conveyor belts - Overband magnets - Extraction systems, optionally with rotary valve airlock - Transport screws - Silos - Control system connections of all kinds Itjdpfxjfbb Are Ag Aon - Semi-automatic packaging technology + 24-hour operation possible + Compact design + High energy efficiency thanks to innovative hydraulics + Briquette density of up to ≥ 1 kg/l possible *Details after testing Operating principle: The machine has a silo with an agitator. In each of the 4 corners of the storage silo, there is a vertical screw that compresses the material downwards into the compression chamber. The machine operates with two cylinders, each of which compresses in two directions (either while the cylinder moves forward or backward). This results in 4 briquette outlets, each with 6 individual briquettes. *ideal for the automatic feeding of the heating boiler Format Ø 30 mm Throughput of up to a maximum of 310 kg/h Motor power: approx. 29 kW (total); approx. 30% less in continuous operation Dimensions: 3.1 x 2.3 x 2.2 m Weight: 3.55 tons Your advantages: Compact briquette/pellet format enables the firing of industrial furnaces by means of screw feed Fully automatic 24-hour operation possible High energy efficiency Briquettes/pellets with consistently high quality and density For automatic feeding into industrial furnaces Small to medium quantities of wood chips, which are produced in the processing industry of various materials (especially wood, biomass, etc.), can be optimally compressed. The small Ø 30mm format represents an attractive alternative. Unlike our conventional briquettes, these can be automatically fed into industrial furnaces. In addition to wood, various other materials can also be easily processed (various biomass and agar-based materials).