Used Blow Moulding Machine for sale (66,360)

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Ksdjg Ailcepfx Ai Rodr Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Bottle capacity 0.25 – 3 liters AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, WE OFFER AN NICE WORKING CONDITION UNILOY MORETTI RETROFITED WITH NEW SIEMENS CONTROLS MACHINE IS WORKING DAILY PRODUCTION FOR TECHNICAL AUTOMOTIVE PARTS MACHINE WAS OVERHAULED IN COMPLETE WITH NEW OPERATIONAL SYSTEM IN 2022 MAIN TECHNICAL DATA - Installed power 130 kW - Heater power 32 kW - Auger diameter 70mm - Power of auger motor 45kW - Closing force 150kN - Plate 450x550 - Closing plate opening from 320 to 620mm Kjdpsvmd Nwefx Ai Rjdr - Head volume 3l

Condition: used, Stretch blow molding machine by Etek Kedjkucxljpfx Ai Rodr ISBM line = Injection stretch blow molding Stretch blow molding machine for single-use PET bottles made from PET preforms Stretch blow molding machine for production using the rotary process Manufacturer: ETEK / GF-Industries, Type Supra 800 sv 1 Serial number: 22000225 Year of manufacture: 2012 Power: 90 kW Mains connection: 400 volts, 50 Hz Weight: approximately 6000 kg In like-new condition

Condition: good (used), Year of construction: 2017, functionality: fully functional, LINEAR PET BLOWING MACHINE SET with auxiliary equipment AC ARCOR - multiBlow2 - 2017 Kdodpfequuvrex Ai Ror Speed: 1,5L - 6000 Cavities: 4 Formats: 0,1 - 3,0L AUXILARY EQUIP 1. Chiller - M.T.A S.p.A - TAE EVO 051 2. LOW Pressure compressor - SHAMAL 45kw 3. Receiver tank - Low pressure - MAX 16Bar 4. Receiver tank - High pressure - MAX 45Bar

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, ID BYP01 We sell a used Chinese - PP melt-blown fabric extrusion line for melt blown, make: Zhangjiagang Sevenstars Machinery Co., Ltd., MFG 2020. It was used for a short time. excellent condition. All EU import duties have been paid. Output max 400 kg per 24 hours. General description: 1. Product size: PP melt blown fabric with width at 600mm (after trimming 17m*3) 2. Main Material: PP compounding material 3. Extruder type: SJ65/33 single screw extruder 4. Output capacity: 350-400kg/24hour 5. Electric power supply: 3phase, 380V; 50Hz 6. Additional equipment: • Vacuum feeder • Raw material dryer • Mesh manual filter • T-mould for melt blown fabric • Static electrical discharge equipment • Belt type forming 850mm • Collecting device • Winder and slitting Model L/D Output Speed of Screw Rotationl Power Center Height SJ-65 10-33 80-150kg/h 20-120r/min 18.5kw 1000mm This line contains the following machines: Automacic vacuum loader ZJ-400 and hopper dryer make RHONG model RDM-25, MFG 2020; Single screw extruder, model SJ65/33, MFG 2020; Heating oven for hot air, model HJGF101-4, MFG 2020; Extrusion T-mold, model: SUS630, made in Japan, MFG 2020; Forming device, MFG 2020; Winder & slitting system, MFG 2020; Oil free air compressor, MFG 2020; The PP melt blown nonwoven production line is a polymer melt extruded from a screw extruder. The polymer is extremely stretched by high-speed hot air or other means to form very fine short fibers, which are aggregated to A web is formed on a roller or a screen curtain, and is finally reinforced by self-adhesion or thermal bonding. Its unique properties are widely used in mask filter materials, thermal insulation filling materials, medical health materials, wiping materials, etc. The finished product can pass the N95 standard as the core material of the mask. Process of melt blown nonwoven production line Polymer preparation --- Melt extrusion --- Metering pump --- Melt blown die head assembly --- Solution thin-flow drawing --- Fibber cooling --- Auxiliary network --- Electrostatic electret --- Reinforced finished product. Melt-blown cloth is produced by melt-blown process. The equipment mainly includes: screw extruder, melt pump, screen changer, melt-blown device, winding device, air system (hot air blower and heater), etc. The function of the screw extruder is to melt the slice material; the role of the melt pump is to accurately measure, control the output and the fineness of the fiber, and continuously and evenly transfer the melt to the spinneret. The function of the screen changer is to filter out impurities in the melt so as not to block the spinneret holes. The function of the winding device is to pack the melt blown cloth into rolls. The function of the air system (hot air blower and heater) is to provide the temperature and pressure of the hot air used in the drawing of the spinning air stream. Kdjdpfx Aieuiq Dhj Rer Price Euro 39.200 Euro + VAT, negotiable, FCA: Oradea / Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 13-13, The BLOMAX 4 Blowmoulding machine is of the model 13-13. The machine has no defects and operates in excellent condition with full functionality. Power : 400V/150A/60000W Kjdpfot Akgwsx Ai Redr Year of construction : 2000

Year of construction: 2012, condition: used, A Sabal backpart moulding machine for shaping shoe counters and heel areas is offered. Hot activation stations: 2, cold pressing stations: 2, quick-change device for pads and lasts, pincer pull device: adjustable with millimetric precision, pincer pull at activation and pressing stations, valve monitoring, mechanical stops at the pressing stations, switchable heated pressing station for processing Lefa counters, flanging function. Weight: approx. 600kg, machine dimensions X/Y/Z: approx. 1760mm/800mm/1750mm. Documentation available. An on-site inspection is possible. Kdsdpfx Aijzvghwe Rsr

Year of construction: 2008, condition: used, A Demag all-electric injection molding machine with Wittmann 3-axis robot and safety enclosure is offered. Clamping force: 1500kN, locking force: 1650kN, max. mold opening stroke: 495mm, min./max. mold height: 275mm/585mm, max. distance between mold platens: 1080mm, mold platens X/Y: 770mm/770mm, clear distance between tie bars X/Y: 520mm/520mm, max. mold weight: 1700kg, max. mold weight on the movable mold platen: 1150kg, ejector stroke: 125mm, ejector force: 35kN, ejector retraction force: 35kN, screw diameter: 35mm, L/D ratio: 20, max. injection pressure: 2430bar, stroke volume: 166cm³, shot weight: 146g, max. metering stroke: 173mm, max. nozzle stroke: 400mm, nozzle immersion depth: 20mm, nozzle contact force: 30kN, installed barrel heating capacity: 9.4kW, material hopper capacity: 35l, control: CDIAS, operating hours: approx. 76000h, machine weight: approx. 7400kg. Including WITTMANN 3-axis robot, year of manufacture: 2006, travel X/Y/Z: 550mm/1200mm/2000mm, robot weight: approx. 240kg as well as safety enclosure and 1 × core pull preparation AS. Documentation available. An on-site inspection is possible. Kjdozvginopfx Ai Rodr

Condition: used, Year of construction: 1998, A Klöckner DESMA rubber injection molding machine with increased clamping pressure is offered. Material processing: rubber, clamping force: 4500kN, min./max. mold height: 180mm/530mm, adjustable opening stroke: 570mm, clear distance between tie bars X/Y: 600mm/810mm, max. clamping area X/Y: 670mm/940mm, heating platen size X/Y: 670mm/940mm, injection: from above, max. injection volume: 3300cm³, injection force: 1886kN, max. injection pressure: 2150bar, screw diameter: 55mm, injection plunger diameter: 105mm, operating pressure: 250bar, number of control zones: 12, heating capacity per control zone: 21kW, ejector: hydraulic top and bottom, ejector slot spacing: 730mm. The machine is currently not operational because the control cabinet of the DRC 2000 (Simatic S7) is already being used elsewhere and is not part of the machine. Documentation available. Inspection possible by arrangement. Kdsdozuz Agepfx Ai Ror

Condition: ready for operation (used), Year of construction: 2005, operating hours: 76,988 h, clamping force: 800 kN, screw diameter: 30 mm, total length: 4,050 mm, total width: 1,930 mm, total height: 2,200 mm, overall weight: 5,200 kg, warehouse no.: 503561 manufacturer: ENGEL type: VICTORY 200-80 Tech controller: CC100 year of construction: 2005 operation hours: 76988 h clamping force: 800 kN size of mould plates h x v: 670 x 600 mm min. mould height: 250 mm max. open daylight: 700 mm opening stroke: 450 mm screw diameter: 30 mm swept volume: 99 ccm injection pressure: 1450 bar equipment included screen text german CEE-socket 16A core pulling hydraulically 1x machine incl. belt conveyor machine incl. Handling machine incl. water flow regulator machine without material hopper Anti vibration mounts Schuko-socket 10A measures of machine l x w x h: 4.05m x 1.93m x 2.2m total weight: 5200KG technical data robot-system Kdjdpfx Aiszt Sdfj Rjr handling type: Linearhandling manufacture: Engel controller: ER-HLI 31 VC year of construction: 2005 handling weight: 2 kg screen-text: deutsch total weight: 250 kg

Year of construction: 2006, condition: used, Clamping force: 500kN, tie-bar spacing: 320x320mm, cylinder diameter: D30, control: Arburg SLOGICA, automatic operating hours: 63.147h, pump operating hours: 65.755h, semi-automatic operating hours: 14h, cycles: 13.943.435. An on-site inspection is possible. Kedpfx Aijzun Uve Rsdr

Year of construction: 2003, condition: used, Clamping force: 300kN, tie-bar spacing: 270x270mm, cylinder diameter: D15, control: Arburg Control+, automatic operating hours: 63.212h, pump operating hours: 63.212h, cycles: 15.328.195. An on-site inspection is possible. Kdjdpfx Aiezun Upo Rer

Year of construction: 2002, condition: ready for operation (used), Clamping force: 2500kN, clear tie bar distance: 630mm/630mm, opening stroke: 1150mm, min. mold installation height: 330mm, screw diameter: 60mm, specific injection pressure: 2000bar, max. stroke volume: 670cm³, connected load: 74kW, control: MC4. Machine dimensions: 5700mm/2200mm/2300mm, machine weight: 12.5t, operating hours: 47,572h. Available from February 2025, including special accessories, Krauss Maffei LRX-S 100, 8x hot runner control points, 4x core pull, blow-out unit, pressure accumulator, hydraulic tie-bar pulling device, energy-saving circuit, ALS interface, 20mA interface and color dosing device interface. On-site inspection is possible, documentation available. Kdedpfx Ajuiykdoi Rer

Year of construction: 2007, condition: ready for operation (used), Various injection molding machines are available. 1) Arburg Allrounder 420 A 1000-400, clamping force: 100t, screw diameter: 30/35mm, year of manufacture: 2005. 2) Demag 1000-420-310 EL-Exis S, clamping force: 100t, screw diameter: 30mm, year of manufacture: 2003. 3) Demag 1000-420-200 EL-Exis S, clamping force: 100t, screw diameter: 25mm, year of manufacture: 2003. 4) Arburg 570 C 2000-150/60 2K, clamping force: 200t, screw diameter: 25/12+15mm, year of manufacture: 2007. 5) Arburg 420 C 1000-250, clamping force: 100t, screw diameter: 35mm, year of manufacture: 1996. 6) Arburg 420 C 1000-250, clamping force: 100t, screw diameter: 30/25mm, year of manufacture: 1995. 7) Arburg 420 C 1000-250, clamping force: 100t, screw diameter: 30mm, year of manufacture: 1994. 8) Netstal Synergy 600-110, clamping force: 60t, screw diameter: 25mm, year of manufacture: 2001. 9) Arburg 900T 800-150, clamping force: 80t, screw diameter: 25mm, year of manufacture: 2001. 10) 2 KM SilcoStar 922A, year of manufacture: 2007. On-site inspection is possible. Individual sale possible. Some machines are partially dismantled and/or defective. Ksdewkiicopfx Ai Rsdr

Year of construction: 2010, condition: ready for operation (used), A vertical injection molding machine Arburg with a horizontal injection unit is available. Clamping force: 800kN, opening stroke: 500mm, min. mold installation height: 250mm, platen distance: 750mm, platen dimensions X/Y: 570mm/570mm, max. mold weight: 600kg. Machine dimensions X/Y/Z: approx. 4300mm/1700mm/2100mm, weight: approx. 3500kg, operating hours: 44117h. Documentation available. On-site inspection is possible. Kjdpfeyddy Uox Ai Rjdr

Year of construction: 2004, condition: ready for operation (used), A large-format horizontal injection molding machine Battenfeld is available. Operating pressure: 210bar, clamping force: 4500kN, screw diameter: 85mm, injection volume: 2128cm³, injection pressure: 1624bar, tie-bar spacing: 900mm/800mm, opening stroke: 950mm, max. mold installation height: 970mm, oil volume: 900l, connected load: 55kW, weight: approx. 20400kg. Documentation available. An on-site inspection is possible. The machine has a defect. Kdsdpfx Aieyz Anme Rer

Year of construction: 2003, condition: ready for operation (used), Six Arburg injection molding machines are available. 1) Arburg 320C 600-250, year of manufacture: 2001, operating hours: 83365h, clamping force: 600kN, screw diameter: 30mm, shot weight: 97g, max. injection pressure: 2470bar, shot volume: 106cm³, centering: 125mm/125mm, max. opening stroke: 550mm, platen spacing: 550mm, platen dimensions X/Y: 446mm/446mm, tie bar spacing: 320mm/320mm, core pulls: 2, temperature control units: 6, machine dimensions X/Y: approx. 4000mm/2300mm. Including Multilift handling unit. 2) Arburg 420C 1000-250, year of manufacture: 2001, operating hours: 90769h, clamping force: 1000kN, screw diameter: 30mm, shot weight: 97g, max. injection pressure: 2470bar, shot volume: 106cm³, centering: 125mm/125mm, max. opening stroke: 750mm, platen spacing: 750mm, platen dimensions X/Y: 570mm/570mm, tie bar spacing: 420mm/420mm, core pulls: 2, machine dimensions X/Y: approx. 4700mm/2350mm. Including Multilift handling unit. 4) Arburg 320C 300-100, year of manufacture: 2000, operating hours: 78784h, clamping force: 300kN, screw diameter: 20mm, shot weight: 28g, max. injection pressure: 2500bar, shot volume: 31cm³, centering: 125mm/110mm, max. opening stroke: 350mm, platen spacing: 350mm, platen dimensions X/Y: 446mm/446mm, tie bar spacing: 320mm/320mm, core pulls: 1, temperature control units: 6. 5) Arburg 220C 250-60, year of manufacture: 2001, operating hours: 86595h, clamping force: 250kN, screw diameter: 22mm, shot weight: 27g, max. injection pressure: 2340bar, shot volume: 30cm³, centering: 110mm/110mm, max. opening stroke: 425mm, platen spacing: 425mm, platen dimensions X/Y: 400mm/400mm, tie bar spacing: 221mm/221mm, core pulls: 1, temperature control units: 6. 6) Arburg 270C 300-100, year of manufacture: 2007, operating hours: 59885h, clamping force: 300kN, screw diameter: 20mm, shot weight: 28g, max. injection pressure: 2500bar, shot volume: 31cm³, centering: 110mm/110mm, max. opening stroke: 550mm, platen spacing: 550mm, platen dimensions X/Y: 446mm/446mm, tie bar spacing: 270mm/270mm, core pulls: 2, temperature control units: 6, machine dimensions X/Y: approx. 3750mm/2400mm. Including Multilift handling unit. 7) Arburg 220S 250-60, year of manufacture: 2001, operating hours: 57504h, clamping force: 250kN, screw diameter: 18mm/22mm, shot weight: 18g/27g, max. injection pressure: 2500bar/2340bar, shot volume: 20cm³/30cm³, centering: 110mm/110mm, max. opening stroke: 425mm, platen spacing: 425mm, platen dimensions X/Y: 400mm/400mm, tie bar spacing: 221mm/221mm, core pulls: 1, temperature control units: 6, machine dimensions X/Y: approx. 3300mm/1100mm. Documentation available. An on-site inspection is possible. Kdodpfx Aetyyn Hsi Rer

Year of construction: 2012, condition: ready for operation (used), Installation height min./max.: 200mm/595mm, opening stroke: 200mm, closing force: 600kN, screw diameter: 25mm, distance between tie bars: 370mm, max. injection volume: 49cm³, operating hours: 55682h. Documentation available. On-site inspection is possible. Kdodpfx Aist E Tq Rj Ror

Year of construction: 2021, condition: ready for operation (used), An almost like-new injection moulding machine Arburg is available. Clamping force: 1600kN, tie bar distance: 520mm, clamping stroke: 364mm, ejector stroke: 150mm, ejector force: 40kN, injection unit: 400, injection pressure: 2500bar. Machine dimensions X/Y/Z: approx. 6000mm/1800mm/2200mm, weight: approx. 6000kg, control: Selogica, operating hours: approx. 67h. Includes enclosure with clean air supply FilterFanUnit and removal robot. Documentation available. An on-site inspection is possible. Kdodpow Rqwtefx Ai Rjr

Year of construction: 2003, condition: ready for operation (used), Clamping force: 1300kN, screw diameter: 40mm, max. injection pressure: 2120bar, shot volume: 182m³, shot weight: 153g, tie bar spacing: 470mm/470mm, platen dimensions X/Y: 650mm/650mm, min. mold installation height: 275mm, max. opening stroke: 850mm, centering: 125mm. Machine dimensions X/Y/Z: approx. 4600mm/1600mm/2200mm, weight: approx. 5500kg. The clamping unit shows an oil leakage at the clamping cylinder. Documentation available. An on site inspection is possible. Kodoygw Siopfx Ai Rjdr

Condition: ready for operation (used), Year of construction: 1993, Some older plastic injection molding machines from Arburg, Demag and Stübbe are available. 1) Stübbe S110/345, year of manufacture: 1976, clamping force: 1000kN, shot weight: 140g, mold installation height min./max.: 180mm/480mm, opening stroke: 320mm, tie bar spacing: 360mm/355mm, screw diameter: 40mm, core pulls: 1. 2) Demag D 150-452 NC III, year of manufacture: 1990, clamping force: 1500kN, shot weight: 207g, mold installation height min./max.: 320mm/550mm, opening stroke: 430mm, tie bar spacing: 460mm/460mm, screw diameter: 45mm, core pulls: 1. 3) Demag D 100-275 NC II P, year of manufacture: 1989, clamping force: 1000kN, shot weight: 130g, mold installation height min./max.: 200mm/400mm, opening stroke: 350mm, tie bar spacing: 400mm/400mm, screw diameter: 38mm, core pulls: 1. 4) Arburg Allrounder 270M 250-75, year of manufacture: 1990, clamping force: 250kN, shot weight: 25g, mold installation height min./max.: 225mm/not specified, opening stroke: 325mm, tie bar spacing: 270mm/270mm, screw diameter: 20mm, core pulls: 1. 5) Arburg 320 850-210, year of manufacture: 1986, clamping force: 850kN, shot weight: 108g, mold installation height min./max.: 250mm/625mm, opening stroke: 375mm, tie bar spacing: 320mm/320mm, screw diameter: 35mm, core pulls: 0. On-site inspection is possible. Individual sale possible. Kedpfox Hz Sbex Ai Rsdr

Year of construction: 2009, condition: ready for operation (used), Clamping force: 2000kN, locking force: 2200kN, max. opening stroke: 570mm, min. mould installation height: 310mm, max. mould installation height: 660mm, max. distance between mould platens: 1230mm, mould platen dimensions: 830x830mm, distance between tie bars: 560x560mm, max. mould weight: 3.3t, max. weight on moving mould platen: 1.7t, max. weight on fixed mould platen: 2.5t, ejector stroke: 180mm, ejector force: 69kN, ejector return force: 31kN, screw diameter: 45mm, L/D ratio: 20, injection pressure at 400°C: 2402bar, shot volume: 358cm³, shot weight (PS): 330g, max. metering stroke: 225mm, max. nozzle stroke: 400mm, nozzle immersion depth (SVO): 20mm, nozzle contact force: 80kN, installed barrel heating capacity: 13kW, material hopper capacity: 70l, oil tank capacity: 500l, screw drive: 32kW, clamping unit drive: 32kW, pump unit power: 15kW, total installed power: 92kW, continuous sound pressure level: 74dB(A), length: 5700mm, width: 1700mm, height: 2200mm, weight: 11t, operating hours according to PLC: 36,734h, barrel heating: 25,665h, pump: 18,222h, documentation available. An on-site inspection is possible. A Wittmann robotic cell is also optionally available. Kdodpey Tx Rbjfx Ai Rjr

Year of construction: 2002, condition: ready for operation (used), Clamping force: 1600kN, tie bar spacing: 570x520mm, platen dimensions: 810x805mm, max. mould diameter: 804mm, rotary table diameter: 735mm, min. installation height: 300mm, opening stroke: 650mm, opening force: 84kN, tie bar diameter: 80mm, max. daylight opening: 950mm, ejector force: 41.2kN, ejector stroke: 200mm, oil tank volume: 400l, standard drive power: 37kW, hydraulic operating pressure: 240bar, control system: Battenfeld Unilog B4, weight: 7.8t. An on-site inspection is possible. Kdjdpoy T Sdzefx Ai Ror

Year of construction: 2005, condition: ready for operation (used), A total of four Engel injection molding machines are available. 1) Engel ES 80/25 HL-V, year of manufacture: 1999, the machine is a defective spare parts carrier. 2) Engel ES 80/25 HL-V, year of manufacture: 2001. 3) Engel VC 200/45 Tech, year of manufacture: 2004. 4) Engel e-Motion 200/55, year of manufacture: 2005. Documentation available. On-site inspection is possible. Individual sale possible. Kdsdpfx Aisv Extzj Rsr

Year of construction: 2005, condition: ready for operation (used), There are two BOY 55M available, both year of construction 2005. Clamping force: 550kN, screw diameter: 38mm, stroke volume: 196cm³, injection pressure: 2000bar, platen dimensions: 565mm/540mm, tie bar distance: 360mm/335mm. Workpiece height min./max.: 250mm/650mm, opening stroke: 400mm, max. platen distance: 1050mm, ejector stroke: 80mm, max. mold weight: 600kg. Dimensions X/Y/Z: approx. 3300mm/1200mm/2100mm, weight: approx. 2300kg, operating hours: 29664h, control: Procan MD. Robot interface Euromap 12 included. Kdedpfx Aiotyaypj Rer