Used Asea Contactor for sale (237)

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. Itsdpfx Aowzl Hxoayok * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: used, Single-column eccentric press HELMERDING Type EH 25 B Machine No. 5917 Year of manufacture: 1993 Pressing force: 25 tons Throat depth: 180 mm Table area: 560 x 360 mm Ram area: 315 x 150 mm Table through-hole: 150 x 100 mm Stroke adjustment: 8 - 82 mm Ram adjustment travel: 60 mm Installation height max.: 330 mm Clamping pin bore: Ø 40 mm Strokes per minute: 145 Table height adjustment: 150 mm Table height above floor: 630 - 780 mm Motor power: 1.5 kW Power supply: 400 Volt, 50 Hz - Hydraulic clutch-brake combination, manufacturer: ORTLINGHAUS - Electric foot switch and two-hand control - Automatic central lubrication by BEKA lubrication system - Electrical cabinet with 2-channel contactor control - Press table height-adjustable via 2 threaded spindles - UVV [accident prevention regulations] according to VBG 7n 5.1 for manual loading operations - Electrical diagram Space requirements (L x W x H): 1600 x 1100 x 1900 mm Isdpfoyath Tox Aayjtk Weight: 2 tons Good condition

Condition: good (used), Contactor, semiconductor contactor, contactor, power contactor, capacitor contactor -Manufacturer: Moeller, Schütz power contactor -Type: DIL2AM-G -Number: 2x contactors available -Price: per piece -Dimensions: 105/70/H165 mm Itsdpfx Aokia S Teaysk -Weight: 1.8 kg/piece

Condition: ready for operation (used), Year of construction: 2021, pressing force: 275 t, total width: 2,000 mm, total height: 3,000 mm, overall weight: 13,000 kg, product length (max.): 4,000 mm, Press brake manufactured in 2021. This KNUTH AHK H 30270 features a pressing force of 270 t and a bending length of 3,100 mm. It includes a Cyberlec Touch 8 Controller and a motorized CNC anti-winding system for enhanced precision. The machine is equipped with front support arms sliding on linear guides and a pedal drive for ease of operation. If you are looking to get high-quality bending capabilities, consider the KNUTH AHK H 30270 press brake we have for sale. Contact us for further details. • Loading assistance: Yes • Running hours: 372,4 hours / 36.888 bends • 3 controlled axes: Y1, Y2, X Itjdpszfphfefx Aaysk • Controller: Cyberlec Touch 8 • Motorized CNC anti-winding (crowning) system • European clamping tool system • Front support arms sliding on linear guides along the entire length; equipped with T-channels and tilt stops • Rear pusher (backgauge) actuated by servomotor with movement via ball screws and linear guides (X) • Protective guards with electrical contactors • Pedal drive • Workspace lighting lamp • CE certification with Akas Laser Manual safety LC II M FMSC • Technical and operating manual • Distance between columns: 2.600 mm • Knife range: 265 mm • Distance between table and upper support: 485 mm • Depth in the console (C): 410 mm • Table height: 950 mm • Y-axis speeds: fast 110 mm/s; bending 9 mm/s; return 100 mm/s • X-axis fast speed: 250 mm/s; X-axis range: 750 mm/s • R-axis fast speed: 100 mm/s; R-axis range: 200 mm/s • Engine power: 22 kW • Oil tank: 350 L Additional equipment • Tooling: Punch height 67 mm; 4V prism 6 x 60 mm Technical Specification Bending Length 3100 mm

Year of construction: 2019, condition: new, functionality: fully functional, Root reducer – new (in storage) consisting of: 1. Tapered roller conveyor Plant data: Wood lengths: 2 m to 4.6 m (main length: 2.7 m), extendable to 8 m (optional, at an extra charge) Log diameter: 200 mm to 1,100 mm Wood types: Softwood or hardwood, max. individual log weight 2 tons Piece rate: up to 5 pieces/minute, of which with root reduction: up to 2 pieces Operation: 1-shift operation Dimensions: Length: approx. 5 m Roller width: 800 mm Description: Tapered roller conveyor for roundwood with housing bearing (nominal diameter: 60 mm); Outer diameter of the tapered rollers: 450 mm; drive chain: roller chain 5/4"; integrated 4-arm, hydraulic lifting device for transferring to the root reducer, steel housing plain bearing; drive of the tapered roller conveyor via gear motor with reduction gearbox and soft start; integrated light barriers (2 pieces) for log positioning 2. Root reducer Dimensions: Length: approx. 7 m Description: - 3 driven chain beds, drive chain: roller chain 6/4" with square tooth attachment Isdpfxjzcaqts Aayetk - Drive via gear motor - 2 support blocks with non-driven rollers (roller bearing) - hydraulically pivoting clamping device for clamping from above with V-bed - Drive chain: roller chain 6/4", drive via gear motor; - housing-mounted milling shaft with reversible, interchangeable knife blocks (4 cutting edges per knife block), drive via three-phase motor (drive power: 75 kW; flexible tire coupling) - Star-delta operation for the drive motor (energy-saving mode for idle operation - automatic switchover during the reduction process) - Milling shaft length: 1,200 mm, mounted on a rotatably supported, adjustable drive rocker (hydraulic drive) - 4-arm lifting device, hydraulically driven - integrated hydraulic unit (15 kW) - integrated log diameter measurement for automatic milling time calculation (control unit included in item 2), for wood lengths under 3.5 m, the support position of the log must be adjusted (reduced reduction length) Reduction length for log length of 2.7 m: 0.7 m, for log length of 3 m: 0.9 m 3. Control system - Control cabinets in grounded design, equipped with control units for all drives of items 1 and 2, - Power supply: 3x400 VAC; Rittal control cabinet; motor contactors and contactors from Siemens - Freely programmable controller Bernegger & Rainer - Control cabinets completely wired and tested - Reserve slots for approx. 5 drives - Circuit diagram for the system - Signal exchange via potential-free contacts - Emergency stop system; including necessary sensors; manual operation option Control function description: - Automatic reduction operation, for log lengths under 3.5 m, an adjustment of the support position (wood alignment) is required (reduced reduction length) - Automatic log positioning via the tapered roller conveyor, the reduction process must be activated manually (reduction command) Price: ex works

Condition: new, Year of construction: 2025, total height: 4,000 mm, total length: 7,000 mm, total width: 3,000 mm, warranty duration: 24 months, temperature: 80 °C, air demand: 36,000 m³/h, input voltage: 380 V, heating capacity: 345 kW (469.07 HP), power: 40 kW (54.38 HP), fuel: liquid petroleum gas (LPG), energy consumption: 40 kWh, insulation material: Mineralwolle, insulation thickness: 50 mm, nominal power: 345 kW (469.07 HP), Equipment: lighting, MAIN STANDARD Our paint booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. Booth processes are managed via a PLC system, ensuring that desired values are maintained consistently. OPERATING PRINCIPLES OF THE BOOTH The booth’s processes are managed through a control panel, which oversees the following steps: PAINTING PROCESS During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (paint stop filters) collect paint particles, and the air passes through final exhaust filters before being discharged. Itsdpfx Aajwzmcboyek FLASH-OFF PROCESS After painting, the booth continues operating for approximately 15 minutes to purge residual solvents and thinners. During this phase, fresh air circulates from outside into the booth. DRYING PROCESS In this stage, 80% of the air passing through the booth is heated to 60°C and introduced via a distribution system. Since 20% of the solvent is released during drying, it is expelled with the exhaust air. Industrial coatings are typically dried at 60°C, but the booth temperature can be adjusted as needed via the control panel. COOLING PROCESS After the 30-minute drying cycle, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the subsequent 5-minute cooling phase, fresh air from outside circulates through the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels govern the functions and operation of machines and devices housed within the booth. The panel is made of durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical Equipment and Control Panel: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to accommodate booth relocation if needed. • Operating equipment uses 380 V 50 Hz, while control devices operate at 220 V. • The booth’s operation time can be monitored on the electronic control panel, enabling straightforward maintenance scheduling. • Temperature and time settings for booth ventilation (solvent flash-off), intermediate drying, and final drying can be easily adjusted to required values on the digital display of the electronic control panel. • Users can monitor and adjust the drying time using the heating thermostat and time relay.

Condition: good (used), Included in this package: 11 x stands a 700cm x 110cm (gray) 60 x crossbars a 3600mm (gray) 120 x safety pins Itodpfx Aorhkvnjayek Results in a rack row with 10 bays each with 3 levels of floor space = a total of 160 pallet spaces (800kg per pallet) Manufacturer: Bito Type: P4 Condition: used, good condition Height: 700 cm Length: approx. 1 x 37.10m Shelf depth: 110 cm Bracing: screwed Truss length: 3.60 m Shelf load: 3200 kg Bay load: 9600 kg Pallet spaces: 96 Accessories such as Floor fastening connectors Load warnings collision contactors Guard rails gratings Rear wall grating Depth bars Guard rails and much more... Just ask us!

Condition: excellent (used), MyRef MY-ZB26-TFD refrigeration unit MyRef MY-ZB26-TFD condensing unit suitable for refrigeration applications Typical applications are Freezer cabinets in supermarkets and minimarkets cold stores Beer cellars Iodpfxjvtl T De Aayotk Milk cooling systems Standard equipment Copeland Scroll M compressor ZB series with sound insulation hood Oil sump heater Liquid receiver with burst protection Filter dryer Sight glass visible from outside Ball shut-off valves Component-tested combined HP/ND safety pressure switch Electrical equipment: IP 55 switch box, compressor contactor, DIN rail mounting Condenser is integrated and protected in the housing Condenser fins coated with epoxy resin phenol (gold paint*) High-quality housing: solid in 1.5 mm galvanized and powder-coated sheet steel, base plate and feet in 2 mm sheet steel Frame construction with individually removable panels; all screws and components can be accessed from the front with minimal effort Blind rivet nuts with carriage bolts for secure, durable fastening without rust problems Pressure-controlled speed regulator with EMC filter Space-saving installation of several units next to each other possible; required mounting distance 25 mm Type: MyRef -ZB26-TFD Copeland Scroll Condensing unit Type: MyRef -ZB26-TFD Built-in compressor type: ZB19-KQE-TFD-525 Sound pressure level: 39 dbA-10 m Collector volume: 6 liters Air volume: 4500m³/h Cooling capacity: 9 kW Voltage: 400V,3PH,50Hz Power consumption: 8.9 A Dimensions: HxWxD 715 x 1120 x 450 mm Weight: 102 kg Financing through our bank is also possible. komplett-konzept.leasingo.de You can find more items - new and used - in our store! International shipping costs on request!

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 Iodpfxswu Tu Ds Aayotk 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: used, Year of construction: 2019, liter capacity 980 l Pressure of pump 8 / 20 bar Isdpfxox Ak Eto Aayetk control Schütze / Contactors weight of the machine ca. 560 kg dimensions of the machine ca. 2,3 x 2,0 x 1,8 m Coolant System MAYFRAN - BFU 980 /S/20+/8 - NEW, unused - universally applicable - can be controlled via contactors - incl. paper band filter - Number of pumps: 2 - Pump capacity: 4.0 kW, 2,917 rpm, 5.8 m³, 96.6 l/min, pressure 25 bar, max. temperature 90°C -.- kW, 2,864 rpm, 2.0 m³/h, 33.3 l/min, pressure 25 bar, max. temperature 90°C

Condition: used, Barrenschütz, DC contactor, contactor, DC switch, power contactor, power switch, high-voltage switch ABB Type NORR63-03 CC-SP FPL7146886R6000 CTC2014028R0001 Contactor Type: Normally open main contacts Design: Open, mounted on a bar Actuator: AC + laminated magnetic circuit + rectifier + shunt resistor Actuator rated voltage: 220-230 V / 50-60 Hz Main contact rated current: 63 A Main contact rated voltage: 1500 VDC Number of main contacts, normally closed: 0 Number of main contacts, normally open: 3 Number of auxiliary contacts: 1 normally open + 1 normally closed + 1 changeover Ijdpfx Aofipfusayotk Auxiliary contact rated current: 6 A - Main contacts with deion chambers for rapid arc quenching Dimensions W x H x D: 410 x 250 x 195 mm Weight: approx. 9 kg Used, but in very good condition.

Condition: new, Year of construction: 2017, SICK S30B-3011BA Safety Laser Scanner Features Design sensor without system connector Indoor application area Protective field range 3 m Warning field range 8 m (at 15 % remission) Distance measuring range 30 m Type of field set Triple field sets Number of field sets 1 Number of fields 3 Number of monitoring cases 1 Scanning angle 270 Resolution (configurable) 30 mm, 40 mm, 50 mm, 70 mm, 150 mm Angle resolution 0.5° Response time 80 ms 1) Protective field allowance 100 mm Number of multiple evaluations 2 ... 16, configurable Delay of automatic reset 2 s ... 60 s, configurable Safety characteristics Type 3 (IEC 61496) Safety integrity level SIL2 (IEC 61508) Category Category 3 (EN ISO 13849) Performance Level PL d (EN ISO 13849) PFHD (mean probability of dangerous failure per hour) 8.0 x 10-8 TM (service life) 20 years (EN ISO 13849) Function Restart interlock ✔ Contactor monitoring (EDM) ✔ Multiple evaluation ✔ Contour as reference ✔ Integrated configuration memory ✔ Measurement data output Measurement data output Via RS-422 Secure SICK device communication via EFI ✔ Connection type Connection type System connector with or without connecting cable Universal I/Os 5 1) Inputs Contactor monitoring (EDM) 1 2) Reset/restart 1 2) Stand-by 1 Outputs OSSD pairs 1 Signal outputs 3 3) Type of configuration PC with CDS (configuration and diagnostics software) Configuration and diagnostics interface RS-232 Transmission rate 38.4 kBaud Data interface RS-422 Transmission rate ≤ 500 kBaud Secure SICK device communication via EFI Transmission rate ≤ 500 kBaud Cable length ≤ 50 m Conductor cross-section 0.22 mm² 1) Freely programmable, e.g. contactor monitoring input, reset input, contamination warning, reset required. 2) Availability depends on configuration of universal I/Os. 3) Freely programmable, e.g. warning field, contamination, reset required. Protection class III (EN 50178) EN 60950 Supply voltage Uv 24 V DC (16.8 V DC ... 30 V DC) Current consumption ≤ 0.33 A 1) ≤ 1,7 A 2) Iedpopudqxefx Aaystk Outputs Safety outputs (OSSDs) 2 x 250 mA Signaling outputs 3 x 100 mA 3) 1) At 24 V DC without output load. 2) At 24 V DC with maximum output load. 3) Freely programmable, e.g. warning field, contamination, reset required. Item condition: new, from stock liquidation (Without original packaging). Year of manufacture 2017 Financing through our bank is also possible. komplett-konzept.leasingo.de More scanners - new and used - you can find in our store! International shipping costs on request!

Condition: new, Year of construction: 2022, SICK S30B-3011BA Safety Laser Scanner Features Design sensor without system connector Indoor application area Protective field range 3 m Warning field range 8 m (at 15 % remission) Distance measuring range 30 m Type of field set Triple field sets Number of field sets 1 Number of fields 3 Number of monitoring cases 1 Scanning angle 270 Resolution (configurable) 30 mm, 40 mm, 50 mm, 70 mm, 150 mm Angle resolution 0.5° Itjdpfxopudtle Aaysk Response time 80 ms 1) Protective field allowance 100 mm Number of multiple evaluations 2 ... 16, configurable Delay of automatic reset 2 s ... 60 s, configurable Safety characteristics Type 3 (IEC 61496) Safety integrity level SIL2 (IEC 61508) Category Category 3 (EN ISO 13849) Performance Level PL d (EN ISO 13849) PFHD (mean probability of dangerous failure per hour) 8.0 x 10-8 TM (service life) 20 years (EN ISO 13849) Function Restart interlock ✔ Contactor monitoring (EDM) ✔ Multiple evaluation ✔ Contour as reference ✔ Integrated configuration memory ✔ Measurement data output Measurement data output Via RS-422 Secure SICK device communication via EFI ✔ Connection type Connection type System connector with or without connecting cable Universal I/Os 5 1) Inputs Contactor monitoring (EDM) 1 2) Reset/restart 1 2) Stand-by 1 Outputs OSSD pairs 1 Signal outputs 3 3) Type of configuration PC with CDS (configuration and diagnostics software) Configuration and diagnostics interface RS-232 Transmission rate 38.4 kBaud Data interface RS-422 Transmission rate ≤ 500 kBaud Secure SICK device communication via EFI Transmission rate ≤ 500 kBaud Cable length ≤ 50 m Conductor cross-section 0.22 mm² 1) Freely programmable, e.g. contactor monitoring input, reset input, contamination warning, reset required. 2) Availability depends on configuration of universal I/Os. 3) Freely programmable, e.g. warning field, contamination, reset required. Protection class III (EN 50178) EN 60950 Supply voltage Uv 24 V DC (16.8 V DC ... 30 V DC) Current consumption ≤ 0.33 A 1) ≤ 1,7 A 2) Outputs Safety outputs (OSSDs) 2 x 250 mA Signaling outputs 3 x 100 mA 3) 1) At 24 V DC without output load. 2) At 24 V DC with maximum output load. 3) Freely programmable, e.g. warning field, contamination, reset required. Item condition: new, from stock clearance (Without original packaging) Year of manufacture 2022 Financing through our bank is also possible. komplett-konzept.leasingo.de More scanners - new and used - you will find in our store! International shipping costs on request!

Condition: used, Year of construction: 2019, liter capacity 980 l Pressure of pump 8 / 20 bar control Schütze / Contactors weight of the machine ca. 560 kg dimensions of the machine ca. 2,3 x 2,0 x 1,8 m Itjdpfjwhzmhox Aayjk Coolant System MAYFRAM - DPF400-V980 SKD (BFU 980 /S/20+/8) - NEW, unused - universally applicable - can be controlled via contactors - incl. paper band filter - Number of pumps: 3 - Pump capacity: 4.0 kW, 2,917 rpm, 5.8 m³/h, 96.6 l/min, pressure 25 bar, max. temp. 90°C 3.0 kW, 3,514 rpm, 20.5 m³/h, 341.66 l/min, pressure 25 bar, max. temp. 90°C -.- kW, 2,864 rpm, 2.0 m³/h, 33.3 l/min, pressure 25 bar, max. temp. 90°C

Condition: used, Year of construction: 2019, liter capacity 980 l Pressure of pump 8 / 20 bar control Schütze / Contactors weight of the machine ca. 650 kg dimensions of the machine ca. 2,3 x 2,0 x 1,8 m Coolant System BOSCH REXROTH - BFA 980-50Hz /S/20/8 - very good condition - universally applicable - can be controlled via contactors Itedpjwhzmnofx Aayjk - incl. paper band filter - Number of pumps: 2 - Pump performance: 1.7 kW, 2.3 HP, 2,890 rpm, 60 l/min 3.0 kW, 4.0 HP, 2,930 rpm, 40 l/min

Condition: used, Year of construction: 2019, liter capacity 600 l Pressure of pump 8 / 20 bar control Schütze / Contactors weight of the machine ca. 450 kg dimensions of the machine ca. 1,2 x 1,8 x 1,6 m Coolant System BMF - BFU 600 /S2/20/8+ - NEW, unused - universally applicable - can be controlled via contactors - incl. paper band filter - Number of pumps: 2 Itedpswhzmzofx Aayok - Pump performance: 2.6 kW, 3.5 HP, 2,880 rpm, 160 l/min 3.0 kW, 4.0 HP, 2,930 rpm, 40 l/min

Condition: used, Year of construction: 2019, liter capacity 980 l Itsdpfswhzm Ujx Aayjk Pressure of pump 8 / 20 bar control Schütze / Contactors weight of the machine ca. 560 kg dimensions of the machine ca. 2,3 x 2,0 x 1,8 m Coolant System MAYFRAN - BFU 980 /S/20+/8 - NEW, unused - universally applicable - can be controlled via contactors - incl. paper band filter - Number of pumps: 2 - Pump capacity: 4.0 kW, 2,917 rpm, 5.8 m³, 96.6 l/min, pressure 25 bar, max. temperature 90°C -.- kW, 2,864 rpm, 2.0 m³/h, 33.3 l/min, pressure 25 bar, max. temperature 90°C

Condition: used, Contactor, semiconductor contactor, contactor, power contactor, capacitor contactor, motor contactor Itsdpfxsh Rf Nhe Aaysk -Manufacturer: Siemens, contactor type 3TF4322-0BB4 -Number: 4x available -Price per piece -Dimension: 85/45/H140 mm -Weight: 0.7 kg/pc.

Condition: used, Contactor, semiconductor contactor, contactor, power contactor, capacitor contactor -Manufacturer: Telemecanique, Contactor Square D -Type: LC1D096 LR3D 086 -Number: 2x contactor available -Price per piece -Dimension: 125/45/H85 mm Ijdpfxjkia T Hs Aayjtk -Weight: 0.5 kg/pcs

Condition: used, Contactor, semiconductor contactor, contactor, power contactor, capacitor contactor, motor contactor -Manufacturer: Siemens, contactor type 3RT1045-1AP04-3MAO with auxiliary switch orig Itjdpfxsiiihfj Aayjk -Auxiliary switch: type 3RH1921-1HA22 -Number: 4x available -Price per piece -Dimensions cardboard: 150/75/H205 mm -Weight: 1.8 kg/pc.

Condition: used, Contactor, semiconductor contactor, contactor, power contactor, capacitor contactor Itedpfokia T Rjx Aaysk -Manufacturer: Telemecanique, Contactor Square D -Type: LC1D096 LR3D 146 -Number: 1x contactor available -Price per piece -Dimension: 125/45/H85 mm -Weight: 0.5 kg/pcs

Condition: good (used), Year of construction: 2001, Contactor, semiconductor contactor, contactor, power contactor, capacitor contactor, motor contactor -Manufacturer: Albright, relay contactor -Type: SW180B-3 -Voltage: 24 V -Number: 9x contactors available -Price: per piece -Dimensions: 122/60/H45 mm -Weight: 0.7 kg/pc. Isdpfxoy Aty Aj Aayjtk

Condition: new, As-new, unused electric chain hoists from Liftket. Load capacity: 250kg. Main lifting speed: 18.0 m/min. Fine lifting speed: approx. 4.50 m/min. Number of strands: 1. Hoist group: 3m/M6. Voltage/Frequency: 400V/50Hz. Control type: contactor control. Control voltage: 24V. Lifting height: 125m. Chain type – finish: 5.2x15/EN 818-7-T. Hook version: hook suspension with rubber sleeve. Number of lifting speeds: 2, with emergency stop. Control cable: 2m. Further details available upon request. Isdey I Upvopfx Aayjtk

Condition: good (used), Contactor, semiconductor contactor, contactor -110 V 60 Hz -SK: 4120116 Itjdpfob A Nztsx Aaysk -Quantity: 14 pieces available -Price: per piece -Weight: 0.5 kg

Condition: new, Year of construction: 2023, Alzmetall Alztronic i16 table drilling machine 5" touch display Condition: new Call us and ask us about special discounts or send us your request by email with your contact information and we will get back to you. 5" or 7" display with scratch-resistant glass surface - Optimal readability for the operator - Simple and uniform operator guidance using pictograms - Manual input of spindle speed - target value - Speed display - actual value - Integrated drilling depth display with touch zero point transfer (drilling start) - Virtual drilling depth scale in the display - Machine status displays and warnings in the display (safety)• Main switch, lockable - Right and left rotation through contactor control - Control voltage 24 V - Service information - Selectable operating language: DE/EN/FR/ES/IT/NL/RU - Spindle braking function - ALZTRONIC only (safety) - Adjustable display timeout Standard Equipment: -AC motor 230 V, 50 Hz -Infinitely variable speed adjustment -Reversing switch for right-left rotation -Spindle protection with electrical protection -On/off button with lockable emergency stop flap -Connection plug, cable length 3m -Paint: structural paint light gray RAL 7035, anthracite RAL 7016, white aluminum RAL 9006 Drilling capacity steel E335 (St 60) 16 mm Thread cutting steel E335 (St 60) M 12 Drill chuck taper MK 2 Spindle stroke 80 mm Thread 190 mm Itjdpfoy S Atksx Aaysk Column diameter 65 mm Manual feed Drill head height adjustment by handwheel Net weight approx. 83 kg Infinitely variable speed adjustment Motor 0.54 kW Spindle speed rpm 100-2000 Optional: - Röhm Supra drill chuck 1-13mm or 3-16mm - Alzmetall under-table For self-collection. Forklift available. Shipping also possible. Errors, changes and prior sale reserved. Other Alzmetall table drilling machines and pillar drilling machines always in stock!