Used Weiler Primus Vcd for sale (163)

Condition: used, Year of construction: 1984, turning length 0500 mm greates pass round over bed 250 mm swing diameter over slide rest 160 mm spindle bore 24 mm MK 2 turning speeds 60- 3000 U/min Cb88Kt98Ke dimensions 1200 x 600 x 1250 mm weight 550 kg

Condition: excellent (used), Weiler Primus Lead & Pull Spindle Table Lathe Super Condition !!!! Technical data: >> Year of construction ca.1988 Machine-No.3448 >> center height 120 mm >> center distance 430 mm >> speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm >> short taper spindle head DIN 55027 >> tailstock MK 2 >> feeds from 0,03 to 0,15 mm /U >> Possible threads metric , inch , module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck 125mm NEW with 2 sets of jaws. >> collet chuck equipment NEW from with collets NEW from 2mm to 25mm 1 mm rising >> Mulifix size A with 2 pcs steel holders >> Change gears >> Fixed steady rest >> Faceplate >> Spindle cover >> Base cabinet Cgt2K8Xg0A To the machine : Offered is a Weiler Primus leading and traction spindle table lathe with base cabinet in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. Even at high speeds the Weiler runs smoothly. The Primus is from a state owned company where it was little used. This newer generation of Weiler lathes is very operator friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and convince yourself of the condition. Against surcharge digital display

Condition: good (used), Year of construction: 1980, 1 x L+Z lathe Weiler Primus Bofj9Vnddit Year of manufacture approx. 1980 Very nice machine from medical technology company. Technical data: Center height: 120 mm Center width: 450 mm Spindle bore: 23 mm Speeds: 60 - 3,000 rpm Feed rates: longitudinal 0.05 - 0.6 mm/rev. Tailstock: Mounting: MK 2 Accessories: Quick clamping device 40 x collet chuck 1 - 20 mm 0.5 mm increasing 1 x 3 - jaw chuck 125 mm knocker 1 x Multifix A quick-change holder with 2 interchangeable cassettes 1 x fixed counter point 1 x drill chuck 1 - 13 mm Hand tool The machine can be inspected under power.

Condition: excellent (used), Parallel Lathe WEILER type PRIMUS Between points: 400 mm Maxi Ø on bench: 250 mm Maxi Ø over saddle: 130 mm Spindle Ø 24 mm Turret Multifix type A 3-jaws chuck Ø 155 mm Threadings Metric + Whitworth P2W8Yikt Tailstock CM2 Scale HEIDENHAIN ND522 Feeds: auto 2 axes New electrical panel Delivered with 1 4-jaws chuck Ø 155 mm 4 tool holders, 1 drill chuck Voltage: 380 V Dimensions (L x W x H): 1300 x 900 x 1900 mm Weight: approx 500 kg Machine in VERY GOOD CONDITION

Year of construction: 1986, Condition: used, Weiler Primus lathe built approx. 1986, three-jaw chuck, Multifix. Machine in good condition, ready for demonstration under power on request. Bkk9Tvmuxsk

Condition: excellent (used), Functionality: fully functional, D537 Weiler Primus lead and feed spindle lathe with 3 axis digital readout Fagor from training workshop !!! Technical data: >> year of construction approx. 1985 machine no. 2872 >> Center height 120 mm >> Center width 430 mm Bnqspfqaf3 >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 3-axis digital readout from Fagor >> 1 new three-jaw chuck 125mm with 2 sets of jaws >> Collet chuck device with collets from 1mm to 20mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Interchangeable wheels >> Electronic spindle protection >> Rear panel To the machine : We are offering a Weiler Primus lead and feed spindle lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Year of construction: 1986, Condition: used, Weiler Primus lathe year ca.1986, three-jaw chuck , Multifix. Machine in a good condition , By arrangement under power ready for demonstration. Gonvcxqt2X

Condition: excellent (used), Machine/vehicle number: 2611, Weiler Primus leading & traction spindle lathe with 3 axis digital display Fagor from training workshop !!!! Technical data: >> Year of construction ca.1985 Machine-No.2611 >> center height 120 mm >> center distance 430 mm >> speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm >> short taper spindle head KK4 DIN 55027 >> tailstock MK 2 >> feeds from 0,03 to 0,15 mm /U >> Possible threads metric , inch , module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 Kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 3 axis digital display from Fagor >> 1 piece three-jaw chuck 125mm with 1 set of jaws >> Collet device with collets from 1mm to 20mm 1 mm increasing Bgcerbxqb8J >> Mulifix size A with 3 pcs steel holders >> Change gears >> Electronic spindle protection >> Back wall To the machine : Offered is a Weiler Primus leading and traction spindle lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. Even at high speeds the Weiler runs smoothly. The Primus was in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and convince yourself of its condition.

Condition: excellent (used), Functionality: fully functional, D522 Weiler Primus lead and feed spindle lathe with 3 axis digital readout Fagor from training workshop !!! Technical data: >> Year of construction ca.1985 Machine-No.2463 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 Boawjmwo >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 3-axis digital readout from Fagor >> 1 three-jaw chuck new 125mm with 2 sets of jaws >> Collet chuck device with collets from 1mm to 20mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Interchangeable wheels >> Electronic spindle protection >> Rear panel To the machine : We are offering a Weiler Primus lead and pull spindle lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Year of construction: 1990, Condition: used, L + Z Lathe WEILER Type LZ PRIMUS GS Machine no. No. 2461 Year of construction approx. 1990 Center width 400 mm Turning diameter over bed 250 mm Center height above bed 125 mm Turning diameter over support 140 mm Center height above support 70 mm Spindle bore 24 mm Spindle speed 60 - 3000 rpm 18 steps Feed lengthwise and flat Chuck flange short taper DIN 55022 size 4 Inner tailstock taper MK 2 Drive power 1.1 kW and 1.5 kW pole-changing Mains connection 380 Volt, 50 Hz - 3-axis digital readout FAGOR, type 30i-T-B - Spindle speed via 2 motor speeds and 9 gear stages - 3-jaw lathe chuck RÖHM Ø 125 mm with stepped jaws - MULTIFIX quick-change tool holder with 1 interchangeable cassette - Set of collets Ø 1 / 3 / 4 / 5 / 7 / 8 / 10 / 14 / 15 / 16 / 17 / 19 / 20 / mm - 1 centering tip for collet chuck holder - Emergency stop - Hinged chuck guard - Splash guard P9If7Xaps - Machine light - electrical diagram - Machine mounted on a steel plate (steel plate L x W x H 1200 x 500 x 30 mm, 140 kg) Space requirement L x W x H 1200 x 900 x 1560 mm Weight 520 kg good condition

Condition: used, Turning length: 500 mm, Spindle bore: 51 mm, Rotational speed (max.): 5,000 rpm, Turning diameter over bed slide: 420 mm, Center height: 245 mm, Equipment: Documentation/Manual, For sale here is a CNC lathe from Weiler in used condition! See pictures Machine will be sold free loading! Make: Weiler Model: Primus 2 CNC Turning diameter over bed: approx. 420 mm Turning diameter over support: approx. 220 mm Max. Speed: approx. 5,000 rpm Motor power: approx. 19 kW Centre height: approx. 245 mm Centre width: approx. 500 mm Jaw chuck Ø: approx. 200 mm Spindle bore: approx. 51 mm We are at your disposal for any questions! Sale ex location 42855 Remscheid, free loading! Cxxkcztbpk Can be loaded with a forklift. You will receive an invoice with VAT shown. Inspection / collection is possible by arrangement in 42855 Remscheid. Errors in technical data and prior sale reserved.

Condition: like new (used), Functionality: fully functional, 3-axis digital display Electrically secured chuck guard Electric spindle brake Covered lead and pull spindle Center height 140 x 500 mm spindle bore 40 mm Infinitely variable speed control rpm 30 - 4,000 1 Multifix cassette holder with cassettes 1 Weiler 3-jaw chuck 160 mm 1 machine light 1 chip back panel 1 coolant pump 1 drill chuck 1 rolling center punch 1 additional tailstock with manual high-speed drill sleeve 1 draw tube for collets 1 collet holder 1 complete set of collets 1 set of machine feet The machine, the guides and the gears, as well as the play of the spindles, are mechanically in mint condition. We have overhauled the machine and changed all the oils. Dpoebz The condition of the machine is completely unused. It comes from a training center and was only used occasionally. It is ideally suited as a replacement for a new machine.

Condition: used, Year of construction: 1978, turning diameter over bed 250 mm turning diameter over slide rest 180 mm turning length 450 mm total power requirement 1,5 kW weight of the machine ca. 0,55 t dimensions of the machine ca. 1,2 x 0,8 x 1,5 m No. 3629 Lead and feed spindle lathe WEILER Primus LZG Working range: Center height 125 x 400/500 Drive: 1.5 kW Three-jaw chuck Ø 130 mm Various collets Driving disk Multifix A steel holder head and 2 holders Cjfi0Gtuti documentation Spindle bore 24 mm Ø Tailstock taper MK 2 Speed range: 60 - 3000 min-1 Dimensions: approx. 1.20 x 0.80 x 1.50 m Weight approx. 550 kg

Condition: ready for operation (used), Year of construction: 1999, Main Drive Number of spindles 1 Spindle speed range 30 - 4000 rpm Cjgpadilqc Workpiece Workpiece drm over bed 280 mm Workpiece drm over support 152 mm This Weiler Primus VC lathe was manufactured in 1999. It features a rotation diameter over bed of 280 mm and over cross slide of 152 mm. The turning length between centers is 500 mm, with a speed range of 30 - 4000 rpm. It can handle workpieces up to 100 kg. A great opportunity to buy this Weiler Primus VC lathe. Contact us for further details regarding this lathe. Application Types Turning

Condition: ready for operation (used), Year of construction: 1989, Functionality: fully functional, For sale is a lathe of the brand Weiler type Primus LZ-GS The machine is in very good condition Technical data Year of construction 1989 Machine no. 4443 Operating voltage 380 V Center height 120 mm Center width 430 mm Speed:60 - 3000 rpm in 18 gear stages Spindle clearance 23 mm Short taper spindle head DIN 55027 Tailstock MK 2 Feed rates from 0.03 to 0.15 mm /rev Possible threads metric, inch, module and diametral pitch Metric thread pitches from 0.25 to 2.5 mm Length 1.2 m, height 1.3 m, depth 0.65 m Prices plus VAT Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale Bfgq8Jn0 PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: used, Year of construction: 1985, turning diameter 160 mm turning length 500 mm control Bosch CC 200 total power requirement kW weight of the machine ca. 4 t Cflt3P7Zza

Condition: refurbished (used), Functionality: fully functional, Weiler Primus VC precision center lathe 3-axis digital readout with VC drive infinitely variable speed and CE Overhauled with acceptance certificate for tolerances of new machines 6 months warranty !!! Technical data >> Machine no. 389 >> Center height 140 mm Bvme9Mj7 >> Center width 500 mm >> Spindle speed : up to 4000 rpm stepless >> spindle clearance 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.02 to 0.63 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 8 mm >> Weight approx. 800 kg >> Spindle brake can be activated >> Machine dimensions approx. 1.4 m x 1.55 m x 0.95 m Accessories and equipment: >> Siemens display NEW >> Collet chuck device with collets from 3 to 25 mm as good as new 1 mm increasing >> Three-jaw chuck 160 mm NEW with 2 sets of jaws >> Mulifix size A with 3 steel holders >> Electronic chip guard >> Machine lamp >> Machine feet >> Splash wall >> Splash wall >> Coolant device To the machine : Offered is a Weiler Primus VC lead and feed spindle lathe is in a geometrically overhauled condition. Overhauled with acceptance protocol for tolerances of new machine. The control takes over the functions in combination with a precision center lathe from Weiler: Graphic display of the traverse paths and traverse direction, graphic display of the measuring system on the lathe, calculation of tool corrections, zero offset for calculating the workpiece position, radius/diameter changeover, graphic display of the main spindle turning direction, graphic display of the position of the machine's speed potentiometer. The scales and display are new. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. The digital display from Siemens makes work even easier and more precise. Take the opportunity to inspect this machine on site under power and see for yourself the condition.

Condition: used, Year of construction: 1986, Machine/vehicle number: 100, turning diameter:160 mm turning length:500 mm weight of the machine ca.:4 t Bnj7Lmuc820 This machine comes from a training workshop. Technically, the machine is fully functional and in a well-maintained condition.

Year of construction: 1986, Condition: good (used), Machine/vehicle number: 3566, used center lathe WEILER PRIMUS LZ-G center height 120mm center width 420mm pole-changing motor 1,1/1,5 kW 18 spindle speeds from 60-3000 rpm 1 x three-jaw lathe chuck, 1 x four-jaw lathe chuck, rotating center punch, quick change tool holder Multifix with 3 inserts, Etfhqk7 with steady rest, manual clamping tube with sleeve, without collets, (for collet type 358E) Machine is located in 71334 Waiblingen-Beinstein and is available immediately. An inspection of the machine is possible after arrangement.

Year of construction: 1990, Condition: excellent (used), Bosch CC200 control Turning diameter 160 mm Turning length 460 mm Spindle speed 4000 1/min 12-station turret with 6 driven tools Spindle passage 70 mm Issehdu Tailstock Chip conveyor 3-jaw chuck Röhm Accessories

Year of construction: 2001, Condition: excellent (used), Machine/vehicle number: 402, Weiler Primus VC precision center lathe 3-axis digital display K&C NEW with VC drive stepless speed and CE very good condition Technical data: Juvoqh3Swl >> Year of manufacture 2001 Machine-No.402 >> center height 140 mm >> center distance 500 mm >> spindle speed : up to 4000 rpm infinitely variable >> spindle passage 40 mm >> short taper spindle head DIN 55027 size 5 with bayonet lock >> tailstock MK 3 >> feeds from 0,02 to 0,63 mm /U >> Possible threads metric , inch , module and diametral pitch >> Metric thread pitches from 0,25 to 8 mm >> Weight approx. 800 Kg >> Spindle brake can be switched on >> Dimensions of the machine approx. 1,4 m x 1,55 m x 0,95 m Accessories and equipment: >> 3 axis digital display K&C NEW >> Collet device with collets from 3 to 28 mm new 1 mm rising NEW >> three jaw chuck 160mm as new with 2 sets of jaws >> Mulifix size A with 2 pcs steel holders >> Electr. chip guard >> Machine lamp >> Splashboard To the machine : Offered is a Weiler Primus VC leading and traction spindle lathe year 2001 in a very good condition. A very nice lathe with VC drive stepless speed of the working spindle. The digital display and scales from K&C are new. This newer generation of Weiler lathes is very user friendly and surfaces can be produced like ground. The digital display from K&C makes working even easier and more accurate. Take the opportunity to inspect this machine on site under power and convince yourself of the condition.

Condition: used, turning diameter over bed 260 mm turning diameter over slide rest 140 mm turning length 500 mm centre height 125 mm bed width 160 mm spindle turning speed range 16: 110-3600 U/min spindle bore 28 mm face slide travel 120 mm upper slide-adjustment 120 mm tailstock quill taper MT 2 tailstock quill adjustment 80 mm drive motor 0,37 / 0,88 kW weight of the machine ca. 350 kg dimensions of the machine ca. 1,3 x 0,6 x 1,2 m Mechanic's lathe with manual feed and spindle support, drive via V-belt and Uc2Qkws2Q7 stepped pulleys as well as 2-pole motor, hardened, finely ground work spindle, support adjustment over the entire bed length using eccentric clamping lever, three-jaw chuck, collet device with pliers, crank tailstock, cast base. Machine dealer with own stock of 1600 m².

Condition: good (used), Lathe Lead and feed spindle lathe Type: Matador VS2 Manufacturer: Weiler Year of construction: ca. 1977-1980 Ucsnymgmpn Condition: The machine is used and has been completely cleaned. Machine dimensions: LxWxH: approx. 2000 x 500 x1500 mm Weight approx. 800kg

Condition: ready for operation (used), Year of construction: 2006, Heavy NC cycle lathe with movable bed. For technical data, please refer to the pdf supplement. Faceplate 1,300 mm. Up to 2 m turning diameter. 2 chip conveyors, front and rear. Dpknef Fagor control. 4-fold tool holder. A range of accessories.

Condition: used, Year of construction: 1988, turning diameter over bed 330 mm turning diameter over slide rest 185 mm turning length 750 mm centre height 165 mm spindle bore 40 mm turning speed range 32: 22 - 2800 U/min feed longitudinal 120: 0,015-0,3 mm/min metric thread 0,18 - 28 mm tailstock taper MT 3 Gpamyo total power requirement 1,5 / 3 kW weight of the machine ca. 1100 kg dimensions of the machine ca. 1,8 x 0,9 x 1,4 m Universal lathe in good condition with hardened and ground guides, 2-stage motor, 8-speed preselection gear, spindle brake and feed gear with 3 x 90 gears and equipped safety devices as well as a wide range of accessories. German quality brand. Machine from company workshop not from production. Thesale took place due to company closure. Machine dealer with own stock of 1600 m².