Used Emco Emcomat Fb-600 Mc for sale (146)

Condition: new, Machine according to DIN 8605: lathe with increased accuracy. Tip width: 700 mm Peak height: 170 mm Circulating diameter over bed: 340 mm Circulating diameter over flat slide: 190 mm Bed width: 260 mm Laengs schlitten: 600 mm Shifting path cross slide: 220 mm Shifting path upper slide: 110 mm Flat slide: 410 mm Flat slide width: 150 mm Guide load-length bed slide: 380 mm Rotary chisel cross-section: 20x20 mm Center of rotation distance - Upper slide: 34 mm Swing range upper slide (Support): 60/120° Main spindle: Spindle connection DIN 55029 (Camlock): S 5 Spindle bore: 50 mm Inner cone according to DIN 7178: 1:22 Spindle diameter in the front bearing: dia. 70 mm Max chuck diameter: 200 mm Max. washer diameter: 200 mm Spindle speeds: 40-3000 rpm Speed control: Stepless mechanical speed levels: 4 Main drive: Power at 40% ED: 5.3 kW Max rated torque a. d.Main spindle: 640 Nm Todpfxodctnbs Agcof Feed: 20 (28) Laengsvorschuebe Z: 0.045-0.787 mm/U 20 (28) Plan vorschuebe X: 0.023-0.406 mm/U Thread: 20 (28) metric thread (basic): 0.4 - 7.0 mm 32 inch thread (with option Raed replacement D3Z200): 56 - 4 Gg/inch 28 Module thread (with option Raed replacement D3Z200): 0.2 - 3.5 32 diam. Pitch thread (with option Raed replacement D3Z200): 112 - 8 Tailstock: Pinole diameter: 50 mm Indoor cone of the pinole: MK 3 Pinole stroke: 120 mm Side adjustment: x 13 mm Zulessige Werkstueckweights

Condition: good (used), Year of construction: 1996, x-travel: 380 mm y-travel: 140 mm quill stroke: 40 mm Tsdpfxoua E Naj Agcef table-size: 630 x 150 mm spindle taper MT: 2 voltage: 380/400 V

Condition: used, Year of construction: 2017, Emcomat E300 for sale. The machine was manufactured in 2017. Machine type: EM300x1500 SIEM Some repairs have been carried out and the following defects are known to us: Tedpow I S Uujfx Agcof Geometry checked. Z-guides in the area of the main spindle (chuck) are slightly worn. Z-slide tilts in X and Y under load up to 0.1mm; in this range, precise work is no longer possible at higher clamping pressure. Tool changer checked and adjusted. X-axis belt replaced and machine zero point set. Automatic band lubrication oil loss – troubleshooting performed, problem resolved, lubrication oil line renewed. Machine is operational – with reservation regarding Z-axis guidance.

Condition: like new (used), Year of construction: 2004, functionality: fully functional, travel distance X-axis: 450 mm, travel distance Y-axis: 300 mm, travel distance Z-axis: 350 mm, feed rate X-axis: 4 m/min, feed rate Y-axis: 4 m/min, feed rate Z-axis: 4 m/min, spindle speed (max.): 2,500 rpm, spindle speed (min.): 20 rpm, total height: 1,690 mm, total width: 1,480 mm, total length: 1,500 mm, table width: 400 mm, table length: 800 mm, type of input current: three-phase, table load: 400 kg, overall weight: 1,500 kg, input voltage: 380 V, workpiece weight (max.): 400 kg, input current: 16 A, input frequency: 50 Hz, milling length: 450 mm, Equipment: documentation/manual, Machine is complete with all accessories and tools three axes digital readout Heidenhahn X-axis range 450 mm Y-axis range 300 mm Z-axis range 350 mm Table length 800 mm Table width 400 mm Table load 400 Spindle speeds 2500 Rpm X-axis feed 0-4000 mm/min. Y-axis feed 0-4000 mm/min. Z-axis feed 0-4000 mm/min. Dimensions (Estimated) Length 1500 mm Width 1480 mm Tsdewnya Tjpfx Agcof Height 1690 mm Weight 1500 kg

Condition: like new (used), Year of construction: 2013, functionality: fully functional, Universal Tool Milling Machine Emco Emcomat FB-450 Linear with Position Indicator – Near-Mint Condition, CE-Compliant!! Technical Data: >> Year of manufacture: 2013 | Machine No.: F9A124962 >> Milling table clamping surface: 800 x 400 mm T-slots: 8 Slot width: 14 H8 Slot spacing: 50 mm Maximum load: 150 kg >> Infinitely variable spindle speeds: 10–5000 rpm >> Infinitely variable feed rates: 10–5000 mm/min Rapid traverse X-axis: 5000 mm/min >> Travel (X/Y/Z): 450/350/400 mm >> Vertical and horizontal quill – SK40 >> Hydraulic drawbar system >> Quill stroke: 80 mm >> Weight: approx. 2000 kg >> Dimensions (LxWxH): approx. 2.5 x 2 x 2 m >> Main drive motor: 10 kW Tjdpfowycv Iex Agcjf >> Spindle brake >> Technical documentation, spare parts plans, operating manual included >> Hinged safety enclosure >> Coolant system >> Machine lamp >> Dividing head >> Rotary table >> Machine vice >> Steady rest About the Machine: For sale is a Universal Tool Milling Machine Emco Emcomat FB-450 Linear with position display, in near-mint condition. The machine comes from a government operation and was used only occasionally for training purposes. The control system is very user-friendly. Additionally, the machine features hydraulic clamping in both vertical and horizontal operation. Conversion from vertical to horizontal mode is very simple due to the tilting vertical head. The Emco has been mechanically and electrically tested in our workshop. Take advantage of the opportunity to inspect and test the machine under power at our facility.

Condition: new, Year of construction: 2025, Immediately available stock machines subject to prior sale. Please contact us for an offer. Emcomat 14 D conventional lathe Tedodtmy Tepfx Agcjf center width 650 mm Center height 140 mm Max. Speed 4000 rpm Spindle connection size 4 (DIN 55029) Max. Drive power 7,5 kW Dimensions (LxWxH) 1280 x 1480 x 730 mm Machine is equipped with digital display. (Constant cutting speed within gear stage) As a regional factory representative of EMCO we offer maintenance, service and spare parts for conventional machines from EMCO. Visit our showroom in Stuttgart and contact us for a qualified consultation.

Year of construction: 2001, condition: excellent (used), Digital display Heidenhain. Slide travel range Slide travel longitudinal (X) 450 mm Carriage travel transverse (Y) 300 mm Slide travel vertical (Z) 350 mm clamping surfaces 800 x 400 mm Tool holder SK 40 quill stroke 100 mm Swiveling vertical milling head ± 90 Speed range 50-2500 rpm Machine dimensions: Length 1485 mm Tjdpenab A Nofx Agcjf width 1475 mm height 1475 mm Weight approx. 1500 kg

Condition: ready for operation (used), Year of construction: 2013, operating hours: 42,989 h, functionality: fully functional, Emco Emcomat 7 lathe and milling machine combination. Good technical condition. Single phase power supply, multi speed selection for lathe and milling machine. Forward and reverse lead screw. Comes with several spare parts / tools / stands. Tsdpfswm Eg Nsx Agcef Interested in buying? In the message, include your email address and phone number and I will contact you shortly.

Condition: like new (used), Year of construction: 2019, operating hours: 720 h, functionality: fully functional, machine/vehicle number: D4D194801, turning diameter over cross slide: 190 mm, spindle bore: 50 mm, turning diameter over bed slide: 340 mm, center height: 170 mm, spindle speed (max.): 3,000 rpm, The machine was used for training purposes and has only approximately 720 spindle hours. TECHNICAL DETAILS Center distance: 700 mm Center height: 170 mm Swing diameter over bed: 340 mm Swing diameter over cross slide: 190 mm Sliding movement of the longitudinal slide: 600 mm Sliding movement of the cross slide: 220 mm Sliding movement of the top slide: 110 mm Turning tool cross-section: 20 x 20 mm Drive motor power: 5.3 kW Main spindle Spindle nose: CAMLOCK DIN 55029 S5 Spindle bore: Ø 50 mm Maximum faceplate diameter: 200 mm Maximum chuck diameter: 200 mm Spindle speeds: 40 - 3,000 rpm Speed control: Continuously variable Speed settings: 4 Speed ranges: 40 - 130, 110 - 360, 310 - 1,070, 870 - 3,000 rpm Feed range Longitudinal feeds: 0.045 - 0.787 mm/rev Cross slide feeds: 0.023 - 0.406 mm/rev Thread cutting range Metric thread: 20 (0.4 - 7.0 mm) Tailstock Quill diameter: 50 mm Quill inner taper: MT 3 Quill stroke: 120 mm Lateral adjustment: ±13 mm Permissible workpiece weights Exposed: 50 kg With tailstock: 150 kg Tjdpfov Iqm Sjx Agcof MACHINE DETAILS Spindle hours: approx. 720 h Dimensions (L x W x H): 1,650 x 1,060 x 1,635 mm Turning spindle above floor: 1,103 mm Total weight: 755 kg Power supply: 400 - 440 V EQUIPMENT - 3-axis digital display - Continuously variable speed control - Röhm ZS Ø200 three-jaw chuck - 5 x B25/120 quick-change tool holders - Tool set - Fixed center MT 5 - Turning tool set with parting tool (3 x standard, 1 x parting)

Condition: ready for operation (used), Year of construction: 1997, functionality: fully functional, Machine available IMMEDIATELY with a wide range of accessories ex works Mayrhofen for a bid Tsdpfx Agsnk Uabocef

Condition: excellent (used), functionality: fully functional, Emcomat 17D Lead and Feed Screw Lathe with 3-Axis Digital Readout K&C New from Training Workshop Excellent Condition!!! Technical Data: >> Year of manufacture: approx. 2000 >> Machine no.: D3F H1 010 >> Centre height: 170 mm >> Swing over bed: 340 mm >> Swing over cross slide: 190 mm >> Turning length: 700 mm >> Spindle speed: 4 speed ranges, stepless from 35 to 3000 rpm >> Tailstock quill stroke: 120 mm >> Tailstock: MT3 >> Spindle bore: 50 mm >> 20 longitudinal feeds: 0.045 – 0.787 mm/rev >> 20 cross feeds: 0.023 – 0.406 mm/rev >> Required floor space approx. (L x D x H): 1.600 x 0.9 x 1.3 meters >> Weight: approx. 730 kg Equipment and Accessories: >> 3-axis digital readout from K&C, new, with 12 months manufacturer’s warranty and operating manual Functions: mm/inch switching, coordinate selection ABS/INC, value halving, reference point, tool programming for 200 tools, taper calculation, radius/diameter display, quick zeroing, count direction switching Todewvuf Tspfx Agcef >> 1 piece three-jaw chuck NEW 160 mm, 2 sets of jaws >> Multifix B toolholder with 2 tool pockets >> Chip guard >> Coolant system About the machine: Offered here is an Emcomat 17D lead and feed screw lathe, approx. year 2000, in very good condition. The machine is of course fully functional. The bedways are in excellent condition. The Emco is equipped with a new 3-axis digital readout from K&C and a new three-jaw chuck. Take the opportunity to inspect the machine under power on site and see the condition for yourself.

Condition: new, Year of construction: 2025, functionality: fully functional, spindle bore: 50 mm, center height: 170 mm, total length: 1,650 mm, total width: 1,060 mm, total height: 1,635 mm, spindle speed (max.): 3,000 rpm, spindle speed (min.): 40 rpm, rotational speed (max.): 3,000 rpm, rotational speed (min.): 40 rpm, overall weight: 755 kg, three-jaw chuck diameter: 200 mm, Equipment: rotational speed infinitely variable, New machine immediately available from our warehouse in Stuttgart. ( subject to prior sale) Whether prototype construction, maintenance or very important the training - the conventional and cycle-controlled machines of EMCO create here the balancing act and offer highest accuracy on smallest space and flexibility up to the detail. From possible accessories to the organization of the insertion, we are at your side with advice. Highlights of the EMCOMAT 17D Tedpsdq Rb Asfx Agcsf - Main spindle DIN55029 - Tailstock (off-center adjustable) - Single steel holder (clamping claw) - Belt drive for feed gear - Chuck protection with electric limit switch - Optional equipment such as coolant device, sliding chip guard doors, etc. Working range: - Travel in X/Y/Z: 220 / - / 710 mm - center distance: 700 mm - Center height: 170 mm Main spindle: - Max. Speed: 3000 rpm - Spindle connection: Size 5 (DIN 55029) - Max. Drive power: 5.3 kW Tailstock: - Internal cone: MK3 - quill stroke: 120 mm - inner taper of the quill: 50 mm The machine can be inspected in Stuttgart.

Condition: like new (used), Year of construction: 2021, operating hours: 470 h, functionality: fully functional, machine/vehicle number: D4D210301, turning diameter over cross slide: 190 mm, spindle bore: 50 mm, turning diameter over bed slide: 340 mm, center height: 170 mm, spindle speed (max.): 3,000 rpm, The machine was used for training purposes and has only approximately 460 spindle hours. TECHNICAL DETAILS Center distance: 700 mm Center height: 170 mm Swing over bed: 340 mm Swing over cross slide: 190 mm Sliding movement of the longitudinal slide: 600 mm Sliding movement of the cross slide: 220 mm Sliding movement of the top slide: 110 mm Turning tool cross-section: 20 x 20 mm Drive motor power: 5.3 kW Main spindle Spindle nose: CAMLOCK DIN 55029 S5 Spindle bore: Ø 50 mm Max. faceplate diameter: 200 mm Max. chuck diameter: 200 mm Spindle speeds: 40 - 3,000 rpm Speed control: Continuously variable Speed levels: 4 Speed ranges: 40 - 130, 110 - 360, 310 - 1,070, 870 - 3,000 rpm Feed range Longitudinal feeds: 0.045 - 0.787 mm/rev Cross slide feeds: 0.023 - 0.406 mm/rev Thread cutting range Metric thread: 20 (0.4 - 7.0 mm) Tailstock Quill diameter: 50 mm Tsdpfxsv Iqlze Agcof Quill inner taper: MT 3 Quill stroke: 120 mm Lateral adjustment: ±13 mm Permissible workpiece weights Exposed: 50 kg With tailstock: 150 kg MACHINE DETAILS Spindle hours: approx. 460 h Dimensions (L x W x H): 1,650 x 1,060 x 1,635 mm Turning spindle above floor: 1,103 mm Total weight: 755 kg Sound pressure level: 79 dB(A) Power supply: 400 - 440 V EQUIPMENT - 3-axis digital display - Continuously variable speed control - Röhm ZS Ø200 three-jaw chuck (soft jaws, internally and externally stepped) - 5 x B25/120 quick-change tool holders - Tool set - Fixed center MT 5 - Turning tool set (3 x standard, 1 x parting-off)

Condition: new, Year of construction: 2025, functionality: fully functional, center height: 200 mm, quill stroke: 120 mm, quill diameter: 50 mm, total length: 1,950 mm, total width: 1,060 mm, total height: 1,635 mm, spindle speed (max.): 3,000 rpm, spindle speed (min.): 40 rpm, rotational speed (max.): 3,000 rpm, rotational speed (min.): 40 rpm, three-jaw chuck diameter: 200 mm, Equipment: rotational speed infinitely variable, Whether prototype construction, maintenance or, most importantly, training - EMCO's conventional and cycle-controlled machines manage the balancing act and offer maximum accuracy in the smallest possible space and flexibility down to the last detail. Highlights of the EMCOMAT 20D- Main spindle DIN55029- Tailstock (eccentrically adjustable)- Simple steel holder (clamping claw)- Belt drive for feed gear- Chuck protection with electric limit switch- Optional equipment such as coolant device, sliding chip guard doors etc.Working range:- Travel in X/Y/Z: 220 / - / 1010 mm- Center distance: 1000 mm- Center height: 200 mmMain spindle:- Max. travel distance in X/Y/Z: 220 / - / 1010 mm- Max. travel distance in X/Y/Z: 220 / - / 1010 mm- Max. travel distance in X/Y/Z: 1000 mm Speed: 3000 rpm - Spindle connection: Size 5 (DIN 55029)- Max. speed: 3000 rpm - Spindle connection: Size 5 (DIN 55029)- Max. speed: 3000 rpm - Max. speed: 3000 rpm - Spindle connection: Size 5 (DIN 55029)- Max. speed: 3000 rpm Drive power: 5.3 kW Tailstock:- Inner cone: MK3- quill stroke: 120 mmm- inner cone of the quill: 50 mm Todpfx Aod D I Thjgcef

Condition: good (used), Year of construction: 2003, Internal item no.: 25045 Universal Milling Machine Emco FB4 Year: 2003 + Accessories (Hydraulic machine vice Allmatic 110 / 12x SK40 holders in rack) + Electrically tested until 11/2028 (as per inspection sticker) + 3-axis digital readout Heidenhain ND780 Travel: X 450 / Y 300 / Z 350mm Tedpfow Hrycex Agcof Quill stroke: 100mm Main drive: 3.2kW Speed range: 63 - 3150 rpm Milling table: 800x400mm Automatic central lubrication Dimensions (LxWxH): 200 x 200 x 200cm Weight: 2100kg

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, feed length X-axis: 700 mm, feed length Y-axis: 500 mm, feed length Z-axis: 500 mm, spindle speed (max.): 3,150 rpm, spindle speed (min.): 63 rpm, quill stroke: 100 mm, quill travel distance: 100 mm, total height: 2,120 mm, total width: 2,220 mm, total length: 2,150 mm, overall weight: 2,550 kg, As-new Emco FB6 milling machine (conventional) for sale. We purchased the machine in 2018 from a training workshop and have used it for only about 15 hours since then. (We acquired a 5-axis machining center for angular work...) We are selling the machine due to lack of space. Tjdoxga Sdjpfx Agcef The machine is in perfect condition and ready for immediate operation. Age-appropriate signs of use. The machine was manufactured in 2011. All technical details can be found in the attached photo. All tool holders shown in the photo are included, excluding the rack and the collets installed in the machine. The dividing head on the table is not included either. You are welcome to inspect the machine. For buyers from Switzerland, 8.1% VAT will be added to the price.

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, For sale: Well-maintained EMCO Hyperturn 665 MC Plus with IEMCA Master 880MP-E bar loader, chip conveyor, and high-pressure coolant pumps! Machine was exclusively used for machining brass parts! CNC Turning and Milling Center | EMCO Hyperturn 665 MC Plus with main and sub-spindle, C and Y axes, dual turrets each with 12 driven tool stations! Technical Data: Swing diameter over bed: 600 mm Tedpfx Ajxzq Ncjgcef Swing diameter over cross slide: 500 mm Control: Siemens Sinumerik 840D Max. turning diameter: 430 mm Max. turning length: 744 mm Max. bar capacity: 65 mm Travel - X: 270 mm Travel - Z: 750 mm Travel - X2: 205 mm Travel - Z2: 750 mm Travel - Y: 100 (+/- 50) mm Main spindle speed: 0 - 5,000 rpm Sub-spindle speed: 0 - 7,000 rpm Tool turret: 2x 12 positions, all driven! Tool holder: VDI 30 Upper turret: X, Z, Y axes Lower turret: X, Z axes Sub-spindle traverse (left/right): Z3 axis C11 spindle: 65 mm diameter (hollow chuck cylinder) C12 spindle: 45 mm diameter (solid chuck cylinder) with part ejector Tool turret type: Sauter 2x 14 bar high-pressure pumps Accessories: Complete tooling cabinet with driven and static toolholders as well as carbide inserts and tool holders Collet chucks for main and sub-spindle Full documentation etc. Machine available immediately! Ready for operation! Loading will be handled by us! Transport can be organized upon request!

Condition: defective spare-parts repository (used), Year of construction: 2000, functionality: not functional, machine/vehicle number: R2D N2802, turning diameter: 32 mm, The machine is still powered but not operational. The turret sub-spindle is defective. Tjdpexrdq Usfx Agcef

Condition: repair required (used), Year of construction: 2010, functionality: not functional, machine/vehicle number: M-075.068.10, feed length X-axis: 750 mm, feed length Y-axis: 500 mm, feed length Z-axis: 640 mm, spindle speed (max.): 12,000 rpm, spindle speed (min.): 50 rpm, table width: 520 mm, table length: 900 mm, CNC milling machine Emco MC 75/50 Machine no.: M-075.068.10 Tsdexn Hy Rspfx Agcsf Year of manufacture: 2010 includes 30 SK40 tool holders with pull studs includes 4th rotary axis includes various tools and holders includes coolant concentrate ATTENTION: Machine is being sold as needing repair. The machine control is defective: Heidenhain MC420 includes documentation and operating manual sold without guarantee or warranty

Condition: ready for operation (used), Year of construction: 2005, operating hours: 25,217 h, General Data Measurements width 3400 mm Measurements depth 2550 mm Measurements height 2300 mm Machine weight 8500 kg Control Unit Brand SIEMENS Model 840D Main Drive Number of spindles 2 Spindle speed range 5000 Movement X-Axis Movement 280 mm, X-Axis Rapid Traverse 24 m/min Y-Axis Movement 100 mm +/-50 mm Y-Axis Rapid Traverse 10 m/min Z-Axis Movement Z/Z2/Z3=900/750/750 mm Z-Axis Rapid Traverse 30 m/min Workpiece Workpiece X 744 mm Table Tslots size VDI40 Turret Number of turrets 2 Number of tool slots 12 Motorized tools VDI40 stations (both upper and lower turret) Media Power consumption 46 kVA Internal cooling Yes General Data Measurements width 3400 mm Measurements depth 2550 mm Measurements height 2300 mm Machine weight 8500 kg Control Unit Brand SIEMENS Model 840D Main Drive Number of spindles 2 Spindle speed range 5000 Movement X-Axis Movement 280 mm, X-Axis Rapid Traverse 24 m/min Y-Axis Movement 100 mm +/-50 mm Tedpfxsxfcrde Agcof Y-Axis Rapid Traverse 10 m/min Z-Axis Movement Z/Z2/Z3=900/750/750 mm Z-Axis Rapid Traverse 30 m/min Workpiece Workpiece X 744 mm Table Tslots size VDI40 Turret Number of turrets 2 Number of tool slots 12 Motorized tools VDI40 stations (both upper and lower turret) Media Power consumption 46 kVA Internal cooling Yes This 7-axis EMCO HYPERTURN 665 MC PLUS lathe was manufactured in 2005. It features twin spindles, twin turrets, and a maximum turning diameter of 600 mm. Equipped with a SIEMENS 840D CNC, it offers spindle speeds up to 5000 rpm and a bar passage diameter of 65 mm. Additional features include a LNS MOVE bar loading magazine, high-pressure coolant system, and air-conditioned control cabinet. For more information about this lathe, please reach out to us. Application Types Turning

Condition: used, Year of construction: 2003, Emco lathe enco Turn 420 MC with bar loader Tsdpfx Ageunzgrscjf condition see pictures

Condition: used, Year of construction: 2013, controller manufacturer: Siemens, controller model: 840Dsl, _____ Description: Year of manuf. : 2013 Control : Siemens 840Dsl Turning diam. : 430 mm Turning length : 744 mm Mainspindle: Technology:Motorspindle Speed:5.000 rpm Power (max.):29 kW Torque (max.):250 Nm Barcapacity:65 mm Workpiececlamping:Collet chuck, Hainbuch Spanntop nova Kombi Axzug Gr. 65 Subspindle: Technology:Motorspindle Speed:7.000 rpm Power (max.):22 kW Torque (max.):130 Nm Workpiececlamping:3-Jaw chuck, SMW Autoblok KNCS-N-225-66 Ejector:Pneumatic Movement in Z:750 mm Toolcarrier I (X/Y/Z): Todpfx Agsw Tg Adocjf Technology:Turret with 12 stations Taper:VDI30 Tooldrive:4.000 rpm, 6,7 kW, 25 Nm Movement in X/Y/Z:270/100/750 mm Eilgang in X/Y/Z:24/10/30 m/min Toolcarrier II (X/Z): Technology:Turret with 12 stations Taper:VDI30 Tooldrive:4.000 rpm, 6,7 kW, 25 Nm Movement in X/Z:205/750 mm Eilgang in X/Z:24/30 m/min Equipment/Accessory: Chipmanagement:Chip conveyor Coolingmanagement:Internal coolant pumps with High-pressure, 14 bar Rawmaterialfeed:Barloader, EMCO LM 1200 Finishedpartremoval:Workpiece unloading device (pneumatic) with conveyor belt Oilmistseparation:Mechanical extraction, Absolent Toolholder:Misc. static and driven toolholder Further Accessory:Spindlechiller

Condition: ready for operation (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: R6AP3801, turning length: 600 mm, turning diameter: 360 mm, controller model: Siemens CNC 840 D, TECHNICAL DETAILS Turning diameter: 360 mm Turning length: 600 mm Tsdpfx Agsw Em A Aecjf Control: Siemens CNC 840 D MACHINE DETAILS Operating voltage: 400 V~ Phases: 3/PE Frequency: 50/60 Hz Maximum current: 48 A Nominal current: 36 A Short-circuit current (Ik): 6 kA EQUIPMENT - Double spindle

Condition: excellent (used), Year of construction: 2011, operating hours: 10,111 h, functionality: fully functional, machine/vehicle number: M12400511, travel distance X-axis: 1,200 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 600 mm, spindle speed (max.): 12,000 rpm, number of slots in tool magazine: 30, TECHNICAL DETAILS Todpfxevrz Smj Agcof Control: Heidenhain TNC 620 X-axis: 1,200 mm Y-axis: 600 mm Z-axis: 600 mm 4th axis: included in delivery, dismantled Spindle Taper: SK 40 Max. speed: 12,000 rpm Condition: New spindle (2024), runs very smoothly Tool changer Capacity: 30 tools MACHINE DETAILS Control switch-on time: 34,597 h Program run: 11,726 h Spindle run time: 10,111 h

Condition: used, Year of construction: 2003, control 840D-PCU 50 V1 3 coolant ja Tedpfeqn A Rrex Agcof chip conveyor ja kW generator - rated current 110 A connected load 56 kW