Used Holzkraft Minimax Sc 4E 23 for sale (164)

Condition: new, - NEW-descriptionCutting plane directly on the saw bladeHeavy steel and cast iron constructionPrecision-guided format sliding carriage made of aluminium,anodized as standardLarge-area table extension guided on a telescopic arm andlongitudinally adjustableExtendable aluminum telescopic fence, angle adjustable with professionalstop flapsRip fence with quick release and fine adjustmentLarge work table made of milled gray cast iron stays permanently flatThe standard table extension and table extension enable easy work with larger workpiecesQuiet running and precise cutsEquipped with a powerful three-phase motorThe large dimensioned cast iron sawing unit is attached twice to the cast iron table and guarantees stability, precision, smooth running and a long service lifeMaximum cutting height is also achieved with the built-in scoring deviceEquipment details:Double cradle saw unitGenerously dimensioned, made of steel/cast ironClose to the saw blade, supported on both sides for precision, smooth running and a long service lifeAdjustable in height and up to 45° with a crankMaximum cutting height is also achieved with the built-in scoring deviceAlso available with scoring unittelescopic stopExtendable telescopic stop up to max. 2550 mmAngle adjustableWith professional stop flapsAluminum sliding carriageWith a thousand times proven ball contact systemInsensitive to dust and dirt due to minimal contact point between ball and trapezoidal rail10-year Holzkraft guarantee on wear and tear on the guidewaysRip fence with round rod guideWith fine adjustment and quick releaseStable round rod guide made of ground steel with a diameter of 45 mmCan be folded down as standard for cutting large workpiecesTechnical specifications:Dimensions and weightsWeight (net) approx. 380 kgConnection suctionSuction connection diameter 120 mmSuction connection diameter saw blade protection 60 mmMachine body length 1388 mmWorking area length 1000 mmMachine body width/depth 689 mmWorking area width/depth 2000 mmSpace required length 5118 mmSpace requirement width/depth 3830 mmelectrical dataConnection voltage 400 VDrive motor power 5.0 kWPhase(s) 3 PhNominal operating mode drive motor S6Type of current ACDuty cycle drive motor 40%Mains frequency 50 HzSliding carriage and tableFormat slide length 2250 mmTable length 840 mmFormat sliding carriage width 270 mmTable width 560 mmFormat sliding carriage height 124 mmTable height 900 mmcircular saw unitCutting width with rip fence 900 mmMax. cutting height 90° 90 mmMax. cutting width to the left of the saw blade 2310 mmMax. cutting height 45° 63 mmtrimming length 2250 mmSaw blade diameter 315 mmSaw blade inclination 90 - 45°Saw blade speed 4000 rpmArt. No. 5504323Ausziehbarer Teleskop-fence to max. 2550 mmWinkeladjustableMit Profi-AnschlagklappenAluminium-sliding tableMit tausendfach bewährtem KugelkontaktsystemStaub- and schmutzunempfindlich durch minimalen Berührungspunkt zwischen Kugel and Trapezschiene10 Jahright hand Holzkraft-guarantee on abrasion der Führungsbahnenrip fence with round rod guidingMit fine adjustment and quick clampingStabile round rod guiding aus geschliffenem steel with 45 mm diameterSerienmäßig tiltable for den Zuschnitt großer WerkstückeTechnische Daten:dimensions and Gewichteweight (Netto) ca.   380 kgAnschluss Absaugungsuction nozzle diameter   120 mmsuction nozzle diameter Sägeblattschutz   60 mmAufstellinformationenTransportbreite   900 mmErläuterung required spaceDie d... Gboljvyuqfohcdw Ejt

Condition: used, Year of construction: 2024, Used machine Year of manufacture: 2022 Commissioning: 8/2024 As-new condition The heavy-duty worktable made of highly ribbed grey cast iron and the base frame made of welded steel ensure high torsional rigidity and vibration-free operation. Smooth-running and precise sliding table made of anodised aluminium with proven, long-lasting ball contact system on hardened guides, 10-year warranty on guideway wear. Gbslhcsxua N Sodw Ejt Grey cast iron saw unit with permanently precise dual pivot segment guidance and zero-point tilt, 6-year Holzkraft warranty on wear of pivot segments. Equipped with a powerful three-phase motor. Saw blade tilt displayed on a scale at the unit. Large outrigger table with roller facilitates panel handling. Angle-adjustable aluminium telescopic fence with two professional folding stops. Folding parallel fence with quick-release and fine adjustment. Standard features include table extension, table widening, and eccentric clamp. Made in Italy Sliding Table and Worktable: Sliding table length: 2600 mm Sliding table width: 360 mm Sliding table height: 142 mm Worktable length: 840 mm Worktable width: 560 mm Worktable height: 900 mm Saw Unit: Cutting width with parallel fence: 900 mm Maximum crosscut width left of saw blade: 3200 mm Ripping length: 2660 mm Saw blade tilting range: 90 - 45° Maximum cutting height at 90°: 100 mm Maximum cutting height at 45°: 70 mm Note on max. cutting height: Independent of scoring unit Saw blade diameter: 315 mm Note on saw blade diameter: Independent of scoring unit Saw blade speed: 3800 rpm Motor: 5.5 kW The hose visible in the picture is not included in the scope of delivery! Availability: Short term Location: Flörsheim

Condition: new, Minimax ME 35 TR S Holzkraft Edge Banding Machine -Exhibition Machine- This offer is an equipment package. The following items and options are already included in the price: - New exhibition machine - Gbjlhcdjv Nhhpew Ejt

Condition: used, Year of construction: 2022, Used machine Year of manufacture: 2022 Equipment and technical data: - Professional sliding table saw in heavy-duty design - with scoring unit; externally adjustable with separate drive motor - format sliding carriage made of anodised aluminium with a proven and permanently smooth-running ball contact system on hardened guideways (10-year manufacturer's warranty from date of first commissioning) - saw rip fence with round-bar guide; foldable for large panels, with quick clamping and integrated fine adjustment - table extension - table widening - with integrated on/off switch on the sliding carriage - with motorised height and tilt adjustment of the saw unit, digital display for tilt - programmed control of the saw blade height and tilt and the position of the rip fence - swivelling control panel at eye level - Made in Italy quality - Trimming length: 3200 mm - Cutting height 90°/45° with scorer max.: 136.5/97 mm - Cutting-to-length width to the left of the saw blade max.: 3260 mm - Cutting width with rip fence: 1270 mm - Tilt of the saw blade: 90 - 45° - Saw blade diameter with scorer max.: 400 mm - Scoring saw blade: 120 mm - Speed main saw blade: 3500/5000 rpm - Speed scoring saw blade: 9200 rpm - Dimensions format sliding carriage: 360 x 142 x 3200 mm Gjlhszlbq Socdw Eobt - Extraction ports: 120 + 80 mm - Motor power: 7.0 kW, 400 V - Motor power scorer: 0.55 kW Dimensions: approx. 3200 x 950 mm Weight: approx. 745 kg Availability: at short notice Storage location: Röllbach

Condition: used, Year of construction: 2023, Used machine Golhcdwszk Nn As Ejbt Year of manufacture: 2023 Condition: as new, machine is unused Features and technical specifications: - Spindle speeds: 3,500 / 6,000 / 8,000 / 10,000 rpm - Milling spindle tilt: 0 to -45° - Useful length of the spindle: 125 mm - Spindle mandrel diameter: 30 mm - Speed display: LED display on the front of the machine - Max. tool diameter (standard): 240 mm - Maximum tool diameter that can be lowered: 230 mm - Maximum tool diameter for profile milling: 240 mm - Maximum tool diameter for tenon milling: 320 mm - Work table length: 1,200 mm - Work table width: 530 mm - Table height: 900 mm - Slide carriage length: 1,200 mm - Slide carriage width: 360 mm - Slide carriage height: 142 mm - Extraction nozzle diameter: 2 × 120 mm - Drive motor power: 5.0 kW - Mains voltage: 400 V - Mains frequency: 50 Hz Dimensions: 1,200 × 2,000 mm Weight: 510 kg Availability: at short notice Storage location: DE-63934 Röllbach

Condition: new, Year of construction: 2026, Holzkraft panel saw with scoring saw Compact panel saw with a pivoting saw blade and a high-quality, anodized aluminum crosscut fence The cutting plane of the compact panel saw is directly on the sliding table Precision-guided aluminum crosscut fence, anodized as standard Large table extension guided on a telescoping arm and adjustable in length The standard table widening and extension allow for easy work with larger workpieces The large-sized saw unit made of gray cast iron is double-mounted on the cast iron table and guarantees stability, precision, smooth running, and a long service life Large work table made of ground gray cast iron, making it extremely robust and durable Smooth operation and precise cuts Aluminum crosscut fence Equipped with a tried and tested ball bearing system Dust and dirt resistant due to minimal contact point between the ball and trapezoidal rail 10-year HOLZKRAFT warranty on wear of the hardened guide rails Telescoping fence Extendable aluminum telescoping fence Angle adjustable With two professional folding fences Ek2a0i2ik Parallel fence Standard with fine adjustment and quick clamping Scope of delivery: Table extension Table widening Anodized aluminum crosscut fence Parallel fence with round bar guide and fine adjustment Model SC 2 classic Item No. 5504215 Technical data Table dimensions 1020 x 325 mm Table height 900 mm Fence length 1660 mm Cutting height max. 90° with scoring saw 100 mm Cutting height max. 45° with scoring saw 79 mm Rip width max. to the left of the saw blade 1270 mm Cutting width with parallel fence 900 mm Saw blade tilt 90° - 45° Saw blade diameter max. with scoring saw 315 mm Saw blade diameter max. without scoring saw 315 mm Scoring saw blade diameter (optional) 80 mm Main saw blade speed 4000 min-1 Scoring saw blade speed 7600 min-1 Electrical connection 400 V / 50 Hz Motor power 4.0 kW Dust extraction nozzle diameter 120 mm Gbslhcdweih Dwvs Est Dust extraction nozzle diameter saw blade guard 60 mm Weight 295 kg Location: In stock at 54634 Bitburg - immediately available -

Condition: excellent (used), Year of construction: 2019, Combined jointer and thicknesser SCM minimax fs 41e Year of manufacture: 2019 Power of drive motor: 5 kW Connection voltage: 400 V Mains frequency: 50 Hz Planer cutterhead type: TERSA – 4 cutterheads Speed: 5200 rpm Planing width, max.: 410 mm Feed rate: 6 / 12 m/min Dust extraction port: 2, diameter for thicknessing: 120 mm Jointer Infeed table, length: 1034 mm Chip removal, max.: 5 mm Dimensions and weights, length: approx. 2000 mm Width/depth: approx. 1110 mm Height: approx. 1115 mm Weight: approx. 430 kg TERSA cutterhead system enables particularly quiet operation. Helically toothed steel infeed roller for consistent and uniform material feed. Material feed with two speeds. Numerical display for thickness table height. The 2,000 mm long jointer tables facilitate easy jointing of large workpieces. Work tables are made of gray cast iron, annealed and stress-relieved, making them resistant and permanently flat. Sturdy, large aluminum jointer fence with round bar guide (1200 x 160 mm) Thickness table adjustment via handwheel with numerical display for planing height. The high machine weight ensures the highest precision and smooth operation. Gbelhozi Nhmjcdw Ejt Powerful industrial motor Robust steel/gray cast iron construction.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, operating hours: 5 h, power: 5 kW (6.80 HP), input voltage: 400 V, pivoting range: 45 °, rotational speed (max.): 10,000 rpm, rotational speed (min.): 3,500 rpm, table width: 530 mm, table length: 1,200 mm, overall weight: 510 kg, tool diameter: 240 mm, Equipment: CE marking, Professional woodworking machine with tilting milling spindle and cantilever arm. Exhibition machine like new - used only for demonstration purposes Milling unit made from cast iron, tiltable up to -45° backwards Four milling speeds from 3500 to 10000 rpm Forward and reverse rotation Height and tilt display accurate to 0.1 mm Quick speed change via eccentric clamping Powerful 5.0 kW industrial motor Curved milling hood included Made in Italy Milling spindle tilt 0 – -45° Usable spindle length 125 mm Spindle speeds 3500/6000/8000/10000 rpm Speed indication via LED display on the front panel Spindle shaft diameter 30 mm Gelhcdwjyn Ny Us Eobt Max. tool diameter 240 mm Max. retractable tool diameter 230 mm Max. tenoning tool diameter 320 mm Accessories included: Mitre fence with two flip stops Eccentric clamp Curved milling safety guard Additionally, adjustable system fence jaws The machine can be inspected and tested at any time at the Chemnitz location.

Condition: new, Year of construction: 2025, machine/vehicle number: KK00050613, input frequency: 50 Hz, type of input current: three-phase, total length of planing tables: 2,250 mm, overall weight: 695 kg, chip removal: 5 mm, chip removal for surfacing (max.): 5 mm, number of planer blades: 4, planer shaft diameter: 120 mm, planing height: 240 mm, Equipment: motor brake, Holzkraft surfacer and thickness planer minimax fs 52 TERSA, Planing width 520 mm, planing height 3 - 240 mm, Gslhcdwsxn Suao Esbt Surfacing table length 2,250 mm, 4-knife TERSA cutterblock, Motor 7 kW (9.5 HP); S6 5 meter connection cable 2.5 mm² with 16 Ah plug, complete with: simultaneously foldable tables, combined extraction hood for surfacer and thicknesser D = 120 mm, Thickness table adjustment via handwheel with integrated readout, star-delta switch, auxiliary fence, CE and BG - wood dust certified. Order no.: 5503501 Available immediately ex location Seevetal, without transport, subject to prior sale.

Condition: new, HOLZKRAFT sc 2c sliding table saw - Exhibition machine - pivoting, rip fence with fine adjustment ----- Technical data ----- Extraction nozzle Ø: 120 / 60 mm, Work table height: 900 mm, Speeds: 4,000 rpm, max. saw blade Ø: 315 mm, Cutting width with rip fence: 900 mm, Cutting height 90/45°: 100 / 79 mm, cutting length: 1,600 mm, Gbolhcou R Sy Nsdw Eet Swivel range: 90 - 45 °, Dimensions (LxW): 1,020 x 325 mm, Weight: 295 kg - new exhibition machine -

Condition: new, Year of construction: 2025, Table saw/router combination minimax tw 45c With aluminum sliding table and pivoting router spindle – high performance at a low investment Article number 5502045 Brand Holzkraft / SCM TECHNICAL DATA Dimensions and weights Net weight approx. 290 kg Dust extraction connection Dust extraction port diameter 2 x 120 mm Work table Work table length 1000 mm, Sliding table length 1000 mm Work table width 435 mm, Sliding table width 270 mm Table height 900 mm Installation information Space requirement length 1945 mm, Machine body width/depth 710 mm Space requirement width/depth 2220 mm, Working area length 1600 mm Explanation of space requirement: The dimensions take into account maximum travel distances or usable lengths. Working area width/depth 1600 mm Machine body length 1000 mm, Explanation of working area: Please add the specified dimensions to the space requirement to obtain the recommended free installation area for the machine. Golehp Rcyohcdw Ejbt Electrical data Connection voltage 400V, Power of drive motor 5.0 kW Mains frequency 50Hz Router spindle Spindle inclination 0 to -45°, Spindle speed 3500/7000/10000 min⁻¹ Usable length of the spindle 100 mm, Spindle arbor diameter 30 mm Maximum spindle overhang above the table 130 mm Maximum router tool diameter Maximum tool diameter, plunge-cut 180 mm, Maximum tool diameter, mortising cutters 275 mm Maximum tool diameter, profile cutters 210 mm DELIVERY SCOPE Arched router guard Anodized aluminum sliding table Telescopic miter fence Aluminum fence cheek

Condition: excellent (used), Clearance height 90 cm, weight 478 kg, angle adjustment, table length 220 cm, motor 5 kW, cutting height 10 cm. Gelhcdwszkkqxs Esbt

Condition: new, Year of construction: 2026, Holzkraft Minimax ST 5es – Maximum configuration for professionals Saw-milling combination with miter cutting device and pivoting milling spindle Art. No.: 5501086 Ø 350 mm main saw blade with 118 mm max. cutting height, which is also achieved when the scoring saw blade is installed Gjlhcdjd Hx Hmow Eebt Scoring device with separate motor and Ø 120 mm saw blade, easily and precisely adjustable from the outside Saw unit can be pivoted from 90° to -45° High-precision format sliding table made of anodized aluminum Large extension table (1200 x 650 mm) With material roller and extendable aluminum telescope stop up to 3300 mm Pivoting milling spindle from 90° to -45° towards the rear into the milling fence Four milling speeds With right/left rotation of the milling spindle Three independent motors With lockable main switch, motor protection switch Supplied as standard with separate saw parallel fence and separate jointing fence for planing Equipment details: Sliding table with ball contact system Made of anodized aluminum Guides made of hardened and ground steel, 15% harder than conventional steel Double-bearing milling unit Pivoting, made of cast iron Mounting points directly on the table, resulting in optimal smoothness Milling spindle mounted high up on precision ball bearings, resulting in low bearing load and maximum possible service life Powerful industrial motors Milling fence Heavy-duty professional design The high-quality milling fence made of cast iron is supplied as standard with fine adjustment 3-way positionable for quick resetting of the setting With fine adjustment via rack and pinion, numerical display and aluminum milling fence jaws Parallel fence With fine adjustment and quick clamping Stable round bar guide made of ground steel Can be conveniently folded down for cutting large workpieces Interchangeable aluminum ruler for narrow workpieces Cast iron double-bearing saw unit Height adjustment via dovetail guide Extremely robust and torsion-resistant for precise cuts Close to the saw blade, bearing on both sides Height and adjustable up to 45° Scoring unit with separate scoring motor 0.55 kW as standard Extension table with angle-adjustable telescope stop with degree grid division Dimensions and weights Weight approx. 900 kg Dust extraction connection Dust extraction nozzle diameter 3 x 120 mm Dust extraction nozzle diameter saw blade guard 80 mm Drive power Scoring motor 0.55 kW Main motor 2 x 5.0 kW Electrical data Connection voltage 400 V Format sliding table and table Format sliding table width 360 mm Format sliding table height 142 mm Table length 1380 mm Table width 465 mm Milling spindle Spindle inclination 0 – -45 ° Usable length of the spindle 125 mm Spindle speeds 3500/6000/8000/10000 min⁻¹ Milling tool diameter max. Lowerable 240 mm Mortise milling 320 mm Circular saw unit and scoring saw Cutting length 3200 mm Cutting width with parallel fence 900 mm Max. ripping width to the left of the saw blade 3300 mm Saw blade inclination 90 - 45 ° Max. cutting height 90° 104 mm Max. cutting height 45° 68 mm Location: In stock, 54634 Bitburg - available immediately -

Condition: new, Year of construction: 2025, Gluing unit: Yes Edge thickness: maximum 3 mm Workpiece thickness: 8 mm - 50 mm Workpiece width: min. 110 mm Glue pot: granulate, quick-change pot End trimming shears: yes End trimming / flush cutting: yes Milling station: chamfer / radius Flat scraper blade: yes Radius scraper blade: yes Infeed fence adjustment: manual Workpiece thickness adjustment: manual Gbjlhcdexrbibjw Eot Power consumption: 5 kW Machine length: 3314 mm Machine width: 1085 mm Weight: 623 kg

Condition: new, Year of construction: 2025, Working width: 520 mm Planer block: Tersa Gslhcexrbgyjdw Esbt Number of knives: 4 Planing table length: 2250 mm Planing stop angle adjustable: yes Folding up the planing tables: manual Maximum thickness throughput of the thicknesser: 250 mm Thicknessing table height adjustment: electric Planing thickness display: digital Feed speed: 5/8/12/18 m/min Infeed roller: steel Outfeed roller: rubber Pressure beam: continuous Table rollers: no Motor power: 7 kW Motor brake: yes, automatic Extraction connection: 160 mm Machine length: 2300 mm Machine width: 1100 mm Weight: 695

Condition: new, Year of construction: 2025, Working width: 520 mm Cutterhead: Spiral cutterhead Number of knives: 4 Surface table length: 2250 mm Adjustable fence angle: yes Surface tables fold-up: manual Maximum thicknessing height: 250 mm Thickness table height adjustment: electric Planing thickness display: digital Feed speed: 5/8/12/18 m/min Infeed roller: Steel Outfeed roller: Rubber Pressure beam: continuous Table rollers: no Motor power: 7 kW Geloxrbhdjhcdw Eebt Motor brake: yes, automatic Extraction port: 160mm Machine length: 2300 mm Machine width: 1100 mm Weight: 695

Condition: new, Year of construction: 2025, Working width: 420 mm Planer shaft: Tersa Number of knives: 4 Jointer table length: 2000 mm Concave/pointed joint adjustment: no Adjustable jointer fence angle: yes Lifting jointer tables: manual Maximum thicknesser pass height: 240 mm Gelhjxrbg Hscdw Ejbt Thickness table height adjustment: electric Planing thickness display: digital Feed speed: 6/12 m/min Infeed roller: steel Outfeed roller: steel Pressure bar: continuous Table rollers: no Motor power: 5 kW Motor brake: yes, automatic Extraction port: 160 mm Machine length: 2300 mm Machine width: 1100 mm Weight: 450 kg

Condition: excellent (used), Year of construction: 2015, Holzkraft T 45 W classic Year of manufacture: 2015 Table saw with a robust steel-cast iron construction Tilts up to -45° Usable spindle length: 108 mm Max. tool diameter: 190 mm Table dimensions: 1000 x 435 mm Dimensions of aluminum sliding table: 1000 x 270 mm Motor: 4 kW, 400 V Gelhcdezzci Uow Eebt 3500/6000/8000/10000 rpm Equipped with a crosscut fence and sliding table Support arm on a swivel arm Aluminum telescope fence with folding stops and eccentric clamping device Otherwise, standard version Includes a 3-roller feed device

Condition: as good as new (ex-display), Year of construction: 2026, Combination 4-in-1 machine HOLZKRAFT CU 300 Classic F 23 N -- Technical Data -- - Circular Saw - Beam length 2,250 mm Max. saw blade diameter 315 mm Max. cutting height at 90°/45° 103 / 82 mm Max. support width to the left of the saw blade 2,310 mm Cutting width with parallel guide 820 mm Saw blade tilt 90° - 45° - Jointer - Working width 300 mm Jointer table length 1,510 mm Cutterhead diameter / Number of cutter knives 72 mm / 3 pcs. - Thicknesser - Table dimensions 300 x 585 mm Min./max. working height 3 / 230 mm Max. material removal 4 mm Feed rate 7 m / min - Table Router - Gjljci Tvhehcdw Ejbt Usable spindle length 100 mm Max. tenon tool diameter 275 mm Max. tool diameter 210 mm Spindle speed 3,500 / 7,000 / 10,000 rpm Spindle diameter 30 mm - General - Motor power 400 V / 50 Hz, 3 x 5.0 kW (6.6 hp) Dust extraction port diameter 4 x 120 mm Dust extraction port diameter on saw blade guard 60 mm - Promotional Price - Location: In stock, 54634 Bitburg

Condition: new, Year of construction: 2024, New machine Year of manufacture: 2024 Cutting plane directly on the saw blade Gbolhcdjwb Eh New Est Large-sized saw unit made of cast iron, double-mounted on the cast iron table – guarantees stability, precision, smooth operation, and long service life; 6-year HOLZKRAFT warranty on wear of the swivel segments Precision-guided format sliding table made of aluminum, anodized as standard 10-year HOLZKRAFT warranty on wear of the sliding table guide rails Parallel fence as standard with round bar guide and fine adjustment Large work table made of milled cast iron Smooth operation and precise cuts Standard table extension and table lengthening enable easy work with larger workpieces Extendable aluminum telescope fence with angle adjustment and two professional folding fences Made in Italy Motor 4.0 kW - 400 V Saw blade tilt 90 - 45° Format sliding table length 1600 mm Table length 1020 mm Table width 325 mm Cutting width with parallel fence 700 mm Max. cutting height 90° = 100 mm Max. cutting height 45° = 79 mm Saw blade diameter 315 mm Saw blade speed 315 mm Max. crosscut width to the left of the saw blade 1660 mm Scoring saw blade diameter 80 mm Scoring saw blade speed 7600 mm Weight: approx. 276 kg Note! The parallel fence and table extension on the right are not visible in the pictures. Availability: short-term Location: Flörsheim

Condition: new, Year of construction: 2025, Pre-milling unit: yes Pre-milling material removal: 0 - 2 mm Plastic edges: 0.4 - 3 mm Solid wood edges: 0.5 - 5 mm Workpiece thickness: 8 - 50 mm Minimum workpiece length: 120 mm Minimum workpiece width: 110 mm Anti-adhesive spray unit: yes Edge preheating device: yes Glue application unit: Granulate / quick-change glue tank kit End trimming unit: yes Flush end trimming unit: yes Corner rounding unit: yes Flush radius trimming unit: yes Radius scraper unit: yes Flat scraper unit: yes Gbjlhcdol D Rx Ujw Eet Buffing unit: yes Cleaning spray unit: yes Power consumption: 5 kW Machine length: 3,774 mm Machine width: 1,546 mm Machine height: 1,337 mm Weight: 842 kg

Condition: new, Year of construction: 2025, Edge banding unit: Yes Gslhcdsk Eai Uow Eebt Edge thickness: maximum 3 mm Workpiece thickness: from 8 mm - 50 mm Workpiece width: minimum 110 mm Glue pot: Granulate, quick-change pot Trimming cutter: yes Edge trimming / flush cutting: yes Routing station: Chamfer / radius Corner copying: yes Straight pull blade: Yes Radius pull blade: Yes Buffing unit: Yes Non-stick agent spray unit: Yes Infeed fence adjustment: manual Workpiece thickness adjustment: manual Power consumption: 5 kW Machine length: 3314 mm Machine width: 1085 mm Weight: 545 kg

Condition: new, Ideal for demanding craftsmen and carpentersThe particularly long dressing tables made of one piece enable easy dressing of the workpiecesWork tables are made of gray cast iron, making them robust and permanently flatRear-opening dressing tables with tension spring support for quick and easy retoolingThanks to the fixed extraction hood, it is not necessary to reposition the extraction hose during retooling, This saves valuable working timeHelically toothed steel infeed roller ensures constant and even wood infeedRubber outfeed roller in the thickness run-out ensures even wood outfeedMaterial feed with four speedsPlane thicknessing table adjustment via handwheel with integrated display for the planing heightDIGITAL: with electric thicknessing table height adjustment and digital displayOn/off switch in operator positionPowerful industrial motorThe high machine weight ensures maximum precision and smooth paration for slot drilling deviceQuality Made in ItalyTECHNICAL DATADimensions and weightsLength (product) approx. 2250 mm Width/depth (product) approx. 1370 mmWeight (net) approx. 695 kgJointerTotal length of tables 2250 mmChip removal max. Dressing 5 mmDressing fence length 1200 mmDressing fence height 150 mmSuction connectionSuction nozzle diameter thickness 1 x 120 mmInstallation informationSpace requirement length 2250 mmSpace requirement width/depth 1440 mmExplanation of space requirement: The dimensions take into account maximum travel distances or effective cknessThicknessing table length 520 mmThicknessing table width 850 mmWorking height thickness min. 3 mmWorking height thickness max. 240 mmWorking length thickness min. 220 mmChip removal max. thickness 5 mmElectrical dataDrive motor power 7 kWSupply voltage 400 VMains frequency 50 HzPlaner cutterheadPlaner shaft type TERSAPlaner shaft diameter 120 mmNumber of planer knives 4 pcsPlaner shaft speed 5000 min¯¹Planer width max. 520 mmFeedFeed speed 5/8/12/18 m/minSCOPE OF DELIVERYJointer-jointer fence with round bar guide4 feed speedsTersa planer shaftManufacturer no.5503501 Gbolhcdjvwflbjw Eot

Condition: new, - New -Description:- Top equipment for high productivity in a small space!- Intuitive operation with the eye-S control and 10"large touch screen: HMI Maestro Active Edge,Graphic display of all machining units and theiroperating status, Graphic simulation of machining operations,Control of all machining units, Regulationof glue tank temperature, Assistance functionsfor setting up the machine according to the machining program,Fault diagnosis for quick elimination of simple errors,Statistics on machining parameters, USB connection,Preparation for network connection, Preparation for Industry 4.0with data transmission protocol API REST- Excellent accessibility to the working aggregatesthanks to the large hood that ensures protection and noise reduction- Monoblock construction made of steel ensures high stabilityand rigidity of the machine- Automatic aggregate positioning when changingthe panel thickness- Automatic application of the strip edges with edge magazine(me 35 t s): The strip edges of solid wood areautomatically loaded and synchronized with the panel guide- Panel feed is made by feed chain with rubber glides- Extendable workpiece support- Adjustment of the infeed ruler via spacer platesTechnical data:Dimensions and weightsLength approx. 3314 mmHeight approx. 1300 mmWidth/depth approx. 1085 mmWeight approx. 545 kgflush radius milling unitflush radius milling unit input power 2 x 0,35 kWflush radius milling unit cutter speed 12000 min¯¹flush radius milling unit cutter diameter HM 55.3 mmFlush radius milling unit suction port diameter 2 x 60 mmElectrical dataSupply voltage 400 VMains frequency 50 HzGlue unitGlue tank input power 0,25 kWGlue tank suction port diameter 60 mmGlue tank working temperature 190 °CGlue tank filling quantity 0.8 kgPneumatic connectionOperating pressure 6.5 barAir consumption 470 l/minFeed rateFeed input power 5 kWFeed speed 7 m/minEdgesEdge thickness roll material 0.4 - 3.0 mmEdge thickness strip material - 5.0 mmPre-milling unitPre-milling unit input power 3 kWPre-milling unit diamond cutter diameter 80 mmPre-milling unit material removal ,5 / 2 mmpre-milling unit cutter speed 7200 min¯¹pre-milling unit cutter height 56 mmpre-milling unit exhaust diameter 2 x 80 mmscraper unitradius scraper 2 mmbuffing unitbuffing unit input power 2 x 0,14 kWbuffing unit speed 2800 min¯¹workpieceworkpiece thickness 8 - 50 mmworkpiece width min. 110 mmWorkpiece length min. 120 . 5507235 Gbjlevwfmlehcdw Est

Condition: new, Year of construction: 2026, Compact circular saw with a pivoting saw blade and a high-quality, anodized aluminum crosscut fence. The cutting plane of the compact circular saw is directly on the roller table. Precision-guided aluminum crosscut fence, anodized as standard. Large table extension guided on a telescoping arm and adjustable in length. The standard table extension and table widening allow for easy work with larger workpieces. The large saw unit made of cast iron is double-mounted on the cast iron table and guarantees stability, precision, smooth running and a long service life. Large work table made of ground cast iron, making it extremely robust and durable. Smooth operation and precise cuts. Aluminum crosscut fence. Equipped with a tried-and-tested ball contact system. Dust and dirt resistant due to minimal contact point between the ball and the trapezoidal rail. 10-year HOLZKRAFT warranty on wear of the hardened guide rails. Telescopic fence. Extendable aluminum telescopic fence. Angle adjustable. Golhcjcnxamedw Esbt With two professional folding fences. Parallel fence. Standard with fine adjustment and quick clamping. Scope of delivery: Table extension Table widening Anodized aluminum crosscut fence Parallel fence with round bar guide and fine adjustment Model: SC 2 classic Item No.: 5504215 Technical data Table dimensions: 1020 x 325 mm Table height: 900 mm Fence length: 1660 mm Cutting height max. 90° with scoring blade: 100 mm Cutting height max. 45° with scoring blade: 79 mm Cutting width max. to the left of the saw blade: 1270 mm Cutting width with parallel fence: 900 mm Saw blade tilt: 90° - 45° Saw blade diameter max. with scoring blade: 315 mm Saw blade diameter max. without scoring blade: 315 mm Scoring saw blade diameter (optional): 80 mm Main saw blade speed: 4000 min-1 Scoring saw blade speed: 7600 min-1 Electrical connection: 400 V / 50 Hz Motor power: 4.0 kW Dust extraction port diameter: 120 mm Dust extraction port diameter on the saw blade guard: 60 mm Weight: 295 kg Location: In stock at 54634 Bitburg - available immediately -