Used Holzkraft Minimax Lab 300P F16 Tersa for sale (177)

Condition: new, - NEW-descriptionCutting plane directly on the saw bladeHeavy steel and cast iron constructionPrecision-guided format sliding carriage made of aluminium,anodized as standardLarge-area table extension guided on a telescopic arm andlongitudinally adjustableExtendable aluminum telescopic fence, angle adjustable with professionalstop flapsRip fence with quick release and fine adjustmentLarge work table made of milled gray cast iron stays permanently flatThe standard table extension and table extension enable easy work with larger workpiecesQuiet running and precise cutsEquipped with a powerful three-phase motorThe large dimensioned cast iron sawing unit is attached twice to the cast iron table and guarantees stability, precision, smooth running and a long service lifeMaximum cutting height is also achieved with the built-in scoring deviceEquipment details:Double cradle saw unitGenerously dimensioned, made of steel/cast ironClose to the saw blade, supported on both sides for precision, smooth running and a long service lifeAdjustable in height and up to 45° with a crankMaximum cutting height is also achieved with the built-in scoring deviceAlso available with scoring unittelescopic stopExtendable telescopic stop up to max. 2550 mmAngle adjustableWith professional stop flapsAluminum sliding carriageWith a thousand times proven ball contact systemInsensitive to dust and dirt due to minimal contact point between ball and trapezoidal rail10-year Holzkraft guarantee on wear and tear on the guidewaysRip fence with round rod guideWith fine adjustment and quick releaseStable round rod guide made of ground steel with a diameter of 45 mmCan be folded down as standard for cutting large workpiecesTechnical specifications:Dimensions and weightsWeight (net) approx. 380 kgConnection suctionSuction connection diameter 120 mmSuction connection diameter saw blade protection 60 mmMachine body length 1388 mmWorking area length 1000 mmMachine body width/depth 689 mmWorking area width/depth 2000 mmSpace required length 5118 mmSpace requirement width/depth 3830 mmelectrical dataConnection voltage 400 VDrive motor power 5.0 kWPhase(s) 3 PhNominal operating mode drive motor S6Type of current ACDuty cycle drive motor 40%Mains frequency 50 HzSliding carriage and tableFormat slide length 2250 mmTable length 840 mmFormat sliding carriage width 270 mmTable width 560 mmFormat sliding carriage height 124 mmTable height 900 mmcircular saw unitCutting width with rip fence 900 mmMax. cutting height 90° 90 mmMax. cutting width to the left of the saw blade 2310 mmMax. cutting height 45° 63 mmtrimming length 2250 mmSaw blade diameter 315 mmSaw blade inclination 90 - 45°Saw blade speed 4000 rpmArt. No. 5504323Ausziehbarer Teleskop-fence to max. 2550 mmWinkeladjustableMit Profi-AnschlagklappenAluminium-sliding tableMit tausendfach bewährtem KugelkontaktsystemStaub- and schmutzunempfindlich durch minimalen Berührungspunkt zwischen Kugel and Trapezschiene10 Jahright hand Holzkraft-guarantee on abrasion der Führungsbahnenrip fence with round rod guidingMit fine adjustment and quick clampingStabile round rod guiding aus geschliffenem steel with 45 mm diameterSerienmäßig tiltable for den Zuschnitt großer WerkstückeTechnische Daten:dimensions and Gewichteweight (Netto) ca.   380 kgAnschluss Absaugungsuction nozzle diameter   120 mmsuction nozzle diameter Sägeblattschutz   60 mmAufstellinformationenTransportbreite   900 mmErläuterung required spaceDie d... Gsdpjvyuqfjfx Almebl

Condition: new, - NEW -- With TERSA cutter block for secondsChange planer knives- TERSA planing knife system enables particularlyquiet running- Helical-toothed steel feed roller forconstant and even wood intake- The particularly long planing tables from onePiece allow easy dressing of theWork pieces- Large planing fence can open when openingthe planing tables remain in position- Planing tables that open to the rear- The high machine weight ensures the highestPrecision and smooth running- Powerful industrial engine- Robust steel / cast iron construction- work tables are made of gray cast iron,post-annealed and stress-free, therebyinsensitive and permanently flat- Table lips for quiet runningEquipment detailsTERSA planing knife shaft- No more adjusting and screwing- Blade change in seconds- Self-locking- Particularly quiet- Perfect planing resultSuction hose connection- The suction nozzle of the planer and thicknesspoint in the same direction.- The hose connection is made by just oneSide off.- No hose is needed aroundthe machine passes ve- Stable chain drive- Steel drive wheels- Solid cast iron bearing blockPlaning mill- Prevent massive kickback protectionthe kickback of workpieces- TERSA planing knife shaft with three knivesensures an optimal planing patternThe material feed- Helical steel feed rollers for oneconstant and even material intakewithout prints- Multiple teeth grip at the same time for powerfulFeed- Wear-free in contrast to rubber feedrollingTechnical specifications:Length approx. 1725 mmWidth / depth approx. 880 mmWeight approx. 270 kgDressing chip removal max. 4 mmExtraction nozzle thickness 2 x 120 mmThick working height min. 3 mmThick working height max. 230 mmThickness of the chip removal max. 4 mmDrive motor power 4 kWConnection voltage 400 VMains frequency 50 HzPlaner knife shaft type TERSANumber of planing knives 3 pcsSpeed ??5200 min¯¹Planing width max. 300 mmFeed speed 7 m / minItem No. 5503031Storage location 97447 Gerolzhofen- free loaded- Gsdsvwgaaopfx Almjbl

Condition: new, - NEW -description- Stable cast steel construction- Milling spindle can be swiveled backwards from 0 ° to -45 °- Three spindle speeds from 3500 - 10000 rpm- As standard with right-left rotation of the milling spindle- Large-sized milling unit made of gray cast iron,attached directly to the table- Solid and precise gray cast iron table- Quick and easy speed change- Powerful 5.0 kW industrial motor- Standard curved milling protection hoodEquipment detailsAluminum sliding carriage- Equipped with a thousand times tried and testedBall contact system- torsion-resistant, extremely precise, smooth-running andproblem-free in daily use- 10 year Holzkraft guarantee on wear and tearof the guidewaysGray cast iron milling unit- Attached directly to the router table- Milling spindle mounted high up with precision ball bearings,thus the lowest possible bearing loadand the longest possible service life- 3 milling speeds from 3500 to 10000 rpmPowerful engines- Equipped with a powerful three-phase motorMilling protection- The milling protection is standard for maximum safetywith a height-adjustable guide railand ling stop- Exact milling stop with a quick adjustmentand a fine adjustment with a scale on the stop jaw- The integrated suction connection ensures a clear viewRouter table opening- A large router table opening also enablesthe use of larger flattening cuttersand tenoning and slotting toolsabove and below the tableArc milling protection hood- Included as standard in the scope of deliveryReversible stop jaws- Versatile integrated stop for bridgingthe tool gap- Allows you to work safely withnarrow workpiecesTechnical specifications:Dimensions and weightsWeight (net) approx. 290 kgConnection suctionExtraction nozzle diameter 2 x 120 mmWork tableWorking table length 1000 mmSlide length 1000 mmWorking table width 435 mmSlide carriage width 270 mmTable height 900 mmInstallation informationRequired space length 1945 mmMachine body width / depth 710 mmRequired space width / depth 2220 mmWorking area length 1600 mmExplanation of space requirementsThe dimensions take into account maximum travels or useful king area width / depth 1600 mmMachine body length 1000 mmExplanation of the work areaPlease add the specified dimensions with the space required in order to obtain the free installation area recommended for the ctrical dataConnection voltage 400 VMains frequency 50 HzPhase (s) 3 PhDrive motor power 5.0 kWType of current ACMilling spindleSpindle inclination 0 to -45 °Spindle speed (s) 3500/7000/10000 min¯¹Usable length of the spindle 100 mmSpindle mandrel diameter 30 mmSpindle overhang r table 130 mmMilling tool diameter l diameter can be lowered 180 mmTool diameter max. Tenon milling 275 mmTool diameter file milling 210 mmscope of deliveryArc milling protection hoodAnodized aluminum sliding carriageTelescopic miter fenceAluminum stop jawsItem No. 5502045 Gedpfx Alsvwf Ucsmjbl

Condition: new, DescriptionWork table made of heavily ribbed gray cast iron and base frame made of welded steel guarantee torsional rigidity and vibration-free operationUnique in this performance class: Format sliding carriage made of anodized aluminum for highest cutting precisionCutting plane directly on the saw bladeSwiveling saw blade from 90° - 45Trimming frame with aluminum crosscut fence and adjustable fence jaw for panels and large workpiecesMilling protection hood for profilingTwo independent motors for each working unitTECHNICAL DATADimensions and weightsWeight (net) approx. 190 kgSuction connectionSuction port diameter 120 mmSuction port diameter saw blade guard 60 mmElectrical dataSupply voltage 400 VMains frequency 50 HzNominal operating mode drive motor S6Duty cycle drive motor 40Power of drive motor 2 x 1.8 kWSliding carriage and tableLength of sliding table 1140 mmFormat sliding carriage width 201 mmHeight of format sliding carriage 70 mmtable length 1040 mmtable width 224 mmMilling spindlespindle mandrel diameter 30 mmuseful length of spindle 75 mmspindle speeds 5000/7500 min?¹Milling tool diameter l diameter max. 160 mmtool diameter max. tenon milling 200 mmCircular saw unittrimming length 1200 mmCutting width with rip fence 700 mmMax. Trimming width to the left of the saw blade 1200 mmSaw blade inclination 90 - 45Max. Cutting height 90° 75 mmMax. cutting height Cutting height 45°60 mmMax. Saw blade projection 90° 67 mmMax. saw blade Saw blade projection 45°40 mmDiameter (main) saw blade 250 mmSpeed (main) saw blade 4000 min?¹EquipmentAnodized aluminum sliding carriageTrimming frame with angle-adjustable crosscut fence with a folding stop and degree scaleSaw parallel stopEccentric clampTable wideningTrimming fence with wooden fence jawsManual height adjustment of the spindleSaw blade height adjustment manualsaw blade tilt adjustment manual&nbsp, Gjdpfxovwfqws Almebl

Condition: new, - new -BeschreibungMit TERSA cutter block for sekundenschnelles HobelmesserwechselnTERSA-Hobelmessersystem ermögclear opening particularly geräuscharmen Lonangular verzahnte steel input roller for konstanten and gleichmäßigen HolzeinzugDie particularly langen Abrichttische aus einem piece ermöglichen leichtes Abrichten der WerkstückeGroßer surface fence kann beim opening der Abrichttische in seiner Position bleibenNach rear öffnende AbrichttischeDas hohe Maschinengewicht sorgt for höchste Präzision and ruhigen LonLeistungsstarker Industrie-motorRobuste steel-/GraugusskonstruktionArbeitstische aus Grauguss, nachgeglüht and spannungsfrei, dadurch unempfindlich and dauerhaft planarsurfacing table lip plates for geräuscharmen LonAusstattungsdetails:TERSA-HobelmesserwelleKein Einstellen and Schrauben mehrHobelmesserwechsel in SekundenSelbstarretierendBesonders low noisePerfektes HobelergebnisAbsaugschlauch-AnschlussDie suction nozzle der surface planer and thickness zeigen in the selbe Schlauchanschluss erfolgt from nur einer side wird kein Schlauch benötigt, der um the machine veStabil ausgelegter KettenantriebAntriebsräder aus steelMassiver GraugusslagerbockHobelwerkMassive Rückschlagsicherungen verhindern den kick-back from WerkstückenTERSA-Hobelmesserwelle with three Messern sorgt for ein optimales HobelbildDer MaterialeinzugSchrägverzahnte Stahleinzugswalzen for einen konstanten and gleichmäßigen Materialeinzug without AbdrückeMehreright hand Zähne greifen gleichzeitig for kraftvollen feederVerschleißfrei im Gegensatz zu GummieinzugswalzenTechnische Daten:dimensions and Gewichtelength (Produkt) ca.     2015 mmweight (Netto) ca.     330 kgwidth/depth (Produkt) ca.     990 mmdrive powercapacity driving motor     5 kWsurface planertotal length der tables     1800 mmchip removal max. surface planer     4 mmworking height     900 mmAnschluss Absaugungsuction nozzle diameter thickness     2 x 120 mmAufstellinformationenrequired space length     2015 mmMaschinenkörper width/depth     596 mmrequired space width/depth    1 460 mmworking dimensions length     1000 mmErläuterung required spaceDie dimensions berücksichtigen maximale Verfahrwege or Nutzläking dimensions width/depth     3500 mmMaschinenkörper length     659 mmErläuterung zu working dimensionsDie angegebenen dimensions bitte with dem required space addieren, um the for the machine empfohlene freie assembly area zu cknessDickentisch length     605 mmworking height thickness max.     230 mmDickentisch width     420 mmchip removal max. thickness     4 mmworking height thickness min.     3 mmElektrische DatenAnschlussspannung     400 VStromart     ACPhase(n)     3 PhNetzfrequenz     50 HzHobelmesserwelleHobelwellentyp     TERSAHobelwellendrehzahl     5200 min¯¹Hobelwellendurchmesser     72 mmplaning width max.     410 mmnumber of Hobelmesser     3 Stfeederfeed speed     7 m/minincluded in deliveryTERSA-Hobelmesserwelleeloxierter Aluminium-surface fenceNo. 550 3414 Gedpfx Aevwga Hjlmobl

Condition: new, - new -manufactured by Holzkrafttype FS 41 elite S Tersa DigitalDigitale version with motorischer Dickentischverstellung- Hobelmessersystem ermögclear opening sekundenschnellescutter change soas particularly geräuscharmer Lon- Besonders lange Abrichttische (2200 mm)aus einem piece ermöglichen leichtes  Abrichten derWerkstücke- Arbeitstische sind aus Grauguss, nachgeglüht andspannungsfrei, dadurch unempfindlich and dauerhaft planar- Gleichzeitiges opening der tables- to rear, gleichzeitig öffnende Abrichttische for kurzeRüstzeiten- Leistungsstarker Industrie-motor- Festmontierte dust extraction hood- robuste steel-/Graugußkonstruktion- Gleichzeitiges opening der tables- großer surface fence (serial-production with auxiliary fence)- Materialvorschub with two speeds aboutspearatem motorTechnische Daten:total length der tables:  2200 mmworking width:   410 mmmax. chip removal: 5 mmthickness:dimensions Dickentisches: 775x410 mmmin/max. working height:  3/240 mmfeed speeds: 6/12 m/elwellen D./Hobelmesser: 95 mm/4 piecerpm:   5000 1/minmotor 400 V/50 Hz/S6 - 40 % 5,0 kW (6,6 PS)suction nozzle diameter: 1 x 120 mmweight:    450 kgArt-No.: 550 3441located in: 97447 Gerolzhofen- free on truck- Gbodpfxovwgc Us Almsl

Condition: new, With a 520 mm planing width, motorized thickness table adjustment, and comfort switching - Stable steel and cast iron construction - Large, ribbed jointer tables made of cast iron - Smooth operation due to high dead weight - Four feed speeds Gbedpfxexnqyho Almol - Motorized thickness table lift with two speeds and digital display - Segmented pressure beam at the infeed - Precision ball bearings on the four-knife cutterblock - Helical, hardened steel infeed roller for especially consistent and gentle wood feed - Outfeed roller with rubber coating - Large tiltable fence, adjustable from 90° to +45° - Standard auxiliary fence included - Powerful industrial motor - Pneumatic quick-change system with pneumatic raising and lowering of the jointer table - The extraction port remains in the same position for both jointing and thicknessing operations—no need for additional extraction hoses, inconvenient switching, or rerouting around the machine Scope of delivery: Technical Data: Dimensions and Weights: - Length (product): approx. 2300 mm - Width/Depth (product): approx. 1100 mm - Weight (net): approx. 980 kg Jointer: - Total table length: 2300 mm - Infeed table length: 1200 mm - Working height: 930 mm - Max. planing depth: 6 mm - Fence length: 1200 mm - Fence height: 190 mm - Fence tilt: 90 – 45° Extraction connection: - Extraction port diameter, thicknesser: 120 mm Installation Information: - Space requirement, length: 2300 mm - Space requirement, width/depth: 1610 mm Explanation: Max. travel paths or usable lengths are taken into account. - Machine body length: 1235 mm - Machine body width/depth: 850 mm - Working area length: 1000 mm - Working area width/depth: 3500 mm Note: Please add the working area to the space requirement to determine the recommended free installation space for the machine. Thicknesser: - Min. working height: 3.5 mm - Max. working height: 250 mm - Max. cutting depth: 8 mm Electrical Data: - Main drive motor power: 7 kW - Connection voltage: 400 V - Frequency: 50 Hz Cutterblock: - Cutterblock type: TERSA - Cutterblock diameter: 120 mm - Number of knives: 4 - Cutterblock speed: 5000 rpm - Max. planing width: 520 mm Feed: - Feed speed: 5/8/12/18 m/min

Condition: new, - New -Description:- Top equipment for high productivity in a small space!- Intuitive operation with the eye-S control and 10"large touch screen: HMI Maestro Active Edge,Graphic display of all machining units and theiroperating status, Graphic simulation of machining operations,Control of all machining units, Regulationof glue tank temperature, Assistance functionsfor setting up the machine according to the machining program,Fault diagnosis for quick elimination of simple errors,Statistics on machining parameters, USB connection,Preparation for network connection, Preparation for Industry 4.0with data transmission protocol API REST- Excellent accessibility to the working aggregatesthanks to the large hood that ensures protection and noise reduction- Monoblock construction made of steel ensures high stabilityand rigidity of the machine- Automatic aggregate positioning when changingthe panel thickness- Automatic application of the strip edges with edge magazine(me 35 t s): The strip edges of solid wood areautomatically loaded and synchronized with the panel guide- Panel feed is made by feed chain with rubber glides- Extendable workpiece support- Adjustment of the infeed ruler via spacer platesTechnical data:Dimensions and weightsLength approx. 3314 mmHeight approx. 1300 mmWidth/depth approx. 1085 mmWeight approx. 545 kgflush radius milling unitflush radius milling unit input power 2 x 0,35 kWflush radius milling unit cutter speed 12000 min¯¹flush radius milling unit cutter diameter HM 55.3 mmFlush radius milling unit suction port diameter 2 x 60 mmElectrical dataSupply voltage 400 VMains frequency 50 HzGlue unitGlue tank input power 0,25 kWGlue tank suction port diameter 60 mmGlue tank working temperature 190 °CGlue tank filling quantity 0.8 kgPneumatic connectionOperating pressure 6.5 barAir consumption 470 l/minFeed rateFeed input power 5 kWFeed speed 7 m/minEdgesEdge thickness roll material 0.4 - 3.0 mmEdge thickness strip material - 5.0 mmPre-milling unitPre-milling unit input power 3 kWPre-milling unit diamond cutter diameter 80 mmPre-milling unit material removal ,5 / 2 mmpre-milling unit cutter speed 7200 min¯¹pre-milling unit cutter height 56 mmpre-milling unit exhaust diameter 2 x 80 mmscraper unitradius scraper 2 mmbuffing unitbuffing unit input power 2 x 0,14 kWbuffing unit speed 2800 min¯¹workpieceworkpiece thickness 8 - 50 mmworkpiece width min. 110 mmWorkpiece length min. 120 . 5507235 Gjdpfevwfmlox Almsbl

Condition: new, Year of construction: 2025, FS 41 classic Tersa - Thicknessing planer with TERSA quick-change system for planing knives With TERSA cutterblock for changing planing knives in seconds TERSA planing knife system enables particularly quiet running Skew toothed steel infeed roller for constant and uniform wood infeed The extra long dressing tables made of one piece allow easy dressing of the workpieces Large dressing fence can remain in position when opening the dressing tables Rear opening dressing tables The high machine weight ensures highest precision and smooth running Powerful industrial motor Robust steel/cast iron construction Model FS 41 Classic Tersa Article-No. 5503414 Technical data ---Technical data dressing tables--- Total length of the tables 1800 mm Feeding table length 920 mm table height 870 mm working width 410 mm max. chip removal 4 mm ---Technical data thickness--- dimensions thickness table 605 x 420 mm min./max. working height 3 / 230 mm feed speed 7 m/min. planing shaft-Ø / planing knives 72 mm / 3 pcs. speed 5200 1/min motor 400V/50Hz/S6 40% 5,0 kW (6,6 PS) Gedpfx Ascnxayslmobl Suction nozzle diameter 2 x 120 mm Weight 270 kg Tersa planing cutter No more adjusting and screwing Change of planing knives in seconds Self-locking Especially low noise Planing mills solid backstops prevent the backstroke of workpieces 3-blade shaft Tersa for optimal planing pattern The wood infeed helical toothed steel infeed rollers for an

Condition: new, Year of construction: 2026, Maximum equipment for the professional. Multiple combination with TERSA cutterhead, miter cutting device and swiveling milling spindle. Ø 350 mm main saw blade with 118 mm max. cutting height, which is also achieved with the scoring saw blade installed Scoring device with separate motor and Ø 120 mm saw blade, easily and conveniently adjustable from the outside High-precision sliding carriage made of anodized aluminum on hardened and drilled steel guide rails Large boom (1200 x 650 mm) with roller and extendable aluminum telescopic fence up to max. 3300 mm Sawing unit swivels from 90° to -45 Pivoting milling spindle from 90° to -45° backwards into the milling fence Four milling speeds Right-left rotation of the milling spindle Quick change to thickness planer thanks to parallel opening jointer tables 2-stage feed in the thicknessing table Sharp toothed steel infeed roller for uniform wood infeed Three independent industrial motors With separate saw-parallel fence and separate feeder fence With lockable main switch Equipment details: Format fence Immediate control Boom Boom with angle-adjustable telescopic lay-off stop with graduation Sliding carriage with ball contact system made of anodized aluminum guides in hardened and ground steel F550S, 15% harder than conventional steel guides riveted and not glued light running, low noise and reliable 10 years HOLZKRAFT warranty on wear of hardened guideways cast iron double cradle saw unit height adjustment via dovetail guide extremely robust and torsionally stiff for precise cuts close to the saw blade, mounted on both sides height and inclination adjustable up to 45 standard scoring unit with separate scoring motor 0,55 kW double cradle scoring unit large-dimensioned swiveling double cradle milling unit made of cast iron milling stop heavy professional design the high quality cast iron fence is supplied with fine adjustment as standard 3-fold positionable for fast readjustment of the setting with fine adjustment via toothed rack, numerical display and aluminum fraise stop jaws Planer steel infeed rollers with helical teeth for a constant and uniform wood infeed solid backstops prevent the backstroke of workpieces 4-knife torsion shaft ensures an optimal planing pattern table lips for a quieter running Tersa planing cutterhead No more adjusting and screwing Change of planing knives in seconds Self-locking Gbjdpfx Aljcnxa Somol Especially low noise Thicknessing table The thicknessing table is mounted on four large-dimensioned spindles, which ensure high stability under all working conditions. Due to the special lifting device, the table position is perfectly maintained even without locking. Rip fence with fine adjustment and quick clamping stable round bar guide made of ground steel reversible aluminum ruler no measuring gap, guide rods are overlapping Separate dressing fence large professional design (1800 x 150 mm) 0-45° swiveling with quick adjustment stable round bar guide made of ground steel simultaneous opening Art: No. 5500557

Condition: new, Year of construction: 2025, Surface planer minimax fs 41es TERSA Maximum equipment for the professional. Part number 5503431 Brand Holzkraft / SCM Diagonally toothed steel feed roller for constant and even material feed, resulting in chip removal from as little as 0.2 mm (with min. workpiece thickness of 3 mm) - ideal for economical planing of precious woods Models with TERSA cutterblock for changing planing knives in seconds and particularly quiet running Material feed with two speeds Particularly long dressing tables allow easy and precise dressing of workpieces Work tables made of gray cast iron, annealed and stress-free, thus insensitive and permanently flat Dressing tables opening to the rear simultaneously for short set-up times Gbjdpfx Aljlht Htomol Planer thickness table adjustment via handwheel with numerical display for planer height Cgiptddi High machine weight for maximum precision and smooth running Powerful industrial motor Robust steel/cast iron construction Quality - Made in Italy TECHNICAL DATA Dimensions and weights Length (product) approx. 2200mm Weight (net) approx. 450kg width/depth (product) approx. 1160mm Dressing table Total length of tables 2200mm Dressing fence length 1200mm Working height 905mm Dressing fence height 150mm chip removal max. dressing 5mm Connection suction Suction port diameter thickness 1 x 120mm Thickness thickness table length 775mm working height thickness max. 240mm Thickness table width 410mm Chip removal max. thickness 5mm Working height thickness min. 3mm Electrical data Power drive motor 5kW Mains frequency 50Hz Supply voltage 400V Planer cutterhead Planing shaft type TERSA Planing shaft speed 5000min¯¹ Planing shaft diameter 95mm Planing width max. 410mm Number of planing knives 4pcs Feed rate feed speed 6 / 12m/min SCOPE OF DELIVERY Planer jointing fence with round bar guide & auxiliary fence Two feed speeds Tersa planer shaft Location: Ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2026, Combined saw-milling machine minimax st 3c F 16 Swiveling saw blade, swiveling milling spindle and format sliding carriage made of anodized aluminum Sturdy cast steel construction Large support surface and precise cast table High-precision sliding carriage made of anodized aluminum (travel 2250 mm) Large trimming frame (900 x 600 mm) with telescopic aluminum fence extendable up to 2660 mm with professional stop flaps Max. Saw blade Ø 315 mm with scoring device, tiltable from 90° - 45 Saw parallel fence with fine adjustment Stable saw unit and large dimensioned double cradle milling unit guarantee highest stability, precision, smooth running and long service life Solid and precise machine table made of stress-free gray cast iron Three milling speeds, manually adjustable from 3500 - 10000 min-¹ With right-left rotation of the milling spindle Standard arc milling protection hood Safety turning stop jaws made of aluminum Two motors with high power reserves Two plug-in handwheels for convenient and quick operation Dimensions and weights Weight approx. 470 kg Connection suction Suction port diameter 2 x 120 mm Suction port diameter saw blade guard 60 mm Electrical data Power drive motor 2 x 5,0 kW Supply voltage 400 V Mains frequency 50 Hz Gbsdpfehp Rdlsx Almol Milling spindle spindle inclination 0 - -45 ° useful length of spindle 100 mm spindle speeds 3500/7000/10000 min-¹ Milling tool diameter max. not lowerable 210 mm lowerable 180 mm tenon milling 275 mm K

Condition: as good as new (ex-display), Year of construction: 2026, Combi 4-way HOLZKRAFT CU 410c F 26 N Tersa -- Technical data -- - Circular saw - Gedpsd Dtc Tofx Almjbl circumference 2.600 mm max. saw blade Ø 315 mm max. cutting height at 90°/45° 100 / 79 mm max. clearance width left of saw blade 2.310 mm cutting width at rip fence 900 mm saw blade tilt 90° -45° - Dressing - working width 410 mm planing table length 1.660 mm planing shaft Ø / number of planing knives 72 mm / 3 pcs. - Thickness table dimensions 410 x 605 mm min./max. working height 3 / 230 mm max. chip intake 4 mm feed speed 7 m / min -table milling machine - useful length spindle 100 mm max. tenon tool Ø 275 mm max. tool Ø 210 mm spindle speed 3.500 / 6.000 / 10.000 rpm spindle Ø 30 mm - General - motor power 400 V / 50 Hz, 3 x 5,0 kW (6,6 PS) Suction nozzle-Ø 4 x 120 mm suction nozzle-Ø saw blade protection 60 mm - Special offer price - Location: Ex stock 54634 Bitburg

Condition: new, Year of construction: 2025, Sturdy cast steel construction With rigid milling spindle 3 spindle speeds 3500 to 10000 min¯¹ Milling spindle with right-left rotation Large dimensioned milling unit made of grey cast iron, directly mounted to the table With suction hood under the worktable for better extraction Solid and precise cast iron table Quick and easy speed change Powerful motor with 5,0 kW Standard arc milling protection hood Quality Made in Italy Equipment details Cast iron milling unit Directly mounted on the milling table Milling spindle mounted high up with precision ball bearing, thus lowest possible bearing load and longest possible service life 3 milling speeds from 3500 to 10000 min¯¹ Powerful motors equipped with powerful three-phase motor Milling guard The standard milling guard is equipped with a height-adjustable guide rail and guard plate as standard for maximum safety. Milling fence Precise milling fence with a quick adjustment and a fine adjustment with scale on the fence jaw. The integrated suction connection ensures a clear view Milling table opening A large milling table opening also allows the use of larger flattening cutters and tenoning and slotting tools above and below the table Curved milling protection hood Included as standard Reversible fence jaws versatile integratable stop for bridging the tool gap enables safe working even with narrow workpieces Gsdpohp Rcrsfx Almebl TECHNICAL DAY

Condition: as good as new (ex-display), Year of construction: 2025, Minimax ti 55es LL - spindle moulder Figure shows 55 i T s standard version elite The professional craftsman machine with Swivel Milling spindle and 4 speeds. M Digital: motorized height adjustable and Tiltable Stable steel-cast iron construction Large dimensioned milling unit of grey cast iron, swivel up to 45 ° to the rear Display of the cutting speeds by LEDs Quick and easy change of speed of eccentric tension Right left rotation Display height and inclination 1/10 mm exactly Shaper fence heavy-duty professional: with fine adjustment via rack and pinion, with numerical display, ALU stop baking, 3-fold positioned for quick repeat of setting Scope of delivery: Aluminium milling stop baking Milling wheel arch guard Extension table left and right Model minimax ti 55es LL Item No. 5502252 Technical data Dimensions of the working table 2500 x 655 mm Formatschiebeschlitten commercial length of spindle dimensions 125 mm Max tool diameter 240 mm Gjdpfx Ajdqzh Rolmebl Max tool diameter lowerable 230 mm Max tool-Ø pin cutter 320 mm Spindle inclination 0-45 degree Speed 3500/6000/8000/10000 min-1 Engine power 400 V / 50 Hz / S6-40% 5.0 kW Suction nozzle diameter 2 x 120 mm

Condition: new, Year of construction: 2026, Holzkraft Minimax ST 5es - Maximum equipment for professionals Saw-milling combination with miter cutting device and swiveling milling spindle Art. No.: 5501086 Ø 350 mm main saw blade with 118 mm max. cutting height, which is also achieved when the scoring saw blade is installed Scoring unit with separate motor and Ø 120 mm saw blade, easily and precisely adjustable from the outside Saw unit can be tilted from 90° to -45 High-precision format sliding carriage made of anodized aluminum Large extension arm (1200 x 650 mm) With material roller and extendable aluminum telescopic fence up to 3300 mm Pivoting milling spindle from 90° to -45° backwards into the milling fence Four milling speeds With right-left rotation of the milling spindle Three independent motors With lockable main switch, motor protection switch With separate saw-parallel fence and separate jointing fence for dressing as standard Gsdpod Hx Hmjfx Almjbl Equipment details: Sliding carriage with ball contact system Made of anodized aluminum Guides made of hardened and ground steel, 15% harder than conventional steel Double cradle milling unit Swiveling, made of cast iron Fixing points directly on the table, thus optimal running smoothness Milling spindle mounted far up on precision ball bearings, thus low bearing load and longest possible service life Powerful industrial motors Milling stop Heavy-duty professional version The high-quality milling fence made of cast iron is supplied with fine adjustment as standard 3-fold positionable for quick return of the setting With fine adjustment via toothed rack, numerical display and aluminum milling stop jaws Rip fence With fine adjustment and quick clamping Sturdy round bar guide made of ground steel Conveniently folds down for cutting large workpieces Reversible aluminum ruler for narrow workpieces Cast iron double weigh saw unit Height adjustment via dovetail guide Extremely robust and torsion-resistant for precise cuts Close to the saw blade, mounted on both sides Height and up to 45° inclination adjustable Scoring unit with separate scoring motor 0.55 kW as standard Boom with angle-adjustable telescopic crosscut fence with degree raster graduation Dimensions and weights weight approx. 900 kg Connection dust extraction diameter of dust extraction nozzle 3 x 120 mm Suction port diameter saw blade guard 80 mm Drive power scoring motor 0,55 kW main motor 2 x 5,0 kW Electrical data Supply voltage 400 V Format sliding carriage and table Width of sliding table 360 mm height of sliding table 142 mm Table length 1380 mm table width 465 mm Milling spindle spindle inclination 0 - -45 ° useful length of spindle 125 mm spindle speeds 3500/6000/8000/10000 min-¹ Milling tool diameter max. lowerable 240 mm tenon milling 320 mm Circular saw unit and scoring unit trimming length 3200 mm Cutting width with rip fence 900 mm Max. Trimming width to the left of the saw blade 3300 mm saw blade inclination 90 - 45 °. Max. Cutting height 90° 104 mm Max. Cutting height 45° 68 mm Location: Ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, 4-knife shaft for best results of Planer Smooth running thanks to precision unit and the heavy casting Front steel feed roller with helical gearing for an optimum feed Satin Steel pull-out roller, optionally with squeegee in the excerpt The working table is mounted on four large pillars that ensure the greatest stability under all operating conditions. The thickness table is adjusted by a Handwheel with numeric display for the planing height (exactly 1/10 mm) Equipped with two speeds, of user facing the front of comfortable selectable Powerful industrial motor Stable steel-cast iron construction Gbedpfx Alod Hx Hnomol Equipment details: Work table Stored on four großdimensonierten screws ensure the stability of the largest under all working conditions Special lifting device correctly maintain the table position, also without lock Tersa Planer knife shaft No adjust and screw more Planer blades change in seconds Self arretierend Particularly low noise Thickness table adjustment at 41 S elite s through a Handwheel with numeric display for the planing height (exactly 1/10 mm) Dimensions and weights Length approx. 900 mm Width/height 1070 mm Weight approx. 361 kg Connect dust extraction Suction nozzle diameter 120 mm thickness Drive performance 5 main motor kW Installation information Space length 1070 mm Space width/depth 900 mm Space height 1100 mm

Condition: new, Year of construction: 2025, Table milling machine minimax tw 45c With aluminum sliding carriage and swiveling milling spindle - high performance for a low investment Item number 5502045 Brand Holzkraft / SCM TECHNICAL DATA Dimensions and weights weight (net) ca. 290kg Connection suction suction connection diameter 2 x 120mm Working table Working table length 1000mm Sliding carriage length 1000mm working table width 435mm sliding carriage width 270mm table height 900mm Installation information Space requirement length 1945mm machine body width/depth 710mm Space requirement width/depth 2220mm Working area length 1600mm Explanation of space requirements The dimensions take into account maximum travels or useful lengths. Working area Width/depth 1600mm Machine body Length 1000mm Explanation Working area Please add the dimensions given with the space requirement to obtain the free installation area recommended for the machine. Electrical data Supply voltage 400V Power drive motor 5,0kW Mains frequency 50Hz Milling spindle Spindle inclination 0 to -45° Spindle speed(s) 3500/7000/10000min¯¹ Useful length of spindle 100mm Spindle mandrel diameter 30mm spindle protrusion max. over table 130mm Milling tool diameter max. Tool diameter max. lowerable 180mm Tool diameter max. tenon milling 275mm Gjdpfshp Rcyox Almjbl tool diameter max. profile milling 210mm SUPPLY Arch milling protection hood Anodized aluminum sliding carriage Telescopic miter fence Aluminum stop jaws

Condition: new, Year of construction: 2026, Holzkraft sliding table saw with scoring device Cut-size circular saw with tiltable saw blade and high-quality sliding table made of anodized aluminum Cutting plane of the small-format circular saw directly on the roller table Precision-guided sliding table made of anodized aluminum, standard finish Large table arm guided on telescopic arm and longitudinally adjustable The standard table widening and table extension allow easy working with larger workpieces The large dimensioned sawing unit made of cast iron is double mounted on the cast iron table and guarantees stability, precision, smooth running and a long service life. Large work table made of ground cast iron, therefore extremely robust and insensitive smooth running and precise cuts Aluminum sliding carriage With millionfold proven ball contact system Insensitive to dust and dirt due to minimal contact point between ball and trapezoidal rail 10 years HOLZKRAFT warranty on wear of hardened guideways Telescopic stop Extendable aluminum telescopic stop Angle adjustable With two professional folding fences Ek2a0i2ik Rip fence Standard with fine adjustment and quick clamping Scope of delivery: Table extension Table extension Anodized aluminum format sliding carriage Rip fence with round bar guide and fine adjustment Model SC 2 classic Article no. 5504215 Gbjdjih Dwvepfx Almjl Technical data table dimensions 1020 x 325 mm table height 900 mm trim length 1660 mm cutting height max. 90° with scoring 100 mm cutting height max. 45° with scoring 79 mm max. clearance width to the left of the saw blade 1270 mm Cutting width with rip fence 900 mm saw blade inclination 90° - 45 saw blade Ø max. with scoring 315 mm saw blade Ø max. without scoring 315 mm scoring saw blade Ø (option) 80 mm Main saw blade speed 4000 min-1 Speed scoring saw blade 7600 min-1 Electrical connection 400 V / 50 Hz motor power 4,0 kW Suction nozzle diameter 120 mm Suction nozzle Ø saw blade guard 60 mm Weight 295 kg Location: Ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, 4-knife shaft for best results of Planer Smooth running thanks to precision unit and the heavy casting Front steel feed roller with helical gearing for an optimum feed Satin Steel pull-out roller, optionally with squeegee in the excerpt The working table is mounted on four large pillars that ensure the greatest stability under all operating conditions. The thickness table is adjusted by a Handwheel with numeric display for the planing height (exactly 1/10 mm) Equipped with two speeds, of user facing the front of comfortable selectable Powerful industrial motor Stable steel-cast iron construction Equipment details: Work table Stored on four large screws, ensure the stability of the largest under all working conditions Special lifting device correctly maintain the table position, also without lock Tersa Planer knife shaft No adjust and screw more Planer blades change in seconds Self arretierend Godjd Hx Hpopfx Almsbl Motor thickness table height adjustment at 52 S elite s Height adjustment of the Thicknesser table motor with electronic number For greater precision and more ease of use Dimensions and weights Length approx. 1080 mm Width/depth approx. 1440 mm Weight 455 kg Connect dust extraction Suction nozzle diameter 120 mm thickness Drive performance 7 main motor kW Installation information Space length 1440 mm Space potatoes

Condition: new, Minimax ME 35 TR S Holzkraft Edge Banding Machine -Exhibition Machine- This offer is an equipment package. The following items and options are already included in the price: - New exhibition machine - Gjdpfx Aev Nhhpolmsbl

Condition: new, Year of construction: 2024, New machine Year of manufacture: 2023 Approximate dimensions: Length: 2,300 mm Width/Depth: 1,100 mm Weight: 980 kg Total table length: 2,300 mm Infeed table length: 1,200 mm Working height: 930 mm Maximum cutting depth: 6 mm Fence length: 1,200 mm Fence height: 190 mm Fence tilting range: 90° - 45° Thicknesser extraction port diameter: 120 mm Main motor: 7 kW Space requirement length: 2,300 mm Space requirement width/depth: 1,610 mm Space requirement explanation: The dimensions include maximum travel paths or usable lengths. Machine body length: 1,235 mm Machine body width/depth: 850 mm Length: 1,000 mm Width: 3,500 mm Note on working area: Please add the specified dimensions to the space requirement to determine the recommended clear installation area for the machine. Minimum working height: 3.5 mm Maximum working height: 250 mm Maximum cutting depth: 8 mm Connection voltage: 400 V Phases: 3-phase Current type: AC Gbodextgz Ejpfx Almsl Mains frequency: 50 Hz Type: TERSA Diameter: 120 mm Number of planer knives: 4 pcs Speed: 5,000 rpm Maximum planing width: 520 mm Feed speeds: 5/8/12/18 m/min Availability: short-term Location: Solingen

Condition: new, Year of construction: 2022, New machine Year of manufacture: 2022 Dimensions and Weight Length approx. 1725 mm Width/Depth approx. 880 mm Weight approx. 270 kg Surface planer Max. cutting depth: 4 mm Extraction Connection Extraction port diameter thicknesser: 2 x 120 mm Thickness planer Min. working height: 3 mm Max. working height: 230 mm Max. cutting depth: 4 mm Godpfx Askwhykjlmjbl Electrical Data Drive motor power: 4 kW Connection voltage: 400 V Mains frequency: 50 Hz Cutterblock Type: TERSA Number of knives: 3 pcs Speed: 5200 rpm Max. planing width: 300 mm Feed Speed: 7 m/min Availability: short-term Stock location: Flörsheim

Condition: new, Year of construction: 2024, New machine Gbedpfow Rhkqox Almel Year of manufacture: 2024 Equipment and technical specifications: Maximum professional configuration, optionally with Tersa or spiral cutter block Equipped with TERSA cutter block for tool-free, second-fast planer knife changes TERSA planer knife system allows for exceptionally quiet operation Helically serrated steel infeed roller for consistent and uniform material feed Material feed with two speeds, powered by a separate motor Extra-long surfacing tables for easy and precise dressing of workpieces Work tables made from annealed and stress-relieved cast iron, robust and permanently flat Simultaneously rearward-opening surfacing tables for minimal setup times Thickness table adjustment via handwheel with numerical height display High machine weight ensures maximum precision and vibration-free operation Powerful industrial motor Robust steel/cast iron construction Chip removal starting from 0.2 mm (at minimum workpiece thickness of 3 mm) due to helically serrated feed roller (ideal for economical planing of precious hardwood) Quality – Made in Europe Equipment details: Tersa cutter block No adjustments or screwing required Blade changes in seconds Self-locking Exceptionally quiet operation Material feed: Helically serrated steel infeed rollers for consistent wood feed without markings Multiple teeth engage simultaneously for powerful feed Wear-free compared to rubber infeed rollers Permanently mounted extraction hood: With the fixed extraction hood, there is no need to change the extraction hose during retooling This saves valuable working time Simultaneous opening of surfacing tables: Both surfacing tables can be tilted up together, spring-assisted, for fast and convenient conversion to thicknessing mode in seconds Thickness table adjustment: FS 41 elite s with thickness table adjustment by handwheel and integrated indicator The thickness table is guided on four large-dimensioned spindles providing maximum stability in all operating conditions. A special lifting device keeps the table position perfectly stable even without locking. Anti-kickback devices: Massive anti-kickback devices prevent kickback of workpieces The 4-knife cutter block ensures optimal planing results Anodized aluminium surfacing fence: Large size (1200 x 150 mm) Easily adjustable Tiltable from 90° to 45° with scale Supplied with auxiliary fence for safe planing of narrow workpieces Digital version: With electric thickness table height adjustment and digital display Scope of delivery: Jointing/edge fence with round bar guide 2 feed speeds Tersa cutter block Technical Data Overall surfacing table length: 2200 mm Surfacing infeed table length: Surfacing table height: Surfacing working width: 410 mm Surfacing maximum cutting depth: 5 mm Surfacing fence dimensions: 1200 x 150 mm Surfacing fence tilt range: Thickness table dimensions: 775 x 410 mm Min. thicknessing height: 3 mm Max. thicknessing height: 240 mm Min. thicknessing workpiece length: Thicknessing feed speeds: 6 / 12 m/min Cutter block speed: 5000 rpm Cutter block diameter: 95 mm Number of planer knives: 4 pcs. Electric...

Condition: used, Year of construction: 2023, Used machine Year of manufacture: 2023 Condition: as new, machine is unused Gbedpfx Aew E Tzrolmol Equipment and technical specifications: - Spindle speeds: 3,500 / 6,000 / 8,000 / 10,000 rpm - Milling spindle tilt: 0 to -45° - Usable spindle length: 125 mm - Spindle arbor diameter: 30 mm - Speed display: LED indicator on the machine front - Max. tool diameter (standard): 240 mm - Max. lowerable tool diameter: 230 mm - Max. tool diameter for profile milling: 240 mm - Max. tool diameter for tenoning: 320 mm - Working table length: 1,200 mm - Working table width: 530 mm - Table height: 900 mm - Sliding table length: 1,200 mm - Sliding table width: 360 mm - Sliding table height: 142 mm - Extraction port diameter: 2 × 120 mm - Main drive motor power: 5.0 kW - Connection voltage: 400 V - Mains frequency: 50 Hz Dimensions: 1,200 × 2,000 mm Weight: 510 kg Availability: short-term Location: Saxony-Anhalt